Effect of Water and Chlorhexidine with Different Pressures of Oral Irrigation Device on the Surface Roughness and Topography of Giomer

Abstract Objective: To evaluate the effect of different pressures of an oral irrigation device (OID) and the irrigation solution type on the surface roughness of the giomer restorative material. Material and Methods: In this in vitro study, disk-shaped giomer samples were fabricated and assigned to 5 groups (n=23): Group 1, storage in distilled water (control); Group 2, OID #7 pressure/ water; Group 3, OID #10 pressure/ water; Group 4, OID #7 pressure/ 0.05% CHX; Group 5, OID #10 pressure/ 0.05% CHX. The samples' treatment simulated a one-year application of OID. Surface roughness (Ra) and topography of the giomer were evaluated using profilometry and scanning electron microscopy. The data were analyzed with Paired t-test, Tukey, and ANOVA tests (α=0.05). Results: The Ra of the samples increased significantly after treatment with OID (p<0.001). The roughness increase in groups with a pressure of 10 was higher than those with a pressure of 7 (p<0.001). The effect of pressure on surface changes was significant (p<0.001). However, the solution type and the cumulative effect of these two factors were insignificant (p=0.08 and p=0.43, respectively). Conclusion: Oral irrigation device with both solutions significantly increased the surface roughness and topographic changes of the giomer. The severity of these changes was related to the device's pressure.

Does the combination of whitening toothpaste and hydrogen peroxide bleaching increase the surface roughness and change the morphology of a nanofilled composite?

Aim: To evaluate changes in the surface roughness and morphology of a nanofilled composite following toothbrushing with a whitening (WT) or regular toothpaste (RT), alone or combined with 35% hydrogen peroxide bleaching (HP). Methods: Seventy disc-shaped nanofilled composite (Filtek Z350XT) specimens were randomly divided into groups (n=10): WT, RT, TB (without toothpaste ­ control) or the combinations WT/ HP, RT/HP, TB/HP and HP. All groups underwent toothbrushing simulation (60,000 cycles) and bleaching treatment (4 sessions). Mean surface roughness (Ra, µm) was measured before (T0) and after treatments (TB). Surface morphology was assessed by scanning electron microscopy (SEM) at TB. Mean Ra was analyzed using general mixed models and multiple comparisons by the Tukey-Kramer test (α=5%). Results: HP caused no surface roughness changes on the nanofilled composite after treatment (p>0.05). RT toothbrushing, combined or not with HP, increased the surface roughness (p<0.05). WT and WT/ HP protocols had no effect on the surface roughness of the composite (p>0.05). The nanofilled composite submitted to RT toothbrushing combined with HP (RT/HP) presented substantial surface alterations under SEM, showing deep depressions and round-shaped defects. Toothbrushing with RT combined with the bleaching agent increased exposure of the inorganic fillers. Conclusion: WT toothbrushing, regardless of HP combination, or the single HP protocol had no effect on the surface roughness of the nanofilled composite. However, RT combined with HP negatively affected surface roughness and presented the most noticeable surface changes among groups

Color variation of composite resins in relation to the Vita Classical shade guide: colorimetric analysis

Aim: The aim of this study was to verify the color variation between different composite resins and the Vita Classical Shade Guide. Methods: Two-millimeter thickness samples were made (n = 6) from eight commercial brands of composite resin (shade A2): Charisma (Kulzer), Forma (Ultradent), Harmonize (Kerr), Luna (SDI), Opallis (FGM), Oppus Bulk Fill (FGM), Vittra (FGM) and Filtek Z250 XT (3M ESPE). Specimens were stored in distilled water for 7 days and then polished. Color measurements of samples and A2 shade of the Vita Classical Shade Guide were performed using the Vita Easy Shade Advance 4.0 spectrophotometer on a black background. Color variations were calculated using the CIEDE2000 formula, considering values ≥0.81 being noticeable by the human eye and ≥1.77 being clinically unacceptable. Results were statistically analyzed with a 5% significance level. Results: Color variation (ΔE) of composite (E1 ) compared to the Vita Classical Shade Guide (E0 ) was greater than clinically acceptable for all the materials evaluated in this study. Forma (ΔE=2.08 ± sd=0.47) and Filtek Z250 XT (2.50 ± 0.20) had the smallest amount of color variation values found in the results. Harmonize (3.32 ± 0.63) presented values similar to Filtek Z250 XT, but it was worse than Forma. Vittra (3.51 ± 0.28), Charisma (3.80 ± 0.20), Opallis (4.24 ± 0.30) and Luna (5.67 ± 0.20) did not differ among each other and presented higher color variation than Forma, Filtek Z350XT and Harmonize. Oppus Bulk Fill (13.94 ± 1.12) was the composite with the greatest color variation. Conclusions: The findings in this study show that attention should be taken when using the Vita Color Shade Guide for composite shade selection

Color and surface roughness alterations of bulk-fill resin composites submitted to simulated toothbrushing with whitening dentifrices

Aim: To evaluate the surface roughness and color stability of bulk-fill resin composites after simulated toothbrushing with whitening dentifrices. The radioactive/relative dentin abrasion (RDA) and radioactive/relative enamel abrasion (REA) of dentifrices were also assessed. Methods: Specimens (n=10) of Tetric N Ceram Bulk Fill (TNCB), Filtek One Bulk Fill (FOB) resin composites, and Z100(Control) were prepared using a cylindrical Teflon matrix. Surface roughness (Ra, µm) was assessed by a roughness meter and the color evaluations (ΔEab , ΔE00 , WID ) were performed using a digital spectrophotometer based on the CIELAB system. Three measurements were performed per sample, before and after simulated toothbrushing with 3D Oral-B White Perfection (3DW) and Black is White (BW) dentifrices. The abrasivity (REA and RDA values) of the used dentifrices was also determined by the Hefferren abrasivity test. Results: The Ra values increased significantly in all resin composites after 3DW and BW toothbrushing. The acceptable threshold color varied among resin composites, and TNCB and Z100 presented the highest ΔEab and ΔE00 for BW dentifrice. The 3DW dentifrice was significantly more abrasive than BW dentifrice on enamel and dentin. Conclusions: simulated toothbrushing with tested whitening dentifrices increased the surface roughness at acceptable levels. The Tetric N Ceram Bulk-fill and Z100 composite showed the highest color alteration in BW. 3D White Perfection dentifrice was more abrasive on dentin and enamel than Black is White.

Injectable Composite Resin Technique: An Alternative for Anterior Esthetic Restorations - Case Report / Técnica de Resina Compuesta Inyectable: Una Alternativa para Restauraciones Estéticas Anteriores - Reporte de Caso

This article aims to describe a clinical case of the use of the injectable restorative technique with composite resin in a patient with an esthetic complaint in the anterior teeth. Producing direct restorations in anterior teeth when performed with composite resin demands a long clinical time. Results often depend on the operator's ability to reproduce proper form, function, and esthetics. Lately, the versatility of composite resins has increased. As this material evolved, new techniques were introduced to simplify the restorative process and save time. The restorative technique with injectable fluid composite resin, in addition to delivering faster and with a certain ease, is capable of increasing the predictability of treatment results. However, it is known that flowable resins have lower wear resistance and color stability compared to conventional resins. Thus, a version of this material with a higher filler content in its composition was introduced to the market, to improve wear resistance and gloss retention. Long-term studies evaluating the use of low-viscosity resins are needed. The injectable technique can accurately reproduce the morphology obtained in the wax-up of the case, generating a satisfactory esthetic and functional result. Despite simplifying the fabrication of restorations when compared to the conventional technique, it is still necessary for the operator to have some experience and aptitude. The clinical time for the production of restorations has been considerably reduced. The material showed good flow, shine, and polish in the immediate result. However, the finishing and polishing of the restorations required a longer clinical period than usual and in the short- term follow-up, flaws in the gingival margins and a new finishing and polishing procedure were necessary. Therefore, the technique described in this article can be considered a restorative alternative, but it is still not able to replace the tradit ional method of making previous esthetic restorations.

Este artículo tiene como objetivo describir un caso clínico del uso de la técnica restauradora inyectable con resina compuesta en un paciente con una queja estética en los dientes anteriores. Producir restauraciones directas en dientes anteriores cuando se realizan con resina compuesta demanda un largo tiempo clínico. Los resultados a menudo dependen de la capacidad del operador para reproducir la forma, la función y la estética adecuadas. Últimamente, la versatilidad de las resinas compuestas ha aumentado. A medida que este material evolucionó, se introdujeron nuevas técnicas para simplificar el proceso de restauración y ahorrar tiempo. La técnica restauradora con resina compuesta fluida inyectable, además de una entrega más rápida y segura, es capaz de aumentar la previsibilidad de los resultados del tratamiento. Sin embargo, se sabe que las resinas fluidas tienen menor resistencia al desgaste y estabilidad del color en comparación con las resinas convencionales. Así, se introdujo en el mercado una versión de este material con un mayor contenido de relleno en su composición, con el objetivo de mejorar la resistencia al desgaste y la retención del brillo. Se necesitan estudios a largo plazo que evalúen el uso de resinas de baja viscosidad. La técnica inyectable es capaz de reproducir fielmente la morfología obtenida en el encerado del caso, generando un resultado estético y funcional satisfactorio. A pesar de simplificar la fabricación de restauraciones en comparación con la técnica convencional, todavía es necesario que el operador tenga cierta experiencia y aptitud. El tiempo clínico para la producción de restauraciones se ha reducido considerablemente. El material mostró buena fluidez, brillo y pulido en el resultado inmediato. Sin embargo, el acabado y pulido de las restauraciones requirió de un período de tiempo clínico más largo de lo habitual y en el seguimiento a corto plazo, fueron necesarios defectos en los márgenes gingivales y un nuevo procedimiento de acabado y pulido. Por lo tanto, la técnica descrita en este artículo puede considerarse una alternativa restauradora, pero aún no es capaz de reemplazar el método tradicional de realizar restauraciones estéticas previas.

Rendimiento Clínico de las Restauraciones Adhesivas con Resina Compuesta en Casos de Pacientes con Desgaste Severo e Incremento de Dimensión Vertical: Revisión de Literatura Sistematizada / Clínical Performance of Adhesive Restorations with Composite Resin in Cases of Patients with Severe Wear and Increased Vertical Dimension: Systematized Literature Review

El desgaste dental severo se describe como la pérdida sustancial de la estructura dental, con exposición de la dentina y pérdida significativa de igual o más de 1/3 de la corona clínica. El uso de materiales compuestos de resina permite al clínico ser más conservador, debido a su aplicación mínimamente invasiva. Además de ello, son relativamente económicas, proporcionan buena estética general, así como un buen rendimiento y facilidad en la reparación. El objetivo de esta revisión de literatura sistematizada es recopilar información disponible en la literatura referente a cuál es el rendimiento clínico de las restauraciones adhesivas con resina compuesta en casos de pacientes con desgaste severo e incremento de la dimensión vertical como objetivo rehabilitador. Se analizaron artículos entre los años 2000 y 2022, seleccionando cuatro bases de datos (Pubmed, Scopus, Scielo y Web of Science). Para identificar los descriptores se utilizó los Medical subject headings (Mesh): Tooth Wear, Composite Restorations, Resin y Oral Rehabilitation. No se aplicó restricciones de idioma, país de origen, autor o lugar de publicación donde se realizó el estudio. Como resultado de la búsqueda se obtuvieron 71 artículos, de los cuales se seleccionaron 5 que cumplieron con los criterios de elegibilidad para ser considerados en la revisión de literatura sistematizada. Se encontró un promedio de tasa de éxito ente el 89,4 % - 100 % en un promedio total de 5.2 años de seguimiento. Se puede concluir, hasta donde se tiene conocimiento en la literatura científica disponible, que el tratamiento de restauraciones adhesivas con resinas compuestas en pacientes con desgaste severo es recomendable, enfocado en un periodo a corto-mediano plazo (3-5 años), siendo una opción de tratamiento económica y mínimamente invasiva.

Severe tooth wear is described as the substantial loss of tooth structure, with dentin exposure and significant loss of equal to or more than 1/3 of the clinical crown. The use of resin composite materials allows the clinician to be more conservative, due to its minimally invasive application. In addition to this, they are relatively inexpensive, provide good general aesthetics, as well as good performance and ease of repair. The objective of this systematic literature review is to collect information available in the literature regarding the clinical performance of adhesive restorations with composite resin in cases of patients with severe wear and increase in the vertical dimension as a rehabilitation objective. Articles between the years 2000 and 2022 were analyzed, selecting four databases (Pubmed, Scopus, Scielo and Web of Science). To identify the descriptors, the Medical subject headings (Mesh) were used: Tooth Wear, Composite Restorations, Resin and Oral Rehabilitation. No language, country of origin, author or place of publication restrictions where the study was conducted were applied. As a result of the search, 71 articles were obtained, of which 5 were selected that met the eligibility criteria to be considered in the systematic literature review. An average success rate between 89.4 % - 100 % was found in a total average of 5.2 years of follow-up. It can be concluded, to the best of our knowledge in the available scientific literature, that the treatment of adhesive restorations with composite resins in patients with severe wear is recommendable, focused on a short-medium term period (3-5 years), being a Inexpensive and minimally invasive treatment option.

Restauração transcirúrgica: inter-relação periodontia e dentística / Transsurgical restoration: interrelationship between periodontics and dentistry

Tendo em vista a importância da relação Dentística Restauradora e Periodontia na Odontologia atual, o presente estudo demonstrou o relato de um caso clínico realizado no Complexo Odontológico do Centro Universitário da Serra Gaúcha (FSG), retratando um procedimento de restauração transcirúrgica em um paciente cujo elemento 13 estava comprometido com uma cavidade subgengival disto-palatino, sendo a resina composta o material restaurador de escolha. Este estudo teve como objetivo apresentar um caso clínico demonstrando a técnica de restauração transcirúrgica e a integração do planejamento entre Periodontia e Dentística Restauradora realizado na Clínica de Odontologia do Centro Universitário da Serra Gaúcha -FSG. Este trabalho mostrou a importância da realização de uma técnica cirúrgica e restauradora correta por parte dos cirurgiões-dentistas, assim como na verificação de que os tecidos periodontais podem reagir de forma positiva à presença de materiais restauradores adesivos posicionados subgengivalmente(AU)

In view of the importance of the restorative dentistry and periodontics relationship in current dentistry, the present study demonstrated the report of a clinical case carried out in the Dental Complex of the Centro Universitário da Serra Gaúcha - FSG, portraying a transsurgical restoration procedure in a patient whose element 13 was compromised with a subgingival cavity of this-palatine, the composite resin being the restorative material of choice. This study aimed to present a clinical case demonstrating the technique of transsurgical restoration and the integration of planning between Periodontics and Restorative Dentistry carried out at the Dentistry Clinic of the University Centro Universitário da Serra Gaúcha - FSG. This study showed the importance of performing a correct surgical and restorative technique by dentists, as well as in verifying that periodontal tissues can react positively to the presence of adhesive restorative materials positioned subgingival(AU)

Envelhecimento bucal precoce e suas consequências para a cavidade oral com foco em reabilitação com resina composta: relato de caso / Early oral aging and its consequences for the oral cavity focusing on rehabilitation with composite resin: case report

O envelhecimento bucal precoce apresenta cada vez uma maior incidência nos consultórios odontológicos e sua degradação aos tecidos orais exige uma atenção por parte do cirurgiãodentista devido ao seu alto grau de complexidade. Esse envelhecimento precoce é causado principalmente por hábitos parafuncionais, dieta ou ambos. Suas consequências são desgastes patológicos dos tecidos dentários, extrusão passiva, perda de dimensão vertical e comprometimento estético e funcional. Por conta disso, o presente estudo teve como objetivo realizar um relato de caso clínico em um paciente jovem e com queixa estética como consequência de hábitos parafuncionais, aonde foram realizados uma reabilitação oral envolvendo aumento da dimensão vertical de oclusão através de Table Tops sem desgastes dentários e restaurações estéticas, ambas com resina composta. Essa reabilitação devolveu a DVO da paciente, trazendo conforto, contatos estáveis, guias de desoclusão e satisfação estética e funcional por parte da paciente(AU)

Early oral aging has an increasing incidence in dental offices and its degradation to oral tissues requires attention from the dentist due to its high degree of complexity. This premature aging is mainly caused by parafunctional habits, diet, or both. Its consequences are pathological wear of dental tissues, passive extrusion, loss of vertical dimension and aesthetic and functional impairment. Because of this, the present study aims to carry out a clinical case report in a young patient with an aesthetic complaint as a result of parafunctional habits, where an oral rehabilitation was carried out involving an increase in the vertical dimension of occlusion through Table Tops without dental wear and aesthetic restorations, both with composite resin. This rehabilitation returned the patient's OVD, bringing comfort, stable contacts, disocclusion guides and aesthetic and functional satisfaction on the part of the patient(AU)

Facetas diretas em resina composta utilizando o fluxo digital para planejamento: relato de caso / Direct facets in composite resin using digital flow for planning: case report / Facetas directas en resina compuesta utilizando flujo digital para planificación: reporte de caso

Introdução:O aprimoramento das resinas compostas nos últimosanos em associação com a difusão de informações nas redes sociais tornou as facetas diretas tratamentos populares na dentística restauradora. No entanto, são procedimentos que exigem ampla destreza manual e conhecimento técnico. O fluxo digital através doescaneamento, enceramento digital e prototipagem 3D para construção de guias tem se tornado uma excelente alternativa para aumentar a previsibilidade e aumentar a longevidade destes trabalhos. Objetivo:Descrever o protocolo de confecção de facetas diretas em resina composta, através de um relato de caso, utilizando como auxílio o planejamento digital para confecção de modelo 3D, guia de silicone e paredes palatinas. Descrição do Caso:Paciente do gênero masculino, 43 anos, queixava-se do formato dos seus dentes. Ao exame clínico percebeu-se desgaste dental nos incisivos centrais e linha do sorriso levemente invertida. Após duas sessões de clareamento de consultório com Peróxido de hidrogênio (35%) e mockup direto com resina composta, foi realizada a moldagem e escaneamento do modelo de gesso no laboratório. O enceramento digital foi aprovado, o modelo 3D foi impresso para confecção da guia de silicone. Com auxílio da guia foram executadas facetas diretas nos elementos 13, 12, 11, 21, 22 e 23. Conclusão:O fluxo digital pode ser uma alternativa viável para minimizar as falhas na confecção de facetas diretas em resina composta (AU).

Introduction:The improvement of composite resins in recent years, together with information disseminated on social media, has made direct veneers popular treatments in restorative dentistry. However, these procedures require significant manual dexterity and technical knowledge. Digital work flow using scanning, digital wax-up and 3D prototyping for the construction of guides has become an excellent alternative to increase predictability and the longevity of these procedures. Objective:Describe the manufacturing protocol for direct composite resin veneers, using a case report and digital to construct the 3D model, silicone guide and palatine walls. Case description:Male patient, 43 years old, complained of the shape of his teeth. Clinical examination revealed tooth wear on the central incisors and a slightly inverted smile line. After two whitening sessions with hydroigen peroxide (35%) and direct mockup with composite resin, the plaster model was molded and scanned in the laboratory. Digital wax-up was approved, and the 3D model was printed to manufacture the silicone guide. With the help of the guide, the direct veneers were applied to elements 13, 12, 11, 21, 22 and 23.Conclusions:Digital flow may be a feasible alternative to minimize manufacturing flaws in direct composite resin veneers (AU).

Introducción: La mejora de las resinas compuestas en los últimos años, y la difusión de información en las redes sociales, ha popularizado las facetas directas en los tratamientos en odontología restauradora. Sin embargo, son procedimientos que requieren demasiado destreza manual y conocimientos técnicos. El flujo digital usando escaneo, encerado digital y prototipado 3D para la construcción de guías se ha convertido en una excelente alternativa para aumentar la previsibilidad y la longevidad de estos procedimientos. Objetivo: Describir el protocolo para la realización de carillas directas en resina compuesta, a través de un reporte de caso, utilizando el planeo digital como ayuda para la realización de un modelo 3D, guía de silicona y paredes palatinas. Descripción del caso: Paciente masculino, 43 años, se quejó de la forma de sus dientes. El examen clínico reveló desgaste dental en los incisivos centrales y una línea de sonrisa levemente invertida. Después de dos sesiones de blanqueamiento en consultorio con peróxido de hidrógeno (35%) y maqueta directa con resina compuesta, el modelo de yeso fue moldeado y escaneado en el laboratorio. El encerado digital fue aprovado, el modelo 3D fue impreso para hacer la guía de silicona. Con la ayuda de la guía se realizaron carillas directas en los elementos 13, 12, 11, 21, 22 y 23. Conclusiones: El fluxo digital puede ser una alternativa viable para minimizar fallas en la fabricación de carillas directas en resina compuesta (AU).

Bond strength of composite resin/universal adhesive to dentin submitted to radiotherapy / Fuerza de unión de resina compuesta/adhesivo universal a dentina sometida a radioterapia

Aim: To evaluate the bond strength of a universal adhesive system to dentin submitted to radiotherapy. Materials and Methods: Sixty extracted human teeth were divided into two groups (n = 30): without radiotherapy (control); with radiotherapy, according to the adhesive protocol (n=15): ER-etch-and-rinse (acid + Single Bond Uni-versal); SE-self-etch (Single Bond Universal). The analyzes were shear bond strength (SBS) (n=10), failure pattern (n=10) and scanning electron microscopy (n=5). Data was analyzed by a two-way ANOVA (α =0.05). Results: The radiotherapy decreased SBS of the restorative material to dentin (p<0.0001). The ER protocol provided lower bond strength values (p<0.001). The predominant type of fracture without radiotherapy was mixed (SE), cohesive to the material (ER). Both protocols presented adhesive failures with radiotherapy. Teeth had a hybrid layer and long resin tags (without radiotherapy) and few tags (with radiotherapy). Conclusions: The SE adhesive mode favors the shear bond strength of resin to dentin in teeth submitted to radiotherapy.

Objetivo: Evaluar la fuerza de adhesión de un sistema adhesivo universal a la dentina sometida a radioterapia. Materiales y Métodos: Sesenta dientes humanos extraídos se dividieron en dos grupos (n = 30): sin radioterapia (control); con radioterapia, según protocolo adhesivo (n=15): ER-grabado y enjuague (ácido + Single Bond Universal); autograbado SE (Single Bond Universal). Los análisis ejecutados fueron resistencia al cizallamiento (SBS) (n=10), patrón de falla (n=10) y microscopía electrónica de barrido (n=5). Los datos se sometieron al test de ANOVA de dos vías (α =0,05). Resultados: La radioterapia disminuyó la SBS del material restaurador a la dentina (p<0,0001). El protocolo ER proporcionó valores de fuerza de unión más bajos (p<0,001). El tipo de fractura predominante sin radioterapia fue mixta (SE), cohesiva al material (ER). Ambos protocolos presentaron fallas adhesivas con radioterapia. Los dientes tenían una capa híbrida y colas de resina largas (sin radioterapia) o pocas colas de resina (con radioterapia). Conclusión: El modo adhesivo SE favorece la resistencia al corte de la resina a la dentina en dientes sometidos a radioterapia.

Efecto del tratamiento de la morfología oclusal con materiales para restauraciones preventivas / Effect of treating occlusal morphology with materials for preventive restorations

Introducción: las fosas y fisuras son áreas formadas por delgadas irregularidades de la capa del esmalte de la superficie oclusal. La compleja morfología en dientes posteriores es un determinante biológico asociado al desarrollo de caries. Objetivo: evaluar el efecto de diversas formas de tratar la morfología oclusal en la adaptación y penetración de materiales utilizados en restauraciones preventivas. Material y métodos: diseño experimental e in vitro. Sesenta terceros molares fueron distribuidos aleatoriamente en dos grupos: surco sin ameloplastia y con ameloplastia; además, contaban con acondicionamiento del esmalte que se subdividió en tres subgrupos: 1) sellador de fosas y fisuras, 2) adhesivo/sellador de fosas y fisuras y 3) adhesivo/ resina Flow. Resultados: los subgrupos adhesivo/sellador y adhesivo/ Flow alcanzaron mayores valores de adaptación íntima a las paredes del surco. Las diferencias fueron significativas entre los materiales (p = 0.0009). Las mayores zonas de desadaptación resultaron para el sellador sin y con ameloplastia. La penetración de los materiales fue mayor en los surcos con ameloplastia. En los surcos tratados con ameloplastia, el adhesivo/Flow reveló el mayor porcentaje de penetración y la mejor adaptación a las paredes del surco. Conclusiones: la penetración del material está positivamente correlacionada con la profundidad del surco. El sellador con y sin ameloplastia mostró pobre adaptación a las paredes del surco (AU)

Introduction: pits and fissures are areas formed by fine irregularities in the enamel layer of the occlusal surface. The complex morphology in posterior teeth are biological determinants associated with the development of caries. Objective: to evaluate the effect of various ways of treating occlusal morphology on the adaptation and penetration of materials used in preventive restorations. Material and methods: experimental design, in vitro. Sixty third molars were randomly distributed into two groups: groove without ameloplasty and with ameloplasty, with enamel conditioning with three subgroups: 1) pit and fissure sealer, 2) adhesive/pit and fissure sealer, 3) adhesive/resin flow. Results: the adhesive/sealant and adhesive/flow subgroups reached higher values of intimate adaptation to the furrow walls. The differences were significant between the materials (p = 0.0009). The largest areas of maladjustment were found for the sealant without and with ameloplasty. The penetration of the materials was greater in the grooves with ameloplasty. In the grooves treated with ameloplasty, the adhesive/flow revealed the highest percentage of penetration and the best adaptation to the walls of the groove. Conclusions: the penetration of the material is positively correlated with the depth of the furrow. The sealant with and without ameloplasty showed poor adaptation to the sulcus walls (AU)

Influence of different surface treatments on bond strength of a Self-Adhesive resin cement to CAD-CAM materials / Influencia de los diferentes tratamientos superficiales en la unión del cemento resinoso autoadhesivo a los materiales CAD-CAM

To evaluate the shear bond strength (SBS) of self-adhesive resin cement when used with two different computer-aided design (CAD)-computer-aided manufacturing (CAM) materials after various surface treatments. Nanoceramic resin Lava Ultimate (LU) and feldspathic ceramic Vita Mark II (VM) CAD-CAM block samples were prepared with 1.5-mm thickness, and a total of 90 samples were obtained (N=90), with five samples of each block. The samples were divided into the following five groups according to the surface treatments (n=9): group 1, untreated (control); group 2,5% hydrofluoric acid etching; group 3, Er: YAG laser irradiation; group 4, tribochemical silica coating (Cojet); and group 5, air-abrasion with Al2O3. After silane application, resin cement was applied on a transparent matrix (diameter, 3mm; height, 2mm) on the blocks. SBS was determined using a universal testing device at a crosshead speed of 1mm/min. Two-way analysis of variance (ANOVA) and Tukey's post hoc tests were used to analyze the SBS values. LU showed the highest SBS value in group 4. The average SBS values in groups 3 and were found to be lower than that in the control group (p<0.05). When VM was examined, while all surface treatments increased the SBS values significantly, the highest SBS value was observed in group 4 (p<0.05). This study revealed that all surface treatments used negatively affected the bond strength values of self-adhesive resin cement to LU, except for Cojet application. The SBS values of resin cement with VM increased in all surface treatment application groups.

Evaluar la resistencia de unión al corte (SBS) del cemento de resina autoadhesivo cuando se utiliza con dos materiales diferentes de diseño asistido por computadora (CAD) y fabricación asistida por computadora (CAM) después de varios tratamientos superficiales. Se prepararon muestras de bloques CAD-CAM de resina Lava Ultimate (LU) y cerámica feldespática Vita Mark II (VM) con un espesor de 1,5mm, y se obtuvieron un total de 90 muestras (N=90), con cinco muestras de cada bloque. Las muestras se dividieron en los siguientes cinco grupos según los tratamientos superficiales (n=9): grupo 1, sin tratar (control); grupo 2, grabado con ácido fluorhídrico al 5%; grupo 3, irradiación con láser Er: YAG; grupo 4, recubrimiento triboquímico de sílice (Cojet); y grupo 5, aire-abrasión con Al2O3. Después de la aplicación de silano, se aplicó cemento de resina sobre una matriz transparente (diámetro, 3mm; altura, 2mm) sobre los bloques. La SBS se determinó usando un dispositivo de prueba universal a una velocidad de cruceta de 1mm/min. Se utilizaron análisis de varianza bidireccional (ANOVA) y pruebas post hoc de Tukey para analizar los valores de SBS. LU mostró el valor más alto de SBS en el grupo 4. Los valores promedio de SBS en los grupos 3 y fueron más bajos que en el grupo de control (p<0,05). Cuando se examinó VM, mientras que todos los tratamientos superficiales aumentaron significativamente los valores de SBS, el valor más alto de SBS se observó en el grupo 4 (p<0,05). Este estudio reveló que todos los tratamientos de superficie utilizados afectaron negativamente los valores de resistencia de la unión del cemento de resina autoadhesivo a LU, a excepción de la aplicación Cojet. Los valores de SBS del cemento de resina con VM aumentaron en todos los grupos de aplicación de tratamiento de superficie.

Biomechanical and chemical behavior of various bioactive materials in class II restorations / Desempeño biomecánico y químico de diferentes materiales bioactivos en restauraciones clase II

The aim of this in vitro study was to evaluate the biomechanical and chemical behavior of various bioactive materials in class II MOD restorations. Forty- eight standardized class II MOD cavities were prepared in sound extracted human molar teeth. The specimens were divided into four groups according to the restorative material: Group 1 (Filtek™ Z350 XT), Group 2 (Biodentine™ as a liner, and then restored with Filtek™ Z350 XT), Group 3 (Cention N™), and Group 4 (Activa™ Bioactive-Restorative). The samples were tested for fracture resistance by subjecting them to a compressive load in a Universal testing Machine. The failure modes of each specimen were evaluated. The alkalinizing potential and calcium ion release of the materials were measured. SEM-EDAX analyses were also performed for all materials. Data were analyzed using ANOVA and post hoc Tukey test (p<0.05). Group 1 showed the higher fracture resistance (p<0.05). Group 3 had greater fracture resistance values but no statistical difference from Group 4. Biodentine™ showed greater biomineralization potential. Class II MOD restorations of Group 1 displayed the higher fracture resistance; however, it was highly associated with catastrophic failure. Conversely, Biodentine™ presented a more significant bioactivity potential, and its use, as in Group 2, promoted the most favorable failure mode.

El objetivo de este estudio, in vitro, fue evaluar el desempeño biomecánico y químico de varios materiales bioactivos en restauraciones clase II MOD. Se prepararon cuarenta y ocho cavidades clase II MOD estandarizadas en dientes molares humanos extraídos. Las muestras se dividieron en cuatro grupos según el material de restauración: Grupo 1 (Filtek™ Z350 XT), Grupo 2 (Biodentine™ como base y luego restaurado con Filtek™ Z350 XT), Grupo 3 (Cention N™) y Grupo 4 (Activa™ Bioactivo-Reparador). La prueba de resistencia a la fractura fue realizada en una máquina de ensayo universal Instron. Se evaluaron los modos de falla de cada espécimen. Se midió el pH y la liberación de iones de calcio de los materiales. Se realizaron análisis SEM-EDAX. Los datos se analizaron mediante ANOVA y la prueba post hoc de Tukey (p<0,05). El grupo 1 mostró la mayor resistencia a la fractura (p<0,05). El Grupo 3 tuvo mayores valores de resistencia a la fractura que el Grupo 4, pero sin diferencia estadística. Biodentine™ mostró un mayor potencial de biomineralización. Las restauraciones Clase II MOD del Grupo 1 mostraron la mayor resistencia a la fractura; sin embargo, estuvo altamente asociado con fallas irreparables. Por el contrario, Biodentine™ presentó un potencial de bioactividad más significativo y su uso, como en el Grupo 2, promovió el modo de falla más favorable.

Depth of cure, mechanical properties and morphology of dual-cure bulk-Fill composites / Profundidad de curado, propiedades mecánicas y morfología de resinas compuestas duales

This study evaluated selected structural and physical properties, such as degree of conversion (DC), Vickers hardness (VHN), and compression strength (CS), of three new dual-cure bulk-fill resin-based composites (RBCs; ACTIVA, HyperFIL, and Fill-Up) and compared them to those of a conventional RBC (Filtek Z250) at three clinically relevant depths. Samples (n=180) were prepared in three depths (2,4, and 6mm). Fourier-transform infrared spectroscopy (FTIR) analysis and VHN and CS tests were performed. The DC value was calculated by considering the relative change in the aliphatic C=C peaks. The fractured surfaces of representative samples were characterized using scanning electron microscopy (SEM). Data were statistically evaluated using two-way analysis of variance and post hoc Bonferroni tests (p<0.05). According to the VHN results, Filtek Z250 showed the highest bottom/top hardness ratio (97.94±1.01) at 2mm thickness and ACTIVA showed the lowest bottom/top hardness ratio (43.48±5.64) at 6mm thickness (p<0.001). According to the FTIR results, the DC decreased with increasing thickness in all materials (p<0.05). Filtek Z250 showed the highest (301±12.4 MPa) and ACTIVA exhibited the lowest (232±17.2 MPa) CS values at 2mm thickness (p<0.05). The lowest CS values were obtained for ACTIVA, and the highest values were obtained for Filtek Z250 for samples with thicknesses of 4 and 6mm, respectively (p<0.05). The structural features of restorative composites, such as the resin chemistry and filler type and content, and the operational parameters (i.e., material thickness and curing conditions) strongly affect crosslinking reactions and thus the DC, VHN, and CS values.

Este estudio evaluó propiedades físicas y estructurales, como el grado de conversión (DC), la dureza Vickers (VHN) y la resistencia a la compresión (CS), de tres nuevos compósitos a base de resina de curado dual tipo bulk (RBC; ACTIVA , HyperFIL y Fill-Up) y los comparó con los de una resina compuesta convencional (Filtek Z250) en tres profundidades clínicamente relevantes. Se prepararon muestras (n=180) en tres profundidades (2,4 y 6mm). Se realizaron análisis de espectroscopia infrarroja por transformada de Fourier (FTIR) y pruebas VHN y CS. El valor de DC se calculó considerando el cambio relativo en los picos alifáticos C=C. Las superficies fracturadas de muestras representativas se caracterizaron mediante microscopía electrónica de barrido (MEB). Los datos se evaluaron estadísticamente mediante análisis de varianza de dos vías y pruebas post hoc de Bonferroni (p<0,05). De acuerdo con los resultados de VHN, Filtek Z250 mostró la relación de dureza inferior/superior más alta (97,94±1,01) con un espesor de 2mm y ACTIVA mostró la relación de dureza inferior/superior más baja (43,48±5,64) con un espesor de 6mm (p<0,001). De acuerdo con los resultados de FTIR, la DC disminuyó al aumentar el espesor en todos los materiales (p<0,05). Filtek Z250 mostró los valores de CS más altos (301±12,4 MPa) y ACTIVA los más bajos (232±17,2 MPa) a 2mm de espesor (p<0,05). Los valores más bajos de CS se obtuvieron para ACTIVA y los valores más altos para Filtek Z250 para muestras con espesores de 4 y 6mm, respectivamente (p<0,05). Las características estructurales de las resinas compuestas de restauración, como la química; además del tipo y contenido del relleno, y los parámetros operativos (es decir, el espesor del material y las condiciones de curado) afectan en gran medida las reacciones de interacción química y, por lo tanto, los valores de DC, VHN y CS.

Reabilitação estética e funcional com resina composta após trauma dentário: relato de caso / Aesthetic and functional rehabilitation with composite resin after dental trauma: case report

As lesões dentárias traumáticas são um problema de saúde pública mundial, dentre as quais a fratura dentária é a de maior ocorrência, envolvendo principalmente os dentes anteriores. A abordagem de grandes fraturas anteriores é um desafio para cirurgiões dentistas de qualquer nível pois, além da função, afetam diretamente a estética do paciente, fazendo-se necessário um planejamento que envolva diferentes especialidades na odontologia. Objetivo: Relatar um caso clínico de reabilitação funcional e estética de fratura dentária nos incisivos centrais superiores envolvendo tratamento endodôntico, instalação de pino de fibra de vidro e restauração direta em resina composta. Relato de Caso: O paciente de 17 anos sofreu fratura nos incisivos centrais superiores causada por uma queda de bicicleta. Devido à busca tardia por tratamento o elemento 21 foi diagnosticado com necrose pulpar e, portanto, foi submetido à tratamento endodôntico pela Técnica Crown Down e reabilitação com pino de fibra de vidro Splendor-SAP. Posteriormente, os elementos 11 e 21 foram restaurados com facetas diretas em resina composta pela técnica incremental. Conclusão: A reabilitação com instalação de pino de fibra de vidro associada à técnica de estratificação incremental em resina composta se mostra como uma boa opção para reabilitação estética pois permite dar forma anatômica ao dente com riqueza de detalhes na estratificação da dentina e esmalte, além de máxima preservação da estrutura dental. Os resultados obtidos reforçam o sucesso estético e funcional com significativo impacto na qualidade de vida do paciente(AU)

Traumatic dental injuries are a worldwide public health problem, among which dental fractures are the most frequent, mainly involving the anterior teeth. The approach of large anterior fractures is a challenge for dental surgeons of any level because, in addition to function, they directly affect the patient's esthetics, requiring a plan that involves different specialties in dentistry. Objective: Report a clinical case of functional and aesthetic rehabilitation of dental fractures in maxillary central incisors involving endodontic treatment, installation of a fiberglass post and direct restoration in composite resin. Case Report: The 17-year-old patient suffered a fracture in the upper central incisors caused by a fall from a bicycle. Due to the late search for treatment, element 21 was diagnosed with pulp necrosis and, therefore, underwent endodontic treatment using the Crown Down Technique and rehabilitation with a Splendor-SAP fiberglass pin. Later, elements 11 and 21 were restored with direct veneers in composite resin using the incremental technique. Conclusion: Rehabilitation with the installation of a fiberglass post associated with the incremental layering technique in composite resin is a good option for aesthetic rehabilitation as it allows the anatomical shape of the tooth with rich details in the layering of dentin and enamel, in addition to maximum preservation of the tooth structure. The results obtained reinforce the aesthetic and functional success with a significant impact on the patient's quality of life(AU)

Tratamento endodôntico em dente permanente traumatizado com rizogênese incompleta: relato de caso / Endodontic treatment in permanent traumatised tooth with incomplete rhizoganis: case report / Tratamiento endodóntico en diente permanente traumatizado con rizoganis incompleta: presentación de un caso

Os traumatismos dentários representam um problema de saúde pública devido à alta prevalência e impacto psicossocial, sendo muito frequentes em crianças podendo resultar em necrose pulpar e culminar na rizogênese incompleta de dentes permanentes. Nestes casos de traumatismos em dentes permanentes com rizogênese incompleta e necrose pulpar, o tratamento mais indicado pela literatura é a apicificação, sendo um tratamento complexo e longo. Considerando a importância deste tema, o objetivo deste trabalho é relatar o caso de um paciente com traumatismo dental e necrose pulpar, que acarretou a interrupção do desenvolvimento completo e adequado do ápice dentário, sendo necessária a intervenção por meio da técnica de apicificação e o acompanhamento a longo prazo. O caso trata-se de uma menina em que um traumatismo dentário acarretou fratura de um incisivo central superior com formação radicular incompleta, comprometendo tanto a estética quanto a vitalidade do dente. Foi realizado o tratamento endodôntico com apicificação e posteriormente ao plug apical de MTA. O dente foi restaurado definitivamente com resina composta e realizado acompanhamento do paciente. Nas consultas de acompanhamento houve ausência de sintomatologia dolorosa e satisfação da paciente com a aparência atual. Sendo assim, a apicificação apresenta-se como uma ótima alternativa para dentes com rizogênese incompleta e necrose pulpar, embora longo houve uma melhora estética e satisfação do paciente.

Dental trauma represents a public health problem due to its high prevalence and psychosocial impact, being very frequent in children and can result in pulp necrosis and culminate in incomplete root formation of permanent teeth. In these cases of trauma to permanent teeth with incomplete root formation and pulp necrosis, the most indicated treatment in the literature is apexification, which is a complex and long treatment. Considering the importance of this topic, the objective of this work is to report the case of a patient with dental trauma and pulp necrosis, which caused the interruption of the complete and adequate development of the dental apex, requiring intervention through the apexification technique and follow-up. long-term. The case is about a girl in which a dental trauma resulted in a fracture of a maxillary central incisor with incomplete root formation, compromising both the esthetics and the vitality of the tooth. Endodontic treatment was performed with apexification and then apical MTA plug. The tooth was definitively restored with composite resin and the patient was followed up. In the follow- up consultations, there was no painful symptomatology and the patient was satisfied with her current appearance. Thus, the apexification presents itself as a great alternative for teeth with incomplete root formation and pulp necrosis, although in the long run there was an aesthetic improvement and patient satisfaction.

Los traumatismos dentales representan un problema de salud pública debido a su alta prevalencia e impacto psicosocial, siendo muy frecuentes en niños y pudiendo dar lugar a necrosis pulpar y culminar en la formación incompleta de la raíz de los dientes permanentes. En estos casos de traumatismos en dientes permanentes con formación radicular incompleta y necrosis pulpar, el tratamiento más indicado en la literatura es la apexificación, que es un tratamiento complejo y largo. Considerando la importancia de este tema, el objetivo de este trabajo es relatar el caso de una paciente con traumatismo dentario y necrosis pulpar, que causó la interrupción del desarrollo completo y adecuado del ápice dentario, requiriendo intervención a través de la técnica de apexificación y seguimiento. a largo plazo. Se trata de una niña en la que un traumatismo dental provocó la fractura de un incisivo central maxilar con formación radicular incompleta, comprometiendo tanto la estética como la vitalidad del diente. Se realizó tratamiento endodóntico con apexificación y posterior taponamiento apical con MTA. El diente fue restaurado definitivamente con resina compuesta y el paciente fue sometido a seguimiento. En las consultas de seguimiento, no había sintomatología dolorosa y la paciente estaba satisfecha con su aspecto actual. Así, la apexificación se presenta como una gran alternativa para dientes con formación radicular incompleta y necrosis pulpar, aunque a la larga se produjo una mejoría estética y satisfacción de la paciente.

Effect of low temperature and room temperature on the depth of cure of bulk-fill composite resins

The study analyzed the influence of temperature on the depth of cure of bulk-fill composite resins. Three discs (ISO 4049/2000) from each group were made, and four restorative materials were investigated: Opus Bulk-Fill Flow, Opus Bulk-Fill APS, Filtek™ One Bulk-Fill, and Filtek™ Bulk-Fill Flow. They were light-cured (Gnatus ± 1,200 mW/cm2) for 20 seconds, varying the temperature (23°C and 5°C) and simulating the use of the product both at room temperature and under refrigeration. The materials were inserted in aluminum matrices with 10 mm in depth and 4 mm in diameter. A clear film strip and a glass microscope slide were positioned at the top and bottom surfaces. The material was condensed and light-cured with the tip of the light source in close contact, for 20 seconds on the top surface. Immediately after irradiation, the samples were removed from the mold, and the uncured part was removed with a plastic spatula. The measurement was performed with a micrometer ± 0.1 mm, and the value was divided by 2. The data were analyzed with two-way ANOVA at a significance of 0.05. There was a statistical difference in the temperature between the results obtained in Opus Bulk-Fill APS (p <0.001) and Filtek™ Bulk-Fill Flow (p = 0.018) resins. For the temperature of 5°C, Filtek™ Bulk-Fill Flow showed a statistical difference compared to the other resins, while Opus Bulk-Fill Flow and Opus Bulk-Fill APS did not. For the temperature of 23°C, Filtek™ Bulk-Fill Flow maintained the statistical difference from the others, but Filtek™ One Bulk-Fill and Opus Bulk-Fill APS did not present statistical differences. Storing the Filtek™ Bulk-Fill Flow composite resin in the refrigerator caused a greater depth of cure than the other resins, and the depth of cure decreased at room temperature. As for Opus Bulk-Fill APS, the depth of cure decreased proportionally to the temperature decrease. The temperature may affect the depth of cure of some composite resins.

Evidence-practice gap in treatment decisions about defective composite and amalgam restorations among Brazilian dentists

Better understanding of dentists' decision-making about defective restorations is needed to close the evidence-practice gap (EPG). This study aimed to quantify the EPG about defective restorations and identify dentist factors associated with this EPG. Methods: 216 dentists from São Paulo State, Brazil, completed a questionnaire about three clinical case scenarios involving defective composite restorations with cementum-dentin margins (case 1) and enamel margins (case 2), and an amalgam (case 3) restoration. Dentists were asked what treatment, if any, they would recommend, including preventive treatment, polishing, re-surfacing, or repairing the restoration, or replacing the entire restoration. Replacing the entire restoration in any of these three scenarios was classified as inconsistent with the evidence, comprising an EPG. Bivariate analyses using Chi-square, ANOVA, or multiple comparison tests were performed (p<.05). Results: for defective composite restorations, 49% and 55% of dentists chose to replace the entire restoration for cases 1 and 2, respectively. Twenty-nine percent of dentists chose to replace the entire amalgam restoration. Dentists were significantly more likely to choose to replace the defective amalgam restoration than the composite restoration with a defect at the cementum-dentin margins or the enamel margins (both at p < .001). Female dentists were more likely to choose a conservative treatment than male dentists for cases 1 (p=.034) and 2 (p=.009). Dentists with a higher percentage of patients interested in individualized caries prevention were also more conservative in case 1 (p=.045). Conclusion: a substantial EPG regarding treatment decisions for defective restorations exists, especially for composite restorations. This study adds to the international evidence that an EPG exists in this clinical area and that global strategies need to be developed to close the gap

Effect of time and dental substrate on the bond strength of a universal adhesive system: in vitro study / Efeito do tempo e do substrato dental na resistência de união de um sistema adesivo universal: estudo in vitro

Introduction: Dentin adhesives provide union between the dental substrate and composite resin, but this union can be influenced by the cleaning agent. Objective: Evaluate the use of ozonated water as a cavity cleaning solution. Material and method: 40 bovine dental crowns were selected, divided into four groups: AD (dentin cleaning with distilled water) and AO (dentin cleaning with ozonized distilled water). Each group was divided into two storage periods (24h and 30 days) kept at 37 °C. The selected universal system adhesive was employed according to the manufacturer's instructions and light cured for 20 seconds. At that time, three cylinders were made (Tygon matrix with an internal diameter of 2 mm and a height of 2 mm) of composite resin in the crowns in the cervical, médium, and incisal regions and light cured for 30 seconds. After storage, the bonding strength was tested by micro-shear, and fracture type analysis was performed. The data were submitted to statistical analysis using the Shapiro-Wilk test with a significance level of 95%, ANOVA, and Turkey. Result: There was a statistically significant difference between the bond strength values, only in the intergroup analysis for the time of 24 hours, between the middle third of the groups (LDAO24 = 2.70 (± 2.39); LDAO30 = 3.82 (± 2.31)). The predominant fracture type for both groups was an adhesive fracture, except in the medium and incisal thirds of the AD, which was a cohesive dentin fracture. Conclusion: The utilization of ozone did not change the bond strength adhesive.

Introdução: Os adesivos dentinários proporcionam união entre o substrato dental e resina composta, porém esta união pode ser influenciada pelo agente de limpeza. Objetivo: Avaliar a influência na resistência de união (RU) de um sistema adesivo universal associado à da água ozonizada como solução de limpeza cavitária. Material e método: Foram selecionadas 40 coroas de dentes anteriores bovinos divididos em 4 grupos: AD (limpeza dentinária com água destilada) e AO (limpeza dentinária com água destilada ozonizada). Cada grupo foi subdividido em outros dois grupos de acordo com o tempo de armazenamento (24h e 30 dias) armazenados a 37ºC. A limpeza dentinária foi realizada por meio de uma seringa de 60mL de cada solução e fricção por 10 segundos. O sistema adesivo universal selecionado foi aplicado de acordo com as instruções do fabricante e fotoativado por 20 segundos. Em seguida, foram confeccionados 3 cilindros (matriz Tygon com um diâmetro interno de 2 mm e 2 mm de altura) de resina composta nas coroas nas regiões cervical, média e incisal e fotoativados por 30 segundos. Após o armazenamento foi realizado o teste de RU por microcisalhamento e análise do tipo de fratura. Os dados coletados foram submetidos a análise estatística através do teste de Shapiro Wilk com nível de significância de 95%, ANOVA e Tukey. Resultado: Houve diferença estatística significativa entre os valores de RU apenas na análise intergrupos para o tempo de 24 horas, entre o terço médio dos grupos (LDAO24 = 2,70 (± 2,39); LDAO30 = 3,82 (± 2,31)). O tipo de fratura predominante para ambos os grupos em todos os tempos foi de fratura adesiva, com exceção ao terço médio e incisal do AD, que foi fratura coesiva de dentina. Conclusão: A utilização do ozônio não alterou a resistência de união adesiva.

Grado de microfiltración en ionómero de vidrio y resina compuesta nanoparticulada en lesiones cervicales no cariosas / Degree of microleakage in glass ionomer and nanoparticulate composite resin in non-carious cervical lesions

Introducción: El grado de microfiltración en el ionómero de vidrio y la resina compuesta nanoparticulada en lesiones cervicales no cariosas es de gran importancia para elegir el material restaurador más adecuado para cada caso clínico. Objetivo: Describir el grado de microfiltración en ionómero de vidrio y resina compuesta nanoparticulada en lesiones cervicales no cariosas. Métodos: Se realizó una revisión bibliográfica, correspondiente al nivel exploratorio, en busca de responder cinco preguntas científicas sobre el tema. Se identificaron 62 artículos de las bases de datos de Google Académico o Scopus entre 2015 y 2022. Resultados: Los estudios consultados sugieren que la resina compuesta nanoparticulada es una opción de restauración efectiva y estética en odontología, especialmente en casos de cavidades de alta carga mecánica y estética dental. Los estudios de casos que se revisan demuestran que el grado de microfiltración en las lesiones cervicales no cariosas puede ser significativamente mayor en las restauraciones con ionómero de vidrio en comparación con las resinas compuestas nanoparticuladas. Conclusiones: Se concluye que el elemento fundamental en el tratamiento es realizar un correcto diagnóstico, determinando las necesidades para mejorar la salud dental y realizar una correcta planificación, por lo que es necesario conocer los diferentes tipos de tratamientos con la finalidad de seleccionar el más adecuado, que cumpla con las características biológicas, mecánicas y estéticas, ya que uno de los objetivos fundamentales de cualquier tratamiento es devolver la función y la estética de modo satisfactorio y con la mayor durabilidad posible.

Introduction: The degree of microleakage in glass ionomer and nanoparticulated composite resin in non-carious cervical lesions is of great importance for choosing the most suitable restorative material for each clinical case. Objective: To describe the degree of microleakage in glass ionomer and nanoparticulated composite resin in non-carious cervical lesions. Methods: A literature review, corresponding to the exploratory level, was carried out to answer five scientific questions on the subject. Sixty-two articles were identified from Academic Google or Scopus databases between 2015 and 2022. Results: The studies consulted suggest that nanoparticulated composite resin is an effective and esthetic restorative option in dentistry, especially in cases of cavities with high mechanical load and dental esthetics. The case studies reviewed demonstrate that the degree of microleakage in non-carious cervical lesions can be significantly higher in glass ionomer restorations compared to nanoparticulated composite resins. Conclusions: It is concluded that the fundamental element in treatment is to carry out a correct diagnosis, determining the needs to improve dental health and to carry out correct planning, so it is necessary to know the different types of treatments with the aim of selecting the most suitable one, which complies with the biological, mechanical and esthetic characteristics, since one of the fundamental objectives of any treatment is to restore function and esthetics in a satisfactory way and with the greatest possible durability.