Microfluidic Chip-Based Wearable Colorimetric Sensor for Simple and Facile Detection of Sweat Glucose.

This study reports a microfluidic chip-based wearable colorimetric sensor for detecting sweat glucose. The device consisted of five microfluidic channels branching out from the center and connected to the detection microchambers. The microchannels could route the sweat excreted from the epidermis to the microchambers, and each of them was integrated with a check valve to avoid the risk of the backflow of the chemical reagents from the microchamber. The microchambers contained the pre-embedded glucose oxidase (GOD)-peroxidase-o-dianisidine reagents for sensing the glucose in sweat. It was found that the color change caused by the enzymatic oxidation of o-dianisidine could show a more sensitive response to the glucose than that of the conventional GOD-peroxidase-KI system. This sensor could perform five parallel detections at one time. The obtained linear range for sweat glucose was 0.1-0.5 mM with a limit of detection of 0.03 mM. The sensor was also used to detect the glucose in sweat samples from a group of subjects engaged in both fasting and postprandial trials. The results showed that our wearable colorimetric sensor can reveal the subtle differences existing in the sweat glucose concentration after the fasting and the oral glucose uptake.

Treatment of 3,3'-dimethoxybenzidine in sludge by advance oxidation process: Degradation products and toxicity evaluation.

Studies on the oxidation products of organic pollutants and their toxicity in textile dyeing sludge after the sludge was treated by the advance oxidation processes were limited, since textile dyeing sludge was a complicated mixture. For the first time, simulated sludge was used to study the degradation mechanism of 3,3'-dimethoxybenzidine (DMB) during the combined ultrasound-Mn(VII) treatment. The toxicity of DMB and its products was also evaluated. The results indicated that the compositions and microstructures of polyaluminium chloride (PAC)- and polyferric sulphate (PFS)-based simulated sludge were similar to those of real textile dyeing sludge. The optimum conditions of ultrasound-Mn(VII) treatment were: a KMnO4 dosage of 40 µM, an ultrasound power density of 0.36 W cm-3, and a reaction time of 20 min. 98.24% of DMB and 63.04% of total organic carbon (TOC) in the simulated sludge were removed. Six products, that is, 2-nitroanisole, 3-methoxy-4-nitrophenol, vanillylmandelic acid, vanillyl alcohol, m-anisic acid, and benzoic acid, were identified by GC-MS and LC-MS-MS. It was noted that all of these identified products were also detected in the real textile dyeing sludge after the ultrasound-Mn(VII) treatment. All of them were less toxic than DMB. Moreover, 53.30% and 54.80% of toxicity toward the alga Desmodesmus subspicatus and the bacterium Vibrio fischeri were removed in simulated sludge, respectively. Therefore, simulated sludge was helpful for studying a pollutant's degradation mechanism in the complex sludge mixtures. The results would also provide some useful suggestions for the sludge disposal after the sludge was treated by the advance oxidation processes.

Fabrication, characterization and application of laccase-nylon 6,6/Fe3+ composite nanofibrous membrane for 3,3'-dimethoxybenzidine detoxification.

In this study, laccase was immobilized on nylon 6,6/Fe3+ composite (NFC) nanofibrous membrane and used for the detoxification of 3,3'-dimethoxybenzidine (DMOB). The average size and tensile strength of the NFC membrane were found to be 60-80 nm (diameter) and 2.70 MPa, respectively. The FTIR results confirm that the amine (N-H) group of laccase was attached with Fe3+ particles and the carbonyl (C=O) group of NFC membrane via hydrogen bonding. The half-life of the laccase-NFC membrane storage stability was increased from 6 to 11 weeks and the reusability was significantly extended up to 43 cycles against ABTS oxidation. Enhanced electro-oxidation of DMOB by laccase was observed at 0.33 V and the catalytic current was found to be 30 µA. The DMOB-treated mouse fibroblast 3T3-L1 preadipocytes showed maximum (97 %) cell inhibition at 75 µM L-1 within 24 h. The cytotoxicity of DMOB was significantly decreased to 78 % after laccase treatment. This study suggests that laccase-NFC membrane might be a good candidate for emerging pollutant detoxification.

Continuous colorimetric screening assay for detection of d-amino acid aminotransferase mutants displaying altered substrate specificity.

D-Amino acid aminotransferase (DAAT) catalyzes the synthesis of numerous d-amino acids, making it an attractive biocatalyst for the production of enantiopure d-amino acids. To bolster its biocatalytic applicability, improved variants displaying increased activity toward non-native substrates are desired. Here, we report the development of a high-throughput, colorimetric, continuous coupled enzyme assay for the screening of DAAT mutant libraries that is based on the use of d-amino acid oxidase (DAAO). In this assay, the d-amino acid product of DAAT is oxidized by DAAO with concomitant release of hydrogen peroxide, which is detected colorimetrically by the addition of horseradish peroxidase and o-dianisidine. Using this assay, we measured apparent KM and kcat values for DAAT and identified mutants displaying altered substrate specificity via the screening of cell lysates in 96-well plates. The DAAO coupled assay is sensitive in that it allowed the detection of a DAAT mutant displaying an approximately 2000-fold decrease in kcat/KM relative to wild type. In addition, the DAAO assay enabled the identification of two DAAT mutants (V33Y and V33G) that are more efficient than wild type at transaminating the non-native acceptor phenylpyruvate. We expect that this assay will be useful for the engineering of additional mutants displaying increased activity toward non-native substrates.

Automation of o-dianisidine assay for ceruloplasmin activity analyses: usefulness of investigation in Wilson's disease and in hepatic encephalopathy.

Ceruloplasmin (Cp) is a serum ferroxidase that plays an essential role in iron metabolism. It is routinely tested by immunoturbidimetric assays that quantify the concentration of the protein both in its active and inactive forms. Cp activity is generally analyzed manually; the process is time-consuming, has a limited repeatability, and is not suitable for a clinical setting. To overcome these inconveniences, we have set the automation of the o-dianisidine Cp activity assay on a Cobas Mira Plus apparatus. The automation was rapid and repeatable, and the data were provided in terms of IU/L. The assay was adapted for human sera and showed a good precision [coefficient of variation (CV) 3.7 %] and low limit of detection (LoD 11.58 IU/L). The simultaneous analysis of Cp concentration and activity in the same run allowed us to calculate the Cp-specific activity that provides a better index of the overall Cp status. To test the usefulness of this automation, we tested this assay on 104 healthy volunteers and 36 patients with Wilson's disease, hepatic encephalopathy, and chronic liver disease. Cp activity and specific activity distinguished better patients between groups with respect to Cp concentration alone, and providing support for the clinical investigation of neurological diseases in which liver failure is one of the clinical hallmarks.

"Ready-to-use" hollow nanofiber membrane-based glucose testing strips.

A novel "ready-to-use" glucose test strip based on a polyurethane hollow nanofiber membrane was fabricated through facile co-axial electrospinning. By utilizing glucose oxidase and horseradish peroxidase in the core-phase solution, and a chromogenic agent either in the core solution (in which case 2,2'-azinobis-(3-ethylbenzthiazoline-6-sulphonate) (ABTS) was used) or in the shell-phase solution (in which case o-dianisidine was used) for co-axial electrospinning, in situ co-encapsulation of the two enzymes within the hollow nano-chamber and incorporation of chromogenic agents either inside the nano-chamber or in the shell of the hollow nanofibers was realized. Such unique "all-in-one" feature enabled the prepared hollow nanofiber membrane-based test strips to be applied either as colorimetric sensors in solution or as an optical biosensor operated in the "dip-and-read" mode. When used as a colorimetric biosensor in solution, the test strip with o-dianisidine as chromogenic agent shows an excellent linear response range between 0.01 mM to 20 mM and a high apparent lumped activity recovery of 62.1% as compared to the reaction rate of the free bi-enzyme system. While the activity recovery of the test strip with ABTS as chromogenic agent is only 18.0%, and the test strip is found to be unstable due to spontaneous-oxidation of the ABTS. The o-dianisidine test strip was also applied as an optical biosensor, visible rufous color was quickly developed on the surface of the membrane upon dropping 10 µL of glucose sample, and an excellent correlation between differential diffusive reflectance of the test strip at 440 nm and glucose concentration was obtained in the range of 0.5-50 mM. The test strips also exhibited excellent long-term storage stability with a half-life at 25 °C as long as four months.

Measurement of plasma hemoglobin peroxidase activity.

We described a spectrophotometric method for measuring hemoglobin peroxidase activity in human plasma using o-dianisidine (o-DA) as the substrate and myeloperoxidase specific inhibitor 4-aminobensoic acid hydrazide (ruling out the probable contribution of myeloperoxidase to the measured parameter value). The optimal conditions (pH 5.5; 2 mM H2O2) have been determined, at which hemoglobin makes the main contribution to plasma oxidation of o-DA. A significant positive correlation between hemoglobin peroxidase activity measured by the spectrophotometric method and hemoglobin level measured by the pyridine hemochromogenic method has been detected (r=0.624; p<0.01) in plasma specimens from 16 donors. Plasma hemoglobin peroxidase activities were measured in healthy individuals and patients with type 2 diabetes mellitus and coronary heart disease. High plasma hemoglobin peroxidase activities in both groups of patients indicates disorders in the mechanisms of clearance of hemoglobin and its highly reactive derivatives and can serve as specific markers of diseases associated with oxidative stress.

Visualizing indoor ozone exposures via o-dianisidine based colorimetric passive sampler.

In this study, we developed a colorimetric ozone passive sampler (OPS) incorporating o-dianisidine, a redox dye, into a polydimethylsiloxane sheet. The reaction between ozone (O3) and o-dianisidine result in a visible yellowish color change. Unlike previous passive methods that rely on nitrate extraction or the color disappearance of indigotrisulfonate, the OPS offered improved recognition of average O3 exposure. To optimize OPS based on time-weighted average (TWA), we extracted and quantified the amount of reacted o-dianisidine after exposing OPS to O3 by varying concentrations (0-200 ppb) within 8 h. Colorimetric changes of OPS were further analyzed by capturing images, and the effective absorbance of blue scale showed the best fit (EAB, R2 =0.997). OPS validation on visual detection assessed by six parameters: limit of detection, limit of quantification, reproducibility, sampling rate, selectivity to interfering gases, and sensitivity to environmental factors. To enhance visibility, the OPS was assembled with coloration exposure guidelines, and a smartphone app was developed to quantify average O3 exposures. We further conducted field tests that showed the significant disparity between O3 concentrations and personal O3 exposures, which is considered more crucial for assessing health risks. The OPS was optimized to monitor O3 exposure levels and raise awareness among workers and occupants regarding invisible indoor hazards.

Influence of smoking on interleukin-1beta level, oxidant status and antioxidant status in gingival crevicular fluid from chronic periodontitis patients before and after periodontal treatment.

BACKGROUND AND OBJECTIVE: The aim of this study was to evaluate the impact of smoking on the relationship between interleukin-1 (IL-1ß) and oxidation in patients with periodontitis and response to nonsurgical periodontal therapy. MATERIAL AND METHODS: Data were obtained from 30 patients with generalized chronic periodontitis (15 smokers and 15 nonsmokers) and from 10 periodontally healthy controls. IL-1ß level, total oxidant status (TOS) and total antioxidant status (TAS) were recorded in gingival crevicular fluid. Probing depth, clinical attachment level, gingival and plaque indices and bleeding on probing were also measured. The gingival crevicular fluid and clinical parameters were recorded at baseline and 6 wk after periodontal treatment. RESULTS: The study showed statistically significant improvement of clinical parameters in both smokers and nonsmokers after periodontal treatment. Moreover, the baseline IL-1ß levels were significantly higher in smokers compared with nonsmokers (p < 0.05). After periodontal treatment, the IL-1ß levels were significantly reduced in both smokers and nonsmokers (p < 0.05). There were no significant differences in TOS and TAS between periodontitis patients and healthy controls at baseline and 6 wk after periodontal treatment. The level of IL-1ß in gingival crevicular fluid was positively correlated with TOS in both smokers and nonsmokers. CONCLUSIONS: Periodontal treatment improved the clinical parameters in both smokers and nonsmokers. The results confirm that periodontal therapy has an effect on IL-1ß levels in gingival crevicular fluid, but not on TOS and TAS.

Combining the physical adsorption approach and the covalent attachment method to prepare a bifunctional bioreactor.

Aminopropyl-functionalized SBA-15 mesoporous silica was used as a support to adsorb myoglobin. Then, in order to avoid the leakage of adsorbed myoglobin, lysozyme was covalently tethered to the internal and external surface of the mesoporous silica with glutaraldehyde as the coupling agent. The property of amino-functionalized mesoporous silica was characterized by N(2) adsorption-desorption and thermogravimetric (TG) analysis. The feature of the silica-based matrix before and after myoglobin adsorption was identified by fourier transform infrared (FTIR) and UV/VIS measurement. With o-dianisidine and H(2)O(2) as the substrate, the peroxidase activity of adsorbed myoglobin was determined. With Micrococus lysodeilicus as the substrate, the antibacterial activity of covalently tethered lysozyme was measured. Results demonstrated that the final product not only presented peroxidase activity of the myoglobin but yielded antibacterial activity of the lysozyme.

Non-linear effects of macromolecular crowding on enzymatic activity of multi-copper oxidase.

Enzymes catalyze biochemical reactions in highly crowded environments where the amount of macromolecules may occupy up to 40% of the volume. Here we report how cell-like conditions tune catalytic parameters for the monomeric multi-copper oxidase, Saccharomyces cerevisiae Fet3p, in vitro. At low amounts of crowding agent, we detect increases in both of K(M) (weaker substrate binding) and k(cat) (improved catalytic efficiency), whereas at higher crowding levels, both parameters were reduced. Presence of crowding agents does not affect Fet3p structural content but increases thermal resistance. The observations are compatible with ordering of a non-optimal substrate-binding site and restricted internal dynamics as a result of excluded volume effects making the protein less structurally 'strained'.

Amplified detection of microRNA based on ruthenium oxide nanoparticle-initiated deposition of an insulating film.

A highly sensitive microRNA (miRNA) biosensor that employs ruthenium oxide nanoparticle (RuO(2) NP)-initiated polymerization of 3,3'-dimethoxybenzidine (DB) and miRNA-templated deposition of an insulating poly(3,3'-dimethoxybenzidine) (PDB) film is described in this work. The biosensor was made of a mixed monolayer of oligonucleotide capture probes (CPs) and 4-mercaptoaniline on a gold electrode. Following hybridization with a RuO(2) NP-tagged target miRNA, a mixture of DB/H(2)O(2) in pH 5.0 0.10 M acetate buffer was applied to the biosensor. The RuO(2) NPs serve as polymerization initiator/catalyst for the polymerization of DB. And the hybridized anionic miRNA strands and free CPs serve as templates, guiding the deposition of PDB. The amount of the deposited PDB and its insulating power directly correlated to the concentration of the target miRNA in solution. Electrochemical impedance spectroscopic tests showed that a linear charge-transfer resistance-concentration relationship from 6.0 fM to 2.0 pM was attained after 60 min of incubation in the DB/H(2)O(2) mixture. There was no cross-hybridization between pre-miRNA and mature miRNA and very little cross-hybridization among closely related miRNA family members even at single-base-mismatched levels. This impedance-based biosensor offers an attractive alternative for miRNA expression profiling and may enable the development of a portable multiplexing miRNA profiling system.

Euphorbia peroxidase catalyzes thiocyanate oxidation in two different ways, the distal calcium ion playing an essential role.

The oxidation of the pseudohalide thiocyanate (SCN(-)) by Euphorbia peroxidase, in the presence or absence of added calcium, is investigated. After incubation of the native enzyme with hydrogen peroxide, the formation of Compound I occurs and serves to catalyze the thiocyanate oxidation pathways. The addition of a stoichiometric amount of SCN(-) to Compound I leads to the native enzyme spectrum; this process clearly occurs via two electron transfers from pseudohalide to Compound I. In the presence of 10 mM calcium ions, the addition of a stoichiometric amount of SCN(-) to Compound I leads to the formation of Compound II that returns to the native enzyme after addition of a successive stoichiometric amount of SCN(-), indicating that the oxidation occurs via two consecutive one-electron transfer steps. Moreover, different reaction products can be detected when the enzyme-hydrogen peroxide-thiocyanate reaction is performed in the absence or presence of 10 mM Ca(2+) ions. The formation of hypothiocyanous acid is easy demonstrated in the absence of added calcium, whereas in the presence of this ion, CN(-) is formed as a reaction product that leads to the formation of an inactive species identified as the peroxidase-CN(-) complex. Thus, although monomeric, Euphorbia peroxidase is an allosteric enzyme, finely tuned by Ca(2+) ions. These ions either can enhance the catalytic efficiency of the enzyme toward some substrates or can regulate the ability of the enzyme to exploit different metabolic pathways toward the same substrate.

Optimization of media components for laccase production by litter dwelling fungal isolate Fusarium incarnatum LD-3.

Laccase production by solid state fermentation (SSF) using an indigenously isolated litter dwelling fungus Fusarium incarnatum LD-3 was optimized. Fourteen medium components were screened by the initial screening method of Plackett-Burman. Each of the components was screened on the basis of 'p' (probability value) which was above 95% confidence level. Ortho-dianisidine, thiamine HCl and CuSO(4) . 5 H(2)O were identified as significant components for laccase production. The Central Composite Design response surface methodology was then applied to further optimize the laccase production. The optimal concentration of these three medium components for higher laccase production were (g/l): CuSO(4) . 5 H(2)O, 0.01; thiamine HCl, 0.0136 and ortho-dianisidine, 0.388 mM served as an inducer. Wheat straw, 5.0 g was used as a solid substrate. Using this statistical optimization method the laccase production was found to increase from 40 U/g to 650 U/g of wheat straw, which was sixteen times higher than non optimized medium. This is the first report on statistical optimization of laccase production from Fusarium incarnatum LD-3.

Serum ceruloplasmin oxidase activity is a sensitive and highly specific diagnostic marker for Wilson's disease.

BACKGROUND/AIMS: A low serum ceruloplasmin concentration is considered diagnostic for Wilson's disease. We aimed to evaluate an enzymatic test for ceruloplasmin oxidase activity and to compare it with the routinely used immunological ceruloplasmin measurement. METHODS: Serum ceruloplasmin was measured enzymatically with o-dianisidine dihydrochloride as substrate and immunologically. 110 Wilson's disease patients, 52 healthy controls, and 51 patients with impaired liver function not due to Wilson's disease were analyzed. Assay performance was tested by receiver operating characteristic curve analysis, McNemar test, and Spearman's rank correlation. RESULTS: The greatest sum of sensitivity and specificity was seen for the enzymatic ceruloplasmin assay at a cut-off point of 55 U/L (93.6% and 100%, respectively) and for the immunologic assay at a cut-off point of 0.19 g/L (93.6% and 78.8%, respectively). For healthy controls, the differences in specificity between both assays were statistically significant (McNemar, p=0.02). When additionally including patients with impaired liver function into the control group the specificity declined to 84.5% for the enzymatic assay and to 68.9% for the immunologic assay. The correlation between the enzymatic and immunologic assay was high in healthy controls (r=0.94), but weaker in Wilson's disease patients (r=0.70) and patients with impaired liver function not due to Wilson's disease (r=0.65). CONCLUSIONS: For the enzymatic assay the best cut-off point for predicting Wilson's disease was estimated to be 55 U/L. Our data suggest that the enzymatic ceruloplasmin assay is superior to the immunologic assay in diagnosing Wilson's disease and should become the preferred method.

Development of new methodologies for on-line determination of the bromate ion in samples of water subjected to ozonation treatment.

The bromate ion has been identified as an inorganic disinfection by-product (DPB) in water subjected to purification treatment. Its presence arises from the application of oxidation processes to water containing bromide through the action of oxidant agents such as the ozone used in ozonation processes. This ion has been identified as a possible carcinogen by the U.S. Environmental Protection Agency, which recommends a maximum concentration of 10 microgL(-1). The literature reports a broad range of methods for the analysis of bromate in water, among which ion chromatography is the one most widely used, with different detection systems. However, most of the methods described to date require state-of-the-art technology and costly instrumentation, such that they are not readily adaptable to routine analyses. The present work reports a procedure for the spectrophotometric determination of bromate based on the bromination reaction of 3-3' dimethoxybenzidine, o-dianisidine (ODA). The reaction is based on the formation of Br2 in the presence of excess bromide and the later bromination of ODA, generating a product that absorbs at 450 nm. The procedure was set up with Flow Injection Analysis and allows the determination of the analyte in the 8 microg L(-1)-3.3 mg L(-1) range, with a detection limit of 6.0 microg L(-1) and relative standard deviations (n=12, [BrO3-]=8.0 and 30.0 microg L(-1)) of 4.8% and 2.9%, respectively. The determination rate was 10-11 samples/hour.

[New approaches to the measurement of the concentration and peroxidase activity of myeloperoxidase in human blood plasma].

A novel method for spectrometrical measurement of myeloperoxidase (MPO) activity in plasma with o-dianisidine (DA) as a substrate is proposed. We have determined the optimal conditions, including the pH and hydrogen peroxide concentration, under which MPO is the main contributor to DA oxidation in plasma. Specific MPO inhibitors, salicylhydroxamic acid or (4-aminobenzoyl)hydrazide, are added to measure the activity of other heme-containing peroxidases (mainly hemoglobin and its derivatives) and subtract their contribution from the total plasma peroxidase activity. Plasma MPO concentrations are quantified by a new enzyme-linked immunosorbent assay (ELISA) developed by us and based on the use of antibodies raised in rats and rabbits. The sensitivity of this ELISA is high: 0.2-250 ng/ml. A direct and significant (P < 0.0001) correlation was observed between the MPO activities measured spectrometrically and by ELISA in blood samples from 38 healthy donors. The proposed approaches to MPO measurement in plasma can be used to evaluate the enzyme activity and concentration, as well as the efficacy of mechanisms by which MPO is regulated under physiological conditions and against the background of various inflammatory diseases.

Hemozymes peroxidase activity of artificial hemoproteins constructed from the Streptomyces lividans xylanase A and iron(III)-carboxy-substituted porphyrins.

To develop artificial hemoproteins that could lead to new selective oxidation biocatalysts, a strategy based on the insertion of various iron-porphyrin cofactors into Xylanase A (Xln10A) was chosen. This protein has a globally positive charge and a wide enough active site to accommodate metalloporphyrins that possess negatively charged substituents such as microperoxidase 8 (MP8), iron(III)-tetra-alpha4-ortho-carboxyphenylporphyrin (Fe(ToCPP)), and iron(III)-tetra-para-carboxyphenylporphyrin (Fe(TpCPP)). Coordination chemistry of the iron atom and molecular modeling studies showed that only Fe(TpCPP) was able to insert deeply into Xln10A, with a KD value of about 0.5 microM. Accordingly, Fe(TpCPP)-Xln10A bound only one imidazole molecule, whereas Fe(TpCPP) free in solution was able to bind two, and the UV-visible spectrum of the Fe(TpCPP)-Xln10A-imidazole complex suggested the binding of an amino acid of the protein on the iron atom, trans to the imidazole. Fe(TpCPP)-Xln10A was found to have peroxidase activity, as it was able to catalyze the oxidation of typical peroxidase cosubstrates such as guaiacol and o-dianisidine by H2O2. With these two cosubstrates, the KM value measured with the Fe(TpCPP)-Xln10A complex was higher than those values observed with free Fe(TpCPP), probably because of the steric hindrance and the increased hydrophobicity caused by the protein around the iron atom of the porphyrin. The peroxidase activity was inhibited by imidazole, and a study of the pH dependence of the oxidation of o-dianisidine suggested that an amino acid with a pKA of around 7.5 was participating in the catalysis. Finally, a very interesting protective effect against oxidative degradation of the porphyrin was provided by the protein.

Caeruloplasmin oxidase activity: measurement in serum by use of o-dianisidine dihydrochloride on a microplate reader.

Background The enzymatic method of caeruloplasmin measurement is based on copper-dependent oxidase activity. The advantage of the oxidase determination is that it has a much lower detection limit compared with immunoassay-based methods. It has found its application in both the diagnosis of Wilson's disease and also in the monitoring of patients' response to treatment. Methods The method previously described in literature was adapted for use on a 96-well plate. Caeruloplasmin oxidase activity results were derived from the equation: caeruloplasmin oxidase activity = (A15-A5) × 185 U/L. Results Repeatability (intra-batch) imprecision ranged from 6 to 15% and intermediate (inter-batch) imprecision varied from 7 to 16% for caeruloplasmin oxidative activities of 14, 29, 45 and 99 U/L. Between 3 and 92 U/L, the assay appeared linear with a regression coefficient R2 = 0.9958. The lower limit of quantification was 4 U/L. Samples were stable over a five-week period at 4℃ and for at least four freeze-thaw cycles. There was a statistically significant difference between the areas under ROC curve for copper-to-caeruloplasmin ratios between caeruloplasmin oxidative activity and immunoassay-based methods ( P < 0.0171). The reference interval for caeruloplasmin activity was determined to be 12-166 U/L. Conclusions Using the oxidative assay provides a cost-effective means of estimating caeruloplasmin concentrations. The method is easily adaptable to a 96-well plate format that facilitates high throughput of samples in a busy laboratory. The enzymatic method is more sensitive and specific for differentiating between Wilson's and non-Wilson's when compared with immunoassay-based methods.

Improved analytical sensitivity reveals the occurrence of gender-related variability in diamine oxidase enzyme activity in healthy individuals.

OBJECTIVES: Serum diamine oxidase (DAO; EC 1.4.3.6) activity is often employed as a clinical indicator of the integrity of intestinal mucosa. However, interindividual variation in enzyme activity and reference values for healthy women and men have not been studied. DESIGN AND METHODS: DAO activity was measured by using cadaverine coupled to O-dianisidine oxidation in 50 healthy individuals. RESULTS: The mean activity was 7.59+/-3.67 U/L for women and 2.38+/-0.71 U/L for men (p<0.001). CONCLUSIONS: Gender is a major determinant for DAO activity in healthy subjects.