Hexylation Stabilises Twisted Backbone Configurations in the Prototypical Low-Bandgap Copolymer PCDTBT.

Conjugated donor-acceptor copolymers hold great potential as materials for high-performance organic photovoltaics, organic transistors and organic thermoelectric devices. Their low optical bandgap is achieved by alternation of donor and acceptor moieties along the polymer chain, leading to a pronounced charge-transfer character of electronic excitations. However, the influence of appended side chains and of chemical defects of the backbone on their photophysical and conformational properties remains largely unexplored on the level of individual chains. Here, we employ room temperature single-molecule photoluminescence spectroscopy on four compounds based on the prototypical copolymer PCDTBT with systematically changed chemical structure. Our results show that an increasing density of statistically added hexyl chains to the TBT comonomer distorts the molecular conformation, likely through the increase of average dihedral angles along the backbone. We find that, although the conformation becomes more twisted with high hexyl density, the side chains appear to stabilize the backbone in this twisted conformation. In addition, we demonstrate that homocoupling defects along the backbone barely influence the PL spectra of single chains, and thus intra-chain electronic properties.

Tailoring the Position of Ester Group on N-Alkyl Chains of Benzotriazole-based Small Molecule Acceptors for High-Performance Organic Solar Cells.

Side chain engineering plays a vital role in exploring high-performance small molecule acceptors (SMAs) for organic solar cells (OSCs). In this work, we designed and synthesized a series of A-DA'D-A type SMAs by introducing different N-substituted alkyl and ester alkyl side chains on benzotriazole (BZ) central unit and aimed to investigate the effect of different ester substitution positions on photovoltaic performances. All the new SMAs with ester groups exhibit lower the lowest unoccupied molecular orbital (LUMO) energy levels and more blue-shifted absorption, but relatively higher absorption coefficients than alkyl chain counterpart. After blending with the donor PM6, the ester side chain-based devices demonstrate enhanced charge mobility, reduced amorphous intermixing domain size and long-lived charge transfer state compared to the alkyl chain counterpart, which are beneficial to achieve higher short-circuit current density (Jsc ) and fill factor (FF), simultaneously. Thereinto, the PM6 : BZ-E31 based device achieves a higher power conversion efficiency (PCE) of 18.33 %, which is the highest PCE among the OSCs based on the SMAs with BZ-core. Our work demonstrated the strategy of ester substituted side chain is a feasible and effective approach to develop more efficient SMAs for OSCs.

Improving the Corrosion Protection of Poly(phenylene methylene) Coatings by Side Chain Engineering: The Case of Methoxy-Substituted Copolymers.

This work aims to improve the corrosion protection features of poly(phenylene methylene) (PPM) by sidechain engineering inserting methoxy units along the polymer backbone. The influence of side methoxy groups at different concentrations (4.6% mol/mol and 9% mol/mol) on the final polymer properties was investigated by structural and thermal characterization of the resulting copolymers: co-PPM 4.6% and co-PPM 9%, respectively. Then, coatings were processed by hot pressing the polymers powder on aluminum alloy AA2024 and corrosion protection properties were evaluated exposing samples to a 3.5% w/v NaCl aqueous solution. Anodic polarization tests evidenced the enhanced corrosion protection ability (i.e., lower current density) by increasing the percentage of the co-monomer. Coatings made with co-PPM 9% showed the best protection performance with respect to both PPM blend and PPM co-polymers reported so far. Electrochemical response of aluminum alloy coated with co-PPM 9% was monitored over time under two "artificially-aged" conditions, that are: (i) a pristine coating subjected to potentiostatic anodic polarization cycles, and (ii) an artificially damaged coating at resting condition. The first scenario points to accelerating the corrosion process, the second one models damage of the coating potentially occurring either due to natural deterioration or due to any accidental scratching of the polymer layer. In both cases, an intrinsic self-healing phenomenon was indirectly argued by the time evolution of the impedance and of the current density of the coated systems. The degree of restoring to the "factory conditions" by co-polymer coatings after self-healing events is eventually discussed.

Highly Processable Covalent Organic Framework Gel Electrolyte Enabled by Side-Chain Engineering for Lithium-Ion Batteries.

Although covalent organic frameworks (COFs) with a graphene-like structure present unique chemical and physical properties, they are essentially insoluble and infusible crystalline powders with poor processability, hindering their further practical applications. How to improve the processability of COF materials is a major challenge in this field. In this contribution, we proposed a general side-chain engineering strategy to construct a gel-state COF with high processability. This method takes advantages of large and soft branched alkyl side chains as internal plasticizers to achieve the gelation of the COF. We systematically studied the influence of the length of the side chain on the COF gel formation. Benefitting from their machinability and flexibility, this novel COF gel can be easily processed into gel-type electrolytes with specific shape and thickness, which were further applied to assemble lithium-ion batteries that exhibited high cycling stability.

Direct observation of backbone planarization via side-chain alignment in single bulky-substituted polythiophenes.

The backbone conformation of conjugated polymers affects, to a large extent, their optical and electronic properties. The usually flexible substituents provide solubility and influence the packing behavior of conjugated polymers in films or in bad solvents. However, the role of the side chains in determining and potentially controlling the backbone conformation, and thus the optical and electronic properties on the single polymer level, is currently under debate. Here, we investigate directly the impact of the side chains by studying the bulky-substituted poly(3-(2,5-dioctylphenyl)thiophene) (PDOPT) and the common poly(3-hexylthiophene) (P3HT), both with a defined molecular weight and high regioregularity, using low-temperature single-chain photoluminescence (PL) spectroscopy and quantum-classical simulations. Surprisingly, the optical transition energy of PDOPT is significantly (∼2,000 cm-1 or 0.25 eV) red-shifted relative to P3HT despite a higher static and dynamic disorder in the former. We ascribe this red shift to a side-chain induced backbone planarization in PDOPT, supported by temperature-dependent ensemble PL spectroscopy. Our atomistic simulations reveal that the bulkier 2,5-dioctylphenyl side chains of PDOPT adopt a clear secondary helical structural motif and thus protect conjugation, i.e., enforce backbone planarity, whereas, for P3HT, this is not the case. These different degrees of planarity in both thiophenes do not result in different conjugation lengths, which we found to be similar. It is rather the stronger electronic coupling between the repeating units in the more planar PDOPT which gives rise to the observed spectral red shift as well as to a reduced calculated electron-hole polarization.

Tunable Properties of Nature-Inspired N,N'-Alkylated Riboflavin Semiconductors.

A series of novel soluble nature-inspired flavin derivatives substituted with short butyl and bulky ethyl-adamantyl alkyl groups was prepared via simple and straightforward synthetic approach with moderate to good yields. The comprehensive characterization of the materials, to assess their application potential, has demonstrated that the modification of the conjugated flavin core enables delicate tuning of the absorption and emission properties, optical bandgap, frontier molecular orbital energies, melting points, and thermal stability. Moreover, the thin films prepared thereof exhibit smooth and homogeneous morphology with generally high stability over time.

High-Performance Polymer Solar Cells Achieved by Introducing Side-Chain Heteroatom on Small-Molecule Electron Acceptor.

Side chains of photovoltaic materials play an important role in determining charge transport property, film morphology, and the corresponding device performance. In this work, two new acceptor materials, ATT-6 and ATT-7 with different side chains, m-hexylphenyl and m-hexyloxyphenyl on the indacenodithiophene, are designed and synthesized for applications in non-fullerene polymer solar cells. ATT-7 shows a higher absorption coefficient, increased crystallinity, and improved electron mobility in comparison with ATT-6. Using wide-bandgap polymer poly[(2,6-(4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)-benzo[1,2-b:4,5-b']dithiophene))-alt-(5,5-(1',3'-di-2-thienyl-5',7'-bis(2-ethylhexyl)benzo[1',2'-c:4',5'-c']dithiophene-4,8-dione)] (PBDB-T) as donor, optimized devices based on PBDB-T:ATT-7 and PBDB-T:ATT-6 delivers power conversion efficiencies of 10.30% and 8.39%, respectively. The higher performance of ATT-7-based device can be attributed to efficient exciton dissociation, reduced bimolecular recombination, and enhanced and balanced charge carrier mobilities. These results indicate that side-chain modification is an easy but efficient way in the design of high-performance non-fullerene acceptors.

Small Changes With Big Consequences: Swapping Two Atoms In Side Chains Changes Phenylene-Ethynylene Packing And Fluorescence.

Engineering the properties of conjugated materials in the solid state is an unsolved, ongoing challenge important to fundamental understanding of how non-covalent interactions dictate packing and key properties, as well as the development of technologies based in organic optoelectronics. The most common design paradigm of such materials divide them into a "main chain" with extended conjugation, the chemical structure of which determines optoelectronic properties, and "side chains" not conjugated to the backbone, which provide solubility when they are long alkyl chains. This paper describes comparisons between phenylene-ethynylene molecules in which slight changes to the structure of "side chains"-swapping hydrogen and fluorine atomic position on an aromatic ring-results in unexpectedly large changes in the solid-state optical properties. In a pair of anisyl-terminated three-ring phenylene-ethynylenes, switching the side chain arenes of benzyl esters from 2,4,6-trifluoro to 2,3,6-trifluoro results in a shift in fluorescence emission spectra of over 100 nm, as well as the opposite direction of force-induced shifting of emission. Through a combination X-ray crystal structures, electronic structure calculations, and comparisons with other derivatives, we describe how the 2,4,6-trifluorinated side chains yield cofacial fluoroarene-arene stacking interactions that twist the PE backbone out of conjugation, while the 2,3,6-trifluoro side chains do not stack, instead yielding more coplanar PE backbones that form intermolecular aggregates. Overall, this work demonstrates how slight modifications to parts of conjugated materials normally considered ancillary to optoelectronic properties can determine their solid-state properties, epitomizing the challenge of rational design but at the same time offering opportunities for materials discovery and improved understanding of non-covalent interactions.

Asymmetric Alkyl Side-Chain Engineering of Naphthalene Diimide-Based n-Type Polymers for Efficient All-Polymer Solar Cells.

The design and synthesis of three n-type conjugated polymers based on a naphthalene diimide-thiophene skeleton are presented. The control polymer, PNDI-2HD, has two identical 2-hexyldecyl side chains, and the other polymers have different alkyl side chains; PNDI-EHDT has a 2-ethylhexyl and a 2-decyltetradecyl side chain, and PNDI-BOOD has a 2-butyloctyl and a 2-octyldodecyl side chain. These copolymers with different alkyl side chains exhibit higher melting and crystallization temperatures, and stronger aggregation in solution, than the control copolymer PNDI-2HD that has the same side chain. Polymer solar cells based on the electron-donating copolymer PTB7-Th and these novel copolymers exhibit nearly the same open-circuit voltage of 0.77 V. Devices based on the copolymer PNDI-BOOD with different side chains have a power-conversion efficiency of up to 6.89%, which is much higher than the 4.30% obtained with the symmetric PNDI-2HD. This improvement can be attributed to the improved charge-carrier mobility and the formation of favorable film morphology. These observations suggest that the molecular design strategy of incorporating different side chains can provide a new and promising approach to developing n-type conjugated polymers.

Side-Chain Effects on the Thermoelectric Properties of Fluorene-Based Copolymers.

Three conjugated polymers with alkyl chains of different lengths are designed and synthesized, and their structure-property relationship as organic thermoelectric materials is systematically elucidated. All three polymers show similar photophysical properties, thermal properties, and mechanical properties; however, their thermoelectric performance is influenced by the length of their side chains. The length of the alkyl chain significantly influences the electrical conductivity of the conjugated polymers, and polymers with a short alkyl chain exhibit better conductivity than those with a long alkyl chain. The length of the alkyl chain has little effect on the Seebeck coefficient. Only a slight increase in the Seebeck coefficient is observed with the increasing length of the alkyl chain. The purpose of this study is to provide comprehensive insight into fine-tuning the thermoelectric properties of conjugated polymers as a function of side-chain engineering, thereby providing a novel perspective into the design of high-performance thermoelectric conjugated polymers.

Side-chain-bulk effects on the molecular packing and photovoltaic performance of benzotrithiophene-benzooxadiazole conjugated copolymers.

Two alternating donor-acceptor conjugated polymers, PBTTBO-C13 C11 and PBTTBO-C13 C8 , comprising 5-alkylbenzo[1,2-b:3,4-b':5,6-d'']trithiophene (BTT) as the donor and 4,7-bis(4-dodecylthien-2-yl)benzo[1,2,5]oxadiazole (BO) as the acceptor, with different alkyl side-chain architectures on their BTT units are synthesized, and their bulk heterojunction photovoltaic properties when blended with the fullerene PC71 BM are characterized. Even a slight change in the length of the alkyl chain of the BTT units influences the steric bulk to such a degree that it substantially affects the molecular packing of the polymers and the performance of their photovoltaic devices. The bulkier side chains of the polymer PBTTBO-C13 C11 not only prevent its crystallization, but also suppress its light-absorption coefficient relative to that of PBTTBO-C13 C8 , as evidenced by X-ray diffraction and UV/Vis absorption studies, presumably because of weakened intermolecular interactions. Moreover, the polymer bearing bulkier side chains, PBTTBO-C13 C11 , is less miscible with PC71 BM than PBTTBO-C13 C8 , and this characteristic determines the morphology of their annealed blended films, as shown by TEM studies. The best efficiency is obtained with a device containing an annealed PBTTBO-C13 C8 /PC71 BM (1/2 w/w) active layer that was maintained at 120 °C for 10 min, which shows a power conversion efficiency of 6.2 %, an open-circuit voltage of 0.75 V, a short-circuit current density of 12.6 mA cm(-2) , and a fill factor of 66 %.

Advancing optoelectronic characteristics of Diketopyrrolopyrrole-Based molecules as donors for organic and as hole transporting materials for perovskite solar cells.

A stable and efficient hole-transport material (HTM) is crucial for high-performance perovskite solar cells (PSCs). A 2,2',7,7'-tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9'-spirobifluorene (Spiro-MeOTAD) being used widely to prepare highly efficient PSCs. However, Spiro-MeOTAD has some limitations due to its complex synthesis, which increases its cost, and it also requires dopants to improve its performance. Therefore, we designed thirteen unique small-molecule-based HTMs (MK1-MK13), which are easy to synthesize, highly cost-effective, and don't require dopants to prepare efficient PSCs. Their electrical and optical properties are then investigated theoretically using advanced quantum chemical approaches. The designed molecules showed lower energy gaps and improved optical and optoelectronic characteristics because of the improved phase inversion geometry. The detailed photo-physical and optoelectronic characteristics have been studied using density functional theory (DFT) and time-dependent (TD-DFT) calculations. Moreover, we investigated the impact of holes and electrons and the density of states, open-circuit voltage, frontier molecular orbital, transition density matrix, and other structural and photovoltaic characteristics of these materials. Among these, the MK3 molecule possesses the much narrower optical band gap of 1.04 eV and absorbance (λ max) of 684 nm, respectively. In addition, a profound investigation of the MK3/PC61BM blend shows excellent charge transfer at the acceptor-donor interface. Therefore, our proposed technique is necessary for generating appropriate photovoltaic materials for efficient optoelectronic devices and is helpful in further advancing the field.

High-Efficiency Binary and Ternary Organic Solar Cells Based on Novel Nonfused-Ring Electron Acceptors.

In this study, three nonfused-ring electron acceptors (2TT, 2TT-C6-F, and 2TT-C11-F) with the same steric hindrance groups (2,4,6-tripropylbenzene) are designed and synthesized and the impact of electron-withdrawing and lateral alkyl side chains on the performance of binary and ternary organic solar cells (OSCs) is explored. For the binary OSCs, 2TT-C11-F with IC-2F terminal groups and lateral undecyl side chains display a red shifted absorption spectrum and suitable energy levels, and the corresponding blend film exhibits appropriate phase separation and crystallinity. Thus, binary OSCs based on 2TT-C11-F achieve an impressive power conversion efficiency of 13.03%, much higher than the efficiencies of those based on 2TT (9.68%) and 2TT-C6-F (12.11%). In the ternary OSCs, 2TT with CC terminal groups and lateral hexyl side chains exhibit complementary absorption and cascade energy levels with a host binary system (D18:BTP-eC9-4F). Hence, the ternary OSCs based on 2TT achieve a remarkable efficiency of 19.39%, ranking among the highest reported values. The research yields comprehensive 2TT-series nonfused-ring electron acceptors, demonstrating their great potential for the fabrication of high-performance binary and ternary OSCs.

High-Performance Organic Electrochemical Transistors Achieved by Optimizing Structural and Energetic Ordering of Diketopyrrolopyrrole-Based Polymers.

For optimizing steady-state performance in organic electrochemical transistors (OECTs), both molecular design and structural alignment approaches must work in tandem to minimize energetic and microstructural disorders in polymeric mixed ionic-electronic conductor films. Herein, a series of poly(diketopyrrolopyrrole)s bearing various lengths of aliphatic-glycol hybrid side chains (PDPP-mEG; m = 2-5) is developed to achieve high-performance p-type OECTs. PDPP-4EG polymer with the optimized length of side chains exhibits excellent crystallinity owing to enhanced lamellar and backbone interactions. Furthermore, the improved structural ordering in PDPP-4EG films significantly decreases trap state density and energetic disorder. Consequently, PDPP-4EG-based OECT devices produce a mobility-volumetric capacitance product ([µC*]) of 702 F V-1 cm-1 s-1 and a hole mobility of 6.49 ± 0.60 cm2 V-1 s-1 . Finally, for achieving the optimal structural ordering along the OECT channel direction, a floating film transfer method is employed to reinforce the unidirectional orientation of polymer chains, leading to a substantially increased figure-of-merit [µC*] to over 800 F V-1 cm-1 s-1 . The research demonstrates the importance of side chain engineering of polymeric mixed ionic-electronic conductors in conjunction with their anisotropic microstructural optimization to maximize OECT characteristics.

Manipulating Alkyl Inner Side Chain of Acceptor for Efficient As-Cast Organic Solar Cells.

As-cast organic solar cells (OSCs) possess tremendous potential for low-cost commercial applications. Herein, five small-molecule acceptors (A1-A5) are designed and synthesized by selectively and elaborately extending the alkyl inner side chain flanking on the pyrrole motif to prepare efficient as-cast devices. As the extension of the alkyl chain, the absorption spectra of the films are gradually blue-shifted from A1 to A5 along with slightly uplifted lowest unoccupied molecular orbital energy levels, which is conducive for optimizing the trade-off between short-circuit current density and open-circuit voltage of the devices. Moreover, a longer alkyl chain improves compatibility between the acceptor and donor. The in situ technique clarifies that good compatibility will prolong molecular assembly time and assist in the preferential formation of the donor phase, where the acceptor precipitates in the framework formed by the donor. The corresponding film-formation dynamics facilitate the realization of favorable film morphology with a suitable fibrillar structure, molecular stacking, and vertical phase separation, resulting in an incremental fill factor from A1 to A5-based devices. Consequently, the A3-based as-cast OSCs achieve a top-ranked efficiency of 18.29%. This work proposes an ingenious strategy to manipulate intermolecular interactions and control the film-formation process for constructing high-performance as-cast devices.

High Open-Circuit Voltage Organic Solar Cells with 19.2% Efficiency Enabled by Synergistic Side-Chain Engineering.

Restricted by the energy-gap law, state-of-the-art organic solar cells (OSCs) exhibit relatively low open-circuit voltage (VOC) because of large nonradiative energy losses (ΔEnonrad). Moreover, the trade-off between VOC and external quantum efficiency (EQE) of OSCs is more distinctive; the power conversion efficiencies (PCEs) of OSCs are still <15% with VOCs of >1.0 V. Herein, the electronic properties and aggregation behaviors of non-fullerene acceptors (NFAs) are carefully considered and then a new NFA (Z19) is delicately designed by simultaneously introducing alkoxy and phenyl-substituted alkyl chains to the conjugated backbone. Z19 exhibits a hypochromatic-shifted absorption spectrum, high-lying lowest unoccupied molecular orbital energy level and ordered 2D packing mode. The D18:Z19-based blend film exhibits favorable phase separation with face-on dominated molecular orientation, facilitating charge transport properties. Consequently, D18:Z19 binary devices afford an exciting PCE of 19.2% with a high VOC of 1.002 V, surpassing Y6-2O-based devices. The former is the highest PCE reported to date for OSCs with VOCs of >1.0 V. Moreover, the ΔEnonrad of Z19- (0.200 eV) and Y6-2O-based (0.155 eV) devices are lower than that of Y6-based (0.239 eV) devices. Indications are that the design of such NFA, considering the energy-gap law, could promote a new breakthrough in OSCs.

Nonhalogenated Solvent-Processed Efficient Ternary All-Polymer Solar Cells Enabled by the Introduction of a Naphthyloxy Group into the Side Chain of Polymer Donors.

Conjugated polymer donors are crucial for enhancing the power conversion efficiencies (PCEs) in all-polymer solar cells (All-PSCs) in nonhalogenated solvents. In this work, three wide-band-gap polymer donors (Sil-D1, Ph-Sil-D1, and Nap-Sil-D1) based on dithienobenzothiadiazole (DTBT) and benzodithiophene (BDT) donor moieties optimized by side chain engineering were designed and synthesized. Alkyl (Sil-D1), phenyloxy (Ph-Sil-D1), and naphthyloxy (Nap-Sil-D1) alkyl siloxane side chain units were incorporated into these polymer donors, respectively. Notably, the Nap-Sil-D1 polymer donor had a greater conjugation length, π-electron delocalization, and improved dipole moment. The deepest highest occupied molecular orbital level of Nap-Sil-D1, with a high absorption coefficient, showed better aggregation properties. In addition, reduced bimolecular recombination and trap-state density generated a high charge transfer to cause a significant enhancement of open-circuit voltage, current density, and fill factor values of 0.94 V, 25.5 mA/cm2, and 70.4%, respectively, for the Nap-Sil-D1-blended All-PSC ternary device (PM6:Nap-Sil-D1:PY-IT), with the highest PCE of 16.8% in the o-xylene solvent, compared to other polymers (Sil-D1 and Ph-Sil-D1) with PCEs of 15.5 and 16.2%. As a result, this optimized device architecture was found to be the most promising as a nonhalogenated solvent processed in additive-free ternary All-PSCs with good stability.

Hybrid Cycloalkyl-Alkyl Chain-Based Symmetric/Asymmetric Acceptors with Optimized Crystal Packing and Interfacial Exciton Properties for Efficient Organic Solar Cells.

Hybrid cycloalkyl-alkyl side chains are considered a unique composite side-chain system for the construction of novel organic semiconductor materials. However, there is a lack of fundamental understanding of the variations in the single-crystal structures as well as the optoelectronic and energetic properties generated by the introduction of hybrid side chains in electron acceptors. Herein, symmetric/asymmetric acceptors (Y-C10ch and A-C10ch) bearing bilateral and unilateral 10-cyclohexyldecyl are designed, synthesized, and compared with the symmetric acceptor 2,2'-((2Z,2'Z)-((12,13-bis(2-butyloctyl)-3,9 bis(ethylhexyl)-12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2″,3″':4',5']thieno[2',3':4,5] pyrrolo[3,2-g]thieno[2',3':4,5]thieno[3,2-b]indole-2,10- diyl)bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (L8-BO). The stepwise introduction of 10-cyclohexyldecyl side chains decreases the optical bandgap, deepens the energy level, and enables the acceptor molecules to pack closely in a regular manner. Crystallographic analysis demonstrates that the 10-cyclohexyldecyl chain endows the acceptor with a more planar skeleton and enforces more compact 3D network packing, resulting in an active layer with higher domain purity. Moreover, the 10-cyclohexyldecyl chain affects the donor/acceptor interfacial energetics and accelerates exciton dissociation, enabling a power conversion efficiency (PCE) of >18% in the 2,2'-((2Z,2'Z)-((12,13-bis(2-ethylhexyl)-3,9-diundecyl12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2″,3″':4',5']thieno[2',3':4,5]pyrrolo[3,2-g]thieno[2',3':4,5]thieno[3,2-b]indole-2,10-diyl)bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (Y6) (PM6):A-C10ch-based organic solar cells (OSCs). Importantly, the incorporation of Y-C10ch as the third component of the PM6:L8-BO blend results in a higher PCE of 19.1%. The superior molecular packing behavior of the 10-cyclohexyldecyl side chain is highlighted here for the fabrication of high-performance OSCs.

Organic Thermoelectric Materials from n-Type Polymer Semiconductors.

Organic thermoelectric (OTE) materials have garnered increasing attention due to their potential application in wearable/flexible TE generator for energy harvesting. To meet the practical application of thermoelectric device, high-performance p- and n-type OTE materials are both necessary. In the past few years, improved n-type polymer semiconductors have developed rapidly in the OTE field; however, their thermoelectric performance is still lagging behind p-type counterparts. Therefore, more efforts should be made to enhance n-type polymer TE performance, including development of novel molecule structure, synthesis of new dopants and optimization of device engineering. In this Review, we highlight the effects of molecular structure and side chain length and polarity of n-type polymer semiconductors on the TE performance such as electron transport, electrical conductivity, and power factor. Finally, further perspectives and challenges are also discussed to provide useful guidelines for the design of high-performance n-type OTE materials.

High-Performance n-Type Organic Thermoelectrics Enabled by Synergistically Achieving High Electron Mobility and Doping Efficiency.

n-Doped polymers with high electrical conductivity (σ) are still very scarce in organic thermoelectrics (OTEs), which limits the development of efficient organic thermoelectric generators. A series of fused bithiophene imide dimer-based polymers, PO8, PO12, and PO16, incorporating distinct oligo(ethylene glycol) side-chain to optimize σ is reported here. Three polymers show a monotonic electron mobility decrease as side-chain size increasing due to the gradually lowered film crystallinity and change of backbone orientation. Interestingly, polymer PO12 with a moderate side-chain size delivers a champion σ up to 92.0 S cm-1 and a power factor (PF) as high as 94.3 µW m-1 K-2 in the series when applied in OTE devices. The PF value is among the highest ones for the solution-processing n-doped polymers. In-depth morphology studies unravel that the moderate crystallinity and the formation of 3D conduction channel derived from bimodal orientation synergistically contribute to high doping efficiency and large charge carrier mobility, thus resulting in high performance for the PO12-based OTEs. The results demonstrate the great power of simple tuning of side chain in developing n-type polymers with substantial σ for improving organic thermoelectric performance.