Minimizing the Carrier Collection Loss of the Neutral-Color Transparent Crystalline-silicon Solar Modules via Hybrid Electrode Design.

Transparent solar cells can be used where conventional solar cells are inapplicable, such as, in glass windows of buildings; however, reports on modularization, which is essential for their commercialization, are scarce. Here, a novel modularization method has been proposed for the fabrication of transparent solar cells and a 100-cm2 neutral-color transparent crystalline-silicon solar module has been developed using a hybrid electrode comprising a microgrid electrode and an edge busbar electrode. The transparent solar module exhibits a power conversion efficiency (PCE) of 11.94 and 13.14% when connected in series and in parallel, respectively, with an average visible transmittance of 20%. Additionally, the module exhibits negligible losses in PCE (lower than 0.23%) in outdoor, mechanical-load, and damp-heat (at 85°C/85% RH) stability tests, indicating high stability. The transparent solar module proposes here could facilitate the commercialization of transparent solar cells.

Volatile Dual-Solvent Assisted Intermediate Phase Regulation for Anti-Solvent-Free Perovskite Photovoltaics.

The unprecedented development of perovskite solar cells (PSCs) makes them one of the most promising candidates for terawatt-scale green energy production with low cost. However, the high boiling point solvents during the solution-processed film deposition cause anisotropic crystal growth and toxic solvent vapor during high-throughput manufacturing. Here, a dual-component green solvent consisting of isopropyl acetate and acetonitrile is proposed to form a volatile perovskite precursor, which can realize the high-quality perovskite thin film deposition by intermediate phase regulation. A room-temperature stable perovskite intermediate phase is constructed with the engagement of isopropyl acetate as co-solvent, which suppresses the exploding nucleation rate in volatile perovskite precursor, providing a fine grain growth rate and wide processing window in scalable film deposition. The corresponding PSCs fabricated by blade coating without anti-solvents or gas quenching achieve power conversion efficiency (PCE) of 16.37 % and 15.29 % for the areas of 14.08 cm2 and 37.83 cm2 , respectively.

Asymmetrically Substituted 10H,10'H-9,9'-Spirobi[acridine] Derivatives as Hole-Transporting Materials for Perovskite Solar Cells.

Hole-transporting materials (HTMs) based on the 10H, 10'H-9,9'-spirobi [acridine] core (BSA50 and BSA51) were synthesized, and their electronic properties were explored. Experimental and theoretical studies show that the presence of rigid 3,6-dimethoxy-9H-carbazole moieties in BSA 50 brings about improved hole mobility and higher work function compared to bis(4-methoxyphenyl)amine units in BSA51, which increase interfacial hole transportation from perovskite to HTM. As a result, perovskite solar cells (PSCs) based on BSA50 boost power conversion efficiency (PCE) to 22.65 %, and a PSC module using BSA50 HTM exhibits a PCE of 21.35 % (6.5×7 cm) with a Voc of 8.761 V and FF of 79.1 %. The unencapsulated PSCs exhibit superior stability to devices employing spiro-OMeTAD, retaining nearly 90 % of their initial efficiency after 1000 h operation output. This work demonstrates the high potential of molecularly engineered spirobi[acridine] derivatives as HTMs as replacements for spiro-OMeTAD.

A Purified, Solvent-Intercalated Precursor Complex for Wide-Process-Window Fabrication of Efficient Perovskite Solar Cells and Modules.

A high-purity methylammonium lead iodide complex with intercalated dimethylformamide (DMF) molecules, CH3 NH3 PbI3 ⋅DMF, is introduced as an effective precursor material for fabricating high-quality solution-processed perovskite layers. Spin-coated films of the solvent-intercalated complex dissolved in pure dimethyl sulfoxide (DMSO) yielded thick, dense perovskite layers after thermal annealing. The low volatility of the pure DMSO solvent extended the allowable time for low-speed spin programs and considerably relaxed the precision needed for the antisolvent addition step. An optimized, reliable fabrication method was devised to take advantage of this extended process window and resulted in highly consistent performance of perovskite solar cell devices, with up to 19.8 % power-conversion efficiency (PCE). The optimized method was also used to fabricate a 22.0 cm2 , eight-cell module with 14.2 % PCE (active area) and 8.64 V output (1.08 V/cell).

Anomalous Electroluminescence Characteristics of Perovskite Modules.

Spatially resolved photoluminescence (PL) and electroluminescence (EL) imaging technologies play a crucial role in evaluating the performance and stability of photovoltaic devices. However, their application in perovskite devices presents unique challenges. In this study, we report a discrepancy between the electrical performance of perovskite solar modules (PSMs) and the EL images. Following the application of a reverse bias voltage, we observed an increase in EL brightness associated with prolonged carrier lifetime and transport length. Furthermore, cross-sectional Kelvin probe force microscopy identified a significant potential increase primarily at the electron-transport layer (ETL) side after reverse bias, suggesting the presence of defective ETL/perovskite interfaces with filled hole traps. To address this EL mismatch, we proposed a mild reverse current recovery method aimed at aligning EL images with the cell performance without compromising device efficiency. This approach effectively mitigates discrepancies, ensuring alignment between the device performance and EL imaging. Our study underscores that caution is required when utilizing EL imaging to monitor spatial homogeneity in PSMs for future industrial production.

Highly Efficient and Stable Perovskite Solar Modules Based on FcPF6 Engineered Spiro-OMeTAD Hole Transporting Layer.

Li-TFSI doped spiro-OMeTAD is widely recognized as a beneficial hole transport layer (HTL) in perovskite solar cells (PSCs), contributing to high device efficiencies. However, the uncontrolled migration of lithium ions (Li+) during device operation has impeded its broad adoption in scalable and stable photovoltaic modules. Herein, an additive strategy is proposed by employing ferrocenium hexafluorophosphate (FcPF6) as a relay medium to enhance the hole extraction capability of the spiro-OMeTAD via the instant oxidation function. Besides, the novel Fc-Li interaction effectively restricts the movement of Li+. Simultaneously, the dissociative hexafluorophosphate group is cleverly exploited to regulate the unstable iodide species on the perovskite surface, further inhibiting the formation of migration channels and stabilizing the interfaces. This modification leads to power conversion efficiencies (PCEs) reaching 22.13% and 20.27% in 36 cm2 (active area of 18 cm2) and 100 cm2 (active area of 56 cm2) perovskite solar modules (PSMs), respectively, with exceptional operational stability obtained for over 1000 h under the ISOS-L-1 procedure. The novel FcPF6-based engineering approach is pivotal for advancing the industrialization of PSCs, particularly those relying on high-performance spiro-OMeTAD- based HTLs.

Delayed Crystallization Kinetics Allowing High-Efficiency All-Polymer Photovoltaics with Superior Upscaled Manufacturing.

Though encouraging performance is achieved in small-area organic photovoltaics (OPVs), reducing efficiency loss when evoluted to large-area modules is an important but unsolved issue. Considering that polymer materials show benefits in film-forming processability and mechanical robustness, a high-efficiency all-polymer OPV module is demonstrated in this work. First, a ternary blend consisting of two polymer donors, PM6 and PBQx-TCl, and one polymer acceptor, PY-IT, is developed, with which triplet state recombination is suppressed for a reduced energy loss, thus allowing a higher voltage; and donor-acceptor miscibility is compromised for enhanced charge transport, thus resulting in improved photocurrent and fill factor; all these contribute to a champion efficiency of 19% for all-polymer OPVs. Second, the delayed crystallization kinetics from solution to film solidification is achieved that gives a longer operation time window for optimized blend morphology in large-area module, thus relieving the loss of fill factor and allowing a record efficiency of 16.26% on an upscaled module with an area of 19.3 cm2 . Besides, this all-polymer system also shows excellent mechanical stability. This work demonstrates that all-polymer ternary systems are capable of solving the upscaled manufacturing issue, thereby enabling high-efficiency OPV modules.

Scalable Solution-Processed Hybrid Electron Transport Layers for Efficient All-Perovskite Tandem Solar Modules.

All-perovskite tandem solar cells offer the potential to surpass the Shockley-Queisser (SQ) limit efficiency of single-junction solar cells while maintaining the advantages of low-cost and high-productivity solution processing. However, scalable solution processing of electron transport layer (ETL) in p-i-n structured perovskite solar subcells remains challenging due to the rough perovskite film surface and energy level mismatch between ETL and perovskites. Here, scalable solution processing of hybrid fullerenes (HF) with blade-coating on both wide-bandgap (≈1.80 eV) and narrow-bandgap (≈1.25 eV) perovskite films in all-perovskite tandem solar modules is developed. The HF, comprising a mixture of fullerene (C60 ), phenyl C61 butyric acid methyl ester, and indene-C60 bisadduct, exhibits improved conductivity, superior energy level alignment with both wide- and narrow-bandgap perovskites, and reduced interfacial nonradiative recombination when compared to the conventional thermal-evaporated C60 . With scalable solution-processed HF as the ETLs, the all-perovskite tandem solar modules achieve a champion power conversion efficiency of 23.3% (aperture area = 20.25 cm2 ). This study paves the way to all-solution processing of low-cost and high-efficiency all-perovskite tandem solar modules in the future.

Synergistic Redox Modulation for High-Performance Nickel Oxide-Based Inverted Perovskite Solar Modules.

Nickel oxide (NiOx)-based inverted perovskite solar cells stand as promising candidates for advancing perovskite photovoltaics towards commercialization, leveraging their remarkable stability, scalability, and cost-effectiveness. However, the interfacial redox reaction between high-valence Ni4+ and perovskite, alongside the facile conversion of iodide in perovskite into I2, significantly deteriorates the performance and reproducibility of NiOx-based perovskite photovoltaics. Here, potassium borohydride (KBH4) is introduced as a dual-action reductant, which effectively avoids the Ni4+/perovskite interface reaction and mitigates the iodide-to-I2 oxidation within perovskite film. This synergistic redox modulation significantly suppresses nonradiative recombination and increases the carrier lifetime. As a result, an impressive power conversion efficiency of 24.17% for NiOx-based perovskite solar cells is achieved, and a record efficiency of 20.2% for NiOx-based perovskite solar modules fabricated under ambient conditions. Notably, when evaluated using the ISOS-L-2 standard protocol, the module retains 94% of its initial efficiency after 2000 h of continuous illumination under maximum power point at 65 °C in ambient air.

Equally Efficient Perovskite Solar Cells and Modules Fabricated via N-Ethyl-2-Pyrrolidone Optimized Vacuum-Flash.

Efficiency reduction in perovskite solar cells (PSCs) during the magnification procedure significantly hampers commercialization. Vacuum-flash (VF) has emerged as a promising method to fabricate PSCs with consistent efficiency across scales. However, the slower solvent removal rate of VF compared to the anti-solvent method leads to perovskite films with buried defects. Thus, this work employs low-toxic Lewis base ligand solvent N-ethyl-2-pyrrolidone (NEP) to improve the nucleation process of perovskite films. NEP, with a mechanism similar to that of N-methyl-2-pyrrolidone in FA-based perovskite formation, enhances the solvent removal speed owing to its lower coordination ability. Based on this strategy, p-i-n PSCs with an optimized interface attain a power conversion efficiency (PCE) of 24.19% on an area of 0.08 cm2. The same nucleation process enables perovskite solar modules (PSMs) to achieve a certified PCE of 23.28% on an aperture area of 22.96 cm2, with a high geometric fill factor of 97%, ensuring nearly identical active area PCE (24%) in PSMs as in PSCs. This strategy highlights the potential of NEP as a ligand solvent choice for the commercialization of PSCs.

Nucleation Regulation and Mesoscopic Dielectric Screening in α-FAPbI3.

While significant advancements in power conversion efficiencies (PCEs) of α-FAPbI3perovskite solar cells (PSCs) have been made, attaining controllable perovskite crystallization is still a considerable hurdle. This challenge stems from the initial formation of δ-FAPbI3, a more energetically stable phase than the desired black α-phase, during film deposition. This disrupts the heterogeneous nucleation of α-FAPbI3, causing the formation of mixed phases and defects. To this end, polarity engineering using molecular additives, specifically ((methyl-sulfonyl)phenyl)ethylamines (MSPEs) are introduced. The findings reveal that the interaction of PbI2-MSPEs-FAI intermediates is enhanced with the increased polarity of MSPEs, which in turn expedites the nucleation of α-FAPbI3. This leads to the development of high-quality α-FAPbI3 films, characterized by vertical crystal orientation and reduced residual stresses. Additionally, the increased dipole moment of MSPE at perovskite grain boundaries attenuates Coulomb attractions among charged defects and screens carrier capture process, thereby diminishing non-radiative recombination. Utilizing these mechanisms, PSCs treated with highly polar 2-(4-MSPE) achieve an impressive PCE of 25.2% in small-area devices and 20.5% in large-area perovskite solar modules (PSMs) with an active area of 70 cm2. These results demonstrate the effectiveness of this strategy in achieving controllable crystallization of α-FAPbI3, paving the way for scalable-production of high-efficiency PSMs.

Efficient and Stable Perovskite Solar Modules Enabled by Inhibited Escape of Volatile Species.

The intrinsically weak bonding structure in halide perovskite materials makes components in the thin films volatile, leading to the decomposition of halide perovskite materials. The reactions within the perovskite film are reversible provided that components do not escape the thin films. Here, a holistic approach is reported to improve the efficiency and stability of PSMs by preventing the effusion of volatile components. Specifically, a method for in situ generation of channel barrier layers for perovskite photovoltaic modules is developed. The resulting PSMs attain a certified aperture PCE of 21.37%, and possess remarkable continuous operation stability for maximum power point tracking (MPPT) of T90 > 1100 h in ambient air, and damp heat (DH) tracking of T93 > 1400 h.

Efficient and Stable Inverted Perovskite Solar Modules Enabled by Solid-Liquid Two-Step Film Formation.

A considerable efficiency gap exists between large-area perovskite solar modules and small-area perovskite solar cells. The control of forming uniform and large-area film and perovskite crystallization is still the main obstacle restricting the efficiency of PSMs. In this work, we adopted a solid-liquid two-step film formation technique, which involved the evaporation of a lead iodide film and blade coating of an organic ammonium halide solution to prepare perovskite films. This method possesses the advantages of integrating vapor deposition and solution methods, which could apply to substrates with different roughness and avoid using toxic solvents to achieve a more uniform, large-area perovskite film. Furthermore, modification of the NiOx/perovskite buried interface and introduction of Urea additives were utilized to reduce interface recombination and regulate perovskite crystallization. As a result, a large-area perovskite film possessing larger grains, fewer pinholes, and reduced defects could be achieved. The inverted PSM with an active area of 61.56 cm2 (10 × 10 cm2 substrate) achieved a champion power conversion efficiency of 20.56% and significantly improved stability. This method suggests an innovative approach to resolving the uniformity issue associated with large-area film fabrication.

Nitrogen-Blowing Assisted Strategy for Fabricating Large-Area Organic Solar Modules with an Efficiency of 15.6.

Organic solar cells (OSCs) are one of the most promising photovoltaic technologies due to their affordability and adaptability. However, upscaling is a critical issue that hinders the commercialization of OSCs. A significant challenge is the lack of cost-effective and facile techniques to modulate the morphology of the active layers. The slow solvent evaporation leads to an unfavorable phase separation, thus resulting in a low power conversion efficiency (PCE) of organic solar modules. Here, a nitrogen-blowing assisted method is developed to fabricate a large-area organic solar module (active area = 12 cm2) utilizing high-boiling-point solvents, achieving a PCE of 15.6%. The device fabricated with a high-boiling-point solvent produces a more uniform and smoother large-area film, and the assistance of nitrogen-blowing accelerates solvent evaporation, resulting in an optimized morphology with proper phase separation and finer aggregates. Moreover, the device fabricated by the nitrogen-blowing assisted method exhibits improved exciton dissociation, balanced carrier mobility, and reduced charge recombination. This work proposes a universal and cost-effective technique for the fabrication of high-efficiency organic solar modules.

Large Orientation Angle Buried Substrate Enables Efficient Flexible Perovskite Solar Cells and Modules.

Flexible perovskite solar cells (f-PSCs) have emerged as potential candidates for specific mechanical applications owing to their high foldability, efficiency, and portability. However, the power conversion efficiency (PCE) of f-PSC remains limited by the inferior contact between perovskite and flexible buried substrate. Here, an asymmetric π-extended self-assembled monolayer (SAM) (4-(9H-dibenzo[a,c]carbazol-9-yl)butyl)phosphonic acid (A-4PADCB) is reported as a buried substrate for efficient inverted f-PSCs. Employing this design strategy, A-4PADCB exhibits a significant orientation angle away from the surface normal, homogenizing the distribution of contact potentials. This enhancement improves the SAM/perovskite interface quality, controlling the growth of favorable perovskite films with low defect density and slight tensile stress. Integration of A-4PADCB into small-area f-PSCs and large-area flexible perovskite solar modules with an aperture area of 20.84 cm2 achieves impressive PCEs of up to 25.05% and 20.64% (certified 19.51%), respectively. Moreover, these optimized A-4PADCB-based f-PSCs possess enhanced light, thermal, and mechanical stability. This research paves a promising avenue toward the design of SAM-buried substrates with a large orientation angle, regulating perovskite growth, and promoting the commercialization of large-area flexible perovskite photovoltaics.

An Equalized Flow Velocity Strategy for Perovskite Colloidal Particles in Flexible Perovskite Solar Cells.

The non-uniform distribution of colloidal particles in perovskite precursor results in an imbalanced response to the shear force during flexible printing process. Herein, it is observed that the continuous disordered migration occurring in perovskite inks significantly contributes to the enlargement of colloidal particles size and diminishes the crystallization activity of the inks. Therefore, a molecular encapsulation architecture by glycerol monostearate to mitigate colloidal particles collisions in the precursor ink, while simultaneously homogenizing the size distribution of perovskite colloids to minimize their diffusion disparities, is devised. The utilization of colloidal particles with a molecular encapsulation structure enables the achievement of uniform deposition during the printing process, thereby effectively balancing the crystallization rate and phase transition in the film and facilitating homogeneous crystallization of perovskite films. The large-area flexible perovskite device (1.01 cm2 and 100 cm2) fabricated through printing processes, achieves an efficiency of 24.45% and 15.87%, respectively, and manifests superior environmental stability, maintaining an initial efficiency of 91% after being stored in atmospheric ambiences for 150 days (unencapsulated). This work demonstrates that the dynamic evolution process of colloidal particles in both the precursor ink and printing process represents a crucial stride toward achieving uniform crystallization of perovskite films.

Over 19% Efficiency Perovskite Solar Modules by Simultaneously Suppressing Cation Deprotonation and Iodide Oxidation.

Perovskite solar cells (PSCs) based on sputtered nickel oxide (NiOx) hole transport layer have emerged as promising configuration due to their good stability, cost-effectiveness, and scalability. However, the adverse chemical redox reaction at the NiOx/perovskite interface remains an ever-present problem that has not yet been well solved. To address this issue before, the problems that cation deprotonation and iodide oxidation that occurred in precursor solution easily result in the interfacial chemical reaction should be prevented. Hence, we report an efficient strategy to simultaneously suppress the interfacial reaction and stabilize the precursor solution by incorporating a reducing and weakly acidic stabilizer, l-ascorbic acid (l-AA). l-AA can reduce I2 generated in the precursor solution and during the interfacial reaction to I-. Furthermore, the protons ionized by adjacent enol hydroxyl groups in l-AA effectively impede the deprotonation of organic cations in the precursor solution as well as at the NiOx/perovskite interface resulting from the chemical reaction. Attributing to the improved crystallization of the perovskite film and the suppression of the interfacial reaction by l-AA, the inverted PSC based on such good light absorber achieves an impressive power conversion efficiency (PCE) of 22.72% along with a high open-circuit voltage of 1.19 V. Notably, further introducing l-AA into the large-area solar modules by the slot-die coating method in air enables a remarkable PCE of 19.17%, which reaches one of the highest PCEs reported for inverted perovskite solar modules (PSMs) (active area >50 cm2) to date. l-AA located at the buried interface also forms a barrier layer that can prevent undesirable chemical reactions at the NiOx/perovskite interface, significantly enhancing the device stability of solar cells and PSMs. These findings in our work provide important guidance for improving the NiOx/perovskite interface and the fabrication of highly efficient, low-cost, and large-area PSMs.

Inner/Outer Side Chain Engineering of Non-Fullerene Acceptors for Efficient Large-Area Organic Solar Modules Based on Non-Halogenated Solution Processing in Air.

Achieving efficient and large-area organic solar modules via non-halogenated solution processing is vital for the commercialization yet challenging. The primary hurdle is the conservation of the ideal film-formation kinetics and bulk-heterojunction (BHJ) morphology of large-area organic solar cells (OSCs). A cutting-edge non-fullerene acceptor (NFA), Y6, shows efficient power conversion efficiencies (PCEs) when processed with toxic halogenated solvents, but exhibits poor solubility in non-halogenated solvents, resulting in suboptimal morphology. Therefore, in this study, the impact of modifying the inner and outer side-chains of Y6 on OSC performance is investigated. The study reveals that blending a polymer donor, PM6, with one of the modified NFAs, namely N-HD, achieved an impressive PCE of 18.3% on a small-area OSC. This modified NFA displays improved solubility in o-xylene at room temperature, which facilitated the formation of a favorable BHJ morphology. A large-area (55 cm2) sub-module delivered an impressive PCE of 12.2% based on N-HD using o-xylene under ambient conditions. These findings underscore the significant impact of the modified Y6 derivatives on structural arrangements and film processing over a large-area module at room temperature. Consequently, these results are poised to deepen the comprehension of the scaling challenges encountered in OSCs and may contribute to their commercialization.

LiTFSI-Free Hole Transport Materials for Robust Perovskite Solar Cells and Modules with High Efficiencies.

Lithium bis(trifluoromethane) sulfonamide (LiTFSI) and oxygen-doped organic semiconductors have been frequently used to achieve record power conversion efficiencies of perovskite solar cells (PSCs). However, this conventional doping process is time-consuming and leads to poor device stability due to the incorporation of Li ions. Herein, aiming to accelerate the doping process and remove the Li ions, we report an alternative p-doping process by mixing a new small-molecule organic semiconductor, N2,N2,N7,N7-tetrakis (4-methoxyphenyl)-9-(4-(octyloxy) phenyl)-9H carbazole-2,7-diamine (labeled OH44) and its preoxidized form OH44+(TFSI-). With this method, a champion efficiency of 21.8% has been achieved for small-area PSCs, which is superior to the state-of-the-art EH44 and comparable with LiTFSI and oxygen-doped spiro-OMeTAD. Moreover, the stability of OH44-based PSCs is improved compared with those of EH44, maintaining more than 85% of its initial efficiency after aging in an ambient condition without encapsulation for 1000 h. In addition, we achieved efficiencies of 14.7 and 12.6% for the solar modules measured with a metal mask of 12.0 and 48.0 cm2, respectively, which demonstrated the scalability of this method.

Highest-Efficiency Flexible Perovskite Solar Module by Interface Engineering for Efficient Charge-Transfer.

The electron-transport layer (ETL) plays an important role in improving the performance of flexible perovskite solar cells (F-PSCs). Herein, a room-temperature-processed SnO2 :OH ETL is demonstrated, that exhibits reduced defect density, in particular lower oxygen vacancy concentration, with better energy band alignment and more wettable surface for quality perovskite deposition. More importantly, an efficient electron-transfer channel is produced between the ETL and the perovskite layer due to the formation of hydrogen bonds at the interface, resulting in enhanced electron extraction from the perovskite. As a result, the efficiency of a large-area (36.50 cm2 ) flexible perovskite solar module based on MAPbI3 is increased to as high as 18.71%; this is thought to be the highest reported PCE value for flexible perovskite solar modules to date. In addition, it exhibits high durability while maintaining over 83% of its initial PCE after flexing test cycles. Further, F-PSCs with SnO2 :OH show remarkably long-term stability, owing to a high quality of the perovskite film and a strong coupling between the SnO2 :OH and perovskite layer caused by hydrogen bonds, which successfully inhibits moisture permeation.