Toward Ideal Low-Frequency Noise in Monolayer CVD MoS2 FETs: Influence of van der Waals Junctions and Sulfur Vacancy Management.

The pursuit of sub-1-nm field-effect transistor (FET) channels within 3D semiconducting crystals faces challenges due to diminished gate electrostatics and increased charge carrier scattering. 2D semiconductors, exemplified by transition metal dichalcogenides, provide a promising alternative. However, the non-idealities, such as excess low-frequency noise (LFN) in 2D FETs, present substantial hurdles to their realization and commercialization. In this study, ideal LFN characteristics in monolayer MoS2 FETs are attained by engineering the metal-2D semiconductor contact and the subgap density of states (DOS). By probing non-ideal contact resistance effects using CuS and Au electrodes, it is uncovered that excess contact noise in the high drain current (ID) region can be substantially reduced by forming a van der Waals junction with CuS electrodes. Furthermore, thermal annealing effectively mitigates sulfur vacancy-induced subgap density of states (DOS), diminishing excess noise in the low ID region. Through meticulous optimization of metal-2D semiconductor contacts and subgap DOS, alignment of 1/f noise with the pure carrier number fluctuation model is achieved, ultimately achieving the sought-after ideal LFN behavior in monolayer MoS2 FETs. This study underscores the necessity of refining excess noise, heralding improved performance and reliability of 2D electronic devices.

Proposition of Adaptive Read Bias: A Solution to Overcome Power and Scaling Limitations in Ferroelectric-Based Neuromorphic System.

Hardware neuromorphic systems are crucial for the energy-efficient processing of massive amounts of data. Among various candidates, hafnium oxide ferroelectric tunnel junctions (FTJs) are highly promising for artificial synaptic devices. However, FTJs exhibit non-ideal characteristics that introduce variations in synaptic weights, presenting a considerable challenge in achieving high-performance neuromorphic systems. The primary objective of this study is to analyze the origin and impact of these variations in neuromorphic systems. The analysis reveals that the major bottleneck in achieving a high-performance neuromorphic system is the dynamic variation, primarily caused by the intrinsic 1/f noise of the device. As the device area is reduced and the read bias (VRead ) is lowered, the intrinsic noise of the FTJs increases, presenting an inherent limitation for implementing area- and power-efficient neuromorphic systems. To overcome this limitation, an adaptive read-biasing (ARB) scheme is proposed that applies a different VRead to each layer of the neuromorphic system. By exploiting the different noise sensitivities of each layer, the ARB method demonstrates significant power savings of 61.3% and a scaling effect of 91.9% compared with conventional biasing methods. These findings contribute significantly to the development of more accurate, efficient, and scalable neuromorphic systems.

Self-Curable Synaptic Ferroelectric FET Arrays for Neuromorphic Convolutional Neural Network.

With the recently increasing prevalence of deep learning, both academia and industry exhibit substantial interest in neuromorphic computing, which mimics the functional and structural features of the human brain. To realize neuromorphic computing, an energy-efficient and reliable artificial synapse must be developed. In this study, the synaptic ferroelectric field-effect-transistor (FeFET) array is fabricated as a component of a neuromorphic convolutional neural network. Beyond the single transistor level, the long-term potentiation and depression of synaptic weights are achieved at the array level, and a successful program-inhibiting operation is demonstrated in the synaptic array, achieving a learning accuracy of 79.84% on the Canadian Institute for Advanced Research (CIFAR)-10 dataset. Furthermore, an efficient self-curing method is proposed to improve the endurance of the FeFET array by tenfold, utilizing the punch-through current inherent to the device. Low-frequency noise spectroscopy is employed to quantitatively evaluate the curing efficiency of the proposed self-curing method. The results of this study provide a method to fabricate and operate reliable synaptic FeFET arrays, thereby paving the way for further development of ferroelectric-based neuromorphic computing.

Recovery of off-state stress-induced damage in FET-type gas sensor using self-curing method.

The need for high-performance gas sensors is driven by concerns over indoor and outdoor air quality, and industrial gas leaks. Due to their structural diversity, vast surface area, and geometric tunability, metal oxides show significant potential for the development of gas sensing systems. Despite the fact that several previous reports have successfully acquired a suitable response to various types of target gases, it remains difficult to maintain the reliability of metal oxide-based gas sensors. In particular, the degradation of the sensor platform under repetitive operation, such as off-state stress (OSS) causes significant reliability issues. We investigate the impact of OSS on the gas sensing performances, including response, low-frequency noise, and signal-to-noise ratio of horizontal floating-gate field-effect-transistor (FET)-type gas sensors. The 1/f noise is increased after the OSS is applied to the sensor because the gate oxide is damaged by hot holes. Therefore, the SNR of the sensor is degraded by the OSS. We applied a self-curing method based on a PN-junction forward current at the body-drain junction to repair the damaged gate oxide and improve the reliability of the sensor. It has been demonstrated that the SNR degradation caused by the OSS can be successfully recovered by the self-curing method.

In-Memory-Computed Low-Frequency Noise Spectroscopy for Selective Gas Detection Using a Reducible Metal Oxide.

Concerns about indoor and outdoor air quality, industrial gas leaks, and medical diagnostics are driving the demand for high-performance gas sensors. Owing to their structural variety and large surface area, reducible metal oxides hold great promise for constructing a gas-sensing system. While many earlier reports have successfully obtained a sufficient response to various types of target gases, the selective detection of target gases remains challenging. In this work, a novel method, low-frequency noise (LFN) spectroscopy is presented, to achieve selective detection using a single FET-type gas sensor. The LFN of the sensor is accurately modeled by considering the charge fluctuation in both the sensing material and the FET channel. Exposure to different target gases produces distinct corner frequencies of the power spectral density that can be used to achieve selective detection. In addition, a 3D vertical-NAND flash array is used with the fast Fourier transform method via in-memory-computing, significantly improving the area and power efficiency rate. The proposed system provides a novel and efficient method capable of selectively detecting a target gas using in-memory-computed LFN spectroscopy and thus paving the way for the further development in gas sensing systems.

Synergistic improvement of sensing performance in ferroelectric transistor gas sensors using remnant polarization.

Gaseous pollutants, including nitrogen oxides, pose a severe threat to ecosystems and human health; therefore, developing reliable gas-sensing systems to detect them is becoming increasingly important. Among the various options, metal-oxide-based gas sensors have attracted attention due to their capability for real-time monitoring and large response. In particular, in the field of materials science, there has been extensive research into controlling the morphological properties of metal oxides. However, these approaches have limitations in terms of controlling the response, sensitivity, and selectivity after the sensing material is deposited. In this study, we propose a novel method to improve the gas-sensing performance by utilizing the remnant polarization of ferroelectric thin-film transistor (FeTFT) gas sensors. The proposed FeTFT gas sensor has IGZO and HZO as the conducting channel and ferroelectric layer, respectively. It is demonstrated that the response and sensitivity of FeTFT gas sensors can be modulated by engineering the polarization of the ferroelectric layer. The amount of reaction sites in IGZO, including electrons and oxygen vacancy-induced negatively charged oxygen, is changed depending on upward and downward polarization. The results of this study provide an essential foundation for further development of gas sensors with tunable sensing properties.