Bilateral Production Shield Enabling Highly Efficient Perovskite Photovoltaics.

Enhancing the intrinsic stability of perovskite and through encapsulation to isolate water, oxygen, and UV-induced decomposition are currently common and most effective strategies in perovskite solar cells. Here, the atomic layer deposition process is employed to deposit a nanoscale (≈100 nm), uniform, and dense Al2O3 film on the front side of perovskite devices, effectively isolating them from the erosion caused by water and oxygen in the humid air. Simultaneously, nanoscale (≈100 nm) TiO2 films are also deposited on the glass surface to efficiently filter out the ultraviolet (UV) light in the light source, which induces degradation in perovskite. Ultimately, throughthe collaborative effects of both aspects, the stability of the devices is significantly improved under conditions of humid air and illumination. As a result, after storing the devices in ambient air for 1000 h, the efficiency only declines to 95%, and even after 662 h of UV exposure, the efficiency remains at 88%, far surpassing the performance of comparison devices. These results strongly indicate that the adopted Al2O3 and TiO2 thin films play a significant role in enhancing the stability of perovskite solar cells, demonstrating substantial potential for widespread industrial applications.

Dual-Stage Reduction Strategy of Tin Perovskite Enables High Performance Photovoltaics.

The rapid oxidation of Sn2+ in tin-based perovskite solar cells (TPSCs) restricts their efficiency and stability have been main bottleneck towards further development. This study developed a novel strategy which utilizes thiosulfate ions (S2O32-) in the precursor solution to enable a dual-stage reduction process. In the solution stage, thiosulfate acted as an efficacious reducing agent to reduce Sn4+ to Sn2+, meanwhile, its oxidation products were able to reduce I2 to I- during the film stage. This dual reduction ability effectively inhibited the oxidation of Sn2+ and passivated defects, further promising an excellent stability of the perovskite devices. As a result, thiosulfate-incorporated devices achieved a high efficiency of 14.78% with open-circuit voltage reaching 0.96 V. The stability of the optimized devices achieved a remarkable improvement, maintaining 90% of their initial efficiencies after 628 hours at maximum-power-point (MPP). The findings provid research insights and experimental data support for the sustained dynamic reduction in TPSCs.

Vertically Concentrated Quantum Wells Enabling Highly Efficient Deep-Blue Perovskite Light-Emitting Diodes.

Deep-blue perovskite light-emitting diodes (PeLEDs) based on quasi-two-dimensional (quasi-2D) systems exist heightened sensitivity to the domain distribution. The top-down crystallization mode will lead to a vertical gradient distribution of quantum well (QW) structure, which is unfavorable for deep-blue emission. Herein, a thermal gradient annealing treatment is proposed to address the polydispersity issue of vertical QWs in quasi-2D perovskites. The formation of large-n domains at the upper interface of the perovskite film can be effectively inhibited by introducing a low-temperature source in the annealing process. Combined with the utilization of NaBr to inhibit the undesirable n=1 domain, a vertically concentrated QW structure is ultimately attained. As a result, the fabricated device delivers a narrow and stable deep-blue emission at 458 nm with an impressive external quantum efficiency (EQE) of 5.82 %. Green and sky-blue PeLEDs with remarkable EQE of 21.83 % and 17.51 % are also successfully achieved, respectively, by using the same strategy. The findings provide a universal strategy across the entire quasi-2D perovskites, paving the way for future practical application of PeLEDs.

Surficial Homogenic Effect Enables Highly Stable Deep-Blue Perovskite Light-Emitting Diodes.

The device performance of deep-blue perovskite light-emitting diodes (PeLEDs) is primarily constrained by low external quantum efficiency (EQE) especially poor operational stability. Herein, we develop a facile strategy to improve deep-blue emission through rational interface engineering. We innovatively reported the novel electron transport material, 4,6-Tris(4-(diphenylphosphoryl)phenyl)-1,3,5-triazine (P-POT2T), and utilized a sequential wet-dry deposition method to form homogenic gradient interface between electron transport layer (ETL) and perovskite surface. Unlike previous reports that achieved carrier injection balance by inserting new interlayers, our strategy not only passivated uncoordinated Pb in the perovskite via P=O functional groups but also reduced interfacial carrier recombination without introducing new interfaces. Additionally, this strategy enhanced the interface contact between the perovskite and ETL, significantly boosting device stability. Consequently, the fabricated deep-blue PeLEDs delivered an external quantum efficiency (EQE) exceeding 5% (@ 460 nm) with an exceptional halftime extended to 31.3 minutes. This straightforward approach offers a new strategy to realize highly efficient especially stable PeLEDs.

Electronically Manipulated Molecular Strategy Enabling Highly Efficient Tin Perovskite Photovoltaics.

Buried interface modification can effectively improve the compatibility between interfaces. Given the distinct interface selections in perovskite solar cells (PSCs), the applicability of a singular modification material remains limited. Consequently, in response to this challenge, we devised a tailored molecular strategy based on the electronic effects of specific functional groups. Therefore, we prepared three distinct silane coupling agents, and due to the varying inductive effects of these functional groups, the electronic distribution and molecular dipole moments of the coupling agents are correspondingly altered. Among them, trimethoxy (3,3,3-trifluoropropyl)-silane (F3 -TMOS), which possesses electron-withdrawing groups, generates a molecular dipole moment directed toward the hole transport layer (HTL). This approach changes the work function of the HTL, optimizes the energy level alignment, reduces the open-circuit voltage loss, and facilitates carrier transport. Furthermore, through the buffering effect of the coupling agent, the interface strain and lattice distortion caused by annealing the perovskite are reduced, enhancing the stability of the tin-based perovskite. Encouragingly, tin PSCs treated with F3 -TMOS achieved a champion efficiency of 14.67 %. This strategy provides an expedient avenue for the design of buried interface modification materials, enabling precise molecular adjustments in accordance with distinct interfacial contexts to ameliorate mismatched energetics and enhance carrier dynamics.

Removal of Residual Additive Enabling Perfect Crystallization of Photovoltaic Perovskites.

Achieving high-efficiency perovskite solar cells (PSCs) hinges on the precise control of the perovskite film crystallization process, often improved by the inclusion of additives. While dimethyl sulfoxide (DMSO) is traditionally used to manage this process, its removal from the films is problematic. In this work, methyl phenyl sulfoxide (MPSO) was employed instead of DMSO to slow the crystallization rate, as MPSO is more easily removed from the perovskite structure. The electron delocalization associated with the benzene ring in MPSO decreases the electron density around the oxygen atom in the sulfoxide group, thus reducing its interaction with PbI2. This strategy not only sustains the formation of a crystallization-slowing intermediate phase but also simplifies the elimination of the additive. Consequently, the optimized PSCs achieved a leading power conversion efficiency (PCE) of 25.95% along with exceptional stability. This strategy provides a novel method for fine-tuning perovskite crystallization to enhance the overall performance of photovoltaic devices.

Chemical Reaction Modulated Low-Dimensional Phase Toward Highly Efficient Sky-Blue Perovskite Light-Emitting Diodes.

Blue perovskite light-emitting diodes (PeLEDs) are crucial avenues for achieving full-color displays and lighting based on perovskite materials. However, the relatively low external quantum efficiency (EQE) has hindered their progression towards commercial applications. Quasi-two-dimensional (quasi-2D) perovskites stand out as promising candidates for blue PeLEDs, with optimized control over low-dimensional phases contributing to enhanced radiative properties of excitons. Herein, the impact of organic molecular dopants on the crystallization of various n-phase structures in quasi-2D perovskite films. The results reveal that the highly reactive bis(4-(trifluoromethyl)phenyl)phosphine oxide (BTF-PPO) molecule could effectively restrain the formation of organic spacer cation-ordered layered perovskite phases through chemical reactions, simultaneously passivate those uncoordinated Pb2+ defects. Consequently, the prepared PeLEDs exhibited a maximum EQE of 16.6 % (@ 490 nm). The finding provides a new route to design dopant molecules for phase modulation in quasi-2D PeLEDs.

Clinical manifestations and early effectiveness of methimazole in patients with graves' hyperthyroidism-related severe hepatic dysfunction.

BACKGROUND: Graves' hyperthyroidism (GH) is often accompanied by mild to moderate liver injury, but severe hepatic dysfunction (SHD) is relatively rare. Whether patients with GH-related SHD can be treated with methimazole (MMI) remains controversial. This study aimed to determine the clinical characteristics and to evaluate the role of low-dose MMI for such patients. METHODS: 33 patients with GH-related SHD were selected for this retrospective study in the Fifth Medical Center of Chinese PLA General Hospital from January 2017 to July 2022. The clinical manifestations, therapeutic responses, and effectiveness of MMI were evaluated. RESULTS: Systemic jaundice (100.0%), yellow urine (100.0%), fatigue (87.9%), and goiter (66.7%) were the main symptoms. Total bilirubin (TBIL) had no linear correlation with free triiodothyronine (FT3) (r = -0.023, p = .899), free thyroxine (FT4) (r = 0.111, p = .540), T3 (r = -0.144, p = .425), and T4 (r = 0.037, p = .837). On the 14th day after admission, FT3, FT4, T3, T4, TBIL, direct bilirubin (DBIL), alanine transaminase (ALT), aspartate transaminase (AST), alkaline phosphatase (ALP), γ-glutamyltransferase (GGT), and international normalized ratio (INR) decreased compared with the baseline (p < .05). The decrease rates of FT3, FT4, T3, T4, TBIL, and DBIL in the MMI group were higher than those in the non-MMI group (p < .05). The improvement rate of the MMI group (77.8%) was higher than that of the non-MMI group (9.5%, p = .001). MMI treatment is an independent predictor affecting the early improvement of patients (OR = 0.022, p = .010). CONCLUSIONS: The main clinical manifestations of patients with GH-related SHD were symptoms related to liver disease. Low-dose MMI was safe and effective for them.

Oxidation of Sb(III) by Shewanella species with the assistance of extracellular organic matter.

Antimony (Sb) is a toxic substance that poses a serious ecological threat when released into the environment. The species and redox state of Sb determine its environmental toxicity and fate. Understanding the redox transformations and biogeochemical cycling of Sb is crucial for analyzing and predicting its environmental behavior. Dissolved organic matter (DOM) in the environment greatly affects the fate of Sb. Microbially produced DOM is a vital component of environmental DOM; however, its specific role in Sb(III) oxidation has not been experimentally confirmed. In this work, the oxidation capacity of several Shewanella strains and their derived DOM to Sb(III) was confirmed. The oxidation rate of Sb(III) shows a positive correlation with DOM concentration, with higher rates observed under neutral and weak alkaline conditions, regardless of the presence of light. Incubation experiments indicated that extracellular enzymes and common reactive oxygen species were not involved in the oxidation of Sb(III). Characteristics of DOM suggests that microbial humic acid-like and fulvic acid-like substances are the potential contributors to Sb(III) oxidation. These findings not only experimentally validate the role of bacterial-derived DOM in Sb(III) oxidation but also reveal the significance of Shewanella and biogenic DOM in the biogeochemical cycling of Sb.

Low-Dimensional Phase Regulation to Restrain Non-Radiative Recombination for Sky-Blue Perovskite LEDs with EQE Exceeding 15 .

Achieving efficient blue electroluminescence (EL) remains the fundamental challenge that impedes perovskite light-emitting diodes (PeLEDs) towards commercial applications. The bottleneck accounting for the inefficient blue PeLEDs is broadly attributed to the poor-emissive blue perovskite emitters based on either mixed halide engineering or reduced-dimensional strategy. Herein, we report the high-performing sky-blue PeLEDs (490 nm) with the maximum EQE exceeding 15 % by incorporating a molecular modifier, namely 4,4'-Difluorophenone, for significantly suppressing the non-radiative recombination and tuning of the low-dimensional phase distribution of quasi-2D blue perovskites, which represents a remarkable paradigm for developing the new generation of blue lighting sources.

Stabilized Low-Dimensional Species for Deep-Blue Perovskite Light-Emitting Diodes with EQE Approaching 3.4.

Despite recent encouraging developments, achieving efficient blue perovskite light-emitting diodes (PeLEDs) have been widely considered a critical challenge. The efficiency breakthrough only occurred in the sky-blue region, and the device performance of pure-blue and deep-blue PeLEDs lags far behind those of their sky-blue counterparts. To avoid the negative effects associated with dimensionality reduction and excess chloride typically needed to achieve deep-blue emission, here we demonstrate guanidine (GA+)-induced deep-blue (∼457 nm) perovskite emitters enabling spectrally stable PeLEDs with a record external quantum efficiency (EQE) over 3.41% through a combination of quasi-2D perovskites and halide engineering. Owing to the presence of GA+, even a small inclusion of chloride ions is sufficient for generating deep-blue electroluminescence (EL), in clear contrast to the previously reported deep-blue PeLEDs with significant chloride inclusion that negatively affects spectral stability. Based on the carrier dynamics analysis and theoretical calculation, GA+ is found to stabilize the low-dimensional species during annealing, retarding the cascade energy transfer and facilitating the deep-blue EL. Our findings open a potential third route to achieve deep-blue PeLEDs beyond the conventional methods of dimensionality reduction and excessive chloride incorporation.

Visualizing the Surface Photocurrent Distribution in Perovskite Photovoltaics.

Defect states play an important role in the photovoltaic performance of metal halide perovskites. Particularly, the passivation of surface defects has made great contributions to high-performance perovskite photovoltaics. This highlights the importance of understanding the surface defects from a fundamental level by developing more accurate and operando characterization techniques. Herein, a strategy to enable the surface carriers and photocurrent distributions on perovskite films to be visualized in the horizontal direction is put forward. The visual image of photocurrent distribution is realized by combining the static local distribution of carriers provided by scanning near-field optical microscopy with the dynamic transporting of carriers achieved via a scanning photocurrent measurement system. Taking a surface passivated molecule as an example, a comprehensive defect scene including static and dynamic as well as local and entire conditions is obtained using this strategy. The comprehensive analysis of the trap states in perovskite films is pioneered vertically and horizontally, which will powerfully promote the deep understanding of defect mechanisms and carrier behavior for the goal of fabricating high-performance perovskite optoelectronic devices.

Detection and Quantification of Antimicrobial-Resistant Cells in Aquatic Environments by Bioorthogonal Noncanonical Amino Acid Tagging.

Aquatic environments are important reservoirs of antibiotic wastes, antibiotic resistance genes, and bacteria, enabling the persistence and proliferation of antibiotic resistance in different bacterial populations. To prevent the spread of antibiotic resistance, effective approaches to detect antimicrobial susceptibility in aquatic environments are highly desired. In this work, we adopt a metabolism-based bioorthogonal noncanonical amino acid tagging (BONCAT) method to detect, visualize, and quantify active antimicrobial-resistant bacteria in water samples by exploiting the differences in bacterial metabolic responses to antibiotics. The BONCAT approach can be applied to rapidly detect bacterial resistance to multiple antibiotics within 20 min of incubation, regardless of whether they act on proteins or DNA. In addition, the combination of BONCAT with the microscope enables the intuitive characterization of antibiotic-resistant bacteria in mixed systems at single-cell resolution. Furthermore, BONCAT coupled with flow cytometry exhibits good performance in determining bacterial resistance ratios to chloramphenicol and population heterogeneity in hospital wastewater samples. In addition, this approach is also effective in detecting antibiotic-resistant bacteria in natural water samples. Therefore, such a simple, fast, and efficient BONCAT-based approach will be valuable in monitoring the increase and spread of antibiotic resistance within natural and engineered aquatic environments.

Single-Layered MXene Nanosheets Doping TiO2 for Efficient and Stable Double Perovskite Solar Cells.

The inorganic lead-free Cs2AgBiBr6 double perovskite structure is the promising development direction in perovskite solar cells (PSCs) to solve the problem of the instability of the APbX3 structure and lead toxicity. However, the low short-circuit current and power conversion efficiency (PCE) caused by the low crystallization of Cs2AgBiBr6 greatly limit the optoelectronic application. Herein, we adopt a simple strategy to dope single-layered MXene nanosheets into titania (Ti3C2Tx@TiO2) as a multifunctional electron transport layer for stable and efficient Cs2AgBiBr6 double PSCs. The single-layered MXene nanosheets significantly improve the electrical conductivity and electron extraction rate of TiO2; meanwhile, the single-layered MXene nanosheets change the surface wettability of the electron transport layer and promote the crystallization of the Cs2AgBiBr6 double perovskite in solar cell devices. Therefore, the PCE went up by more than 40% to 2.81% compared to that of a TiO2 based device, and the hysteresis was greatly suppressed. Furthermore, the device based on Ti3C2Tx@TiO2 showed the long-term operating stability. After storing the device for 15 days under ambient air conditions, the PCE still remained a retention rate of 93% of the initial one. Our finding demonstrates the potential of Ti3C2Tx@TiO2 in electron transfer material of high-performance double PSCs.

Recent progress in induced pluripotent stem cell-derived 3D cultures for cardiac regeneration.

Cardiovascular diseases are the leading cause of death in the world due to the high incidence of the diseases coupled with the limited therapeutic options. In recent years, advances in regenerative medicine have emerged as a promising treatment. Differentiation of induced pluripotent stem cells (iPSCs) into cardiac cells and emerging technologies allowing arrangement of cells into complex 3D tissue-like structures open new frontiers for transplantation and engraftment of these tissue patches onto the damaged heart. Despite the cells integrating and presenting initial neovascularization, the functional and electric properties of these patches are still not comparable with those of the host cardiac tissue. Future research optimizing maturation and integration of the iPSC-derived cardiomyocytes is paramount for cardiac cell therapy to attain clinical use. Herein, we will review the state of the art and the different approaches to constructing these 3D transplantable structures.

MicroRNAs play important roles in regulating the rapid growth of the Phyllostachys edulis culm internode.

Moso bamboo (Phyllostachys edulis) is a fast-growing species with uneven growth and lignification from lower to upper segments within one internode. MicroRNAs (miRNAs) play a vital role in post-transcriptional regulation in plants. However, how miRNAs regulate fast growth in bamboo internodes is poorly understood. In this study, one moso bamboo internode was divided during early rapid growth into four segments called F4 (bottom) to F1 (upper) and these were then analysed for transcriptomes, miRNAs and degradomes. The F4 segment had a higher number of actively dividing cells as well as a higher content of auxin (IAA), cytokinin (CK) and gibberellin (GA) compared with the F1 segment. RNA-seq analysis showed DNA replication and cell division-associated genes highly expressed in F4 rather than in F1. In total, 63 miRNAs (DEMs) were identified as differentially expressed between F4 and F1. The degradome and the transcriptome indicated that many downstream transcription factors and hormonal responses genes were modulated by DEMs. Several miR-target interactions were further validated by tobacco co-infiltration. Our findings give new insights into miRNA-mediated regulatory pathways in bamboo, and will contribute to a comprehensive understanding of the molecular mechanisms governing rapid growth.

Potassium-Presenting Zinc Oxide Surfaces Induce Vertical Phase Separation in Fullerene-Free Organic Photovoltaics.

Bulk heterojunction (BHJ) structure based organic photovoltaics (OPVs) have recently showed great potential for achieving high power conversion efficiencies (PCEs). An ideal BHJ structure would feature large donor/acceptor interfacial areas for efficient exciton dissociation and gradient distributions with high donor and acceptor concentrations near the anode and cathode, respectively, for efficient charge extraction. However, the random mixing of donors and acceptors in the BHJ often suffers the severe charge recombination in the interface, resulting in poor charge extraction. Herein, we propose a new approach-treating the surface of the zinc oxide (ZnO) as an electron transport layer with potassium hydroxide-to induce vertical phase separation of an active layer incorporating the nonfullerene acceptor IT-4F. Density functional theory calculations suggested that the binding energy difference between IT-4F and the PBDB-T-2Cl, to the potassium (K)-presenting ZnO interface, is twice as strong as that for IT-4F and PBDB-T-2Cl to the untreated ZnO surface, such that it would induce more IT-4F moving toward the K-presenting ZnO interface than the untreated ZnO interface thermodynamically. Benefiting from efficient charge extraction, the best PCEs increased to 12.8% from 11.8% for PBDB-T-2Cl:IT-4F-based devices, to 12.6% from 11.6% for PBDB-T-2Cl:Y1-4F-based devices, to 13.5% from 12.2% for PBDB-T-2Cl:Y6-based devices, and to 15.7% from 15.1% for PM6:Y6-based devices.

[Clinical efficacy of Bushen Huoxue Culuan Formula in treatment of infertility caused by diminished ovarian reserve due to kidney deficiency and blood stasis].

To study the clinical efficacy and safety of Bushen Huoxue Culuan Formula in treating infertility caused by diminished ovarian reserve(DOR) with kidney deficiency and blood stasis. A total of 100 DOR patients treated at Xiyuan Hospital, Acupuncture Hospital and Clinic of China Academy of Chinese Medical Sciences from 2017 to 2020 in line with the inclusion criteria were selected and randomly divided into experimental group and control group at the ratio of 1∶1. The experimental group was treated with Bushen Huoxue Culuan Formular, while the control group was treated with Climen and Clomiphene for 3 menstrual cycles. The ovulation rate, pregnancy rate, pregnancy success rate, serum hormone levels, and traditional Chinese medicine(TCM) symptom scores were observed in the 2 groups. The total effective rate was 92.00% in the experimental group and 72.00% in the control group, with a statistical difference between the two groups(P<0.01); the experimental group was superior to the control group in reducing FSH level, increasing AMH level, improving TCM symptoms, increasing pregnancy rate and pregnancy success rate, with a significant difference(P<0.05). There was no abnormal safety indicator and adverse reaction. Bushen Huoxue Culuan Formular is effective in treating infertility caused by DOR due to kidney deficiency and blood stasis, with a safety and reliability.

The Doping Mechanism of Halide Perovskite Unveiled by Alkaline Earth Metals.

Halide perovskites are a strong candidate for the next generation of photovoltaics. Chemical doping of halide perovskites is an established strategy to prepare the highest efficiency and most stable perovskite-based solar cells. In this study, we unveil the doping mechanism of halide perovskites using a series of alkaline earth metals. We find that low doping levels enable the incorporation of the dopant within the perovskite lattice, whereas high doping concentrations induce surface segregation. The threshold from low to high doping regime correlates to the size of the doping element. We show that the low doping regime results in a more n-type material, while the high doping regime induces a less n-type doping character. Our work provides a comprehensive picture of the unique doping mechanism of halide perovskites, which differs from classical semiconductors. We proved the effectiveness of the low doping regime for the first time, demonstrating highly efficient methylammonium lead iodide based solar cells in both n-i-p and p-i-n architectures.

Tailored Phase Transformation of CsPbI2Br Films by Copper(II) Bromide for High-Performance All-Inorganic Perovskite Solar Cells.

All-inorganic-based perovskites achieved by replacing the organic component with cesium (Cs) have drawn more attention because of their intrinsic inorganic stability. However, the cell efficiency in all-inorganic perovskite solar cells is still far below that in organic-inorganic hybrid perovskite-based devices. Here, we develop a new strategy to mediate the CsPbI2Br crystallization by directly doping copper(II) bromide (CuBr2) into a perovskite precursor. The incorporation of CuBr2 played a role in retarding the crystallization dynamics process of CsPbI2Br film, resulting in a high-quality all-inorganic perovskite film with enlarged grain size, improved carrier mobilities, and reduced trap states. The fabricated perovskite solar cells delivered a champion power conversion efficiency of 16.15%, which is the highest efficiency in CsPbI2Br based all-inorganic perovskite solar cells and largely higher than 13.24% for pristine CsPbI2Br based device. The developed doping method paves a new route to fabricate high-performance all-inorganic perovskite solar cells.