RESUMEN
A major advantage of surgical robots is that they can reduce the invasiveness of a procedure by enabling the clinician to manipulate tools as they would in open surgery but through small incisions in the body. Neurosurgery has yet to benefit from this advantage. Although clinical robots are available for the least invasive neurosurgical procedures, such as guiding electrode insertion, the most invasive brain surgeries, such as tumor resection, are still performed as open manual procedures. To investigate whether robotics could reduce the invasiveness of major brain surgeries while still providing the manipulation capabilities of open surgery, we created a two-armed joystick-controlled endoscopic robot. To evaluate the efficacy of this robot, we developed a set of neurosurgical skill tasks patterned after the steps of brain tumor resection. We also created a patient-derived brain model for pineal tumors, which are located in the center of the brain and are normally removed by open surgery. In comparison, testing with existing manual endoscopic instrumentation, we found that the robot provided access to a much larger working volume at the trocar tip and enabled bimanual tasks without compression of brain tissue adjacent to the trocar. Furthermore, many tasks could be completed faster with the robot. These results suggest that robotics has the potential to substantially reduce the invasiveness of brain surgery by enabling certain procedures currently performed as open surgery to be converted to endoscopic interventions.
Asunto(s)
Robótica , Humanos , Neurocirujanos , Extremidad Superior , Mano , EndoscopiosRESUMEN
OBJECTIVES: We sought to develop an ex vivo trachea model capable of producing mild, moderate, and severe tracheobronchomalacia for optimizing airway stent design. We also aimed to determine the amount of cartilage resection required for achieving different tracheobronchomalacia grades that can be used in animal models. METHODS: We developed an ex vivo trachea test system that enabled video-based measurement of internal cross-sectional area as intratracheal pressure was cyclically varied for peak negative pressures of 20 to 80 cm H2O. Fresh ovine tracheas were induced with tracheobronchomalacia by single mid-anterior incision (n = 4), mid-anterior circumferential cartilage resection of 25% (n = 4), and 50% per cartilage ring (n = 4) along an approximately 3-cm length. Intact tracheas (n = 4) were used as control. All experimental tracheas were mounted and experimentally evaluated. In addition, helical stents of 2 different pitches (6 mm and 12 mm) and wire diameters (0.52 mm and 0.6 mm) were tested in tracheas with 25% (n = 3) and 50% (n = 3) circumferentially resected cartilage rings. The percentage collapse in tracheal cross-sectional area was calculated from the recorded video contours for each experiment. RESULTS: Ex vivo tracheas compromised by single incision and 25% and 50% circumferential cartilage resection produce tracheal collapse corresponding to clinical grades of mild, moderate, and severe tracheobronchomalacia, respectively. A single anterior cartilage incision produces saber-sheath type tracheobronchomalacia, whereas 25% and 50% circumferential cartilage resection produce circumferential tracheobronchomalacia. Stent testing enabled the selection of stent design parameters such that airway collapse associated with moderate and severe tracheobronchomalacia could be reduced to conform to, but not exceed, that of intact tracheas (12-mm pitch, 0.6-mm wire diameter). CONCLUSIONS: The ex vivo trachea model is a robust platform that enables systematic study and treatment of different grades and morphologies of airway collapse and tracheobronchomalacia. It is a novel tool for optimization of stent design before advancing to in vivo animal models.
Asunto(s)
Broncoscopía , Traqueobroncomalacia , Ovinos , Animales , Traqueobroncomalacia/diagnóstico , Traqueobroncomalacia/cirugía , Tráquea/cirugía , Stents , Modelos AnimalesRESUMEN
Intraoperative MRI has been increasingly used to robotically deliver electrodes and catheters into the human brain using a linear trajectory with great clinical success. Current cranial MR guided robotics do not allow for continuous real-time imaging during the procedure because most surgical instruments are not MR-conditional. MRI guided robotic cranial surgery can achieve its full potential if all the traditional advantages of robotics (such as tremor-filtering, precision motion scaling, etc.) can be incorporated with the neurosurgeon physically present in the MRI bore or working remotely through controlled robotic arms. The technological limitations of design optimization, choice of sensing, kinematic modeling, physical constraints, and real-time control had hampered early developments in this emerging field, but continued research and development in these areas over time has granted neurosurgeons far greater confidence in using cranial robotic techniques. This article elucidates the role of MR-guided robotic procedures using clinical devices like NeuroBlate and Clearpoint that have several thousands of cases operated in a "linear cranial trajectory" and planned clinical trials, such as LAANTERN for MR guided robotics in cranial neurosurgery using LITT and MR-guided putaminal delivery of AAV2 GDNF in Parkinson's disease. The next logical improvisation would be a steerable curvilinear trajectory in cranial robotics with added DOFs and distal tip dexterity to the neurosurgical tools. Similarly, the novel concept of robotic actuators that are powered, imaged, and controlled by the MRI itself is discussed in this article, with its potential for seamless cranial neurosurgery.
Asunto(s)
Neurocirugia , Procedimientos Quirúrgicos Robotizados , Robótica , Humanos , Procedimientos Neuroquirúrgicos/métodos , Procedimientos Quirúrgicos Robotizados/métodos , Imagen por Resonancia MagnéticaRESUMEN
Magnetic ball chains are well suited to serve as the steerable tips of endoluminal robots. While it has been demonstrated that these robots produce a larger reachable workspace than magnetic soft continuum robots designed using either distributed or lumped magnetic material, here we investigate the orientational capabilities of these robots. To increase the range of orientations that can be produced at each point in the workspace, we introduce a comparatively-stiff outer sheath from which the steerable ball chain is extended. We present an energy-based kinematic model and also derive an approximate expression for the range of achievable orientations at each point in the workspace. Experiments are used to validate these results.
RESUMEN
A hybrid continuum robot design is introduced that combines a proximal tendon-actuated section with a distal telescoping section comprised of permanent-magnet spheres actuated using an external magnet. While, individually, each section can approach a point in its workspace from one or at most several orientations, the two-section combination possesses a dexterous workspace. The paper describes kinematic modeling of the hybrid design and provides a description of the dexterous workspace. We present experimental validation which shows that a simplified kinematic model produces tip position mean and maximum errors of 3% and 7% of total robot length, respectively.
RESUMEN
Mechanics-based models have been developed to describe the shape of tendon-actuated continuum robots. Models have also been developed to describe the shape of concentric tube robots, i.e., nested combinations of precurved superelastic tubes. While an important class of continuum robots used in endoscopic and intracardiac medical applications combines these two designs, existing models do not cover this combination. Tendon-actuated models are limited to a single tube while concentric tube models do not include tendon-produced forces and moments. This paper derives a mechanics-based model for this hybrid design and assesses it using numerical and physical experiments involving a pair of tendon-actuated tubes. It is demonstrated that, similar to concentric tube robots, relative twisting between the tendon-actuated tubes is an important factor in determining overall robot shape.
RESUMEN
This paper introduces a novel class of hyperredundant robots comprised of chains of permanently magnetized spheres enclosed in a cylindrical polymer skin. With their shape controlled using an externally-applied magnetic field, the spherical joints of these robots enable them to bend to very small radii of curvature. These robots can be used as steerable tips for endoluminal instruments. A kinematic model is derived based on minimizing magnetic and elastic potential energy. Simulation is used to demonstrate the enhanced steerability of these robots in comparison to magnetic soft continuum robots designed using either distributed or lumped magnetic material. Experiments are included to validate the model and to demonstrate the steering capability of ball chain robots in bifurcating channels.
RESUMEN
This paper presents a novel continuum robot sheath for use in single-port minimally invasive procedures such as neuroendoscopy in which the sheath is designed to deliver multiple robotic arms. Actuation of the sheath is achieved by using precurved superelastic tubes lining the working channels used for arm delivery. These tubes perform a similar role to push/pull tendons, but can accomplish shape change of the sheath via rotation. A kinematic model using Cosserat rod theory is derived which is based on modeling the system as a set of eccentrically aligned precurved tubes constrained along their length by an elastic backbone. The specific case of a two-arm sheath is considered in detail. Simulation and experiments are used to investigate the validate the concept and model.
RESUMEN
Continuum robots are not constructed with discrete joints but, instead, change shape and position their tip by flexing along their entire length. Their narrow curvilinear shape makes them well suited to passing through body lumens, natural orifices, or small surgical incisions to perform minimally invasive procedures. Modeling and controlling these robots are, however, substantially more complex than traditional robots comprised of rigid links connected by discrete joints. Furthermore, there are many approaches to achieving robot flexure. Each presents its own design and modeling challenges, and to date, each has been pursued largely independently of the others. This article attempts to provide a unified summary of the state of the art of continuum robot architectures with respect to design for specific clinical applications. It also describes a unifying framework for modeling and controlling these systems while additionally explaining the elements unique to each architecture. The major research accomplishments are described for each topic and directions for the future progress needed to achieve widespread clinical use are identified.
RESUMEN
Soft robots can provide advantages for medical interventions given their low cost and their ability to change shape and safely apply forces to tissue. This article explores the potential for their use for endoscopically-guided balloon dilation procedures in the airways. A scalable robot design based on balloon catheter technology is proposed, which is composed of five balloons together with a tip-mounted camera and LED. Its design parameters are optimized with respect to the clinical requirements associated with balloon dilation procedures in the trachea and bronchi. Possessing a lumen to allow for respiration and powered by the pressure and vacuum sources found in a clinical procedure room, the robot is teleoperated through the airways using a game controller and real-time video from the tip-mounted camera. The robot design includes proximal and distal bracing balloons that expand radially to produce traction forces. The distal bracing balloon is also used to perform balloon dilation. Three actuation balloons, located between the bracing balloons, produce elongation and bending of the robot body to enable locomotion and turning. An analysis of the actuation balloons, which incorporate helical coils to prevent radial collapse, provides design formulas by relating geometric parameters to such performance criteria as maximum change in actuator length and maximum robot bending angle. Experimental evaluation of a prototype robot inside rigid plastic tubes and ex vivo porcine airways is used to demonstrate the potential of the approach.
Asunto(s)
Robótica , Porcinos , Animales , Robótica/métodos , Endoscopios , Cateterismo , Endoscopía , PlásticosRESUMEN
Robotics is a forward-looking discipline. Attention is focused on identifying the next grand challenges. In an applied field such as medical robotics, however, it is important to plan the future based on a clear understanding of what the research community has recently accomplished and where this work stands with respect to clinical needs and commercialization. This Review article identifies and analyzes the eight key research themes in medical robotics over the past decade. These thematic areas were identified using search criteria that identified the most highly cited papers of the decade. Our goal for this Review article is to provide an accessible way for readers to quickly appreciate some of the most exciting accomplishments in medical robotics over the past decade; for this reason, we have focused only on a small number of seminal papers in each thematic area. We hope that this article serves to foster an entrepreneurial spirit in researchers to reduce the widening gap between research and translation.
Asunto(s)
Procedimientos Quirúrgicos Robotizados , Robótica/tendencias , Investigación Biomédica Traslacional/tendencias , Historia del Siglo XXI , Humanos , Laparoscopía , Diseño de Prótesis , Publicaciones , Investigadores , Robótica/historia , Investigación Biomédica Traslacional/historiaRESUMEN
Like ready-to-wear clothing, medical devices come in a fixed set of sizes. While this may accommodate a large fraction of the patient population, others must either experience suboptimal results due to poor sizing or must do without the device. Although techniques have been proposed to fabricate patient-specific devices in advance of a procedure, this process is expensive and time consuming. An alternative solution that provides every patient with a tailored fit is to create devices that can be customized to the patient's anatomy as they are delivered. This paper reports an in vivo molding process in which a soft flexible photocurable stent is delivered into the trachea or bronchi over a UV-transparent balloon. The balloon is expanded such that the stent conforms to the varying cross-sectional shape of the airways. UV light is then delivered through the balloon curing the stent into its expanded conformal shape. The potential of this method is demonstrated using phantom, ex vivo and in vivo experiments. This approach can produce stents providing equivalent airway support to those made from standard materials while providing a customized fit.
RESUMEN
OBJECTIVES: We sought to demonstrate in an animal model that helical stents made from a nickel titanium alloy called nitinol (NiTi) and designed for malacic airways could be delivered and removed without significant trauma while minimally impeding mucus clearance during the period of implantation. METHODS: Stents were delivered and removed from the tracheas of healthy 20 kg swine (n = 5) using tools designed to minimize trauma. In 4-week experiments, the stents were implanted on day 0, removed after 3 weeks, and swine were put to death after 4 weeks. Weekly bronchoscopies, radiographs, and mucus clearance examinations were performed in vivo. Hematoxylin and eosin staining and scanning electron microscopy imaging were used to evaluate foreign body response, tracheal tissue reaction, and damage and to measure unciliated regions. RESULTS: In all in vivo experiments, the stent was implanted and removed atraumatically. Mucus clearance was maintained throughout the experiment period. Hematoxylin and eosin-stained slides showed that foreign body response and tracheal tissue damage were localized to the stented subsections. Tracheal tissue reaction and damage was further restricted to the epithelium and submucosal layers. Scanning electron microscopy imaging revealed that the cilia were absent only over the contact area between the trachea and the wire forming the helical stent. CONCLUSIONS: Helical nitinol stents designed to provide radial support for malacic airways were well tolerated in a porcine model, providing for mucus clearance while also enabling atraumatic removal.
RESUMEN
OBJECTIVE: The goal was to develop a pediatric airway stent for treating tracheobronchomalacia that could be used as an alternative to positive pressure ventilation. The design goals were for the stent to allow mucus flow and to resist migration inside the airways, while also enabling easy insertion and removal. METHODS: A helical stent design, together with insertion and removal tools, is presented. A mechanics model of stent compression is derived to assist in selecting stent design parameters (pitch and wire diameter) that provide the desired amount of tracheal support, while introducing the minimal amount of foreign material into the airway. Worst-case airway area reduction with stent support is investigated experimentally using a pressurized tracheal phantom matched to porcine tracheal tissue properties. The stent design is then evaluated in a porcine in vivo experiment. RESULTS: Phantom testing validated the mechanics model of stent compression. In vivo testing demonstrated that the stent was well tolerated by the animal. Since the helical design covers only a small portion of the epithelium, mucus transport through the stented region was minimally impeded. Furthermore, the screw-like stent resisted migration, while also providing for atraumatic removal through the use of an unscrewing motion during removal. CONCLUSION: The proposed stent design and tools represent a promising approach to prevent airway collapse in children with tracheobronchomalacia. SIGNIFICANCE: The proposed technology overcomes the limitations of existing airway stents and may provide an alternative to maintaining children on a ventilator.
Asunto(s)
Manejo de la Vía Aérea/instrumentación , Manejo de la Vía Aérea/métodos , Remoción de Dispositivos/métodos , Stents , Tráquea , Animales , Moco , Fantasmas de Imagen , Diseño de Prótesis , Porcinos , Tráquea/diagnóstico por imagen , Tráquea/fisiología , Tráquea/cirugía , Traqueobroncomalacia/terapiaRESUMEN
This paper presents a novel continuum robot sheath for use in single-port minimally invasive procedures such as neuroendoscopy in which the sheath is designed to deliver multiple robotic arms. Articulation of the sheath is achieved by using precurved superelastic tubes lining the working channels used for arm delivery. These tubes perform a similar role to push/pull tendons, but can accomplish shape change of the sheath via rotation as well as translation. A kinematic model using Cosserat rod theory is derived which is based on modeling the system as a set of eccentrically aligned precurved tubes constrained along their length by an elastic backbone. The specific case of a two-arm sheath is considered in detail and its relationship to a concentric tube balanced pair is described. Simulation and experiment are used to investigate the concept, map its workspace and to evaluate the kinematic model.
RESUMEN
OBJECTIVE: We sought to develop an instrument that would enable the delivery of artificial chordae tendineae (ACT) using optical visualization of the leaflet inside the beating heart. METHODS: A delivery instrument was developed together with an ACT anchor system. The instrument incorporates an optically clear silicone grasping surface in which are embedded a camera and LED for direct leaflet visualization during localization, grasping, and chordal delivery. ACTs, comprised of T-shaped anchors and an expanded polytetrafluoroethylene chordae, were fabricated to enable testing in a porcine model. Ex vivo experiments were used to measure the anchor tear-out force from the mitral leaflets. In vivo experiments were performed in which the mitral leaflets were accessed transapically using only optical guidance and ACTs were deployed in the posterior and anterior leaflets (P2 and A2 segments). RESULTS: In 5 porcine ex vivo experiments, the mean force required to tear the anchors from the leaflets was 3.8 ± 1.2 N. In 5 porcine in vivo nonsurvival procedures, 14 ACTs were successfully placed in the leaflets (9 in P2 and 5 in A2). ACT implantation took an average of 3.22 ± 0.83 minutes from entry to exit through the apex. CONCLUSIONS: Optical visualization of the mitral leaflet during chordal placement is feasible and provides direct feedback to the operator throughout the deployment sequence. This enables visual confirmation of the targeted leaflet location, distance from the free edge, and successful deployment of the chordal anchor. Further studies are needed to refine and assess the device for clinical use.
Asunto(s)
Cuerdas Tendinosas/cirugía , Implantación de Prótesis de Válvulas Cardíacas/instrumentación , Prótesis Valvulares Cardíacas/normas , Imagen Óptica/métodos , Animales , Diseño de Equipo , Implantación de Prótesis de Válvulas Cardíacas/métodos , Ensayo de Materiales/métodos , Válvula Mitral/cirugía , Prolapso de la Válvula Mitral/cirugía , Modelos Anatómicos , Cirugía Asistida por Computador/instrumentación , Cirugía Asistida por Computador/métodos , PorcinosRESUMEN
The shape of a concentric tube robot depends not only on the relative rotations and translations of its constituent tubes, but also on the history of relative tube displacements. Existing mechanics-based models neglect all history-dependent phenomena with the result that when calibrated on experimental data collected over a robot's workspace, the maximum tip position error can exceed 8 mm for a 200-mm-long robot. In this paper, we develop a model that computes the bounding kinematic solutions in which Coulomb friction is acting either to maximize or minimize the relative twisting between each pair of contacting tubes. The path histories associated with these limiting cases correspond to first performing all tube translations and then performing relative tube rotations of sufficient angle so that the maximum Coulomb friction force is obtained along the interface of each contacting tube pair. The robot tip configurations produced by these path histories are shown experimentally to bound position error with respect to the estimated frictionless model compared to path histories comprised of translation or mixed translation and rotation. Intertube friction forces and torques are computed as proportional to the intertube contact forces. To compute these contact forces, the standard zero-clearance assumption that constrains the concentrically combined tubes to possess the same centerline is relaxed. The effects of clearance and friction are explored through numerical and physical experiments and it is shown that friction can explain much of the prediction error observed in existing models. This model is not intended for real-time control, but rather for path planning-to provide error bounds and to inform how the ordering of tube rotations and translations can be used to reduce the effect of friction.
RESUMEN
BACKGROUND: Bilateral anterior cingulotomy has been used to treat chronic pain, obsessive compulsive disorder, and addictions. Lesioning of the target area is typically performed using bilateral stereotactic electrode placement and target ablation, which involves transparenchymal access through both hemispheres. OBJECTIVE: To evaluate an endoscopic direct-vision lesioning using a unilateral parasagittal minicraniotomy for minimally invasive bilateral anterior cingulotomy using a novel multiport endoscope through the anterior interhemispheric fissure. METHODS: A novel multiport magnetic resonance imaging (MRI)-compatible neuroendoscope prototype is used to demonstrate cadaveric cingulate lesioning through a lateral imaging port while simultaneously viewing the pericallosal arteries as landmarks through a tip imaging port. The lateral port enables extended lesioning of the gyrus while rotation of the endoscope about its axis provides access to homologous areas of both hemispheres. RESULTS: Cadaver testing confirmed the capability to navigate the multiport neuroendoscope between the hemispheres using concurrent imaging from the tip and lateral ports. The lateral port enabled exploration of the gyrus, visualization of lesioning, and subsequent inspection of lesions. Tip-port imaging provided navigational cues and allowed the operator to ensure that the endoscope tip did not contact tissue. The multiport design required instrument rotation in the coronal plane of only 20° to lesion both gyri, while a standard endoscope necessitated a rotation of 54°. CONCLUSION: Multiport MRI-compatible endoscopy can be effectively used in cisternal endoscopy, whereby a unilateral parasagittal minicraniotomy can be used for endoscopic interhemispheric bilateral anterior cingulotomy.