Enhanced Electron Transport and Mitigated Voltage Loss in Perovskite Photovoltaics Using Sb2O5@SnO2 Composite Electron Transport Layer.

The efficacy of electron transport layers (ETLs) is pivotal for optimizing the device performance of perovskite photovoltaic applications. However, colloidal dispersions of SnO2 are prone to aggregation and possess structural defects, such as terminal-hydroxyls (OHT) and oxygen vacancies (VOs), which can degrade the quality of ETLs, impede charge extraction and transport, and affect the nucleation and growth processes of the perovskite layer. In this study, the Sb(OH)4 - ions hydrolyzed from SbCl3 in colloidal dispersion can bind to defect sites and effectively stabilize the SnO2 nanocrystals are demonstrated. Upon oxidative annealing, a Sb2O5@SnO2 composite film is formed, in which the Sb2O5 not only mitigates the aforementioned defects but also broadens the energy range of unoccupied states through its dispersed conduction band. The increased electron affinity (EA) facilitates more efficient capture of photoexcited electrons from the perovskite layer, thus augmenting electron extraction and minimizing electron-hole recombination. As a result, a significant improvement in power conversion efficiency (PCE) from 22.60% to 24.54% is achieved, with an open circuit voltage (VOC) of up to 1.195 V, along with excellent stability of unsealed devices under various conditions. This study provides valuable insights for the understanding and design of ETLs in perovskite photovoltaic applications.

Template-Assisted Epitaxial Growth of Ordered SnO2 Nanorods Arrays with Different Hollow Structures for High-Performance Sodium Storage.

Anode materials for sodium ion batteries (SIBs) are confronted with severe volume expansion and poor electrical conductivity. Construction of assembled structures featuring hollow interior and carbon material modification is considered as an efficient strategy to address the issues. Herein, a novel template-assisted epitaxial growth method, ingeniously exploiting lattice matching nature, is developed to fabricate hollow ordered architectures assembled by SnO2 nanorods. SnO2 nanorods growing along [100] direction can achieve lattice-matched epitaxial growth on (110) plane of α-Fe2O3. Driven by the lattice matching, different α-Fe2O3 templates possessing different crystal plane orientations enable distinct assembly modes of SnO2, and four kinds of hollow ordered SnO2@C nanorods arrays (HONAs) with different morphologies including disc, hexahedron, dodecahedron and tetrakaidecahedron (denoted as Di-, He-, Do-, and Te-SnO2@C) are achieved. Benefiting from the synergy of hollow structure, carbon coating and ordered assembly structure, good structural integrity and stability and enhanced electrical conductivity are realized, resulting in impressive sodium storage performances when utilized as SIB anodes. Specifically, Te-SnO2@C HONAs exhibit excellent rate capability (385.6 mAh·g-1 at 2.0 A·g-1) and remarkable cycling stability (355.4 mAh·g-1 after 2000 cycles at 1.0 A·g-1). This work provides a promising route for constructing advanced SIB anode materials through epitaxial growth for rational structural design.

Methyltrimethoxysilane modified tin dioxide microspheres with hydrophobic networks and abundant adsorbed oxygen for efficient solid-phase microextraction of polychlorinated biphenyls.

Methyltrimethoxysilane (MTMS) modified tin dioxide microspheres (MTMS/SnO2) were prepared by a facile hydrothermal method and heated reflux reaction strategy. The characterization results indicate that the modification of MTMS induced the formation of a hydrophobic network within the composites, while maintaining abundant adsorbed oxygen species. Subsequently, the MTMS/SnO2 microspheres were used as a solid-phase microextraction (SPME) coating for the efficient extraction and sensitive determination of trace polychlorinated biphenyls (PCBs) in aqueous solutions coupled to gas chromatography-mass spectrometry. MTMS/SnO2 coating exhibited superior extraction performances for PCBs compared with commercial SPME and pure SnO2 microspheres coatings, owing to the hydrophobic crosslinking and adsorbed oxygen-enhanced hydrogen bonding. The proposed analytical method presented respectable linearity in the concentration range 0.25-1000 ng L-1, with low limits of detection varying from 0.036 to 0.14 ng L-1 for seven PCBs and excellent precision, with relative standard deviations of 5.7-9.8% for a single fiber and 8.2-13.1% for five fibers. Finally, the proposed method was successfully used for determination of PCBs in real water with recoveries ranging from 75.8 to 115.6%. This study proposed a new type SPME coating of MTMS/SnO2 microspheres, which extended the potential of SnO2 in capturing and determining organic pollutants.

Buried Interface Optimization for Flexible Perovskite Solar Cells with High Efficiency and Mechanical Stability.

The power conversion efficiency (PCE) and stability of perovskite solar cells (PSCs) are significantly reduced by defect-induced charge non-radiative recombination. Also, unexpected residual strain in perovskite films leads to an unfavorable impact on the stability and efficiency of PSCs, notably flexible PSCs (f-PSCs). Considering these problems, a thorough and effective strategy is proposed by incorporating phytic acid (PA) into SnO2 as an electron transport layer (ETL). With the addition of PA, the Sn inherent dangling bonds are passivated effectively and thus enhance the conductivity and electron mobility of SnO2 ETL. Meanwhile, the crystallization quality of perovskite is increased largely. Therefore, the interface/bulk defects are reduced. Besides, the residual strain of perovskite film is significantly reduced and the energy level alignment at the SnO2 /perovskite interface becomes more matched. As a result, the champion f-PSC obtains a PCE of 21.08% and rigid PSC obtains a PCE of 21.82%, obviously surpassing the PCE of 18.82% and 19.66% of the corresponding control devices. Notably, the optimized f-PSCs exhibit outstanding mechanical durability, after 5000 cycles of bending with a 5 mm bending radius, the SnO2 -PA-based device preserves 80% of the initial PCE, while the SnO2 -based device only remains 49% of the initial value.

Looking Outside the Square: The Growth, Structure, and Resilient Two-Dimensional Surface Electron Gas of Square SnO2 Nanotubes.

Nanotechnology has delivered an amazing range of new materials such as nanowires, tubes, ribbons, belts, cages, flowers, and sheets. However, these are usually circular, cylindrical, or hexagonal in nature, while nanostructures with square geometries are comparatively rare. Here, a highly scalable method is reported for producing vertically aligned Sb-doped SnO2 nanotubes with perfectly-square geometries on Au nanoparticle covered m-plane sapphire using mist chemical vapor deposition. Their inclination can be varied using r- and a-plane sapphire, while unaligned square nanotubes of the same high structural quality can be grown on silicon and quartz. X-ray diffraction measurements and transmission electron microscopy show that they adopt the rutile structure growing in the [001] direction with (110) sidewalls, while synchrotron X-ray photoelectron spectroscopy reveals the presence of an unusually strong and thermally resilient 2D surface electron gas. This is created by donor-like states produced by the hydroxylation of the surface and is sustained at temperatures above 400 °C by the formation of in-plane oxygen vacancies. This persistent high surface electron density is expected to prove useful in gas sensing and catalytic applications of these remarkable structures. To illustrate their device potential, square SnO2 nanotube Schottky diodes and field effect transistors with excellent performance characteristics are fabricated.

Distinctive Electric Properties of Group 14 Oxides: SiO2, SiO, and SnO2.

The oxides of group 14 have been widely used in numerous applications in glass, ceramics, optics, pharmaceuticals, and food industries and semiconductors, photovoltaics, thermoelectrics, sensors, and energy storage, namely, batteries. Herein, we simulate and experimentally determine by scanning kelvin probe (SKP) the work functions of three oxides, SiO2, SiO, and SnO2, which were found to be very similar. Electrical properties such as electronic band structure, electron localization function, and carrier mobility were also simulated for the three crystalline oxides, amorphous SiO, and surfaces. The most exciting results were obtained for SiO and seem to show Poole-Frankel emissions or trap-assisted tunneling and propagation of surface plasmon polariton (SPP) with nucleation of solitons on the surface of the Aluminum. These phenomena and proposed models may also describe other oxide-metal heterojunctions and plasmonic and metamaterials devices. The SiO2 was demonstrated to be a stable insulator interacting less with the metals composing the cell than SnO2 and much less than SiO, configuring a typical Cu/SiO2/Al cell potential well. Its surface charge carrier mobility is small, as expected for an insulator. The highest charge carrier mobility at the lowest conduction band energy is the SnO2's and the most symmetrical the SiO's with a similar number of electron holes at the conduction and valence bands, respectively. The SnO2 shows it may perform as an n-type semiconductor.

KIT-5-Assisted Synthesis of Mesoporous SnO2 for High-Performance Humidity Sensors with a Swift Response/Recovery Speed.

Developing highly efficient semiconductor metal oxide (SMOX) sensors capable of accurate and fast responses to environmental humidity is still a challenging task. In addition to a not so pronounced sensitivity to relative humidity change, most of the SMOXs cannot meet the criteria of real-time humidity sensing due to their long response/recovery time. The way to tackle this problem is to control adsorption/desorption processes, i.e., water-vapor molecular dynamics, over the sensor's active layer through the powder and pore morphology design. With this in mind, a KIT-5-mediated synthesis was used to achieve mesoporous tin (IV) oxide replica (SnO2-R) with controlled pore size and ordering through template inversion and compared with a sol-gel synthesized powder (SnO2-SG). Unlike SnO2-SG, SnO2-R possessed a high specific surface area and quite an open pore structure, similar to the KIT-5, as observed by TEM, BET and SWAXS analyses. According to TEM, SnO2-R consisted of fine-grained globular particles and some percent of exaggerated, grown twinned crystals. The distinctive morphology of the SnO2-R-based sensor, with its specific pore structure and an increased number of oxygen-related defects associated with the powder preparation process and detected at the sensor surface by XPS analysis, contributed to excellent humidity sensing performances at room temperature, comprised of a low hysteresis error (3.7%), sensitivity of 406.8 kΩ/RH% and swift response/recovery speed (4 s/6 s).

Chemical fabrication, structural characterization and photocatalytic water splitting application of Sr-doped SnO2nanoparticles.

Semiconductor photocatalysis has gained considerable attention in recent years due to their enabling nature to convert solar energy into fuels of renewable hydrocarbon. However, many of them suffer from some drawbacks like the inability to visible light irradiation and wide band gaps. Herein, we have synthesized monophasic strontium (Sr) doped SnO2nanoparticles by a cost-effective and environmental friendly hydrothermal method. As-synthesized nanoparticles showed rutile crystalline structure with irregular and rough cubical shape and no other elemental impurities. Sr-doped SnO2nanoparticles show a constant decrease in bandgap with increasing dopant concentration, which is estimated for excellent photocatalytic activity. The photocatalytic water splitting of as-prepared Sr-doped SnO2nanoparticles for H2generation shows a large influence of the increasing dopant concentration related to the narrowing bandgap on H2generation rate. Hence, the tunable bandgap with adjusted dopant concentration indicates that band gap tuning through doping for produced nanostructures may open up a new opportunities for photocatalytic and other optoelectronic applications.

Investigation on Sensing Performance of Highly Doped Sb/SnO2.

Tin dioxide (SnO2) is the most-used semiconductor for gas sensing applications. However, lack of selectivity and humidity influence limit its potential usage. Antimony (Sb) doped SnO2 showed unique electrical and chemical properties, since the introduction of Sb ions leads to the creation of a new shallow band level and of oxygen vacancies acting as donors in SnO2. Although low-doped SnO2:Sb demonstrated an improvement of the sensing performance compared to pure SnO2, there is a lack of investigation on this material. To fill this gap, we focused this work on the study of gas sensing properties of highly doped SnO2:Sb. Morphology, crystal structure and elemental composition were characterized, highlighting that Sb doping hinders SnO2 grain growth and decreases crystallinity slightly, while lattice parameters expand after the introduction of Sb ions into the SnO2 crystal. XRF and EDS confirmed the high purity of the SnO2:Sb powders, and XPS highlighted a higher Sb concentration compared to XRF and EDS results, due to a partial Sb segregation on superficial layers of Sb/SnO2. Then, the samples were exposed to different gases, highlighting a high selectivity to NO2 with a good sensitivity and a limited influence of humidity. Lastly, an interpretation of the sensing mechanism vs. NO2 was proposed.

Investigations into the Antifungal, Photocatalytic, and Physicochemical Properties of Sol-Gel-Produced Tin Dioxide Nanoparticles.

Transmission electron microscopy (TEM), atomic force microscopy (AFM), X-ray diffraction (XRD), energy dispersive X-ray (EDX), scanning electron microscopy (SEM), diffuse reflectance spectroscopy (DRS), and Fourier transform infrared (FTIR) spectroscopy were applied to evaluate the tin dioxide nanoparticles (SnO2 NPs) amalgamated by the sol-gel process. XRD was used to examine the tetragonal-shaped crystallite with an average size of 26.95 (±1) nm, whereas the average particle size estimated from the TEM micrograph is 20.59 (±2) nm. A dose-dependent antifun3al activity was performed against two fungal species, and the activity was observed to be increased with an increase in the concentration of SnO2 NPs. The photocatalytic activity of SnO2 NPs in aqueous media was tested using Rhodamine 6G (Rh-6G) under solar light illumination. The Rh-6G was degraded at a rate of 0.96 × 10-2 min for a total of 94.18 percent in 350 min.

Atomic layer deposition for rutile structure TiO2thin films using a SnO2seed layer and low temperature heat treatment.

We study the rutile-TiO2film deposition with a high-kvalue using a SnO2seed layer and a low temperature heat treatment. Generally, heat treatment over 600 °C is required to obtain the rutile-TiO2film. However, By using a SnO2seed layer, we obtained rutile-TiO2films with heat treatments as low as 400 °C. The XPS analysis confirms that the SnO2and TiO2film were deposited. The XRD analysis showed that a heat treatment at 400 °C after depositing the SnO2and TiO2films was effective in obtaining the rutile-TiO2film when the SnO2film was thicker than 10 nm. The TEM/EDX analysis show that no diffusion in the thin film between TiO2and SnO2. The dielectric constant of the TiO2film deposited on the SnO2film (20 nm) was 67, which was more than twice as high as anatase TiO2dielectric constant (Anatase TiO2dielectric constant : 15-40). The current density was 10-4A cm-2at 0.7 V and this value confirmed that the leakage current was not affected by the SnO2seed layer.

Preparation and Research of a High-Performance ZnO/SnO2 Humidity Sensor.

A high-performance zinc oxide/tin dioxide (ZnO/SnO2) humidity sensor was developed using a simple solvothermal method. The sensing mechanism of the ZnO/SnO2 humidity sensor was evaluated by analyzing its complex impedance spectra. The experimental results prove that the ZnO/SnO2 composite material has a larger specific surface area than pure SnO2, which allows the composite material surface to adsorb more water to enhance the response of the ZnO/SnO2 humidity sensor. ZnO can also contribute to the generation of oxygen-rich vacancies on the ZnO/SnO2 composite material surface, allowing it to adsorb a large amount of water and rapidly decompose water molecules into conductive ions to increase the response and recovery speed of the ZnO/SnO2 humidity sensor. These characteristics allowed the Z/S-2 humidity sensor to achieve a higher response (1,225,361%), better linearity, smaller hysteresis (6.6%), faster response and recovery speeds (35 and 8 s, respectively), and long-term stability at 11-95% relative humidity. The successful preparation of the ZnO/SnO2 composite material also provides a new direction for the design of SnO2-based resistance sensors with high humidity-sensing performance.

Structure, Surface Morphology, Chemical Composition, and Sensing Properties of SnO2 Thin Films in an Oxidizing Atmosphere.

We conducted experiments on SnO2 thin layers to determine the dependencies between the stoichiometry, electrochemical properties, and structure. This study focused on features such as the film structure, working temperature, layer chemistry, and atmosphere composition, which play a crucial role in the oxygen sensor operation. We tested two kinds of resistive SnO2 layers, which had different grain dimensions, thicknesses, and morphologies. Gas-sensing layers fabricated by two methods, a rheotaxial growth and thermal oxidation (RGTO) process and DC reactive magnetron sputtering, were examined in this work. The crystalline structure of SnO2 films synthesized by both methods was characterized using XRD, and the crystallite size was determined from XRD and AFM measurements. Chemical characterization was carried out using X-ray photoelectron (XPS) and Auger electron (AES) spectroscopy for the surface and the near-surface film region (in-depth profiles). We investigated the layer resistance for different oxygen concentrations within a range of 1-4%, in a nitrogen atmosphere. Additionally, resistance measurements within a temperature range of 423-623 K were analyzed. We assumed a flat grain geometry in theoretical modeling for comparing the results of measurements with the calculated results.

Experimental Evidence of CO2 Photoreduction Activity of SnO2 Nanoparticles.

Tin dioxide (SnO2 ) has intrinsic characteristics that do not favor its photocatalytic activity. However, we evidenced that surface modification can positively influence its performance for CO2 photoreduction in the gas phase. The hydroxylation of the SnO2 surface played a role in the CO2 affinity decreasing its reduction potential. The results showed that a certain selectivity for methane (CH4 ), carbon monoxide (CO), and ethylene (C2 H4 ) is related to different SnO2 hydrothermal annealing. The best performance was seen for SnO2 annealed at 150 °C, with a production of 20.4 µmol g-1 for CH4 and 16.45 µmol g-1 for CO, while for SnO2 at 200 °C the system produced more C2 H4 , probably due to a decrease of surface -OH groups.

Stability improvement for dried droplet pretreatment by suppression of coffee ring effect using electrochemical anodized nanoporous tin dioxide substrate.

A novel nanoporous analytical platform is reported to improve the stability of the dried droplet method (DDM). This nanoporous platform was made of tin dioxide (Np SnO2) substrate by electrochemical anodization from tin (Sn) slide. The DDM is a widely used sample pretreatment in analytical chemistry that involves placing a droplet of solution onto the substrate and drying for analytical testing. However, during the droplet drying process, the solutes would converge at the droplet edge and cause inhomogeneous solutes distribution. This is the coffee ring effect (CRE). The Np SnO2 has irregular nanopores, which allows droplet solutions to penetrate into the substrate rather than spreading out, effectively suppressing CRE. Theoretical models were built to explain the formation of CRE on blank tin (Sn) substrate and suppression of CRE on Np SnO2. Better results were obtained in detecting lithium (Li) using the Np SnO2 by laser-induced breakdown spectroscopy (LIBS). The line scanning results indicated that the Li emission line (670.8 nm) intensities on Np SnO2 substrate had lower relative standard deviation (RSD = 3.3%) than those on Sn substrate (RSD = 31.5%), which illustrate suppression of CRE and stability improvement on Np SnO2 substrate. Furthermore, Li calibration curves were built for LIBS with DDM. The curve using Np SnO2 substrate had better linearity (R2 = 0.997), higher precision (RSD = 4.2%), and higher sensitivity (LOD = 0.13 mg/L) than that by Sn substrate (R2 = 0.954, RSD = 17%, and LOD = 1.21 mg/L). All in all, the anodic Np SnO2 substrate can suppress CRE in DDM and hence improve the stability and precision of subsequent analysis. Graphical abstract.

Photocatalytic activity study of coated anatase-rutile titania nanoparticles with nanocrystalline tin dioxide based on the statistical analysis.

Titania nanoparticles with two crystalline structures (anatase-rutile) and coated titania with different amount of tin dioxide (A-R-S#1 and A-R-S#2) are prepared through hydrolysis method. X-ray diffraction analysis (XRD) confirmed the presence of both anatase and rutile structures in the synthesized titania nanoparticles. In addition, the characteristic peak of tin dioxide in A-R-S#2 was higher than that of A-R-S#1. The photocatalytic activity of the prepared photocatalysts was evaluated using a vapor mercury lamp (150 W) for decomposition of methylene blue. The results of the photocatalytic activity variation showed that the photocatalytic activity of all the synthesized photocatalysts increases by increasing the UV irradiation time (in the range of 5 min to 20 min) and weight fraction of photocatalysts (pH = 4, pH = 8, pH = 12). The pH of suspension had negative effect on photocatalytic activity. The least and most photocatalytic activity belonged to the synthesized anatase-rutile titania and A-R-S#2, respectively. Increasing the amount of tin dioxide nanoparticles on the surface of titania leads to the enhancement of photocatalytic activity. The results of the analysis of variance showed that all the main factors and their binary and triple interactions significantly affect photocatalytic activity.

The Effect of Zeolite Composition and Grain Size on Gas Sensing Properties of SnO2/Zeolite Sensor.

In order to improve the sensing properties of tin dioxide gas sensor, four kinds of different SiO2/Al2O3 ratio, different particle size of MFI type zeolites (ZSM-5) were coated on the SnO2 to prepared zeolite modified gas sensors, and the gas sensing properties were tested. The measurement results showed that the response values of ZSM-5 zeolite (SiO2/Al2O3 = 70, grain size 300 nm) coated SnO2 gas sensors to formaldehyde vapor were increased, and the response to acetone decreased compared with that of SnO2 gas sensor, indicating an improved selectivity property. The other three ZSM-5 zeolites with SiO2/Al2O3 70, 150 and 470, respectively, and grain sizes all around 1 µm coated SnO2 sensors did not show much difference with SnO2 sensor for the response properties to both formaldehyde and acetone. The sensing mechanism of ZSM-5 modified sensors was briefly analyzed.

High Volumetric Capacity of Hollow Structured SnO2@Si Nanospheres for Lithium-Ion Batteries.

A novel design of hollow structured SnO2@Si nanospheres was presented, which not only demonstrates high volumetric capacity as anode of LIBs, but also prevents aggregation of Sn and confines solid electrolyte interphase thickening. An impressive volumetric specific capacity of 1030 mAh cm-3 was maintained after 500 cycles. The electrochemical impedance spectroscopy and differential scanning calorimetry indicated that solid electrolyte interphase can be confined in pores of as-prepared hollow structured SnO2@Si.

Evaluating the cytotoxicity of tin dioxide nanofibers.

Tin dioxide nanofibers (SnDNFs) are small fibers that have many applications. Tin dioxide nanofibers can be used in cosmetics, solar cells, toxic gas release sensors, and air pollution control. To date there have been few studies on the cytotoxicity of SnDNFs. The goal of this research is to determine if electrospun SnDNFs are toxic in a lung cancer cell line (A549). Considering the nano-scale size of the fibers, they can easily be inhaled and enter the pulmonary system and cause toxic effects in the lung. Occupational exposure to SnDNFs has been linked to pulmonary disease, making the A549 cell line important in this study. Nanofiber toxicity can vary based upon the characteristics of the fibers. Smaller nanofibers have been shown to have more toxic effects than their larger counterparts. The synthesized SnDNFs were characterized using SEM, Raman spectroscopy, and powder X-ray diffractometer (PXRD). SEM images showed the fibers to be 200-300 nm in diameter. Raman spectroscopy and PXRD indicated that the fibers were in the rutile phase. After quantifying the SnDNFs, the fibers were introduced to A549 cells at concentrations ranging from 0.02-500 µg mL-1 and incubated at 37°C. These cells were quantified with the MTT assay to measure cell proliferation (IC50 = 0.02 mg mL-1), while lactate dehydrogenase (LDH) leakage was used to determine cytotoxicity, and apoptosis assays to assess the mechanism of cell death. Increasing concentration of SnDNF generated a consequential decrease in cell proliferation and viability. The percent cytotoxicity of SnDNF was not significantly changed at the various concentrations and time frames. In order to gain additional insight about the mechanism of cytotoxicity of SnDNFs, genes with links to inflammation and apoptosis were evaluated and found to be over-expressed in treated cells. At the concentrations of SnDNF examined, SnDNF was mildly toxic to the A549 cells.

SnO2 Quantum Dots@Graphene Oxide as a High-Rate and Long-Life Anode Material for Lithium-Ion Batteries.

Tin-based electrode s offer high theoretical capacities in lithium ion batteries, but further commercialization is strongly hindered by the poor cycling stability. An in situ reduction method is developed to synthesize SnO2 quantum dots@graphene oxide. This approach is achieved by the oxidation of Sn(2+) and the reduction of the graphene oxide. At 2 A g(-1), a capacity retention of 86% is obtained even after 2000 cycles.