Evaluation of microleakage of mineral trioxide aggregate and biodentine as apical barriers in simulated young permanent teeth.

BACKGROUND: Apexification is a procedure that promotes apical closure by forming mineralized tissue in the apex region of a nonvital young permanent tooth. Calcium silicate-based cement like Mineral trioxide aggregate (MTA) and Biodentine are commonly employed as apical barriers to facilitate this process. Microleakage, defined as the leakage along the junction between the canal wall and filling material, is a crucial aspect to assess in MTA and Biodentine applications as apical barriers, as it directly impacts the prevention of bacterial seepage and maintenance of structural integrity. The current study aims to assess the microleakage of MTA and Biodentine when used as apical barriers in simulated young permanent teeth. METHODS: From a total of 128 extracted teeth, 114 were selected for the study and randomly allocated into three groups: G1 (MTA), G2 (Biodentine), and G3 (Control), with 38 teeth per group. After excluding 5 teeth from each group due to issues such as canal calcification, breakage during sectioning, and procedural errors, 33 teeth were analyzed to ensure equal distribution. To simulate young permanent teeth, samples were instrumented using a person-reamer with a diameter of 1.7 mm. A 4 mm thick apical plug of MTA and Biodentine was placed in G1 and G2, respectively, while G3 was the control group. Apical microleakage in all experimental groups was assessed using a dye penetration method. Specimens were longitudinally sectioned and examined under a stereomicroscope with graded eyepiece. RESULTS: The Kruskal-Wallis test revealed variations in mean apical microleakage among the groups: G1 recorded 0.67, G2-0.16, and G3-1.62, with G2 showing the lowest value and G3 group exhibiting the highest. CONCLUSIONS: Biodentine was found to excel in its ability to create a secure seal and function effectively as an apical barrier in simulated young permanent teeth. These results underscore its potential as a highly efficient material for dental applications, particularly in scenarios requiring reliable sealing and barrier formation in the root canal system of developing permanent teeth.

Impact of different activation procedures on sodium hypochlorite penetration into dentinal tubules after endodontic retreatment via confocal laser scanning microscopy.

BACKGROUND: Infected dentinal tubules are a possible source of bacteria that are responsible for the failure of root canal treatment. Therefore, disinfection of dentinal tubules by increasing the penetration of the irrigation solution is important for success in retreatment cases. This study utilized confocal laser scanning microscopy (CLSM) to assess and compare the impact of XPR, ultrasonic irrigation (UI) and sonic activation (SA) on NaOCl penetration into dentinal tubules following endodontic retreatment. METHODS: A total of forty mandibular premolars were enrolled in this investigation. Following root canal preparation up to ProTaper X3 file (30/0.07), root canals were obturated with gutta-percha and bioceramic root canal sealer with single cone technique. The root canal filling materials were removed using ProTaper nickel-titanium rotary retreatment files until the working length was reached. The retreatment procedure was finalized using the ProTaper Next X4 (40/0.06). The teeth were divided into four groups based on the irrigation activation technique: control (conventional needle irrigation), SA, UI and XPR. During the final irrigation procedure, Rhodamine B dye was introduced to 5% NaOCl for visualization via CLSM. Subsequent to image acquisition, the maximum penetration, penetration percentage, and penetration area were calculated. Data were statistically analyzed using the Kruskal-Wallis, Friedman, and Bonferroni Dunn multiple comparison tests through R software (p < 0.05). RESULTS: In the middle third, UI yielded a significantly higher penetration percentage than the control group (p < 0.05). The UI and XPR groups showed increased penetration percentages in the coronal and middle thirds compared with the apical third (P < 0.05). Maximum penetration was notably reduced in the apical third than in comparison with the coronal and middle thirds in all groups (p < 0.05). In the control, SA and XP groups, the penetration area was ranked in descending order as coronal, middle and apical (p < 0.05). Conversely, in the ultrasonic group, the penetration area was significantly lower in the apical third than in the middle and coronal thirds (p < 0.05). CONCLUSIONS: UI enhanced the penetration percentage in the middle third of the root compared with that in the control group. XPR and SA showed no significant effect on NaOCl penetration following retreatment.

Influence of dental implant clinical experience on the accuracy of robot-assisted immediate implant placement: an in vitro study.

OBJECTIVES: To assess the accuracy and effectiveness among operators with different levels of experience in a robot-assisted immediate implant surgery. MATERIALS AND METHODS: The study included four participants who had received dental training at the same institution but have varying levels of clinical experience in implant dentistry, denoted as undergraduate student (UG), dental resident (DR), specialist with no robot experience (IS) and specialist with robot experience (RS). Following comprehensive theoretical training in robot-assisted implant operation, each operator participated in five robotic-assisted implant procedures at 21 sites, resulting in the implant surgery of a total of 20 implants. Subsequently, the accuracy of the implants was assessed by analyzing the preoperative planning and the postoperative CBCT scans, and the time required for each procedure was also recorded. RESULTS: Angular deviation in UG, DR, IS and RS group was 0.82 ± 0.27°, 0.55 ± 0.27°, 0.83 ± 0.27°, and 0.56 ± 0.36°, respectively. The total deviation of the implant platform point was 0.28 ± 0.10 mm, 0.26 ± 0.16 mm, 0.34 ± 0.08 mm and 0.31 ± 0.06 mm, respectively. The total deviation of the apical point was 0.30 ± 0.08 mm, 0.25 ± 0.18 mm, 0.31 ± 0.09 mm, and 0.31 ± 0.05 mm, respectively. The time spent was 10.37 ± 0.57 min, 10.56 ± 1.77 min, 9.93 ± 0.78 min, and 11.76 ± 0.78 min for each operator. As the number of operations increased, the operation time decreased, but there was no significant difference in implant accuracy between the different groups. CONCLUSIONS: Within the scope of this study, robot-assisted implant surgery demonstrated high accuracy, with no significant differences in performance between operators with varying levels of clinical experience or implant robot-user experience. Furthermore, the learning curve for robotic implant surgery is steep and consistent. CLINICAL RELEVANCE: Robot-assisted implant surgery demonstrates consistent high accuracy across operators of varying clinical and robotic experience levels, highlighting its potential to standardize procedures and enhance predictability in clinical outcomes.

The impact of photobiomodulation on angiogenic differentiation of two different dental derived stem cells using two irradiation protocols: an in vitro investigation.

The present study aimed to compare the effect of photobiomodulation with different energy densities on the angiogenic differentiation of human periodontal ligament stem cells (hPDLSCs) and stem cells from human exfoliated deciduous teeth (SHED). Photobiomodulation therapy with a 660 nm diode laser (2.4 J/cm2 and 3.9 J/cm2) on two consecutive days post-culture was applied to two types of stem cells (hPDLSCs and SHED). The Quantitative Real-time Polymerase Chain Reaction (RT-qPCR) test was undertaken to investigate Vascular Endothelial Growth Factor-A (VEGF-A) and Angiopoietin I (ANG-I) genes on days 1, 3, 5, 7, and 10 after the first session of laser application. The 4',6-diamidino-2-phenylindole (DAPI) staining and Methyl Thiazolyl Tetrazolium (MTT) test were conducted on days 1, 3, and 5 after the first session of laser application, to assess the cell viability. The Two-way ANOVA with Tukey post hoc test was used to analyze the outcomes of the MTT and RT-qPCR tests. The results of the MTT and DAPI convergently illustrated that the groups receiving photobiomodulation with 2.4 J/cm2 had higher cell viability compared to 3.9 J/cm2. All experimental groups showed an upregulation of VEGF-A and ANG-I gene expression from day 1 to 5, followed by a downregulation from day 5 to 10. The groups with cultured hPDLSCs and SHED receiving photobiomodulation using 2.4 J/cm2 had the most amounts of VEGF-A and ANG-I gene expression on day 5, respectively. In conclusion, the 660 nm mediated photobiomodulation therapy of cultured SHED and hPDLSCs with 2.4 J/cm2 energy density may be associated with higher angiogenic differentiation (the expression of VEGF-A and ANG-I) as well as higher cell viability compared to the photobiomodulation therapy with 3.9 J/cm2.

Fracture resistance and fractographic analysis of pressable glass-ceramics with different partial coverage designs for maxillary premolars.

BACKGROUND: Partial coverage concepts have met the main goal of conservative dentistry. Vonlays, which combine features of veneers and onlays, are a recent alternative to full coverage designs and overlay partial coverage restorations. This in vitro study was conducted to compare the fracture resistance of the newly introduced pressable zirconia-reinforced lithium silicate with pressable lithium disilicate ceramic and to determine the optimal preparation design for partial coverage on upper premolars. METHODS: Fifty-two duplicated epoxy resin dies were prepared following vonlay and overlay preparation guidelines. For each preparation (n = 26), the specimens were divided into two subgroups to be restored with lithium disilicate (IPS e.max Press) or zirconia-reinforced lithium silicate (Vita Ambria) (n = 13 each). Ceramic vonlays and overlays were bonded using dual cure resin cement, subjected to thermomechanical fatigue, and the load to fracture was tested by using a universal testing machine. The specimens were fractographically analyzed via scanning electron microscopy (SEM). The normality of the fracture resistance data was checked using the Shapiro‒Wilk test and Q‒Q plots, and two-way ANOVA was used to assess the effect of the type of preparation and ceramic material on the fracture resistance. RESULTS: The group of overlays restored with zirconia-reinforced lithium silicate showed the highest mean fracture load (1218.69 N), while the group of vonlays restored with lithium disilicate had the lowest mean fracture resistance (967.15 N). The effect of preparation design and material type on fracture resistance was significant for both factors, p = 0.003 and p < 0.0001, respectively. Different features of the fracture surfaces, such as arrest lines, hackles, and directions of crack propagation, were observed. CONCLUSIONS: Zirconia-reinforced lithium silicate exhibited greater resistance to fracture compared to lithium disilicate, making it a potential substitute for partial coverage restorations. Additionally, the overlay showed superior fracture resistance when compared to the vonlay preparation design.

The wettability of complete denture base materials constructed by conventional versus digital techniques: an in-vitro study.

BACKGROUND: Decreased salivary flow can make the patients uncomfortable with their complete dentures and affects the retention of the dentures. Milling and 3D printing have become an alternative to conventional denture construction techniques. The goal of this study was to evaluate the effect of conventional and digital techniques of the complete denture construction on the denture surface wettability with distilled water and saliva substitute before and after thermocycling. METHODS: A total of 30 specimens were utilized in the present study. Specimens were divided according to the construction techniques into 3 groups (n = 10 each). Group I: Heat-polymerized polymethylmethacrylate (PMMA) group, group II: Milled group, and group III: 3-dimensional (3D)-printed group. All the specimens were subjected to 2000 cycles of thermal aging in a thermocycler. The wettability of all specimens to water and saliva substitute was measured via a contact angle goniometer (Olympus TGHM, Rame-hart Inc, USA) before and after thermocycling. Descriptive statistical analysis, plots, and the Shapiro-Wilk test were used to verify normality for each variable. One-way ANOVA was used to compare the 3 study groups, while paired samples t-test was used to compare the differences within each group (P < .05). RESULTS: The smallest contact angle of drop of water to the denture base specimens before and after thermocycling were recorded in the milled group (53.0 ± 4.77 and 50.27 ± 2.30, respectively), followed by the heat polymerized PMMA group (85.65 ± 4.71 and 65.06 ± 2.27, respectively), and the 3D-printed group (91.34 ± 6.74 and 90.86 ± 8.57, respectively). While the smallest contact angle of drop of saliva substitute to denture base specimens was recorded in the milled group (56.82 ± 2.29 and 34.85 ± 7.51, respectively), followed by the 3D-printed group (72.87 ± 4.83 and 58.14 ± 9.58, respectively) and the heat polymerized PMMA group (83.62 ± 4.12 and 67.82 ± 4.93, respectively). There was statistically significant difference between the groups (P < .05). A significant decline in the average contact angle of drop of saliva has been reported in all groups after thermocycling. The contact angle values differed significantly between saliva substitute and distilled water in both 3D-printed and milled groups after thermocycling (P < .001). CONCLUSIONS: The milled denture base material presented the best wettability to water and saliva substitute than the 3D-printed and the heat-polymerized PMMA materials. Saliva substitutes improve the wetting ability of denture base materials manufactured by CAD/CAM compared with water.

Evaluation of apically extruded debris during root canal filling material removal in teeth with external apical root resorption: a comparison of different obturation techniques.

BACKGROUND: Root canal retreatment is necessary when initial treatment fails. Nickel-titanium systems help remove filling materials; however, some methods can cause canal content extrusion, resulting in inflammation and delayed healing. This study aimed to examine the impact of different preparation techniques and endodontic file systems on apical debris volume to limit material dispersion to periradicular tissues. METHODS: Ninety extracted maxillary incisors were evaluated. Simulated apical root resorption was created by removing the apical 2 mm of the root. The teeth were divided into two groups: one filled with a single cone and the other with cold lateral compaction (CLC). Each group was further divided into three subgroups (n = 15 each): Subgroup 1 used Reciproc R25 for removal and R50 for final preparation; Subgroup 2 used ProTaper Universal Retreatment (PTUR) files D1, D2, and D3 for removal and ProTaper Next X5 for finalization; and Subgroup 3 used VDW.Rotate Retreatment (VDW.RotateR) for removal and VDW.Rotate 50.04 for completion. Debris from retreatment was collected in pre-weighed tubes to determine the amount. The apical extrusion data underwent a two-way analysis of variance. RESULTS: The Reciproc group had a mean extruded debris weight of 0.54 ± 0.24 mg, higher than the PTUR (0.28 ± 0.15 mg) and VDW.RotateR (0.39 ± 0.29 mg) groups (p < 0.05). The single-cone technique (SCT) resulted in a mean debris weight of 0.34 ± 0.23 mg, lower than the CLC technique, which had a mean of 0.46 ± 0.27 mg (p < 0.05). SCT had a shorter retreatment duration (111.12 ± 33.46 s) compared to CLC (176.26 ± 52.26 s) (p < 0.05). CONCLUSION: The Reciproc file system and the CLC obturation technique resulted in greater apical debris extrusion than the other methods. SCT was quicker than CLC. The Reciproc groups are more susceptible to apex extrusion during retreatment.

Internal fit and marginal adaptation of all-ceramic implant-supported hybrid abutment crowns with custom-milled screw-channels on Titanium-base: in-vitro study.

BACKGROUND: Advancements in digital dentistry helped in custom-milling screw-channels in implant-supported restorations; however, the fit of these restorations is still unclear especially for contemporary computer aided designing/computer aided manufacturing (CAD/CAM) materials. This study aimed to compare the internal and marginal fit of Ultra translucent multilayered zirconia versus lithium disilicate implant-supported hybrid abutment crowns (HACs) constructed with custom-milled screw-channels on Titanium-base. MATERIALS AND METHODS: A total of 24 HACs with custom-milled screw-channels were constructed from lithium disilicate (Group LDS) and Ultra translucent multilayered zirconia (Group UT) using digital workflow (n = 12). The internal and marginal gaps of HACs on their corresponding Titanium-bases were assessed using replica technique and stereomicroscope, respectively. After testing for normality, quantitative data were expressed as mean and standard deviation and compared using independent t-test at a level of significance (P ≤ 0.05). RESULTS: There was no statistically significant difference between Group LDS and Group UT in terms of marginal and internal fit. The internal and marginal gaps in both groups were within the accepted values reported in literature. CONCLUSIONS: UT and LDS HACs with custom-milled screw-channels demonstrated comparable and acceptable internal fit and marginal adaptations to Ti-base, which lied within the range reported in literature.

Marginal adaptation of customized gutta percha cone with calcium silicate based sealer versus MTA and biodentine apical plugs in simulated immature permanent teeth (an in vitro study).

BACKGROUND: This study aimed to compare the marginal adaptation of a single customized gutta percha cone with calcium silicate-based sealer versus mineral trioxide aggregate (MTA) and Biodentine apical plugs in simulated immature permanent teeth. METHODS: Thirty-nine extracted human maxillary anterior teeth were selected, prepared to simulate immature permanent teeth with an apical diameter 1.1 mm, placed in moist foam and divided into three groups. Group 1: Obturation with a single customized gutta percha cone and calcium silicate sealer. Group 2: MTA apical plug. Group 3: Biodentine apical plug. After incubation, teeth were horizontally sectioned at 1 mm and 3 mm from the apex and marginal adaptation was evaluated using scanning electron microscope (SEM). RESULTS: Biodentine showed the least mean gap size at both 1 and 3 mm from the apex with no statistically significant differences compared to MTA (p > 0.05). The single customized cone with calcium silicate based sealer showed the greatest mean gap size at both 1 and 3 mm from the apex with a statistically significant difference compared to the other groups (p < 0.001). CONCLUSION: Biodentine and MTA apical plugs provide a significantly better marginal adaptation to the dentinal walls than a single customized gutta percha cone with calcium silicate based sealer in simulated immature permanent teeth.

The effect of two preparation designs on the fracture resistance and marginal adaptation of two types of ceramic crowns using CAD/CAM technology (In vitro study).

BACKGROUND: Recently, prosthodontic approaches involve more conservative procedures that include less invasive finish line preparations that use less ceramic thickness. AIM OF THE STUDY: This in vitro study aimed to evaluate the effect of vertical preparation and modified vertical preparation designs on the marginal adaptation and fracture resistance of two types of ceramic crowns using CAD/CAM technology. MATERIALS AND METHODS: Two typodont maxillary first premolars were embedded in acrylic resin. Forty positive replicas of epoxy resin dies were used that were divided into two groups depending on the preparation design (n = 20); Group V (Vertical): dies with feather edge finish line and Group MV (Modified vertical): dies with feather edge finish line, where a reverse shoulder of 1 mm depth was placed on the buccal surface 1.5 mm from the occlusal surface. Each group was further subdivided into two subgroups according to the type of ceramic material (n = 10): Subgroup Va and subgroup MVa for lithium disilicate (e.max CAD) and subgroup Vb and subgroup MVb for zirconia (zolid ht+). Crown restorations were made with CAD-CAM technology. The marginal adaptation was assessed using a stereomicroscope both prior to cementation and after cementation and aging. Fracture resistance was tested with a universal testing machine, and the data were statistically analyzed. RESULTS: Marginal adaptation showed no significant differences between subgroups before or after cementation and aging. Three-way ANOVA indicated that preparation design (p = 0.516) and material (p = 0.269) had no significant effect, but cementation had a significant effect (p < 0.0001) on the marginal adaptation. According to two-way ANOVA test, Subgroup (MVb) showed the highest result followed by subgroup (Vb) and subgroub (MVa) and the least was subgroub (Va). Fracture modes showed no significant differences among the subgroups (p = 0.982). CONCLUSIONS: Marginal adaptation of lithium disilicate and zirconia crowns remained clinically acceptable regardless of preparation design. While the modified vertical preparation with a reverse shoulder notably enhanced the fracture resistance of both materials, with zirconia demonstrating superior fracture resistance compared to lithium disilicate with average values exceeding premolar biting force.

Effect of polishing process on torque loss ratio and microgap of selective laser melting abutment: an in vitro study.

BACKGROUND: The purpose of this in vitro study was to investigate the effect of polishing post-treatment process on the torque loss ratio and microgap of Selective Laser Melting (SLM) abutments before and after mechanical cycling test through improving the surface roughness of the implant-abutment interface. MATERIALS AND METHODS: Forty SLM abutments were fabricated, with 20 underwent minor back-cutting, designated as polishing, in the implant-abutment interface. The abutments were divided into three groups: SLM abutments (group A), original abutments (group B), and polished SLM abutments (group C), each containing 20 abutments. Surface roughness was evaluated using a laser microscope. Implant-abutment specimens were subjected to mechanical cycling test, and disassembly torque values were measured before and after. Scanning electron microscope (SEM) was used to measure microgap after longitudinal sectioning of specimens. Correlation between surface roughness, torque loss ratio, and microgap were evaluated. LSD's test and Tamhane's T2 comparison were used to analyze the data (α = 0.05). RESULTS: The Sz value of polished SLM abutments (6.86 ± 0.64 µm) demonstrated a significant reduction compared to SLM abutments (26.52 ± 7.12 µm). The torque loss ratio of polished SLM abutments (24.16%) was significantly lower than SLM abutments (58.26%), while no statistically significant difference that original abutments (18.23%). The implant-abutment microgap of polished SLM abutments (2.38 ± 1.39 µm) was significantly lower than SLM abutments (8.69 ± 5.30 µm), and this difference was not statistically significant with original abutments (1.87 ± 0.81 µm). A significant positive correlation was identified between Sz values and the ratio of torque loss after cycling test (r = 0.903, P < 0.01), as well as Sz values and the microgap for all specimens in SLM abutments and polished SLM abutments (r = 0.800, P < 0.01). CONCLUSION: The findings of this study indicated that the polishing step of minor back-cutting can lead to a notable improvement in the roughness of SLM abutments interface, which subsequently optimized the implant-abutment fit. It can be seen that the application of minor back-cutting method has advanced the clinical use of SLM abutments.

Characteristics of lung resistance and elastance associated with tracheal stenosis and intrapulmonary airway narrowing in ex vivo sheep lungs.

BACKGROUND: Understanding the characteristics of pulmonary resistance and elastance in relation to the location of airway narrowing, e.g., tracheal stenosis vs. intrapulmonary airway obstruction, will help us understand lung function characteristics and mechanisms related to different airway diseases. METHODS: In this study, we used ex vivo sheep lungs as a model to measure lung resistance and elastance across a range of transpulmonary pressures (5-30 cmH2O) and ventilation frequencies (0.125-2 Hz). We established two tracheal stenosis models by inserting plastic tubes into the tracheas, representing mild (71.8% lumen area reduction) and severe (92.1%) obstructions. For intrapulmonary airway obstruction, we induced airway narrowing by challenging the lung with acetylcholine (ACh). RESULTS: We found a pattern change in the lung resistance and apparent lung elastance as functions of ventilation frequency that depended on the transpulmonary pressure (or lung volume). At a transpulmonary pressure of 10 cmH2O, lung resistance increased with ventilation frequency in severe tracheal stenosis, whereas in ACh-induced airway narrowing the opposite occurred. Furthermore, apparent lung elastance at 10 cmH2O decreased with increasing ventilation frequency in severe tracheal stenosis whereas in ACh-induced airway narrowing the opposite occurred. Flow-volume analysis revealed that the flow amplitude was much sensitive to ventilation frequency in tracheal stenosis than it was in ACh induced airway constriction. CONCLUSIONS: Results from this study suggest that lung resistance and apparent elastance measured at 10 cmH2O over the frequency range of 0.125-2 Hz can differentiate tracheal stenosis vs. intrapulmonary airway narrowing in ex vivo sheep lungs.

Cyclic fatigue resistance of two pediatric rotary files manufactured with different heat treatments: an in-vitro study.

Nickel-titanium (NiTi) instruments offer many advantages during endodontic instrumentation; however, the fracture risk within the canal remains a concern. Manufacturers continuously develop and introduce instruments to the market with supposedly enhanced cyclic fatigue resistance and increased flexibility, achieved through different proprietary manufacturing processes, the details of which have not been made public. In recent years, two rotary systems specially designed for deciduous teeth have been commercially available, but information about their performance is lacking. This investigation aimed to identify which manufacturing process provides better cyclic fatigue resistance: the AF-H Wire technology used in the AF baby rotary files (AF-f) or the CM-Wire technology used in the i3 Gold deciduous teeth rotary files (i3G-f). Forty rotary International Organization for Standardization (ISO) 25/04 files were tested in artificial canals with a standard geometry of 60° angle and 2.5 mm radius until fracture. The number of cycles to fracture was calculated, and the length of the fragments was measured. A scanning electron microscope (SEM) was used to examine the fracture surfaces and fragments. Energy dispersive spectroscopy (EDS) was used to determine the percentage weight of NiTi in each file. The statistical analysis (Mann-Whitney test) showed that the cyclic fatigue resistance of the AF-f was significantly higher (p < 0.0001) than that of the i3G-f. Additionally, there was a significant difference (p = 0.0419) in the length of the fractured fragments. All instruments showed one or more types of manufacturing defects and presented similar NiTi percentages by weight. The manufacturing process is critical to cyclic fatigue resistance, and there seems to be responsible for the difference in cyclic fatigue resistance between these similar instruments.

Comparative evaluation of clinical efficacy and volumetric changes in pulpectomized primary molars using hand K-file, ProTaper rotary file, and Kedo-SG blue file: an in-vitro cone beam computed tomography analysis.

The accomplishment of a successful pulpectomy depends on multiple factors that involve targeted removal of the causative irritants and soft and hard tissue debris by mechanical and chemical means. Compare and evaluate the efficacy of canal preparation and volumetric filling using conventional files and two rotary file systems using cone beam computed tomography (CBCT). Thirty freshly extracted human primary second molars were randomly divided into three groups of 10 teeth each. After access opening and working length determination, pre-operative volume analysis was done using CBCT. The canals were then instrumented by either hand K-files, ProTaper rotary files or Kedo-SG Blue rotary files. Post-operative volume analysis was performed using CBCT. All the canals were obturated using Metapex and scanned again using CBCT. Mean values of the pre- and post-operative canal volumes were analyzed using one-way Analysis of Variance (ANOVA). Inter- and intra-group volumetric changes were analyzed statistically using a post hoc test. The mean difference in volume after canal preparation and obturation was the highest in the Kedo-SG Blue group, followed by the ProTaper group and the least in the hand K group (p = 0.001). Inter-group comparison showed statistically significant differences between the hand K group and ProTaper group (p = 0.001), the ProTaper group and Kedo-SG Blue group (p = 0.001), and the hand-K group and Kedo-SG Blue group (p = 0.02). The volume of preparation and obturation was the highest using Kedo-SG Blue, followed by the ProTaper file systems.

Retention of implant retained obturator using two implant placement configurations for maxillectomy cases: in-vitro study.

BACKGROUND: Implant-retained obturators for maxillectomy cases have several advantages over traditional obturators but prosthetic design for specific conditions after maxillary resection has several challenges and the appropriate implant placement configuration is essential for improving retention and the stability of the implant-retained obturator. OBJECTIVES: The present study aimed to assess the retention force of using linear and nonlinear implant placement configurations using ball and socket attachment in implant-retained obturators at the initial retention and after simulation of six months of use. MATERIALS AND METHODS: Two identical epoxy resin maxillary models of a completely edentulous unilateral maxillary defect (Brown's class IIb) were used for implant placement, in the first model three implants were arranged with linear placement configuration, and in the second model three implants were arranged in nonlinear placement configuration. For proper sample sizing, 26 models and obturator were used. Two equal groups of obturators (13 for each group) were constructed, each with a different implant placement configuration. Both groups used the same attachment design (a non-splinted ball attachment). Using a cyclic loading machine that served as a dental insertion and removal simulator, each study group was subjected to 500 tension-compression cycles simulating 6 months of use. Using the universal testing machine, each obturator was removed at a speed of 50 mm/min for the crosshead. peak load to dislodgement was measured at the initial retention and after the simulations of six months of use. Data were analyzed using independent and paired t-tests while percent change was analyzed using the Mann Whitney U test. RESULTS: There were a statistically significant differences in retention between the nonlinear implant placement configuration for Brown's class IIb maxillectomy and the linear implant placement configuration at initial retention evaluation with p-value of < 0.0001 and after simulation of six months of usage with p-value of < 0.0001 Also, after simulation of 6 months of use group I lose - 24.87 (10.16) % of its retention while group II lose - 17.49 (7.78) %. CONCLUSIONS: Non-linear implant placement is more retentive at the initial retention and after simulation of six months of use than linear and loses less retention after usage.

Effect of glide path preparation on the apical debris extrusion for three single-file systems.

BACKGROUND: The dentinal debris produced during root canal preparation can be extruded through the apical foramen, which may cause undesired consequences, such as the postoperative inflammation of periapical tissues. OBJECTIVES: The aim of the present in vitro study was to evaluate the effect of glide path preparation on apical debris extrusion for the Reciproc®, WaveOne Gold® and One Curve file systems. MATERIAL AND METHODS: A total of 72 mandibular incisors were divided into 6 groups according to the nickel-titanium (NiTi) system used and glide path preparation: group Rp - Reciproc; group Rp-O - Reciproc after glide path preparation; group WG - WaveOne Gold; group WG-O - WaveOne Gold after glide path preparation; group OC - One Curve; and group OC-O - One Curve after glide path preparation. The preand post-instrumentation weight of Eppendorf tubes was measured. The pre-weight was subtracted from the post-weight to calculate the amount of apically extruded debris. The data was analyzed using the one-way analysis of variance (ANOVA) with the statistical program PASW Statistics for Windows, v.18.0. RESULTS: No statistically significant differences were found between the single-NiTi file systems with different kinematics in terms of apical debris extrusion, with or without glide path preparation (p > 0.05). CONCLUSIONS: The amount of apically extruded debris was not affected by the kinematics of different single-NiTi file systems. Moreover, creating a glide path had no effect on the apically extruded debris in straight root canals.

Evaluating the accuracy of CEREC intraoral scanners for inlay restorations: impact of adjacent tooth materials.

BACKGROUND: The accuracy of intraoral scanning is critical for computer-aided design/computer-aided manufacturing workflows in dentistry. However, data regarding the scanning accuracy of various adjacent restorative materials and intraoral scanners are lacking. This in vitro study aimed to evaluate the effect of adjacent restorative material type and CEREC's intraoral scanners on the accuracy of intraoral digital impressions for inlay cavities. METHODS: The artificial tooth was prepared with an occlusal cavity depth of 2 mm, a proximal box width at the gingival floor of 1.5 mm, and an equi-gingival margin extended disto-occlusally at the transition line angle on both the lingual and buccal sides for an inlay restoration. The adjacent teeth were veneered with crowns made of gold and zirconia, and an artificial tooth (resin) was utilized as the control group. The inlay cavity and adjacent teeth (Gold, Zirconia, and resin) were scanned 10 times using Chairside Economical Restoration of Esthetic Ceramics (CEREC) Primescan (PS), Omnicam (OC), and Bluecam (BC). A reference scan was obtained using a laboratory scanner (3-shape E3). Scanning was performed according to the manufacturer's instructions, including powder application for the BC group. Standard tesselation language files were analyzed using a three-dimensional analysis software program. Experimental data were analyzed using a two-way analysis of variance and the Tukey's post-hoc comparison test. RESULTS: The restorative materials of the adjacent teeth significantly affected the accuracy of the intraoral digital impressions (p < .05). The zirconia group exhibited the highest trueness deviation, followed by the resin and gold groups, with each demonstrating a statistically significant difference (p < .05). The resin group demonstrated the highest maximum positive deviation and deviation in precision. Gold exhibited the lowest average deviation value for trueness compared with those of the other adjacent restorative materials. Intraoral scanner type significantly influenced the trueness and precision of the scan data (p < .05). The average deviation of trueness according to the intraoral scanner type increased in the following order: BC > PS > OC. The average deviation in precision increased in the following order: PS>OC>BC (p < .05). CONCLUSION: The restorative materials of the adjacent tooth and the type of intraoral scanner affect the accuracy of the intraoral digital impression. The trueness of the digital images of the BC group, obtained by spraying the powder, was comparable to that of the PS group. Among the adjacent restorative materials, zirconia exhibited the lowest trueness. In contrast, PS demonstrated the highest precision among the intraoral scanners, while resin displayed the lowest precision among the adjacent restorative materials.

Metformin reduced the alkaline resistance of Enterococcus faecalis against calcium hydroxide via Man-PTS EII: in vitro and in vivo studies.

OBJECTIVES: The mannose phosphotransferase system (Man-PTS) plays crucial roles in the adaptive metabolic activity of Enterococcus faecalis (E. faecalis) in adverse environments. The aim of this study was to evaluate the role of Man-PTS in the alkaline resistance of E. faecalis against calcium hydroxide (CH) and the effect of metformin (Met) on the alkaline resistance of E. faecalis to CH. MATERIALS AND METHODS: The regulatory role of Man-PTS EII in the alkaline resistance of E. faecalis was firstly investigated using a wild-type highly alkaline-resistant E. faecalis XS 003, standard ATCC 29212 and Man-PTS EIID gene deficient (△mptD) and overexpressing (+mptD) strains of E. faecalis. RNA sequencing of Met-treated E. faecalis was performed to further validate the effect of Met on Man-PTS. The effect of Met on CH resistance of E. faecalis was verified by evaluating the survival, membrane potential and permeability, intracellular pH and ATP, and the expression of Man-PTS EII and membrane transporter-related genes of E. faecalis. The effect of Met on the ability of CH to remove E. faecalis biofilm on the dentin surface was also tested. The in vivo therapeutic effect of Met plus CH (CHM) was further investigated in a rat apical periodontitis model induced by E. faecalis XS 003. RESULTS: Man-PTS EII significantly promoted the survival ability of E. faecalis in CH and enhanced its resistance to CH. The inhibition of Man-PTS EII by Met resulted in reduced alkaline resistance of E. faecalis in the presence of CH, while also enhancing the antimicrobial properties of CH against E. faecalis biofilm on dentin. Additionally, Met plus CH showed the synergistically promoted intra-canal E. faecalis infection control and healing of periapical lesion in rats. CONCLUSIONS: Met could significantly reduce the alkaline resistance of E. faecalis against CH through the modulation of Man-PTS EII, and improved the antibacterial effect of CH against E. faecalis infection both in vitro and in vivo. CLINICAL RELEVANCE: Met could significantly enhance the ability of CH to control E. faecalis infection through reducing the alkaline resistance of E. faecalis.

Evaluation of pulp tissue dissolving efficiency of sodium and calcium hypochlorite solutions activated by ultrasonics and laser: an in vitro study.

OBJECTIVES: This study aimed to compare the tissue dissolving capacities of sodium and calcium hypochlorite [NaOCl and Ca(OCl)2] solutions applied without activation or with two irrigant activation methods. MATERIALS AND METHODS: One hundred and eight dentin cavities were prepared. Preweighed tissue pieces were placed in these dentin cavities, and samples were divided into nine groups of twelve. In groups 1, 2, and 3, NaOCl was used with non-activation (NA), passive ultrasonic (PUA), and laser activation (LA). With the same techniques, Ca(OCl)2 was used in groups 4, 5, and 6, and distilled water was used in groups 7, 8, and 9. The weight loss of tissue samples was calculated and analyzed using Two-way ANOVA and Duncan tests. RESULTS: Distilled water groups showed no tissue dissolution in any conditions. NaOCI and Ca(OCI)2 showed statistically similar dissolving effectiveness when used with the same technique. Activated groups dissolved significantly greater tissue than non-activated ones, the highest in LA. CONCLUSIONS: Ca(OCI)2 can be an alternative to NaOCl; for both, the first choice of activation may be the LA.

Effect of temperature on rehydration and fracture resistance of reattached tooth fragments after crown fracture: An in vitro study.

BACKGROUND: Uncomplicated crown fractures of maxillary anterior teeth are common dental injuries, and the bonding of fractured fragments is recommended for management. Rehydration of fragments improves bonding and fracture resistance. Therefore, the aim of this study was to compare the fracture resistance of the reattached tooth fragment of the incisor crown after rehydration using either a steamer or a humidifier. MATERIALS AND METHODS: Bovine teeth were used as a model. Fractured fragments were divided into three groups: Group I (no rehydration), Group II (rehydration by humidifier), and Group III (rehydration by steamer). Fragments were reattached using a standard bonding protocol. Fracture resistance was tested using a universal testing machine. Statistical analysis was performed using analysis of variance and Chi-square tests. RESULTS: The force required to fracture the reattached fragments was significantly higher in Group II (humidifier) compared to Group I (no rehydration) (P = 0.005). Group III (steamer) had a force value similar to Group I, indicating no significant improvement in fracture resistance with steamer rehydration. The temperature inside the steam-based chamber reached an average of 95.7°C with 95% humidity, whereas the conventional humidification chamber had an average temperature of 39.2°C and 84% humidity. CONCLUSION: Within the limitations of the present study, the rehydration protocol using a steam-based chamber was found to have a significantly lower force required to fracture the reattached fragments as compared to humidifier-based chamber. This was not significantly different from the fragments which were reattached without rehydration.