RESUMO
Liquid crystal elastomers (LCEs), consisting of polymer networks and liquid crystal mesogens, show a reversible phase change under thermal stimuli. However, the kinetic performance is limited by the inherently low thermal conductivity of the polymers. Transforming amorphous bulk into a fiber enhances thermal conductivity through the alignment of polymer chains. Challenges are present due to their rigid networks, while cross-links are crucial for deformation. Here, we employ hydrodynamic alignment to orient the LCE domains assisted by controlled in situ cross-linking and to remarkably reduce the diameter to submicrons. We report that the intrinsic thermal conductivity of LCE fibers at room temperature reaches 1.44 ± 0.32 W/m-K with the sub-100 nm diameter close to the upper limit determined in the quasi-1D regime. Combining the outstanding thermal conductivity and thin diameters, we anticipate these fibers to exhibit a rapid response and high force output in thermomechanical systems. The fabrication method is expected to apply to other cross-linked polymers.
RESUMO
Surface phonon polaritons (SPhPs) originate from the coupling of mid-IR photons and optical phonons, generating evanescent waves along the polar dielectric surface. The emergence of SPhPs gives rise to a phase of quantum matter that facilitates long-range energy transfer (100s µm-scale). Albeit of the recent experimental progress to observe the enhanced thermal conductivity of polar dielectric nanostructures mediated by SPhPs, the potential mechanism to present the high thermal conductivity beyond the Landauer limit has not been addressed. Here, we revisit the comprehensive theoretical framework to unify the distinct pictures of two heat transfer mechanisms by conduction and radiation. We first designed our experimental platform to distinguish contributions of two distinct fundamental modes of SPhPs, resulting in far-field radiation and long propagating conduction, respectively, by tuning the configuration of a nanostructured heat channel integrated into the thermometer. We could effectively control the transmission of long-propagating SPhPs to influence the apparent thermal conductivity of the nanostructure. This study reveals the high thermal conductance of 1.63 nW/K by a fast SPhP mode comparable to that by classical phonons, with measurements showing apparent conductivity values of up to 2 W/m·K at 515 K. The origin of the enhanced thermal conductivity was exploited by observing the interference of dispersive evanescent waves by double heat channels. Furthermore, our experimental observations of length-dependent thermal conductance by SPhPs are in good agreement with the revisited Landauer formula to illustrate a polaritonic mode of heat conduction, considering the dispersive nature of radiation not limited to the physical boundaries of a solid object yet directionally guided along the surface.
RESUMO
A laser power bed fusion (L-PBF) manufacturing process was optimized by analyzing the surface morphology and track width w of single scan tracks (SSTs) on Fe-3.4wt.%Si. An SST was evaluated under process conditions of laser power P, scan speed V, and energy density E = P/V. The SST surface shape was mainly affected by E; desirable thin and regular tracks were obtained at E = 0.3 and 0.4 J/mm. An L-PBF process window was proposed considering the optimal w of SST, and the appropriate range of E for the alloy was identified to be 0.24 J/mm to 0.49 J/mm. w showed a strong relationship with E and V, and an analytic model was suggested. To verify the process window derived from the appropriate w of SST, cubic samples were manufactured with the estimated optimal process conditions. Most samples produced had a high density with a porosity of <1%, and the process window derived from SST w data had high reliability. This study presents a comprehensive approach to enhancing additive manufacturing for Fe-3.4Si alloy, offering valuable insights for achieving high-quality samples without the need for time-intensive procedures.
RESUMO
Despite its important role in understanding ultrafast spin dynamics and revealing novel spin/orbit effects, the mechanism of the terahertz (THz) emission from a single ferromagnetic nanofilm upon a femtosecond laser pump still remains elusive. Recent experiments have shown exotic symmetry, which is not expected from the routinely adopted mechanism of ultrafast demagnetization. Here, by developing a bidirectional pump-THz emission spectroscopy and associated symmetry analysis method, we set a benchmark for the experimental distinction of the THz emission induced by various mechanisms. Our results unambiguously unveil a new mechanismâanomalous Nernst effect (ANE) induced THz emission due to the ultrafast temperature gradient created by a femtosecond laser. Quantitative analysis shows that the THz emission exhibits interesting thickness dependence where different mechanisms dominate at different thickness ranges. Our work not only clarifies the origin of the ferromagnetic-based THz emission but also offers a fertile platform for investigating the ultrafast optomagnetism and THz spintronics.
RESUMO
A classical thermal source, such as an incandescent filament, radiates according to Planck's law. The feasibility of super-Planckian radiation has been investigated with sub-wavelength-sized sources in the last decade. In such sources, a crystal-dependent coupling of photons and optical phonons is possible at thermal energies corresponding to that at room temperature. This interaction can be used to tailor the far-field thermal emission in a coherent manner; however, understanding heat transfer during this process is still nascent. Here, we used a novel measurement platform to quantify thermal signals in a Ge2Sb2Te5/SiO2 nanoribbon structure. We were able to separate and quantify the radiated and conducted heat transfer mechanisms. The thermal emission from the Ge2Sb2Te5/SiO2 nanoribbons was enhanced by 3.5× compared to that of a bare SiO2 nanoribbon. Our model revealed that this enhancement was directly due to polaritonic heat transfer, which was possible due to the large and lossless dielectric permittivity of Ge2Sb2Te5 at mid-IR frequencies. This study directly probes the far-field emission with a thermal gradient stimulated by Joule heating in temperature ranges from 100 to 400 K, which bridges the gap between mid-IR optics and thermal engineering.
RESUMO
Acoustic deformation potential (ADP) plays a significant role in quantifying carrier-acoustic phonon interactions in semiconductors. In this work, we report a novel ultrafast spectroscopy method to extract the ADP coupling constant of a semiconductor by jointly analyzing the coherent acoustic phonon signals with and without a metal transducer. By applying this method to GaAs, the ADP coupling constant corresponding to the band gap was extracted using a pump photon energy near the band gap, which agrees well with literature values. With a larger pump photon energy, the ADP coupling constant deviates from the one for the band gap, which is attributed to contributions from the carrier dynamics in multiple energy and wavevector states.
RESUMO
The evolution of the bacterial phosphotransferase system (PTS) linked to glycolysis is dependent on the availability of naturally occurring sugars. Although bacteria exhibit sugar specificities based on carbon catabolite repression, the acquisition and evolvability of the cellular sugar preference under conditions that are suboptimal for growth (e.g., environments rich in a rare sugar) are poorly understood. Here, we generated Escherichia coli mutants via a retro-aldol reaction to obtain progeny that can utilize the rare sugar d-tagatose. We detected a minimal set of adaptive mutations in the d-fructose-specific PTS to render E. coli capable of d-tagatose utilization. These E. coli mutant strains lost the tight regulation of both the d-fructose and N-acetyl-galactosamine PTS following deletions in the binding site of the catabolite repressor/activator protein (Cra) upstream from the fruBKA operon and in the agaR gene, encoding the N-acetylgalactosamine (GalNAc) repressor, respectively. Acquired d-tagatose catabolic pathways then underwent fine-tuned adaptation via an additional mutation in 1-phosphofructose kinase to adjust metabolic fluxes. We determined the evolutionary trajectory at the molecular level, providing insights into the mechanism by which enteric bacteria evolved a substrate preference for the rare sugar d-tagatose. Furthermore, the engineered E. coli mutant strain could serve as an in vivo high-throughput screening platform for engineering non-phosphosugar isomerases to produce rare sugars. IMPORTANCE Microorganisms generate energy through glycolysis, which might have preceded a rapid burst of evolution, including the evolution of cellular respiration in the primordial biosphere. However, little is known about the evolvability of cellular sugar preferences. Here, we generated Escherichia coli mutants via a retro-aldol reaction to obtain progeny that can utilize the rare sugar d-tagatose. Consequently, we identified mutational hot spots and determined the evolutionary trajectory at the molecular level. This provided insights into the mechanism by which enteric bacteria evolved substrate preferences for various sugars, accounting for the widespread occurrence of these taxa. Furthermore, the adaptive laboratory evolution-induced cellular chassis could serve as an in vivo high-throughput screening platform for engineering tailor-made non-phosphorylated sugar isomerases to produce low-calorigenic rare sugars showing antidiabetic, antihyperglycemic, and antitumor activities.
RESUMO
Synthetic tough hydrogels have received attention because they could mimic the mechanical properties of natural hydrogels, such as muscle, ligament, tendon, and cartilage. Many recent studies suggest various approaches to enhance the mechanical properties of tough hydrogels. However, directly comparing each hydrogel property in different reports is challenging because various testing specimen shapes/sizes were employed, affecting the experimental mechanical property values. This study demonstrates how the specimen geometry-the lengths and width of the reduced section-of a tough double-network hydrogel causes differences in experimental tensile mechanical values. In particular, the elastic modulus was systemically compared using eleven specimens of different shapes and sizes that were tensile tested, including a rectangle, ASTM D412-C and D412-D, JIS K6251-7, and seven customized dumbbell shapes with various lengths and widths of the reduced section. Unlike the rectangular specimen, which showed an inconsistent measurement of mechanical properties due to a local load concentration near the grip, dumbbell-shaped specimens exhibited a stable fracture at the reduced section. The dumbbell-shaped specimen with a shorter gauge length resulted in a smaller elastic modulus. Moreover, a relationship between the specimen dimension and measured elastic modulus value was derived, which allowed for the prediction of the experimental elastic modulus of dumbbell-shaped tough hydrogels with different dimensions. This study conveys a message that reminds the apparent experimental dependence of specimen geometry on the stress-strain measurement and the need to standardize the measurement of of numerous tough hydrogels for a fair comparison.
RESUMO
Kidney disability due to kidney failure could be considered to be the most severe of all the internal-organ disabilities. The purpose of this study was to identify the disease burden between the kidney and non-kidney disabled among the internal-organ disabled, based on the number of chronic diseases, annual out-of-pocket expenditure, and quality of life. From 2009 to 2013, 308 people (6.5%) with internal-organ disabilities were extracted out of 4732 people with disabilities in the Korea Health Panel. We compared the disease burden of 136 people with kidney disability (44.2%) and 172 people with non-kidney disability (55.8%), and confirmed the trend of disease burden over five years through panel analysis. The disease burden gap between kidney and non-kidney disabilities was, respectively, the number of chronic diseases (4.7 vs. 3.3, p < 0.0001), annual out-of-pocket expenditure ($1292 vs. $847, p < 0.004), and quality of life score out of 100 (49.2 vs. 60.2, p < 0.0001). In addition, when looking at the five-year trend of the three disease burden indexes, the kidney disabled were consistently worse than the non-kidney disabled (p < 0.01). In conclusion, health policy planners aiming for health equity need to seek practical strategies to reduce the gap in the disease burden among people with disabilities.
Assuntos
Pessoas com Deficiência , Qualidade de Vida , Efeitos Psicossociais da Doença , Humanos , Rim , República da Coreia/epidemiologiaRESUMO
This study investigated the mechanical properties of steel in flanges, with the goal of obtaining high strength and high toughness. Quenching was applied alone or in combination with tempering at one of nine combinations of three temperatures TTEM and durations tTEM. Cooling rates at various flange locations during quenching were first estimated using finite element method simulation, and the three locations were selected for mechanical testing in terms of cooling rate. Microstructures of specimens were observed at each condition. Tensile test and hardness test were performed at room temperature, and a Charpy impact test was performed at -46 °C. All specimens had a multiphase microstructure composed of matrix and secondary phases, which decomposed under the various tempering conditions. Decrease in cooling rate (CR) during quenching caused reduction in hardness and strength but did not affect low-temperature toughness significantly. After tempering, hardness and strength were reduced and low-temperature toughness was increased. Microstructures and mechanical properties under the various tempering conditions and CRs during quenching were discussed. This work was based on the properties directly obtained from flanges under industrial processes and is thus expected to be useful for practical applications.
RESUMO
Thermal rectification is an exotic thermal transport phenomenon which allows heat to transfer in one direction but block the other. We demonstrate an unusual dual-mode solid-state thermal rectification effect using a heterogeneous "irradiated-pristine" polyethylene nanofiber junction as a nanoscale thermal diode, in which heat flow can be rectified in both directions by changing the working temperature. For the nanofiber samples measured here, we observe a maximum thermal rectification factor as large as ~50%, which only requires a small temperature bias of <10 K. The tunable nanoscale thermal diodes with large rectification and narrow temperature bias open up new possibilities for developing advanced thermal management, energy conversion and, potentially thermophononic technologies.
RESUMO
In comparison with the advancement of switchable, nonlinear, and active components in electronics, solid-state thermal components for actively controlling heat flow have been extremely rare. We demonstrate a high-contrast and reversible polymer thermal regulator based on the structural phase transition in crystalline polyethylene nanofibers. This structural phase transition represents a dramatic change in morphology from a highly ordered all-trans conformation to a combined trans and gauche conformation with rotational disorder, leading to an abrupt change in phonon transport along the molecular chains. For five nanofiber samples measured here, we observe an average thermal switching ratio of ~8× and maximum switching ratio of ~10×, which occurs in a narrow temperature range of 10 K across the structural phase transition. To the best of our knowledge, the ~10× switching ratio exceeds any reported experimental values for solid-solid and solid-liquid phase transitions of materials. There is no thermal hysteresis observed upon heating/cooling cycles.
RESUMO
Coherent thermal emission deviates from the Planckian blackbody emission with a narrow spectrum and strong directionality. While far-field thermal emission from polaritonic resonance has shown the deviation through modelling and optical characterizations, an approach to achieve and directly measure dominant coherent thermal emission has not materialised. By exploiting the large disparity in the skin depth and wavelength of surface phonon polaritons, we design anisotropic SiO2 nanoribbons to enable independent control of the incoherent and coherent behaviours, which exhibit over 8.5-fold enhancement in the emissivity compared with the thin-film limit. Importantly, this enhancement is attributed to the coherent polaritonic resonant effect, hence, was found to be stronger at lower temperature. A thermometry platform is devised to extract, for the first time, the thermal emissivity from such dielectric nanoemitters with nanowatt-level emitting power. The result provides new insight into the realisation of spatial and spectral distribution control for far-field thermal emission.
RESUMO
Biliary atresia (BA) results in severe bile blockage and is caused by the absence of extrahepatic ducts. Even after successful hepatic portoenterostomy, a considerable number of patients are likely to show progressive deterioration in liver function. Recent studies show that mutations in protein-coding mitochondrial DNA (mtDNA) genes and/or mitochondrial genes in nuclear DNA (nDNA) are associated with hepatocellular dysfunction. This observation led us to investigate whether hepatic dysfunctions in BA is genetically associated with mtDNA mutations. We sequenced the mtDNA protein-coding genes in 14 liver specimens from 14 patients with BA and 5 liver specimens from 5 patients with choledochal cyst using next-generation sequencing. We found 34 common non-synonymous variations in mtDNA protein-coding genes in all patients examined. A systematic 3D structural analysis revealed the presence of several single nucleotide polymorphism-like mutations in critical regions of complexes I to V, that are involved in subunit assembly, proton-pumping activity, and/or supercomplex formation. The parameters of chronic hepatic injury and liver dysfunction in BA patients were also significantly correlated with the extent of hepatic failure, suggesting that the mtDNA mutations may aggravate hepatopathy. Therefore, mitochondrial mutations may underlie the pathological mechanisms associated with BA.
Assuntos
Atresia Biliar/genética , Colestase/genética , DNA Mitocondrial/genética , Genes Mitocondriais/genética , Hepatopatias/genética , Mitocôndrias/genética , Mutação/genética , Ductos Biliares/patologia , Feminino , Humanos , Lactente , Fígado/patologia , Masculino , Portoenterostomia Hepática/métodosRESUMO
Printing techniques could offer a scalable approach to fabricate thermoelectric (TE) devices on flexible substrates for power generation used in wearable devices and personalized thermo-regulation. However, typical printing processes need a large concentration of binder additives, which often render a detrimental effect on electrical transport of the printed TE layers. Here, we report scalable screen-printing of TE layers on flexible fiber glass fabrics, by rationally optimizing the printing inks consisting of TE particles (p-type Bi0.5Sb1.5Te3 or n-type Bi2Te2.7Se0.3), binders, and organic solvents. We identified a suitable binder additive, methyl cellulose, which offers suitable viscosity for printability at a very small concentration (0.45-0.60 wt.%), thus minimizing its negative impact on electrical transport. Following printing, the binders were subsequently burnt off via sintering and hot pressing. We found that the nanoscale defects left behind after the binder burnt off became effective phonon scattering centers, leading to low lattice thermal conductivity in the printed n-type material. With the high electrical conductivity and low thermal conductivity, the screen-printed TE layers showed high room-temperature ZT values of 0.65 and 0.81 for p-type and n-type, respectively.
RESUMO
There is currently little information on nonphosphorylated sugar epimerases, which are of potential interest for producing rare sugars. We found a gene (the TM0416 gene) encoding a putative d-tagatose-3-epimerase-related protein from the hyperthermophilic bacterium Thermotoga maritima We overexpressed the TM0416 gene in Escherichia coli and purified the resulting recombinant protein for detailed characterization. Amino acid sequence alignment and a structural similarity search revealed that TM0416 is a putative nonphosphorylated sugar epimerase. The recombinant enzyme exhibited maximal C-3 epimerization of l-ribulose to l-xylulose at â¼80°C and pH 7 in the presence of 1 mM Mn2+ In addition, this enzyme showed unusually high activity for the epimerization of d-tagatose to d-sorbose, with a conversion yield of 20% after 6 h at 80°C. Remarkably, the enzyme catalyzed the isomerization of d-erythrose or d-threose to d-erythrulose significantly, with conversion yields of 71% and 54.5%, respectively, after 6 h at 80°C at pH 7. To further investigate the substrate specificity of TM0416, we determined its crystal structures in complex with divalent metal ions and l-erythrulose at resolutions of 1.5 and 1.6 Å. Detailed inspection of the structural features and biochemical data clearly demonstrated that this metalloenzyme, with a freely accessible substrate-binding site and neighboring hydrophobic residues, exhibits different and promiscuous substrate preferences, compared with its mesophilic counterparts. Therefore, this study suggests that TM0416 can be functionally classified as a novel type of l-ribulose 3-epimerase (R3E) with d-erythrose isomerase activity.IMPORTANCE Rare sugars, which occur naturally in small amounts, have attracted considerable attention in the food and drug industries. However, there is little information on nonphosphorylated sugar epimerases, which might potentially be applied for the production of rare sugars. This study describes the characterization and functional annotation of a putative nonphosphorylated sugar 3-epimerase from a hyperthermophilic bacterium. Furthermore, we determined its crystal structures in complex with divalent metal ions and l-erythrulose, highlighting its metal-dependent, bifunctional, sugar-isomerizing activity. This hyperthermophilic R3E exhibited d-erythrose/d-threose isomerase activity, with structural features near the substrate-binding site distinct from those of its mesophilic counterparts. Moreover, this metalloenzyme showed unusually high activity for the epimerization of d-tagatose to d-sorbose at 70°C. Therefore, TM0416 can be functionally classified as a novel type of promiscuous R3E with a potential for the production of rare sugars for the food and pharmaceutical industries.
Assuntos
Proteínas de Bactérias/química , Proteínas de Bactérias/metabolismo , Carboidratos Epimerases/química , Hexoses/metabolismo , Thermotoga maritima/enzimologia , Sequência de Aminoácidos , Proteínas de Bactérias/genética , Carboidratos Epimerases/genética , Carboidratos Epimerases/metabolismo , Catálise , Domínio Catalítico , Cristalografia por Raios X , Estabilidade Enzimática , Dados de Sequência Molecular , Alinhamento de Sequência , Especificidade por Substrato , Thermotoga maritima/química , Thermotoga maritima/genética , Thermotoga maritima/metabolismoRESUMO
Thermophilic l-arabinose isomerase (AI), which catalyzes the interconversion of l-arabinose and l-ribulose, can be used to produce d-tagatose, a sugar substitute, from d-galactose. Unlike mesophilic AIs, thermophilic AIs are highly dependent on divalent metal ions for their catalytic activity and thermostability at elevated temperatures. However, the molecular basis underlying the substrate preferences and metal requirements of multimeric AIs remains unclear. Here we report the first crystal structure of the apo and holo forms of thermophilic Geobacillus kaustophilus AI (GKAI) in hexamer form. The structures, including those of GKAI in complex with l-arabitol, and biochemical analyses revealed not only how the substrate-binding site of GKAI is formed through displacement of residues at the intersubunit interface when it is bound to Mn(2+), but also revealed the water-mediated H-bonding networks that contribute to the structural integrity of GKAI during catalysis. These observations suggest metal-mediated isomerization reactions brought about by intersubunit interactions at elevated temperatures are responsible for the distinct active site features that promote the substrate specificity and thermostability of thermophilic AIs.
Assuntos
Aldose-Cetose Isomerases/química , Proteínas de Bactérias/química , Geobacillus/enzimologia , Temperatura Alta , Manganês/química , Cristalografia por Raios X , Estabilidade Enzimática , Ligação de Hidrogênio , Estrutura Quaternária de ProteínaRESUMO
UDP-galactose 4-epimerase (GalE) catalyzes the interconversion of UDP-glucose (UDP-Glc) and UDP-galactose (UDP-Gal), which is a pivotal step in the Leloir pathway for d-galactose metabolism. Although GalE is widely distributed in prokaryotes and eukaryotes, little information is available regarding hyperthermophilic GalE. We overexpressed the TM0509 gene, encoding a putative GalE from Thermotoga maritima (TMGalE), in Escherichia coli and characterized the encoded protein. To further investigate the molecular basis of this enzyme's catalytic function, we determined the crystal structures of TMGalE and TMGalE bound to UDP-Glc at resolutions of 1.9 Å and 2.0 Å, respectively. The enzyme was determined to be a homodimer with a molecular mass of 70 kDa. The enzyme could reversibly catalyze the epimerization of UDP-GalNAc/UDP-GlcNAc as well as UDP-Gal/UDP-Glc at elevated temperatures, with an apparent optimal temperature and pH of 80 °C and 7.0, respectively. Our data showed that TM0509 is a UDP-galactosugar 4-epimerase involved in d-galactose metabolism; consequently, this study provides the first detailed characterization of a hyperthermophilic GalE. Moreover, the promiscuous substrate specificity of TMGalE, which is more similar to human GalE than E. coli GalE, supports the notion that TMGalE might exhibit the earliest form of sugar-epimerizing enzymes in the evolution of galactose metabolism.
Assuntos
Proteínas de Bactérias/química , Thermotoga maritima/química , UDPglucose 4-Epimerase/química , Uridina Difosfato Galactose/química , Uridina Difosfato Glucose/química , Sequência de Aminoácidos , Proteínas de Bactérias/antagonistas & inibidores , Proteínas de Bactérias/genética , Evolução Biológica , Domínio Catalítico , Cristalografia por Raios X , Escherichia coli/genética , Escherichia coli/metabolismo , Expressão Gênica , Temperatura Alta , Cinética , Modelos Moleculares , Dados de Sequência Molecular , Filogenia , Multimerização Proteica , Estrutura Secundária de Proteína , Proteínas Recombinantes/química , Proteínas Recombinantes/genética , Alinhamento de Sequência , Especificidade por Substrato , Thermotoga maritima/classificação , Thermotoga maritima/enzimologia , UDPglucose 4-Epimerase/antagonistas & inibidores , UDPglucose 4-Epimerase/genéticaRESUMO
The gadB gene encoding glutamate decarboxylase (GAD) from Lactobacillus plantarum was cloned and expressed in Escherichia coli. The recombinant enzyme exhibited maximal activity at 40 °C and pH 5.0. The 3D model structure of L. plantarum GAD proposed that its C-terminal region (Ile454-Thr468) may play an important role in the pH dependence of catalysis. Accordingly, C-terminally truncated (Δ3 and Δ11 residues) mutants were generated and their enzyme activities compared with that of the wild-type enzyme at different pH values. Unlike the wild-type GAD, the mutants showed pronounced catalytic activity in a broad pH range of 4.0-8.0, suggesting that the C-terminal region is involved in the pH dependence of GAD activity. Therefore, this study may provide effective target regions for engineering pH dependence of GAD activity, thereby meeting industrial demands for the production of γ-aminobutyrate in a broad range of pH values.
Assuntos
Proteínas de Bactérias/química , Glutamato Descarboxilase/química , Lactobacillus plantarum/enzimologia , Motivos de Aminoácidos , Proteínas de Bactérias/genética , Proteínas de Bactérias/metabolismo , Biocatálise , Estabilidade Enzimática , Glutamato Descarboxilase/genética , Glutamato Descarboxilase/metabolismo , Concentração de Íons de Hidrogênio , Lactobacillus plantarum/química , Lactobacillus plantarum/genética , Ácido gama-Aminobutírico/metabolismoRESUMO
The optimal hybridization of photovoltaic (PV) and thermoelectric (TE) devices has long been considered ideal for the efficient harnessing solar energy. Our hybrid approach uses full spectrum solar energy via lossless coupling between PV and TE devices while collecting waste energy from thermalization and transmission losses from PV devices. Achieving lossless coupling makes the power output from the hybrid device equal to the sum of the maximum power outputs produced separately from individual PV and TE devices. TE devices need to have low internal resistances enough to convey photo-generated currents without sacrificing the PV fill factor. Concomitantly, a large number of p-n legs are preferred to drive a high Seebeck voltage in TE. Our simple method of attaching a TE device to a PV device has greatly improved the conversion efficiency and power output of the PV device (~30% at a 15°C temperature gradient across a TE device).