A Cost-Effective and Chemical-Recycling Approach for Facile Preparation of Regenerated Cellulose Materials.

Cellulose is difficult to melt or dissolve. The dissolution and regeneration process paves the way to convert cellulose into diverse forms but still suffers from high costs and environmental pollution. Here, we developed a method that uses aqueous alkali to efficiently dissolve cellulose at a temperature above 0 °C in minutes for fabricating regenerated cellulose. Cellulose was modified with minimal carboxymethyl groups to weaken the intermolecular interaction and improve its dissolution. The modified cellulose can be commercially obtained from carboxymethyl cellulose manufacturing with low cost and high quality. The use of only aqueous alkali reduces pollution and facilitates chemical recycling, and the moderate dissolving temperature reduces energy consumption. The regenerated cellulose materials display excellent mechanical properties and can be recycled or biodegraded after use. The method allows the use of diverse raw materials and modifications to broaden its applicability. The study develops a low-cost and eco-friendly method to fabricate regenerated cellulose.

Digital Light 3D Printing of Double Thermoplastics with Customizable Mechanical Properties and Versatile Reprocessability.

Digital light processing (DLP) is a 3D printing technology offering high resolution and speed. Printable materials are commonly based on multifunctional monomers, resulting in the formation of thermosets that usually cannot be reprocessed or recycled. Some efforts are made in DLP 3D printing of thermoplastic materials. However, these materials exhibit limited and poor mechanical properties. Here, a new strategy is presented for DLP 3D printing of thermoplastics based on a sequential construction of two linear polymers with contrasting (stiff and flexible) mechanical properties. The inks consist of two vinyl monomers, which lead to the stiff linear polymer, and α-lipoic acid, which forms the flexible linear polymer via thermal ring-opening polymerization in a second step. By varying the ratio of stiff and flexible linear polymers, the mechanical properties can be tuned with Young's modulus ranging from 1.1 GPa to 0.7 MPa, while the strain at break increased from 4% to 574%. Furthermore, these printed thermoplastics allow for a variety of reprocessability pathways including self-healing, solvent casting, reprinting, and closed-loop recycling of the flexible polymer, contributing to the development of a sustainable materials economy. Last, the potential of the new material in applications ranging from soft robotics to electronics is demonstrated.

Recycling channel strategy in the presence of free-riding in the carbon neutrality era.

Recycling has become a critical response to the goals of reaching a carbon peak and achieving carbon neutrality. This study explores the effects of consumer free-riding behavior, the quality of recycling services, and the costs of channel transfers on the profitability of manufacturers and retailers in a dual-channel closed-loop supply chain (CLSC), focusing on the importance of recycling practices for carbon neutrality. Using consumer utility theory and a Stackelberg game model, we analyze the dynamics among these factors. Our results show that: (i) Consumer free-riding behavior slightly increases market demand and recycling volumes, enhancing profitability for both manufacturers and retailers in the dual-channel CLSC. (ii) The quality of recycling services and the transfer costs associated with retailer free-riding behavior jointly influence the profits of manufacturers and retailers. (iii) The effect of free-riding behavior on recycling services affects both forward sales and reverse recycling channels equally. This study provides valuable insights for decision-making in sustainable development practices in the recycling sector, significantly contributing to the goal of achieving carbon neutrality.

Waste management in the operating theatre.

INTRODUCTION: Poor clinical waste management and its effect on the environment is an increasingly recognised concern for global healthcare systems. Approximately two thirds of waste produced in healthcare is from the operating theatre. In the Republic of Ireland, an estimated 580,977 tonnes of hazardous waste was produced in 2019. The cost of incineration of this hazardous waste is approximately €2,125 per tonne and €935 per tonne for sterilisation. Pollution from incineration is substantial and harmful. METHODS: A literature review was performed on the topic of hospital waste management, specifically looking at the Republic of Ireland. A comparison could then be drawn between Ireland, Europe and the United States of America. Observation of our current operating theatre environment and practices were carried out. DISCUSSION: An increased focus towards sustainability and reusable equipment means that there is potentially a decreased amount of waste for disposal, but an increase in the process of sterilisation. Approximately 66% of healthcare related waste is inappropriately contaminated, meaning that significant savings are possible if correct segregation and recycling were to occur. An increase in the amount of bins, identification labels above bins and education of staff results in an increased likelihood of successful segregation of waste. Clear and concise hospital guidelines of what is considered hazardous versus non-hazardous waste will decrease the amount of inappropriately disposed items.

Safety assessment of the process Fucine Film, based on the Reifenhäuser technology, used to recycle post-consumer PET into food contact materials.

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Fucine Film (EU register number RECYC322), which uses the Reifenhäuser technology. The input material consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, including no more than 5% PET from non-food consumer applications. The flakes are extruded under vacuum into sheets. The recycled sheets are intended to be used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, excluded drinking water and beverages, for long-term storage at room temperature, with or without hotfill. Based on the limited data available, the Panel concluded that the information submitted to EFSA was inadequate to demonstrate that the recycling process Fucine Film is able to reduce potential unknown contamination of the input PET flakes to a concentration that does not pose a risk to human health.

Materials Challenges in the Electric Vehicle Transition.

The ongoing transition toward electric vehicles (EVs) is changing materials used for vehicle production, of which the consequences for the environmental performance of EVs are not well understood and managed. We demonstrate that electrification coupled with lightweighting of automobiles will lead to significant changes in the industry's demand not only for battery materials but also for other materials used throughout the entire vehicle. Given the automotive industry's substantial consumption of raw materials, changes in its material demands are expected to trigger volatilities in material prices, consequently impacting the material composition and attractiveness of EVs. In addition, the materials recovered during end-of-life recycling of EVs as the vehicle fleet turns over will impact recycled material supplies both positively and negatively, impacting material availabilities and the economic incentive to engage in recycling. These supply chain impacts will influence material usage and the associated environmental performance of not only the automotive sector but also other metal-heavy industries such as construction. In light of these challenges, we propose the need for new research to understand the dynamic materials impacts of the EV transition that encompasses its implications on EV adoption and fleet life cycle environmental performance. Effectively coordinating the coevolution of material supply chains is crucial for making the sustainable transition to EVs a reality.

New powder reuse schema in laser-based powder bed fusion of polymers.

The laser-based powder bed fusion of polymers (PBF-LB/P) process often utilizes a blend of powders with varying degrees of degradation. Specifically, for polyamide 12, the traditional reuse schema involves mixing post-processed powder with virgin powder at a predetermined ratio before reintroducing it to the process. Given that only about 15% of the powder is utilized in part production, and powders are refreshed in equal proportions, there arises a challenge with the incremental accumulation of material across build cycles. To mitigate the consumption of fresh powder relative to the actual material usage, this study introduces the incorporation of recycled material into the PBF-LB/P process. This new powder reuse schema is presented for the first time, focusing on the laser sintering process. The characteristics of the recycled powder were evaluated through scanning electron microscopy, differential scanning calorimetry, X-ray diffraction, particle size distribution, and dynamic powder flowability assessments. The findings reveal that waste powders can be effectively reused in PBF-LB/P to produce components with satisfactory mechanical properties, porosity levels, dimensional accuracy, and surface quality.

Stepwise extraction of lithium and potassium and recovery of fluoride from aluminum electrolyte wastes through calcification roasting-two-stage leaching.

Aluminum electrolyte is a necessity for aluminum reduction cells; however, its stock is rising every year due to several factors, resulting in the accumulation of solid waste. Currently, it has become a favorable material for the resources of lithium, potassium, and fluoride. In this study, the calcification roasting-two-stage leaching process was introduced to extract lithium and potassium separately from aluminum electrolyte wastes, and the fluoride in the form of CaF2 was recycled. The separation behaviors of lithium and potassium under different conditions were investigated systematically. XRD and SEM-EDS were used to elucidate the phase evolution of the whole process. During calcification roasting-water leaching, the extraction efficiency of potassium was 98.7% under the most suitable roasting parameters, at which the lithium extraction efficiency was 6.6%. The mechanism analysis indicates that CaO combines with fluoride to form CaF2, while Li-containing and K-containing fluorides were transformed into water-insoluble LiAlO2 phase and water-soluble KAlO2 phase, respectively, thereby achieving the separation of two elements by water leaching. In the second acid-leaching stage, the extraction efficiency of lithium was 98.8% from water-leached residue under the most suitable leaching conditions, and CaF2 was obtained with a purity of 98.1%. The present process can provide an environmentally friendly and promising method to recycle aluminum electrolyte wastes and achieve resource utilization.

Sustainable methanol production from carbon dioxide: advances, challenges, and future prospects.

The urgent need to address global carbon emissions and promote sustainable energy solutions has led to a growing interest in carbon dioxide (CO2) conversion technologies. Among these, the transformation of CO2 into methanol (MeOH) has gained prominence as an effective mitigation strategy. This review paper provides a comprehensive exploration of recent advances and applications in the direct utilization of CO2 for the synthesis of MeOH, encompassing various aspects from catalysts to market analysis, environmental impact, and future prospects. We begin by introducing the current state of CO2 mitigation strategies, highlighting the significance of carbon recycling through MeOH production. The paper delves into the chemistry and technology behind the conversion of CO2 into MeOH, encompassing key themes such as feedstock selection, material and energy supply, and the various conversion processes, including chemical, electrochemical, photochemical, and photoelectrochemical pathways. An in-depth analysis of heterogeneous and homogeneous catalysts for MeOH synthesis is provided, shedding light on the advantages and drawbacks of each. Furthermore, we explore diverse routes for CO2 hydrogenation into MeOH, emphasizing the technological advances and production processes associated with this sustainable transformation. As MeOH holds a pivotal role in a wide range of chemical applications and emerges as a promising transportation fuel, the paper explores its various chemical uses, transportation, storage, and distribution, as well as the evolving MeOH market. The environmental and energy implications of CO2 conversion to MeOH are discussed, including a thermodynamic analysis of the process and cost and energy evaluations for large-scale catalytic hydrogenation.

Assessment of direction changes in waste electrical and electronic equipment management in Poland.

A growing amount of waste electrical and electronic equipment (WEEE) indicates the need to verify the effectiveness of its management both nationally and globally. An analysis of the WEEE economy in Poland conducted over 5 years confirmed a 16.64% increase in the mass of collected equipment. The maximum annual mass of electrical and electronic equipment introduced to the market during this period was 607,240 Mg, with the average value exceeding 500,000 Mg. The WEEE category with the largest collected mass was waste code 20 01 36, which exceeded 235,000 Mg, whilst the highest waste weight accumulation rate of 45.98 kg per capita was recorded in one of the smallest voivodeships in Poland. This result showed the diversity of WEEE accumulation on a national scale. Overall, a noticeable increase in the WEEE accumulation rate has occurred as Poland's gross domestic product has increased, despite a decreasing population. An analysis based on the waste accumulation indicators, including socioeconomic factors, confirmed the need to develop forms of WEEE recovery and recycling to transition to a circular economy and promote the synergy of activities amongst all players in WEEE management.

A review of plastic waste nanocomposites: assessment of features and applications.

Hundreds of millions of metric tons of plastic waste are generated globally every year. Processing waste into secondary raw material is preferred over energy production and landfilling. However, mechanical recycling generally deteriorates the properties of plastic waste limiting its range of potential applications. Nanocomposite fabrication is a solution to recycle plastic waste into value-added applications due to improved properties generated by nanomaterial reinforcement, however received little study. The aim of this review is to present the current status, identify research gaps and provide topics for further research of polymer nanocomposites prepared from plastic waste in respect to utilized materials, processing methods, enhanced properties, sustainability, economics, nanomaterial safety, and applications. It is found that morphological, mechanical, thermal, flame retardancy, physical, barrier, electrical and shielding properties of plastic waste can be enhanced with low loadings of different nanomaterials making them promising materials for various applications including electronic, shielding, thermal, packaging, filtration, and water treatment. Utilization of plastic waste instead of virgin polymers can be beneficial in respect to economics and sustainability, but the energy intensive and expensive production of the most nanomaterials, and the plastic waste pretreatment methods can negate these benefits. To enhance sustainability, further research should be conducted on utilization of energy friendly nanomaterials in plastic waste nanocomposites. Further research is needed also on polymer nanocomposite safety because of the unknow composition of the plastic waste and the potential for nanomaterial release during nanocomposite's life cycle. All in all, further research and national regulations and guidance are needed on virgin polymer and plastic waste nanocomposites.

Recycling and reuse of waste agricultural plastics with hydrothermal pretreatment and low-temperature pyrolysis method.

Recycling and reuse of agricultural plastics is an urgent worldwide issue. In this work, it is shown that low-density polyethylene (PE) typically used in mulch films can be converted into high-capacity P and N adsorbents through a two-step method that uses hydrothermal pretreatment (180 °C, 24 h) followed by pyrolysis at 500 °C with Ca(OH)2 additive. CaPE@HC500 materials prepared with the proposed two-step method were found to have high adsorption capacities for phosphate (263.6 mg/g) and nitrogen (200.7 mg/g) over wide ranges of pH (3-11). Dynamic adsorption of phosphate by CaPE@HC500 material in a packed-bed had a half-time breakthrough of 210 min indicating the feasibility of continuous systems. Material stability, cost, environmental-friendliness, and recyclability of the CaPE@HC500 material were determined to be superior to literature-proposed Ca-containing adsorbents. The two-step method for converting waste agricultural plastic mulch films into adsorbents is robust and highly-applicable to industrial settings.

Ultrasound-assisted efficient and convenient method of extracting valuable metals (Ni, Co, and Cd) from waste Ni-Cd batteries using DL-malic acid.

Recycling waste Ni-Cd batteries has received much attention recently because of the serious environmental pollution they cause and to avoid the dissipation of valuable metals. Despite significant research, it is still difficult to efficiently recycle valuable and hazardous metals from waste Ni-Cd batteries in an economical and environmentally friendly manner. This study employed a novel process utilizing ultrasound-assisted leaching to recover Ni, Cd, and Co from waste nickel-cadmium (Ni-Cd) batteries. Organic DL-malic acid served as the leaching agent and H2O2 was employed as an oxidizing agent. The effects of various factors on the recovery efficiency of Ni, Cd, and Co, such as leaching temperature, time, DL-malic acid concentration, pulp density, H2O2 concentration, and ultrasound frequency, were also examined. To predict the chemical compounds present before and after the recycling experiments, the solid residues from the metal extraction were analyzed using XRD, XPS, FE-SEM, and EDS element mapping. Concurrently, ICP-OES was utilized to determine the metal content in the leachate. Under optimized conditions of 90 °C, 90 min, 2M DL-malic acid, 160 mL/g pulp density, and 20% ultrasound frequency, over 83% of Ni, 94% of Cd, and 98% of Co were effectively leached from the waste Ni-Cd battery powder. The leaching kinetics of Ni, Cd, and Co followed the surface chemical reaction control model. The activation energies (Ea) for Ni, Cd, and Co leaching were 21.34, 20.47, and 18.38 kJ/mol, respectively. The findings suggest that ultrasound-assisted leaching is an efficient, cost-effective, environmentally friendly, and sustainable alternative for extracting precious and hazardous metals from waste Ni-Cd batteries. Additionally, it reduces industrial chemical usage and enhances waste management sustainability.

Fully Recycled Polyolefin Elastomer-Based Vitrimers with Ultra-High, Universal, Stable, and Switchable Adhesion.

Achieving both robust adhesion to arbitrary surfaces and thermal-switchable/recyclable properties has proven challenging, particularly for commodity polyolefins. Herein, a simple and effective route is reported to transform polyolefins elastomer (POE) into a fully recycled epoxy-functionalized POE vitrimers (E-POE vit) with ultra-high, universal, stable, and switchable adhesion via facile free radical grafting and dynamic cross-linking. The resultant E-POE vit exhibits increase in adhesion strength on glass exceeding three to ten times compared to those commonly used polymers, due to the synergy of dense hydrogen (H)-bonds and strong interfacial affinity. In addition, E-POE vit also displays strong adhesion on diverse surfaces ranging from inorganic to organic while maintaining good stability in various harsh environments. More importantly, temperature-sensitive H-bonds allow E-POE vit to switch between attachment-detachment at alternating temperatures, resulting in reversible adhesion without adhesion loss, even after 10 cycles. Moreover, E-POE vit is able to be fully recycled and reused more than ten times via thermo-activated transesterification reactions with negligible change in structure and performance. This work may unlock strategies to fabricate high-performance commercial polymer-based adhesives with adhesion and recyclable features for intelligent and sustainable applications.

Hydrological dynamics in the China-Mongolia arid region: An integrated analysis of precipitation recycling and water vapor conversion.

This study examines the atmospheric water cycle dynamics in the China-Mongolia Arid Region (CMAR), a region significantly affected by aridity. By employing a combination of Empirical Orthogonal Function (EOF) analysis, ERA5 reanalysis data, and the Dynamic Recycling Model (DRM), we investigate the spatial and temporal variations in the Precipitation Recycling Ratio (PRR) and Precipitable Water Conversion Rate (PWCR) over a forty-year period (1979-2021). Our findings reveal that both PRR and PWCR are generally higher but decreasing in most subregions of CMAR, suggesting a notable contribution of local moisture to precipitation. We also identify an increasing trend in PRR across the northwestern subregions and a decreasing trend in other areas. Similarly, PWCR exhibits an increasing trend in the northwestern and southern subregions, while decreasing elsewhere, implying a decline in water vapor conversion and recycling efficiency. Furthermore, our EOF analysis uncovers distinct spatial patterns, with dominant modes accounting for significant variances in PRR and PWCR, correlating with local variations in atmospheric moisture and advective changes. These results underscore the complex interplay between regional topography, atmospheric dynamics, and the hydrological cycle in CMAR. The insights from this study are vital for formulating effective water management strategies and adapting to climate change impacts in arid regions, holding broad implications for environmental science, climate studies, and sustainable resource management. Our findings reveal distinct spatial patterns and contrasting trends in precipitation recycling and water vapor conversion across the subregions of CMAR. This heterogeneity underscores the importance of conducting analyses at finer spatial scales to avoid contradictory conclusions that can arise from topographic influences when treating CMAR as a single unit. Future studies should focus on smaller subregions to accurately capture the intricacies of the water cycle in this topographically complex arid region.

Physical, mechanical, and durability properties of concrete containing different waste synthetic fibers for green environment - A critical review.

The world is facing a major challenge on ways to manage the waste synthetic materials that are potentially polluting the environment. So, by 2040 it is estimated from the total synthetic textile products that will be produced, the accumulated synthetic textile waste will be more than 73.77 %, if recycling of waste may not be managed by novel technology in different sectors. Hence, this is a great challenge coming to the world if it is not effectively recycled mainly to be used in the construction sector which covers a broad area. However, detailed critical review is needed to gather different authors result on waste synthetic fiber effectively utilized in construction materials like in a concrete. So, the present study reviewed, the effects of waste synthetic fibers specifically, which are covering many numbers of synthetic materials; polyester, nylon, and polyethylene replacement on the physical, mechanical, durability, and microstructural properties of concrete. As the review of most researchers indicates, reinforcing the waste synthetic fibers in the concrete by 0.1-1% to the weight of cement reduces workability, improves compressive, flexural, splitting tensile strength, and enhances durability. Specifically, adding around 0.5 % doses to the volume of the concrete makes good resistance to water absorption, chloride ion penetration, acidic attack, elevated temperature resistance below 600°C, and lessen concrete content hence, cost effective compared to the control concrete mixture. Besides these, the employment of waste synthetic fibers makes dense microstructure, consequently minimizes the crack occurrence and propagation.

Response surface methodology and machine learning optimisations comparisons of recycled AA6061-B4C-ZrO2 hybrid metal matrix composites via hot forging forming process.

The optimal conditions of applied factors to reuse Aluminium AA6061 scraps are (450, 500, and 550) °C preheating temperature, (1-15) % Boron Carbide (B4C), and Zirconium (ZrO2) hybrid reinforced particles at 120 min forging time via Hot Forging (HF) process. The response surface methodology (RSM) and machine learning (ML) were established for the optimisations and comparisons towards materials strength structure. The Ultimate Tensile Strength (UTS) strength and Microhardness (MH) were significantly increased by increasing the processed temperature and reinforced particles because of the material dispersion strengthening. The high melting point of particles caused impedance movements of aluminium ceramics dislocations which need higher plastic deformation force and hence increased the material's mechanical and physical properties. But, beyond Al/10 % B4C + 10 % ZrO2 the strength and hardness were decreased due to more particle agglomeration distribution. The optimisation tools of both RSM and ML show high agreement between the reported results of applied parameters towards the materials' strength characterisation. The microstructure analysis of Field Emission Scanning Electron Microscopy (FE-SEM) and Atomic Force Microscope (AFM) provides insights mapping behavioural characterisation supports related to strength and hardness properties. The distribution of different volumes of ceramic particle proportion was highlighted. The environmental impacts were also analysed by employing a life cycle assessment (LCA) to identify energy savings because of its fewer processing steps and produce excellent hybrid materials properties.

Materials recovery from NMC batteries with water as the sole solvent.

We report an environmentally benign recycling approach for large-capacity nickel manganese cobalt (NMC) batteries through the electrochemical concentration of lithium on the anode and subsequent recovery with only water. Cycling of the NMC pouch cells indicated the potential for maximum lithium recovery at a 5C charging rate. The anodes extracted from discharged and disassembled cells were submerged in deionized water, resulting in lithium dissolution and graphite recovery from the copper foils. A maximum of 13 mg of lithium salts per 100 mg of the anode, copper current collector, and separator was obtained from NMC pouch cell cycled at a 4C charging rate. The lithium salts extracted from batteries cycled at low C-rates were richer in lithium carbonate, while the salts from batteries cycled at high C-rates were richer in lithium oxides and peroxides, as determined by X-Ray photoelectron spectroscopy. The present method can be successfully used to recover all the pouch cell components: lithium, graphite, copper, and aluminum current collectors, separator, and the cathode active material.

Improved recycling of a gasification fly ash: An integrated waste management approach within the framework of a Circular Economy.

A Circular Waste Management alternative is considered in this paper in which a complete ash valorization process is proposed for an Integrated Gasification with Combined Cycle fly ash, trying to extract maximum value from this waste before it is discarded. In the paper, germanium, a scarce resource vital in our modern society, is first extracted from fly ash using water, with an extraction yield of 85%, and subsequently, the leached fly ash is used in the manufacture of fire-resistant boards containing 60% ash, thereby avoiding its disposal in a landfill. The potential environmental impact caused by the two stages of the process was analyzed, and the final effluent was considered to achieve a zero-discharge objective. This paper contributes to the development of a more sustainable management alternative for an industrial waste produced in increased amounts and provides the basis for a symbiotic coupling relationship among various industrial sectors.

Valorization of agro-forest wastes (oak acorns, vineyard pruning, and olive pruning) through the cultivation of shiitake (Lentinula edodes) mushrooms.

Experimental research has been focusing on developing new substrates for growing shiitake mushrooms as alternatives to the standard oak sawdust substrate. The selection of appropriate lignocellulosic materials is based on their availability in the production area and their compatibility with the requirements of the mushroom species being cultivated. In comparison to oak sawdust substrate (OS) as the control, this study evaluated the potential of oak acorns (OA), olive pruning (OLPR), and vineyard pruning (VIP), and various combinations: OA-OLPR:1-1, OA-VIP:1-1, OS-OLPR:1-1, and OS-VIP:1-1, prepared on a dry weight basis. In comparison to OS, complete mycelial development was hastened in OA, OA-VIP: 1-1, and OS-VIP:1-1 by 9.5, 7.9, and 4.2 days and delayed in OLPR and OS-OLPR:1-1 by 11.3 and 7.0 days, respectively. Also, harvest was earlier in OA, OA-VIP:1-1, and OS-VIP:1-1 by 9.3, 6.7, and 3.3 days, respectively, while it was significantly delayed in OLPR, VIP, and OS-OLPR:1-1 by 12.3, 3.7, and 8.0 days, respectively. While the total biological yield was significantly reduced in OLPR, OS-OLPR:1-1, VIP, and OS-VIP:1-1, it was comparable to OS in OA, OA-OLPR:1-1, and OA-VIP:1-1 (597.0, 552.0, 532.2, and 556.2 g/kg, respectively). Production was consistently high over two consecutive flushes in OS, OA, and OA-VIP: 1-1. Total biological yields were higher in OA-OLPR: 1-1 than OS-OLPR:1-1 and in OA-VIP:1-1 than OS-VIP:1-1. OA increased mushroom number and firmness, VIP and OLPR increased mushroom weight, and OA-VIP:1-1 increased pileus thickness. Mushrooms' protein and fiber contents were higher than OS in all substrates and the highest in OA-OLPR:1-1 (8.7 %) and OLPR (2.8 %), respectively. Conclusively, the substrates OA, OA-VIP: 1-1, and OA-OLPR:1-1 may alternate oak sawdust; however, the first two substrates have an advantage over the third due to earlier harvests. Also, it is more favorable to use VIP and OLPR in combination with OA than to use them alone.