ABSTRACT
Since blood viscosity is a basic parameter for understanding hemodynamics in human physiology, great amount of research has been done in order to accurately predict this highly non-Newtonian flow property. However, previous works lacked in consideration of hemodynamic changes induced by heterogeneous vessel networks. In this paper, the effect of bifurcation on hemodynamics in a microvasculature is quantitatively predicted. The flow resistance in a single bifurcation microvessel was calculated by combining a new simple mathematical model with 3-dimensional flow simulation for varying bifurcation angles under physiological flow conditions. Interestingly, the results indicate that flow resistance induced by vessel bifurcation holds a constant value of approximately 0.44 over the whole single bifurcation model below diameter of 60µm regardless of geometric parameters including bifurcation angle. Flow solutions computed from this new model showed substantial decrement in flow velocity relative to other mathematical models, which do not include vessel bifurcation effects, while pressure remained the same. Furthermore, when applying the bifurcation angle effect to the entire microvascular network, the simulation results gave better agreements with recent in vivo experimental measurements. This finding suggests a new paradigm in microvascular blood flow properties, that vessel bifurcation itself, regardless of its angle, holds considerable influence on blood viscosity, and this phenomenon will help to develop new predictive tools in microvascular research.
Subject(s)
Hemodynamics , Microcirculation , Microvessels/physiology , Models, Cardiovascular , Animals , Blood Flow Velocity , Blood Viscosity , Computer Simulation , Humans , Mice , Microvessels/anatomy & histology , Models, Anatomic , Regional Blood Flow , Vascular ResistanceABSTRACT
In this study, we explored magnetic nanoparticles translocating through a nanopore in the presence of an inhomogeneous magnetic field. By detecting the ionic current blockade signals with a silicon nitride nanopore, we found that the translocation velocity that is driven by magnetic and hydrodynamic forces on a single magnetic nanoparticle can be accurately determined and is linearly proportional to the magnetization of the magnetic nanoparticle. Thus, we obtained the magneto-susceptibility of an individual nanoparticle and the average susceptibility over one hundred particles within a few minutes.
Subject(s)
Electrochemical Techniques , Magnetite Nanoparticles/analysis , Nanopores , Electrodes , Light , Magnetic Fields , Scattering, Radiation , Silicon Compounds/chemistryABSTRACT
In this paper, we propose a method for simulating nanopore structure by using conventional 3-D simulation tool to mimic the I-V behavior of the nanopore structure. In the simulation, we use lightly doped silicon for ionic solution where some parameters like electron affinity and dielectric constant are fitted to consider the ionic solution. By using this method, we can simulate the I-V behavior of nanopore structure depending on the location and the size of the sphere shaped silicon oxide which is considered to be an indicator of a DNA base. In addition, we simulate an Ionic Field Effect Transistor (IFET) which has basically the nanopore structure, and show that the simulated curves follow sufficiently the I-V behavior of the measurement data. Therefore, we think it is reasonable to apply parameter modeling mentioned above to simulate nanopore structure. The key idea is to modify electron affinity of silicon which is used to mimic the KCl solution to avoid band bending and depletion inside the nanopore. We could efficiently utilize conventional 3-D simulation tool to simulate the I-V behavior of nanopore structures.
Subject(s)
Computer-Aided Design , Conductometry/instrumentation , DNA/chemistry , DNA/genetics , Nanostructures/chemistry , Nanotechnology/instrumentation , Sequence Analysis, DNA/instrumentation , DNA/analysis , Equipment Design , Equipment Failure Analysis , Imaging, Three-Dimensional , Models, Chemical , Molecular Conformation , Nanostructures/ultrastructure , Transistors, ElectronicABSTRACT
The polymerase chain reaction (PCR) is widely used to amplify a small amount of DNA in samples for genetic analysis. Rapid and accurate amplification is prerequisite for broad applications including molecular diagnostics of diseases, food safety, and biological warfare tests. We have developed a rapid real-time micro-scale chip-based PCR system, which consists of six individual thermal cycling modules capable of independent control of PCR protocols. The PCR volume is 1 microl and it takes less than 20 min to complete 40 thermal cycles. To test utility of a chip-based PCR system as a molecular diagnostic device, we have conducted the first large-scale clinical evaluation study. Three independent clinical evaluation studies (n = 563) for screening the hepatitis B virus (HBV) infection, the most popular social epidemic disease in Asia, showed an excellent sensitivity, e.g. 94%, and specificity, e.g. 93%, demonstrating micro-scale chip-based PCR can be applied in molecular diagnostics.
Subject(s)
DNA, Viral/analysis , Hepatitis B virus/genetics , Hepatitis B/diagnosis , Oligonucleotide Array Sequence Analysis/instrumentation , Polymerase Chain Reaction/instrumentation , Silicon , Hepatitis B/virology , Humans , Reproducibility of Results , Sensitivity and SpecificityABSTRACT
We have characterized the immobilization of thiol-modified oligomers on Au surfaces and subsequent hybridization with a perfectly matched or single-base mismatched target using a quartz crystal microbalance (QCM) and fluorescence spectroscopy. The surface density of immobilized probe molecules and the hybridization efficiency depending on the type of buffer and salt concentration were investigated. We observed some ambiguities in surface coverage deduced from QCM measurement and adopted a complementary fluorescence displacement method. Direct comparison of surface coverage deduced from frequency change in QCM measurement and determined by the fluorescence exchange reaction revealed that QCM results are highly overestimated and the amount of overestimation strongly depends on the type of buffer and the structure of the film. Discrimination capability of the surface attached 15-mer probe was also examined using a single-base mismatched target at various hybridization temperatures. Hybridization efficiency depending on the type of single base mismatch was investigated using surface plasmon resonance (SPR).