Evaporation-Rate Control of Water Droplets on Flexible Transparent Heater for Sensor Application.

To develop high-performance de- or anti-frosting/icing devices based on transparent heaters, it is necessary to study the evaporation-rate control of droplets on heater surfaces. However, almost no research has been done on the evaporation-rate control of liquid droplets on transparent heaters. In this study, we investigate the evaporation characteristics of water droplets on transparent heater surfaces and determine that they depend upon the surface wettability, by modifying which, the complete evaporation time can be controlled. In addition, we study the defrosting and deicing performances through the surface wettability, by placing the flexible transparent heater on a webcam. The obtained results can be used as fundamental data for the transparent defrosting and deicing systems of closed-circuit television (CCTV) camera lenses, smart windows, vehicle backup cameras, aircraft windows, and sensor applications.

Rapid Low-Temperature 3D Integration of Silicon Nanowires on Flexible Substrates.

The vertical integration of 1D nanostructures onto the 2D substrates has the potential to offer significant performance gains to flexible electronic devices due to high integration density, large surface area, and improved light absorption and trapping. A simple, rapid, and low temperature transfer bonding method has been developed for this purpose. Ultrasonic vibration is used to achieve a low temperature bonding within a few seconds, resulting in a polymer-matrix-free, electrically conducting vertical assembly of silicon nanowires (SiNWs) with a graphene/PET substrate. The microscopic structure, and mechanical and electrical characteristics of the interface between the transferred SiNW array and graphene layer are subsequently investigated, revealing that this creates a mechanically robust and electrically Ohmic contact. This newly developed ultrasonic transfer bonding technique is also found to be readily adaptable for diverse substrates of both metal and polymer. It is therefore considered as a valuable technique for integrating 1D vertical nanostructures onto the 2D flexible substrates for flexible photovoltaics, energy storage, and water splitting systems.

Carrier Trap and Their Effects on the Surface and Core of AlGaN/GaN Nanowire Wrap-Gate Transistor.

We used capacitance-voltage (C-V), conductance-voltage (G-V), and noise measurements to examine the carrier trap mechanisms at the surface/core of an AlGaN/GaN nanowire wrap-gate transistor (WGT). When the frequency is increased, the predicted surface trap density promptly drops, with values ranging from 9.1 × 1013 eV-1∙cm-2 at 1 kHz to 1.2 × 1011 eV-1∙cm-2 at 1 MHz. The power spectral density exhibits 1/f-noise behavior in the barrier accumulation area and rises with gate bias, according to the 1/f-noise features. At lower frequencies, the device exhibits 1/f-noise behavior, while beyond 1 kHz, it exhibits 1/f2-noise behavior. Additionally, when the fabricated device governs in the deep-subthreshold regime, the cutoff frequency for the 1/f2-noise features moves to the subordinated frequency (~102 Hz) side.

Numerical simulation and biomechanical analysis of locking screw caps on clavicle locking plates.

BACKGROUND: The risk of displaced and comminuted midshaft clavicle fractures is increased in high-energy traumas such as sport injuries and traffic accidents. Open reduction and plate fixation have been widely used for midshaft clavicle fractures. Among various plates for clavicle shaft fractures, superior locking compression plates (LCPs) have been mostly used. In plate fixation, nonunion caused by implant failure is the most difficult complication. The most common reasons for metal plate failure are excessive stress and stress concentration caused by cantilever bending. These causes were easily addressed using a locking screw cap (LSC). METHODS: The clavicle 3-dimensional image was made from a computed tomography scan, and the clavicle midshaft fracture model was generated with a 10-mm interval. The fracture model was fixed with a superior LCP, and finite element analysis was conducted between the presence (with LSC model) and absence (without LSC model) of an LSC on the site of the fracture. The stresses of screw holes in models with and without LSCs were measured under 3 forces: 100 N cantilever bending force, 100 N axial compression force, and 1 N·m axial torsion force. After the finite element analysis, a validation test was conducted on the cantilever bending force known as the greatest force applied to superior locking plates. RESULTS: The mean greatest stress under the cantilever bending force was significantly greater than other loading forces. The highest stress site was the screw hole edge on the fracture site in both models under the cantilever bending and axial compression forces. Under the axial torsional force, the maximum stress point was the lateral first screw hole edge. The ultimate plate stress of the with LSC model is completely lower than that of the without LSC model. According to the validation test, the stiffness, ultimate load, and yield load of the with LSC model were higher than those of the without LSC model. CONCLUSIONS: Therefore, inserting an LSC into an empty screw hole in the fracture area reduces the maximum stress on an LCP and improves biomechanical stability.

Viscosity-Controllable Graphene Oxide Colloids Using Electrophoretically Deposited Graphene Oxide Sheets.

Graphene oxide (GO) is one of the interesting ink materials owing to its fascinating properties, such as high dissolubility in water and high controllable electric properties. For versatile printing application, the viscosity of GO colloids should be controlled in order to meet the specific process requirements. Here, we report on the relatively rapid fabrication of viscosity-increased GO (VIGO) colloids mixed with electrophoretically deposited GO sheets (EPD-GO). As the GO colloid concentration, applied voltage, and deposition time increase, the viscosity of the GO colloids becomes high. The reason for the improved viscosity of GO colloids is because EPD-GO has parallel stacked GO sheets. The GO and VIGO colloids are compared and characterized using various chemical and structural analyzers. Consequently, our simple and fast method for the fabrication of GO colloids with enhanced viscosity can be used for producing inks for flexible and printed electronics.