Fungal formation of selenium and tellurium nanoparticles.

The fungi Aureobasidium pullulans, Mortierella humilis, Trichoderma harzianum and Phoma glomerata were used to investigate the formation of selenium- and tellurium-containing nanoparticles during growth on selenium- and tellurium-containing media. Most organisms were able to grow on both selenium- and tellurium-containing media at concentrations of 1 mM resulting in extensive precipitation of elemental selenium and tellurium on fungal surfaces as observed by the red and black colour changes. Red or black deposits were confirmed as elemental selenium and tellurium, respectively. Selenium oxide and tellurium oxide were also found after growth of Trichoderma harzianum with 1 mM selenite and tellurite as well as the formation of elemental selenium and tellurium. The hyphal matrix provided nucleation sites for metalloid deposition with extracellular protein and extracellular polymeric substances localizing the resultant Se or Te nanoparticles. These findings are relevant to remedial treatments for selenium and tellurium and to novel approaches for selenium and tellurium biorecovery.

Ammonium Fluoride Passivation of CdZnTeSe Sensors for Applications in Nuclear Detection and Medical Imaging.

Cadmium zinc telluride selenide (Cd1-xZnxTe1-ySey or CZTS) is one of the emerging CdTe-based semiconductor materials for detecting X- and gamma-ray radiation at or near room temperature (i.e., without cryogenic cooling). Potential applications of CZTS sensors include medical imaging, X-ray detection, and gamma-ray spectroscopy. Chemical passivation of CZTS is needed to reduce the conductivity of Te-rich surfaces, which reduces the noise and improves the device performance. In this study, we focus on the effect of surface passivation of CZTS using a 10% aqueous solution of ammonium fluoride. The effects of the chemical treatment were studied on the leakage current, charge transport measured as the electron mobility-lifetime (µτ) product, and the spectral resolution measured as the full-width at half-maximum (FWHM) of specific peaks. After passivation, the leakage current increased and began to decrease towards pre-passivation levels. The energy resolutions were recorded for eight applied voltages between -35 V and -200 V. The results showed an average of 25% improvement in the detector's energy resolution for the 59.6 keV gamma peak of Am-241. The electron µτ product was unchanged at 2 × 10-3 cm2/V. These results show that ammonium fluoride is effective for chemical passivation of CZTS detectors.

In situ detection of salicylic acid binding sites in plant tissues.

The determination of hormone-binding sites in plants is essential in understanding the mechanisms behind hormone function. Salicylic acid (SA) is an important plant hormone that regulates responses to biotic and abiotic stresses. In order to label SA-binding sites in plant tissues, a quantum dots (QDs) probe functionalized with a SA moiety was successfully synthesized by coupling CdSe QDs capped with 3-mercaptopropionic acid (MPA) to 4-amino-2-hydroxybenzoic acid (PAS), using 1-ethyl-3-(3-dimethyllaminopropyl) carbodiimide (EDC) as the coupling agent. The probe was then characterized by dynamic light scattering and transmission electron microscopy, as well as UV/vis and fluorescence spectrophotometry. The results confirmed the successful conjugation of PAS to CdSe QDs and revealed that the conjugates maintained the properties of the original QDs, with small core diameters and adequate dispersal in solution. The PAS-CdSe QDs were used to detect SA-binding sites in mung bean and Arabidopsis thaliana seedlings in vitro and in vivo. The PAS-CdSe QDs were effectively transported into plant tissues and specifically bound to SA receptors in vivo. In addition, the effects of the PAS-CdSe QDs on cytosolic Ca(2+) levels in the tips of A. thaliana seedlings were investigated. Both SA and PAS-CdSe QDs had similar effects on the trend in cytosolic-free Ca(2+) concentrations, suggesting that the PAS-CdSe QDs maintained the bioactivity of SA. To summarize, PAS-CdSe QDs have high potential as a fluorescent probe for the in vitro/in vivo labeling and imaging of SA receptors in plants.

Biosynthesis of CdS nanoparticles in banana peel extract.

Cadmium sulfide (CdS) nanoparticles (NPs) were synthesized by using banana peel extract as a convenient, non-toxic, eco-friendly 'green' capping agent. Cadmium nitrate and sodium sulfide are main reagents. A variety of CdS NPs are prepared through changing reaction conditions (banana extracts, the amount of banana peel extract, solution pH, concentration and reactive temperature). The prepared CdS colloid displays strong fluorescence spectrum. X-ray diffraction analysis demonstrates the successful formation of CdS NPs. Fourier transform infra-red (FTIR) spectrogram indicates the involvement of carboxyl, amine and hydroxyl groups in the formation of CdS NPs. Transmission electron microscope (TEM) result reveals that the average size of the NPs is around 1.48 nm.

Isolation, purification and characterisation of selenium-containing polysaccharides and proteins in selenium-enriched Radix puerariae.

BACKGROUND: Selenium (Se) is an essential dietary mineral and Radix puerariae (RP) (the dried root of Pueraria lobata Willd.) is a botanical supplement widely used as a nutraceutical. Food enriched with Se provides a feasible and economic approach for production of organic Se compounds. However, little is known about Se-enriched RP and the structure of Se-containing polysaccharides and proteins derived from Se-enriched RP. RESULTS: The organic form of Se accounted for 82.42% of total content. Purification by DEAE-52 and Sephadex G-100 column chromatography yielded three single fractions--RP-SeP-11, RP-SeP-22 and RP-SeP-33--with Se contents of 0.9562 × 10⁻³, 0.6113 × 10⁻³ and 0.3827 × 10⁻³ g kg⁻¹, respectively. RP-SeP-11 (3.5 kDa) was made of glucose, RP-SeP-22 (19.6 kDa) was composed of xylose and glucose, and RP-SeP-33 (97.9 kDa) was made up galactose, mannose and glucose. Two Se-containing proteins were obtained with Se content of 3.175 × 10⁻³ and 4.328 × 10⁻³ g kg⁻¹, respectively. One appeared as three subunits with molecular masses of 43.0, 29.0 and 17.8 kDa while the other appeared as two subunits with molecular masses of 43.0 and 26.3 kDa. CONCLUSION: The results provide a basis for promoting the utilisation of RP resources enriched with Se as a promising tool for the food industry and are significant for its contribution to Se biochemistry in plants.

Cysteine-specific PEGylation of rhG-CSF via selenylsulfide bond.

A new PEGylation reagent enabling selective modification of free thiol groups is described in this article. The reagent was synthesized by attaching linear polyethylene glycol (PEG) N-hydroxysuccinimide to selenocystamine. The reaction was very fast, resulting in over 95% conversion yield. The active group of this new PEG-Se reagent is a diselenide, reacting with thiols via thiol/diselenide exchange reaction. Recombinant human granulocyte colony-stimulating factor (rhG-CSF) with an unpaired cysteine at the position 18 (Cys18) was used as a model protein. It was comparatively PEGylated with the new PEG-Se reagent, as well as with commercially available maleimide (PEG-Mal) and ortho-pyridyl disulfide (PEG-OPSS) PEG reagents. The highest PEGylation yield was obtained with PEG-Mal, followed by PEG-OPSS and PEG-Se. The reaction rates of PEG-Mal and PEG-Se were comparable, while the reaction rate of PEG-OPSS was lower. Purified monoPEGylated rhG-CSF conjugates were characterized and compared. Differences in activity, stability, and in vivo performance were observed, although all conjugates contained a 20 kDa PEG attached to the Cys18. Minor conformational changes were observed in the conjugate prepared with PEG-Mal. These changes were also reflected in low in vitro biological activity and aggregate formation of the maleimide conjugate. The conjugate prepared with PEG-Se had the highest in vitro biological activity, while the conjugate prepared with PEG-OPSS had the best in vivo performance.

Selenide retention by mackinawite.

The isotope (79)Se may be of great concern with regard to the safe disposal of nuclear wastes in deep geological repositories due to its long half-life and potential mobility in the geosphere. The Se mobility is controlled by the oxidation state: the oxidized species (Se(IV)) and (Se(VI)) are highly mobile, whereas the reduced species (Se(0) and Se(-II)) form low soluble solids. The mobility of this trace pollutant can be greatly reduced by interacting with the various barriers of the repository. Numerous studies report on the oxidized species retention by mineral phases, but only very scarce studies report on the selenide (Se(-II)) retention. In the present study, the selenide retention by coprecipitation with and by adsorption on mackinawite (FeS) was investigated. XRD and SEM analyses of the samples reveal no significant influence of Se on the mackinawite precipitate morphology and structure. Samples from coprecipitation and from adsorption are characterized at the molecular scale by a multi-edge X-ray absorption spectroscopy (XAS) investigation. In the coprecipitation experiment, all elements (S, Fe, and Se) are in a low ionic oxidation state and the EXAFS data strongly point to selenium located in a mackinawite-like sulfide environment. By contacting selenide ions with FeS in suspension, part of Se is located in an environment similar to that found in the coprecipitation experiment. The explanation is a dynamical dissolution-recrystallization mechanism of the highly reactive mackinawite. This is the first experimental study to report on selenide incorporation in iron monosulfide by a multi-edge XAS approach.

Characterization of selenium species in extract from Niboshi (a processed Japanese anchovy).

Fish are selenium rich foodstuffs and a major selenium source for the Japanese population. Niboshi is processed from Japanese anchovy (Engraulis japonicus) and commonly used to prepare soup stock for Japanese dishes. In this study, we characterized selenium species in the Niboshi extract by ultrafiltration, ion-exchange chromatography and mass spectrometry. Selenium species in the Niboshi were more extractable by polar solvents (water and ethanol) than an apolar one (hexane) along with amino acids and proteinous species. Selenium in the water-extract from the Niboshi was mostly ascribed to organoselenium compounds with a molecular mass less than 5 kDa. Although selenoamino acids and selenoproteins and their fragments were involved in the extract, a large portion of the selenium species appeared to be low-molecular-mass organoselenium compounds other than selenoamino acids and their derivatives. Ion-exchange chromatographic separations revealed that most of the selenium species in the extract possess anionic and/or amphoteric characteristics. One of these selenium species from the Niboshi extract was detected at m/z 577 for 80Se by mass spectrometry subsequent to ion-pair extraction.

Effect of pH on nitrate and selenate reduction in flue gas desulfurization brine using the H2-based membrane biofilm reactor (MBfR).

Increased tightening of air regulations is leading more electric utilities to install flue gas desulfurization (FGD) systems. These systems produce brine containing high concentrations of nitrate, nitrite, and selenate which must be removed before discharge. The H2-based membrane biofilm reactor (MBfR) was shown to consistently remove nitrate, nitrite, and selenate at high efficiencies. The maximum selenate removal flux reached 362 mgSe m(-2)d(-1) and was higher than that observed in earlier research, which shows continual improvement of the biofilm for selenate reduction. A low pH of 6.8 inhibited precipitation when treating actual FGD brine, yet did not inhibit removal. SO4(2-) was not removed and therefore did not compete with nitrate, nitrite, and selenate reduction for the available H2.

Effects of seleno-Sesbania canabina galactomannan on anti-oxidative and immune function of macrophage.

Seleno-polysaccharides have become a major topic for research owing to their high anti-oxidative capacity and immune-enhancing activities. In this study, galactomannan (GM) was isolated from Sesbania cannabina, and next modified using HNO3-Na2SeO3 method to obtain six varieties of seleno-galactomannans (SeGMs). FT-IR and GPC results showed the changes in chemical structure of SeGMs, indicating successful combination of selenium and GM. By measuring superoxide dismutase and malondialdehyde, the SeGMs showed a stronger protective effect against H2O2-induced oxidative damage in vitro than unmodified GM using macrophage RAW264.7 cell as a model, and the effect of SeGMs-14 was prominent. However, the selenylation modification did not show any obvious effect on the immunomodulatory activity of GM, as determined by the index of tumor necrosis factor-α, interleukin-6, and interleukin-1ß. Overall, the prepared SeGMs from galactomannan could potentially serve as a dietary supplement of Se or an organic antioxidant.

Chemical control of the photoluminescence of CdSe quantum dot-organic complexes with a series of para-substituted aniline ligands.

Replacement of the native (as-synthesized) ligands of colloidal CdSe QDs with varying concentrations of a series of para-substituted anilines (R-An), where R ranges from strongly electron-withdrawing to strongly electron-donating, decreases the PL of the QDs. The molar ratio of R-An to QD ([R-An]:[QD]) at which the PL decreases by 50% shifts by 4 orders of magnitude over the series R-An. The model employed to describe the data combines a Freundlich binding isotherm (which reflects the dependence of the binding affinity of the amine headgroups of R-An on the substituent R) with a function that describes the response of the PL to R-An ligands once they are bound at their equilibrium surface coverage. The latter function includes as a parameter the rate constant, k(nr), for nonradiative decay of the exciton at a site to which an R-An ligand is coordinated. The value of this parameter reveals that the predominant mechanism of QD-ligand interaction is passivation of Cd(2+) surface sites through sigma-donation for R-An ligands with R = H, Br, OCF(3), and reductive quenching through photoinduced hole transfer for R = MeO, (Me)(2)N.

Selenate removal in methanogenic and sulfate-reducing upflow anaerobic sludge bed reactors.

This paper evaluates the use of upflow anaerobic sludge bed (UASB) bioreactors (30 degrees C, pH=7.0) to remove selenium oxyanions from contaminated waters (790 microg Se L(-1)) under methanogenic and sulfate-reducing conditions using lactate as electron donor. One UASB reactor received sulfate at different sulfate to selenate ratios, while another UASB was operated under methanogenic conditions for 132 days without sulfate in the influent. The selenate effluent concentrations in the sulfate-reducing and methanogenic reactor were 24 and 8 microg Se L(-1), corresponding to removal efficiencies of 97% and 99%, respectively. X-ray diffraction (XRD) analysis and sequential extractions showed that selenium was mainly retained as elemental selenium in the biomass. However, the total dissolved selenium effluent concentrations amounted to 73 and 80 microg Se L(-1), respectively, suggesting that selenate was partly converted to another selenium compound, most likely colloidally dispersed Se(0) nanoparticles. Possible intermediates of selenium reduction (selenite, dimethylselenide, dimethyldiselenide, H(2)Se) could not be detected. Sulfate reducers removed selenate at molar excess of sulfate to selenate (up to a factor of 2600) and elevated dissolved sulfide concentrations (up to 168 mg L(-1)), but selenium removal efficiencies were limited by the applied sulfate-loading rate. In the methanogenic bioreactor, selenate and dissolved selenium removal were independent of the sulfate load, but inhibited by sulfide (101 mg L(-1)). The selenium removal efficiency of the methanogenic UASB abruptly improved after 58 days of operation, suggesting that a specialized selenium-converting population developed in the reactor. This paper demonstrates that both sulfate-reducing and methanogenic UASB reactors can be applied to remove selenate from contaminated natural waters and anthropogenic waste streams, e.g. agricultural drainage waters, acid mine drainage and flue gas desulfurization bleeds.

Highly sensitive electrochemical biosensor for streptavidin detection based on CdSe quantum dots.

An electrochemical biosensor was developed based on a steric hindrance hybridization assay to allow the highly sensitive detection of streptavidin. In the steric hindrance hybridization assay, the signaling strand DNA (sig-DNA) was labeled at the 3' end with CdSe quantum dots (QDs) and at the 5' end with biotin, and capturing strand DNA (the complementary strand of sig-DNA) was labeled at the 5' end with thiol. The steric hindrance effect generated by streptavidin which was bound with the signaling DNA strand. The streptavidin limited the ability of the sig-DNA to hybridize with the cap-DNA, which were linked on the surface of a gold electrode. Therefore, the concentration of streptavidin was detected indirectly based on the concentration of CdSe QDs on the electrode surface. The concentration of CdSe QDs on the electrode surface was detected by differential pulse anodic stripping voltammetry. Under optimal conditions, the streptavidin detection range using the as-prepared biosensor was 1.96pg/mL to 1.96µg/mL and the detection limit was 0.65pg/mL. The experimental results showed that the electrochemical biosensor could detect streptavidin rapidly and accurately.

Separation of selenium, zinc, and copper compounds in bovine whey using size exclusion chromatography linked to inductively coupled plasma mass spectrometry.

To study the role of trace elements for the quality and nutritional value of bovine milk, the distribution of selenium, zinc, and copper in whey was investigated using a method linking size exclusion chromatography to inductively coupled plasma mass spectrometry (SEC-ICP-MS). Three major peaks were detected for selenium, two peaks for zinc, and five peaks for copper. More than 65% of the selenium was found in protein fractions, mainly in fractions coinciding with the major whey proteins beta-lactoglobulin and alpha-lactalbumin. All zinc was associated with low molecular weight compounds (<5 kDa) and one of these compounds was probably citrate. More than 60% of the copper eluted in protein fractions and two of the five major peaks probably contained metallothionein and citrate. This method was used to compare milk and whey produced by organic and conventional feeding procedures. The selenium content in whey and desalted milk produced using organic regimens was significantly lower than that in conventional samples. Moreover, the proportion of selenium in protein fractions of organic whey was significantly smaller than that in conventional whey, but the distributions of zinc and copper did not differ. This study showed that with the SEC-ICP-MS technique the distribution profiles of several trace elements in whey could be studied in the same run and that the selenium profile differed in whey produced by organic and conventional procedures.

Speciation of selenium in a commercial dietary supplement by liquid chromatography coupled with inductively coupled plasma-mass spectrometry (ICP-MS).

Size exclusion and anion-exchange chromatographies coupled with inductively coupled plasma-mass spectrometry (ICP-MS) were used for the speciation of selenium (Se) in a dietary supplement. A sequential extraction method resulted in 85% recovery of Se and 78% of the Se extracted could be identified. The results obtained show that selenomethionine and its oxide are the predominant compounds, while selenite and selenomethylcysteine are present at low concentrations. Methane seleninic acid, probably arising from the oxidation of selenomethylcysteine, accounted for 22% of total Se. High-molecular-weight compounds, probably proteins, were detected in sodium dodecyl sulfate (SDS) and driselase extracts by size exclusion chromatography.

Sorption-desorption of selenite and selenate on Mg-Al layered double hydroxide in competition with nitrate, sulfate and phosphate.

Selenate and selenite are considered emerging contaminants and pose a risk to living organisms. Since selenium anion species are at low concentration in aquatic environments, materials for its retention are required to enable monitoring. Herein, hydrotalcite was calcined and characterised to investigate sorption and desorption of selenite and selenate in competition with nitrate, sulfate and phosphate. Sorption experiments were carried out in batch system and desorption by sequential dilution. Selenite and selenate concentration remaining after N desorption steps was determined by mass balance. The isotherms were adjusted to the dual-mode Langmuir-Freundlich model (R2 > 0.99). Maximum sorption capacity ranged from 494 to 563 meq kg-1 for selenite and from 609 to 659 meq kg-1 for selenate. Sulfate and phosphate ions showed greater competitive effect on the sorption of selenate and selenite, respectively. Low mobilization factors and high sorption efficiency (MF<3%; SE ≈ 100%) indicated that calcined hydrotalcite has the wanted characteristics for retention of relevant selenium anion species in aqueous media.

Seleno-compounds in garlic and onion.

Garlic (Allium sativum) and onion (Allium cepa) are widely known for their biological properties but are far from having revealed all of their secrets even if the compounds involved in the biological mechanisms, flavenols, sulphur and seleno compounds have been identified. The beneficial effect of garlic on health including protection against cardiovascular diseases and cancers results from all of these compounds although their individual involvement is complex. Garlic and onion, broccoli, wild leek, have the ability to accumulate the selenium (Se) from soil. These Se-enriched plants present a greater protection against carcinogenesis than the common plants and two Se-compounds possessing anti-cancer activity have been identified: Se-methyl selenocysteine and gamma-glutamyl-Se-methyl selenocysteine. However, several Se-compounds from Se-enriched garlic or onion remain unidentified. The techniques for the detection of Se-species are numerous but few methods are able to identify the detected compounds. The very small quantities of Se-compounds present and the clear lack of standards do not make their analysis straightforward, particularly for non-enriched samples. Over the last 10 or so years development of the synthesis of Se-compounds and the use of GC-AED or EC/HPLC-ICP-MS have shown considerable possibilities. These techniques have allowed advances in the identification of Se-compounds, some of which are analogues of S-compounds in plants and yeasts. When these techniques are coupled to EC/HPLC-APCI-MS-MS, they provide a lot of information about the Se-biosynthesis in garlic. This has allowed the preferential formation of methylated compounds in Se-biochemistry to be identified, in contrast to the sulphur biochemistry of the Allium spp. in which compounds containing propenylic groups predominate. This review focuses on the recent advances in the analytical methods of Se-compounds in garlic and onion and particular attention is given to the biological properties of Se-species identified in Se-enriched plants.

Shake and break--shaking-induced changes of size quantization in aggregated quantum dots.

We show how simple mechanical agitation of precipitated CdSe quantum dot aggregates causes partially reversible color changes (clearly visible to the eye) in the absorption spectrum of the CdSe (about 4 nm size). The color changes, which are due to changes in size quantization, are not accompanied by change in quantum dot size. This phenomenon is explained by partial deaggregation of the precipitates, leading to reduced charge overlap between neighboring dots. Shaking was shown to result in a looser aggregate structure. It is suggested that CdSO3 particles (an initial product of the CdSe formation reaction) act as weak bridges between CdSe quantum dots, mediating the interparticle interactions and allowing the deaggregation to occur on shaking.

[Trends in chemical speciation of selenium in living organisms by hyphenated techniques].

In the environment and living organisms, limited concentrations and complexity of selenium compounds constitute challenges to the analytical techniques. Since their biological activities are dependent on their chemical states and structure, the key issue lies in the selective determination of the particular species of selenium, which is beneficial to clearly understanding its biochemical roles in metabolism, physiology, toxicology, nutrition, and clinical chemistry. For these purposes, the advanced analytical techniques are greatly indispensable. In the present paper, the current status and development trends in the speciation analysis of selenium by hyphenated techniques is selectively reviewed with the emphasis on the coupling of electrophoretic or chromatographic separation with atomic spectroscopy and mass spectrometry, which render element-selective detection and identification of selenium compounds.

[New approaches to selenium speciation].

A review of the recent developments in selenium speciation analysis was presented, focusing on the techniques of separation, interface, elemental specific detection and identification of selenium species; the methods of sample storage and pretreatment storage for selenium speciation were also introduced.