Toward High-Performance Piezoresistive Polymer Derived SiOC Ceramics through Masked Stereolithography 3D Printing with ß-Silicon Carbide Nanopowder Reinforcement.

Enhancing the piezoresistivity of polymer-derived silicon oxycarbide ceramics (SiOCPDC ) is of great interest in the advancement of highly sensitive pressure/load sensor technology for use in harsh and extreme working conditions. However, a facile, low cost, and scalable approach to fabricate highly piezoresistive SiOCPDC below 1400 °C still remains a great challenge. Here, the fabrication and enhancement of piezoresistive properties of SiOCPDC reinforced with ß-SiC nanopowders (SiCNP ) through masked stereolithography-based 3D-printing and subsequent pyrolysis at 1100 °C are demonstrated. The presence of free carbon in SiCNP augments high piezoresistivity in the fabricated SiCNP -SiOCPDC composites even at lower pyrolysis temperatures. A gauge factor (GF) in the range of 4385-5630 and 6129-8987 with 0.25 and 0.50 wt% of SiCNP , respectively is demonstrated, for an applied pressure range of 0.5-5 MPa at ambient working conditions. The reported GF is significantly higher compared to those of any existing SiOCPDC materials. This rapid and facile fabrication route with significantly enhanced piezoresistive properties makes the 3D-printed SiCNP -SiOCPDC composite a promising high-performance material for the detection of pressure/load in demanding applications. Also, the overall robustness in mechanical properties and load-bearing capability ensures its long-term stability and makes it suitable for challenging and severe environment applications.

Electrical performance enhancement of a triboelectric nanogenerator based on epoxy resin/BaTiO3by Al nanopowder addition for low power electronic devices.

Triboelectric nanogenerators (TENGs) are crucial for applications such as smart sensors and bio-electronics. In the current work, we aimed for improved performance of TENGs with incorporation of BaTiO3powder, which is known for its strong ferroelectric properties, combining it with epoxy resin to improve the flexibility of our devices. We observed that our TENGs can operate for over 24 000 cycles with no degradation of function. Additionally, we improved the electrical performance of the TENGs by incorporating various aluminum concentrations that change the electronic properties in the form of mixed epoxy resin, BaTiO3, and Al nanopowders. To identify the optimum conditions for the best performance, we analyzed the electrical characteristics and material properties by employing scanning electron microscopy, energy dispersive x-ray spectroscopy, and x-ray diffractometry characterization techniques. Our findings suggest that this innovative combination of materials and optimization techniques can significantly improve the performance of TENGs, making them ideal for practical applications in various fields, such as low-power electronics, environmental monitoring and healthcare. Moreover, these enhanced TENGs can serve as sustainable and dependable energy sources for various applications.

Synthesis and Antimicrobial Analysis of High Surface Area Strontium-Substituted Calcium Phosphate Nanostructures for Bone Regeneration.

Continuous microwave-assisted flow synthesis has been used as a simple, more efficient, and low-cost route to fabricate a range of nanosized (<100 nm) strontium-substituted calcium phosphates. In this study, fine nanopowder was synthesized via a continuous flow synthesis with microwave assistance from the solutions of calcium nitrate tetrahydrate (with strontium nitrate as Sr2+ ion source) and diammonium hydrogen phosphate at pH 10 with a time duration of 5 min. The morphological characterization of the obtained powder has been carried out by employing techniques such as transmission electron microscopy, X-ray diffraction, and Brunauer-Emmett-Teller surface area analysis. The chemical structural analysis to evaluate the surface properties was made by using X-ray photoelectron spectroscopy. Zeta potential analysis was performed to evaluate the colloidal stability of the particles. Antimicrobial studies were performed for all the compositions using four bacterial strains and an opportunistic human fungal pathogen Macrophomina phaseolina. It was found that the nanoproduct with high strontium content (15 wt% of strontium) showed pronounced antibacterial potential against M. luteus while it completely arrested the fungal growth after 48 h by all of its concentrations. Thus the synthesis strategy described herein facilitated the rapid production of nanosized Sr-substituted CaPs with excellent biological performance suitable for a bone replacement application.

Atmospheric Pressure Solvothermal Synthesis of Nanoscale SnO2 and Its Application in Microextrusion Printing of a Thick-Film Chemosensor Material for Effective Ethanol Detection.

The atmospheric pressure solvothermal (APS) synthesis of nanocrystalline SnO2 (average size of coherent scattering regions (CSR)-7.5 ± 0.6 nm) using tin acetylacetonate as a precursor was studied. The resulting nanopowder was used as a functional ink component in microextrusion printing of a tin dioxide thick film on the surface of a Pt/Al2O3/Pt chip. Synchronous thermal analysis shows that the resulting semiproduct is transformed completely into tin dioxide nanopowder at 400 °C within 1 h. The SnO2 powder and the resulting film were shown to have a cassiterite-type structure according to X-ray diffraction analysis, and IR spectroscopy was used to establish the set of functional groups in the material composition. The microstructural features of the tin dioxide powder were analyzed using scanning (SEM) and transmission (TEM) electron microscopy: the average size of the oxide powder particles was 8.2 ± 0.7 nm. Various atomic force microscopy (AFM) techniques were employed to investigate the topography of the oxide film and to build maps of surface capacitance and potential distribution. The temperature dependence of the electrical conductivity of the printed SnO2 film was studied using impedance spectroscopy. The chemosensory properties of the formed material when detecting H2, CO, NH3, C6H6, C3H6O and C2H5OH, including at varying humidity, were also examined. It was demonstrated that the obtained SnO2 film has an increased sensitivity (the sensory response value was 1.4-63.5) and selectivity for detection of 4-100 ppm C2H5OH at an operating temperature of 200 °C.

Transition Metal Substituted Barium Hexaferrite-Modified Electrode: Application as Electrochemical Sensor of Acetaminophen.

This study used substituted barium hexaferrites, which were previously prepared and reported by the authors, to detect acetaminophen by the modification of a conventional glassy carbon electrode (GCE), which led to promising results. The synthesis of this electrode-modifying material was conducted using a citrate sol gel process. A test synthesis using glycerin and propylene glycol revealed that glycerin produced a better result, while less positive anodic potential values were associated with the electrooxidation of N-acetyl-p-aminophenol (NAP). Excellent electroactivity was exhibited by the cobalt-substituted barium-hexaferrite-nanomaterial-modified electrode. A good linear relationship between the concentration and the current response of acetaminophen (paracetamol) was obtained with a detection limit of (0.255 ± 0.005) µM for the Ba1.0Co1.22Fe11.41O18.11 GCE, (0.577 ± 0.007) µM for the Ba1.14Cu0.82Fe11.65O18.02 GCE, and (0.595 ± 0.008) µM for the bare GCE. The levels of NAP in a real sample of urine were quantitatively analyzed using the proposed method, with recovery ranges from 96.6% to 101.0% and 93.9% to 98.4% for the modified electrode with Cobalt-substituted barium hexaferrites (CoFM) and Copper-substituted barium hexaferrites (CuFM), respectively. These results confirm the high electrochemical activity of Ba1.0Co1.22Fe11.41O18.11 nanoparticles and thus their potential for use in the development of sensing devices for substances of pharmaceutical interest, such as acetaminophen (NAP).

Biocatalytic System Made of 3D Chitin, Silica Nanopowder and Horseradish Peroxidase for the Removal of 17α-Ethinylestradiol: Determination of Process Efficiency and Degradation Mechanism.

The occurrence of 17α-ethinylestradiol (EE2) in the environment and its removal have drawn special attention from the scientific community in recent years, due to its hazardous effects on human and wildlife around the world. Therefore, the aim of this study was to produce an efficient enzymatic system for the removal of EE2 from aqueous solutions. For the first time, commercial silica nanopowder and 3D fibrous chitinous scaffolds from Aplysina fistularis marine sponge were used as supports for horseradish peroxidase (HRP) immobilization. The effect of several process parameters onto the removal mechanism of EE2 by enzymatic conversion and adsorption of EE2 were investigated here, including system type, pH, temperature and concentrations of H2O2 and EE2. It was possible to fully remove EE2 from aqueous solutions using system SiO2(HRP)-chitin(HRP) over a wide investigated pH range (5-9) and temperature ranges (4-45 °C). Moreover, the most suitable process conditions have been determined at pH 7, temperature 25 °C and H2O2 and EE2 concentrations equaling 2 mM and 1 mg/L, respectively. As determined, it was possible to reuse the nanoSiO2(HRP)-chitin(HRP) system to obtain even 55% EE2 degradation efficiency after five consecutive catalytic cycles.

Recent advances in heavy metal recovery from wastewater by biogenic sulfide precipitation.

Biological sulfide precipitation by sulfate reducing bacteria (SRB) is an emerging technique for the recovery of heavy metals from metal contaminated wastewater. Advantages of this technique include low capital cost, ability to form highly insoluble salts, and capability to remove and recover heavy metals even at very low concentrations. Therefore, sulfate reduction under anaerobic conditions has become a suitable alternative for the treatment of wastewaters that contain metals. However, bioreactor configurations for recovery of metals from sulfate rich metallic wastewater have not been explored widely. Moreover, the recovered metal sulfide nanoparticles could be applied in various fields such as solar cells, dye degradation, electroplating, etc. Hence, metal recovery in the form of nanoparticles from wastewater could serve as an incentive for industries. The simultaneous metal removal and recovery can be achieved in either a single-stage or multistage systems. This paper aims to present an overview of the different bioreactor configurations for the treatment of wastewater containing sulfate and metal along with their advantages and drawbacks for metal recovery. Currently followed biological strategies to mitigate sulfate and metal rich wastewater are evaluated in detail in this review.

Elemental Selenium Enriched Nanofiber Production.

This study aimed to produce electrospun nanofibers from a polyvinyl butyral polymer (PVB) solution enriched with red and grey selenium nanoparticles. Scanning electron microscopic analysis was used to observe the samples, evaluate the fiber diameters, and reveal eventual artifacts in the nanofibrous structure. Average fiber diameter is determined by manually measuring the diameters of randomly selected fibers on scanning electron microscopic (SEM) images. The obtained nanofibers are amorphous with a diameter of approximately 500 nm, a specific surface area of approx. 8 m2 g-1, and 5093 km cm-3 length. If the red and grey selenium nanoparticles were produced in powder form and suspended to the ethanolic solution of PVB then they were located inside and outside the fiber. When selenium nanoparticles were synthesized in the PVB solution, then they were located only inside the fiber. These nanofiber sheets enriched with selenium nanoparticles could be a good candidate for high-efficiency filter materials and medical applications.

Viscosity and Rheological Properties of Graphene Nanopowders Nanofluids.

The dynamic viscosity and rheological properties of two different non-aqueous graphene nano-plates-based nanofluids are experimentally investigated in this paper, focusing on the effects of solid volume fraction and shear rate. For each nanofluid, four solid volume fractions have been considered ranging from 0.1% to 1%. The rheological characterization of the suspensions was performed at 20 ∘C, with shear rates ranging from 10-1s-1 to 103s-1, using a cone-plate rheometer. The Carreau-Yasuda model has been successfully applied to fit most of the rheological measurements. Although it is very common to observe an increase of the viscosity with the solid volume fraction, we still found here that the addition of nanoparticles produces lubrication effects in some cases. Such a result could be very helpful in the domain of heat extraction applications. The dependence of dynamic viscosity with graphene volume fraction was analyzed using the model of Vallejo et al.

Can plastic waste management be a novel solution in combating the novel Coronavirus (COVID-19)? A short research note.

The year 2020 has been noted to be one of major calamity the world over, in which the majority of efforts in research and development have been dedicated towards combating the threat of the novel Coronavirus (COVID-19). Ever since the announcement of COVID-19 as a pandemic, such efforts were dedicated towards the research of its spread and vaccination. Yet still, the world might reach a resolution via an environmental solution that various entities have overlooked, with a plethora of environmental benefits vis-à-vis waste management. In this short communication, the possibility of using plastic solid waste as a substrate to employ copper, and copper alloys and their nanocomposite nanopowders to be used as permanent surface protective coats, is presented. The fact that we present such materials to be of waste origin, is an added value advantage to their beneficial advantage of developing various commodities and products that could be used in our daily lives. Furthermore, the fact that such recyclable materials are susceptible to antiviral properties and chemicals, is an added value that we should not neglect.