[Inter-laboratory Study on the Modified Methods for Analyzing Bisphenol A Content for Migration Tests from Polycarbonate Food Apparatuses, Containers, and Packaging].

An inter-laboratory study involving 24 laboratories was conducted to validate the modified analytical method for the migration solution of heptane for the determination of bisphenol A migrating from polycarbonate food processing materials. In this study, two concentrations of samples were blindly coded. Each laboratory determined the analyte (bisphenol A, phenol and p-tert-butylphenol) concentration in each sample according to the established protocol. The obtained values were analyzed statistically using internationally accepted guidelines. Horwitz ratios were calculated based on the reproducibility relative standard deviation (RSDR), which was estimated from the inter-laboratory study, and predicted RSDR, which was calculated using the Horwitz/Thompson equation. Horwitz ratios of the two samples ranged from 0.15 to 0.37 for the three compounds, meeting the performance criteria of less than 2 set by the Codex Alimentarius for analytical method approval. These results showed that this modified analytical method shows good performance as an analytical method for the migration solution of heptane.

[Interlaboratory Study on Evaporation Residue Test for Food Contact Products (Report 1)].

An interlaboratory study was performed to evaluate the equivalence between an official method and a modified method of evaporation residue test using three food-simulating solvents (water, 4% acetic acid and 20% ethanol), based on the Japanese Food Sanitation Law for food contact products. Twenty-three laboratories participated, and tested the evaporation residues of nine test solutions as blind duplicates. For evaporation, a water bath was used in the official method, and a hot plate in the modified method. In most laboratories, the test solutions were heated until just prior to evaporation to dryness, and then allowed to dry under residual heat. Statistical analysis revealed that there was no significant difference between the two methods, regardless of the heating equipment used. Accordingly, the modified method provides performance equal to the official method, and is available as an alternative method.

[Interlaboratory Study on Evaporation Residue Test for Food Contact Products (Report 2)].

An interlaboratory study was performed to evaluate the equivalence between an official method and a modified method of evaporation residue test using heptane as a food-simulating solvent for oily or fatty foods, based on the Japanese Food Sanitation Law for food contact products. Twenty-three laboratories participated, and tested the evaporation residues of nine test solutions as blind duplicates. In the official method, heating for evaporation was done with a water bath. In the modified method, a hot plate was used for evaporation, and/or a vacuum concentration procedure was skipped. In most laboratories, the test solutions were heated until just prior to dryness, and then allowed to dry under residual heat. Statistical analysis revealed that there was no significant difference between the two methods. Accordingly, the modified method provides performance equal to the official method, and is available as an alternative method. Furthermore, an interlaboratory study was performed to evaluate and compare two leaching solutions (95% ethanol and isooctane) used as food-simulating solvents for oily or fatty foods in the EU. The results demonstrated that there was no significant difference between heptane and these two leaching solutions.

PCR-Based Method for the Detection of Toxic Mushrooms Causing Food-Poisoning Incidents.

In this study, species-specific identification of five toxic mushrooms, Chlorophyllum molybdites, Gymnopilus junonius, Hypholoma fasciculare, Pleurocybella porrigens, and Tricholoma ustale, which have been involved in food-poisoning incidents in Japan, was investigated. Specific primer pairs targeting internal transcribed spacer (ITS) regions were designed for PCR detection. The specific amplicons were obtained from fresh, cooked, and simulated gastric fluid (SGF)-treated samples. No amplicons were detected from other mushrooms with similar morphology. Our method using one-step extraction of mushrooms allows rapid detection within 2.5 hr. It could be utilized for rapid identification or screening of toxic mushrooms.

Detection of Histamine in Fish and Fishery Products in Osaka Prefecture (Fiscal 2015 Report).

Histamine food poisoning is caused by ingestion of spoiled fish containing high levels of histamine. This paper reports cases in which histamine was detected in Osaka prefecture in fiscal year 2015 in a survey of fish and fishery products on the market and the food poisoning. A suspected case of histamine food poisoning was also evaluated to investigate the cause and minimize further problems. Histamine in food was separated on SPE cartridge columns, and analyzed after derivatization with fluorescamine by means of HPLC-FL. Histamine was detected in some fishery products on the market and in food that had caused poisoning. The samples in which histamine was detected were semi-dried whole round herring (Urumeiwashi-maruboshi), mackerel (Saba) and sardine dumpling (Iwashi-tsumire). These foods were the main causes of histamine food poisoning according to the report of the Ministry of Health, Labour and Welfare, Government of Japan.

Interlaboratory Study on Caprolactam Test for Food-Contact Nylon Products.

The Japanese Food Sanitation Law sets a limit on the migration level of caprolactam for food-contacting nylon products. Here, we carried out an interlaboratory study in twenty laboratories to evaluate the performance of the official GC-FID test method and a GC-MS method as an alternative test method to the official method. Each laboratory quantified caprolactam in three test solutions in 20% ethanol as blind duplicates using GC-FID or GC-MS. The official method (GC-FID with absolute calibration) gave trueness, repeatability (RSDr) and reproducibility (RSDr) values of 96-97%, 3.3-5.4% and 4.0-6.7%, respectively. These values met the target criteria (trueness: 80-110%, RSDr: 10%, RSDr: 25%). The performance of the method was further improved by the introduction of heptalactam as an internal standard. As for GC-MS method, some values of the RSDr exceeded 10% when absolute calibration was used. However, when an internal standard was introduced, the trueness, RSDr and RSDr of GC-MS method were all acceptable at 94-96%, 2.0-4.4% and 7.0-9.4%, respectively. Therefore, GC-MS with an internal standard is available as an alternative test method to the official method.

Interlaboratory Study on Volatiles Test for Food-Contacting Polystyrene Products.

Using polystyrene, acrylonitrile-styrene resin and acrylonitrile-butadiene-styrene resin pellets as samples, an interlaboratory study was performed to evaluate the volatiles test method, based on the specifications described in the Japanese Food Sanitation Law for food-contacting polystyrene products. The study was conducted with the participation of twenty-one laboratories. Each laboratory quantified the contents of styrene, toluene, ethylbenzene, isopropylbenzene and propylbenzene in three test pellets using GC-FID, GC-MS or headspace-GC-FID. Statistical analysis revealed that the repeatability (RSDr) and reproducibility (RSDr) were 1.0-2.6 and 2.5-5.5% for the GC-FID method. The values of the performance parameters fulfilled the requirements (RSDr: 10%, RSDr: 25%), and the performance is sufficient for specifications testing. The RSDr and RSDr of results obtained using the GC-MS and HS-GC methods were 1.4-7.8 and 4.9-13%(GC-MS), and 2.0-2.6 and 3.3-6.9%(HS-GC-FID), respectively. The quantified levels were similar to those obtained with GC-FID. The study suggests that the GC-MS and HS-GC methods can be employed as alternative methods to the GC-FID method.

[Interlaboratory Study on Zinc Test for Food-Contact Rubber Products].

Using six kinds of zinc solution in water and 4% acetic acid as samples, an interlaboratory study was performed to evaluate a zinc (Zn) test method for food-contact rubber products, based on the Japanese Food Sanitation Law. Eighteen laboratories participated, and quantified Zn in six test solutions as blind duplicates using flame atomic absorption spectrometry, induced coupled plasma-optical emission spectrometry or induced coupled plasma-mass spectrometry. Statistical analysis revealed that the trueness, repeatability (RSDr) and reproducibility (RSDr) were 97-103%, 0.7-4.9% and 1.7-8.9% by all measuring methods. The values of the performance parameter fulfilled the target value (trueness: 80-110%, RSDr: 10%, RSDr: 25%). The performance of these methods is sufficient for testing the adherence of samples to the specifications.

[Interlaboratory study on migration test of antimony and germanium for food-contact polyethylene terephthalate].

An interlaboratory study was performed to evaluate a migration test method of antimony (Sb) and germanium (Ge), based on the Japanese Food Sanitation Law for food- contact polyethylene terephthalate. Eighteen laboratories participated, and quantified Sb and Ge in three test solutions as blind duplicates using graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma-optical emission spectrometry (ICP-OES) or induced coupled plasma-mass spectrometry (ICP-MS). Statistical analysis revealed that the trueness, repeatability and reproducibility were 98-107%, 1.7-7.5% and 2.0-18.8% by using GF-AAS and ICP-OES. The performance of these methods is sufficient for testing the specifications. The performance parameters of ICP-MS were 99-106%, 0.7-2.2% and 2.2-10.5%, respectively. ICP-MS is available as an alternative measuring method. However, in some laboratories, the quantitative values of Sb were higher than the addition levels. We found that Sb in working solutions is absorbed on glass vessels. Careful control of concentration in working solutions is required for Sb analysis.

[Interlaboratory study on migration test of cadmium and lead for food contact articles].

An interlaboratory study was performed to evaluate a migration test method of cadmium (Cd) and lead (Pb), based on the Japanese Food Sanitation Law for glassware, ceramicware, enamelware and metal cans. Seventeen laboratories participated, and quantified Cd and Pb in eight test solutions as blind duplicates using flame atomic absorption spectrometry (AAS), graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma-optical emission spectrometry (ICP-OES) or induced coupled plasma-mass spectrometry (ICP-MS). Statistical analysis revealed that the trueness, repeatability (RSDr) and reproducibility (RSDr) were 93-105%, 0.7-8.4% and 2.6-19.3% by using AAS, ICP-OES and ICP-MS (internal standard method). The performance of these methods is sufficient for testing specifications. However, some of the RSDr values exceeded 10% in GF-AAS, and careful control of accuracy is required.

[Performance comparison of material tests for cadmium and lead in food contact plastics].

Based on the Japanese Food Sanitation Law, the performances of official and alternative material test methods for cadmium (Cd) and lead (Pb) in food contact plastics were compared. Nineteen laboratories participated to an interlaboratory study, and quantified Cd and Pb in three PVC pellets. in the official method, a sample is digested with H2SO4, taken up in HCl, and evaporated to dryness on a water bath, then measured by atomic absorption spectrometry (AAS) or inductively coupled plasma-optical emission spectrometry (ICP-OES). Statistical treatment revealed that the trueness, repeatability (RSDr) and reproducibility (RSDr) were 86-95%, 3.1-9.4% and 8.6-22.1%, respectively. The values of the performance parameters fulfilled the requirements , and the performances met the test specifications. The combination of evaporation to dryness on a hot plate and measurement by AAS or ICP-OES is applicable as an alternative method. However, the trueness and RSDr were inferior to those of the official method. The performance parameters obtained by using the microwave digestion method (MW method) to prepare test solution were better than those of the official method. Thus, the MW method is available as an alternative method. Induced coupled plasma-mass spectrometry (ICP-MS) is also available as an alternative method. However, it is necessary to ensure complete digestion of the sample.

[Determination of histamine in fish and fish products by tandem solid-phase extraction].

A simple and practical method was developed for the determination of histamine in fish and fish products by solid-phase extraction and fluorescence derivatization. Histamine was extracted with trichloroacetic acid. The extract was neutralized and diluted with phosphate buffer (pH 6.8), and cleaned up with a tandem-connected octadecyl silica (ODS) and strong cation exchange silica (SCX) cartridge. After removal of the solvent, histamine was derivatized with fluorescamine and analyzed by ion-paired reversed-phase high-performance liquid chromatography with fluorescence detection. Recovery tests of histamine from six kinds of fish and fish products showed acceptable recovery (83-92%) with low relative standard deviation (less than 5%). This method could be useful for determination of histamine in fish.

[Rapid analysis of toxic heavy metals in foods for emergency response to health crisis].

A simple and rapid method for determination of intentional contamination with heavy metals in foods using inductively coupled plasma-atomic emission spectroscopy (ICP-AES) has been developed. The heavy metals were extracted with sulfuric acid in a disposable tube using a homogenizer. The extract was diluted with 1% HNO(3) solution and analyzed with ICP-AES. Recovery tests of 9 metals, As, Cd, Cr, Hg, Mn, Pb, Sb, Sn, and Tl, from 12 foods were performed, and gave acceptable recovery (71-107%) with low relative standard deviation (1-11%). The time required for conversion of 12 samples to test solutions was approximately 2 hr. This method could be useful for identification of heavy metals involved in food poisoning cases.

Determination of pyrethroid pesticides in cinnamomi cortex.

In Japan, maximum residue levels (MRL) have been set for eight pesticides (alpha-BHC, beta-BHC, gamma-BHC, delta-BHC (BHCs), p,p'-DDE, o,p'-DDT, p,p'-DDD, p,p'-DDT (DDTs)) in 14 crude drugs (below 0.2 ppm as total of BHCs, below 0.2 ppm as total of DDTs). There are fears that pesticides present in crude drugs for which MRL are set will be changed from BHCs and DDTs to other pesticides with MRL setting as the turning point. There are few surveys of pyrethroid pesticide in crude drugs distributed in Japan. The actual situation of pyrethroid pesticides in crude drugs distributed in Japan after setting MRL is not unclear and should be clarified. Although a method to analyze permethrin, cypermethrin and fenvalerate in 11 crude drugs was reported, it is not adequate because the recovery rates of permethrin, cypermethrin and fenvalerate from Cinnamomi cortex were very low and the method, including liquid-liquid partition is difficult. In this study, we developed a method using solid-phase extraction to analyze permethrin, cypermethrin and fenvalerate in Cinnamomi cortex with acceptable recovery rates. The sample solution was determined by gas chromatography/mass spectrometry with negative chemical ionization. The recovery rates of permethrin, cypermethrin and fenvalerate from Cinnamomi cortex were between 87.9 and 90.7%. Five samples of Cinnamomi cortex were analyzed according to the proposed method. No samples contained permethrin, cypermethrin and fenvalerate over detection limits. The proposed method could analyze permethrin, cypermethrin and fenvalerate in all crude drugs for which MRL are set.

[Determination of polysorbates in foods by solid-phase extraction and high-performance liquid chromatography].

A simple and rapid method using refractive index high-performance liquid chromatography (RI-HPLC) was developed for the determination of polysorbates (PS) in processed foods. PS were extracted with ethyl acetate containing 5% methanol. The extract was cleaned up on a multimode cartridge (300 mg) and an Alumina-N cartridge (500 mg) to remove fats and food color. HPLC separation was performed on a C18 column (4.6 i.d. x 150 mm) with methanol as the mobile phase. The recoveries of PS80 from nine kinds of foods fortified at the levels 1-5 g/kg were 80-99%. The limit of quantitation for PS80 in foods was 0.10 g/kg. The proposed method was applied to Worcestershire sauce that was PS-positive by TLC, and PS was confirmed to be present as PS80 at the concentration of 0.13 g/kg.

Profiling analysis of oligosaccharides in antibody pharmaceuticals by capillary electrophoresis.

Carbohydrate chains in glycoprotein pharmaceuticals have important roles for the expression of their biological activities. Therefore, development of an assessment method for the carbohydrate chains is an important parameter for quality control of glycoprotein pharmaceuticals such as newly developed therapeutic antibodies. In this report, we applied capillary electrophoresis with laser-induced fluorescence detection to the analysis of carbohydrate chains after releasing with glycoamidase followed by derivatization with 3-aminobenzoic acid. We found that four major oligosaccharides present in antibody pharmaceuticals were successfully separated with good resolution. The present method showed good precision in both migration times and relative peak areas, and gave comparable accuracy with that using a derivatization method with 8-aminopyrene-1,3,6-trisulfonate.