Structural motifs and biological studies of new antimony(III) iodide complexes with thiones.

Eight new antimony(III) iodide complexes of the heterocyclic thioamides, 2-mercapto-1-methylimidazole (MMI), 2-mercaptobenzimidazole (MBZIM), 5-ethoxy-2-mercaptobenzimidazole (EtMBZIM), 2-mercaptothiazolidine (MTZD), 3-methyl-2-mercaptobenzothiazole (NMeMBZT), 2-mercapto-3,4,5,6-tetrahydropyrimidine (tHPMT), 2-mercaptopyridine (PYT), and 2-mercaptopyrimidine (PMT) of formulas {[SbI(3)(MMI)(2)].MeOH} (1), [SbI(3)(MBZIM)(2)] (2), {[SbI(2)(mu(2)-I)(EtMBZIM)(2)](2).H(2)O} (3), [SbI(3)(MTZD)] (4), [(NMeMBZT)SbI(2)(mu(2)-I)(2)(mu(2)-S-NMeMBZT)SbI(2) (NMeMBZT)] (5), {[SbI(3)(tHPMT)(3)].MeOH} (6), [SbI(3)(PYT)] (7), and [SbI(3)(PMT)(2)] (8), have been synthesized and characterized by elemental analysis, FT-IR spectroscopy, FT-Raman spectroscopy, and TG-DTA analysis. The crystal structures of 3, 4, 5, 6, and 7 were also determined by X-ray diffraction. The complexes show interesting structural motifs. Complex 6 is a monomer, with octahedral (Oh) geometry around the metal ion formed by three sulfur and three iodide atoms. Complexes 3 and 5 are dimers, with a square pyramidal (SP) geometry in each monomeric unit, while complexes 4 and 7 are polymers with pseudotrigonal bipyramidal (psi-TBP). Two or three sulfur atoms from thioamide ligands and three iodide atoms are bound to Sb atoms forming building blocks for the dimers and polymers. Strong intramolecular interactions between mu(2)-I and/or mu(2)-S and Sb atoms stabilize both structures. In dimer complex 5, two terminal iodide and one terminal sulfur atom are bonded to the Sb ion, while two mu(2)-I and one mu(2)-S bridging atoms bridge the metal ions forming psi-Oh geometry. Computational studies using multivariant linear regression (MLR) and artificial neural networks (ANN) and considering biological results (50% inhibitory concentration, IC(50)) as dependent variables derived a theoretical equation for IC(50) values of the complexes studied. The calculated IC(50) values are compared satisfactorily with the experimental inhibitory activity of the complexes measured. Complexes 3-7 were used to study their influence upon the catalytic peroxidation of linoleic acid by the enzyme Lipoxygenase (LOX). Compounds 1-8 were also tested for in vitro cytotoxicity, and they showed mostly a moderate cytostatic activity against a variety of tumor cell lines but comparable with those found for the antimony(III) chloride and bromide complexes, reported earlier [Ozturk et al. Inorg. Chem. 2007, 46, 2861-2866; Ozturk et al. Inorg. Chem. 2009, 48, 2233-2245].

Thermal decomposition studies of the polyhedral oligomeric silsesquioxane, POSSh, and when it is impregnated with the metallocene bis(eta5-cyclopentadienyl)zirconium (IV) dichloride or immobilized on silica.

Thermal decomposition studies of the free polyhedral oligomeric silsesquioxane, POSSh, and when this compound has been impregnated with Cp2ZrCl2 (Cp = eta5-C5H5) or immobilized on SiO2 were conducted using infrared emission spectroscopy (IES) over a 100-1000 degrees C temperature range and by thermogravimetric analysis (TGA). The organic groups in POSS(h) apparently decompose thermally into Si-CH3, Si-H and other fragments. Upon impregnation with Cp2ZrCl2, however, a different thermal decomposition pathway was followed and new infrared emission bands appeared in the 1000-900 cm(-1) region suggesting the formation of Si-O-Zr moieties. When immobilized on SiO2 and subjected to thermal decomposition, the POSSh compound lost its organic groups and the inorganic structure remaining was incorporated into the SiO2 framework.

Vibrational spectra of silsesquioxanes impregnated with the metallocene catalyst bis(eta(5)-cyclopentadienyl)zirconium(IV) dichloride.

FT-IR photoacoustic and Raman spectroscopy have been used to study the interactions between the metallocene catalyst, Cp(2)ZrCl(2) (Cp=eta(5)-C(5)H(5)), and two polyhedral oligomeric silsesquioxanes (POSS) supports. The first silsesquioxane support, POSS(h), contains (beta-hydroxyl)-tertiary amine groups, while in the second one, POSS(u), these -OH groups have been converted into N-(p-toluyl) urethane groups. The vibrational spectra of the Cp(2)ZrCl(2):POSS(h) and Cp(2)ZrCl(2):POSS(u) samples show that the Cp(2)ZrCl(2) catalyst reacts with the C-OH groups of POSS(h) and also interacts with N-H and >CO groups of POSS(u). Furthermore, Cp(2)ZrCl(2) can react with the Si-OH groups of the POSS supports and also interact with the O atoms that are bonded to the benzene rings and the N atoms of the tertiary amines in both silsesquioxanes. As a result of the interactions between Cp(2)ZrCl(2) and the POSS supports, acidic species are generated. The Cp(2)ZrCl(2):POSS(h) mass ratio seems to be an important parameter in the formation of Zr-O bonds and the acidic species.

[Infrared and raman spectra studies of DL-homocysteic acid (DLH) and its lanthanum complex at high external pressure].

DL-Homocysteic acid (DLH, (NH3 )-CH(COOH)-(CH2 )2-SO3-) is extensively in existence as free amino-acid in the central nervous system of mammal. The infrared (IR) and Raman spectra of DL-Homocysteic acid (DLH) and its La complex [La (DLH)2Cl3 . H2O = LaL2] were measured at high external pressure. The DLH has two pressure-induced phase transitions (near 17 kbar and 37 kbar) and three pressure-phase areas below 50 kbar for there are ten intermolecular hydrogen bonds between the DLH molecules. But there is only one pressure-induced phase transition (near 27 kbar) to be observed in the complex LaL2. These show that the ten intermolecular hydrogen bonds of the DLH molecules changed due to the formation of complex LaL2. In infrared spectra, the changing trend of the pressure sensitivities (dv/dp) of symmetry stretching of SO3- in DLH and asymmetry stretching of SO3- in LaL2 are very different from the other vibrational modes when both compounds undergo high external pressure. In infrared spectra, the average pressure sensitivities of symmetry stretching of SO3- are: low-pressure phase area (0.30 cm(-1) x (kbar)(-1)) < middle-pressure phase area (0.32 cmn(-1) (kbar) (-1)) < high-pressure phase area (0.41 cm(-1) x (kbar)(-1)), but 0.86 cm(-1) x (kbar)(-1) (low-pressure phase area) >0.64 cm(-1) x (kbar)(-1) (middle-pressure phase area) >0.26 cm(-1) x (kbar)(-1) (high-pressure phase area) to other vibrational modes in DLH. The average pressure sensitivities of asymmetry stretching of SO3- in LaL2 are lower in low-pressure phase area than in high-pressure phase area, but the average pressure sensitivities of other modes are higher in low-pressure phase area than in high-pressure phase area.

Carbonylmetalloimmunoassay (CMIA) a new type of non-radioisotopic immunoassay. Principles and application to phenobarbital assay.

A new non-radioisotopic immunoassay procedure, which we have termed carbonylmetalloimmunoassay (CMIA), is described. The tracers used in this approach are organometallic carbonyl complexes that can be detected at femtomole levels (300-700 fmol) by Fourier transform infrared (FT-IR) spectroscopy. The validity of the technique has been tested in a phenobarbital assay using as the marker a cyclopentadienylmanganese (I) tricarbonyl (cymantrene) moiety, ethyl acetate extraction to separate the free and bound organometallic fractions, and FT-IR spectroscopy to detect the CO stretching modes of the organometallic label. Typical dilution and standard curves obtained with this CMIA procedure are presented. The method was of comparable sensitivity to a [14C] radioimmunoassay (RIA) for the detection of phenobarbital. A comparison of the results for phenobarbital assays by both CMIA and RIA showed that higher titres were obtained using the CMIA method. The standard curves suggest that CMIA is a reliable and reproducible immunoassay procedure for phenobarbital.

High-pressure infrared and FT-Raman investigation of a dental composite.

Composite resins are often used as filling materials on load-bearing surfaces of teeth. As masticatory stresses can be high, here, we study the effect of pressure on the behaviour of a dental composite. Using a polymerized wafer, the IR and FT-Raman spectra of a zirconia-containing proprietary composite (Z100, 3M, Minneapolis, MN, USA) were recorded. The high-pressure IR spectra were also recorded. Band assignments were made for the main peaks of both organic and inorganic components. Breaks in the pressure dependences (dv/dP) of the organic components were found at 22 kbar. Different pressure dependences for different vibrational modes of inorganic components were also observed. These data suggest that the network structure of the composite is compacted under high pressure and that both the atomic distance and bonding angles in the network are altered.

Practical tethering of vitamin B1 on a silica surface via its phosphate group and evaluation of its activity.

A convenient immobilization of thiamine pyrophosphate molecules on a silica surface through the phosphate group is developed, leading to a very active heterogenized biocatalyst for pyruvate decarboxylation.

An FT-Raman spectroscopic investigation of dentin and collagen surfaces modified by 2-hydroxyethylmethacrylate.

Although 2-hydroxyethylmethacrylate (HEMA) is commonly used for adhesive bonding to dentin, its role in promoting adhesion is not completely understood. Here, we use FT-Raman spectroscopy to elucidate further the nature of the interaction of HEMA with dentin. Ground dentin was exposed to 2.5% (w/w) nitric acid, washed, dried in air, and treated with HEMA. The samples were then sequentially washed with distilled water, with FT-Raman spectra being obtained after different wash times. Hydroxyapatite and bovine type I collagen were similarly treated with HEMA except for the acid exposure. The FT-Raman spectra of these samples were also recorded. The spectra of HEMA-treated water-washed dentin and collagen revealed the following changes: (1) The band intensities of HEMA absorbed on dentin and collagen decreased with increasing wash times (2) the nu(C=O) and nu(CCO) modes of HEMA at 1718 and 607 cm-1, respectively, either disappeared or decreased after extensive washing; (3) the nu (C=C) (1640 cm-1) and delta (=CH2), (1403 cm-1) bands exhibited minor variations in band position and relative intensity. These results demonstrate that HEMA interacts with dentin both physically and chemically. The chemical interaction can be interpreted by either hydrogen bonding or the formation of a new bond to the ester group of HEMA.

Microperoxidase-11: molecular dynamics and Q-band excited resonance Raman of the oxidized, reduced and carbonyl forms.

Resonance Raman spectra with Q-band excitation are reported for microperoxidase-11, the cytochrome c analog. Spectra were acquired in the mid-frequency range for the oxidized, and reduced forms of the undecapeptide, as well as for the imidazole and carbonyl complexes. Oxidation and spin state marker bands of the undecapeptides are consistent with a six-coordinate, low spin iron in both oxidation states. Porphyrin core size correlations yield a porphyrin-centre to pyrrole-nitrogen distance of 2.00 A for MP11, suggestive of a six-coordinate species in a distorted heme environment. Molecular dynamics results show that the non-planarity of the heme of the parent cytochrome is conserved in the microperoxidase and its carbonmonoxy analog.

Synthesis of some 6 beta-acetylthio hydroxysteroids.

The reactions of 3 beta-hydroxy-20-oxo-5-pregnene-16 alpha-carbonitrile, 3 beta-hydroxy-5-androsten-17-one, 3 beta-hydroxy-5-pregnen-20-one, and 5-cholesten-3 beta-ol with thioacetic acid in dioxane afford mainly 6 beta-acetylthio derivatives which were characterized by IR, NMR (1H, 13C), and mass spectroscopy. A similar reaction of 17 beta-hydroxy-1,4-androstadien-3-one yields chiefly the known 1 alpha-SCOCH3 derivative.

A useful UV spectroscopic method for the determination of the concentration of diethylenetriamine (DETA) in aqueous mineral flotation solutions.

An alternative method for the determination of the concentration of diethylenetriamine (DETA) in aqueous mineral flotation solutions is described. This method is based on the formation of a DETA-Ni(II)-sulphite complex, which shows a UV absorption maximum at 285 nm that varies linearly with the concentration of DETA throughout the 0-50 mg l(-1) DETA range. A high concentration of Ni(II) is used to offset the effect of any Cu(II) or Ni(II) ions that may already be present in the industrial plant solutions under analysis. The intensity of the absorbance maximum is dependent on the sulphite ion concentration, but this problem is overcome by measuring the absorbances when the test solutions are spiked with different concentrations of DETA and then extrapolating the absorbance versus DETA concentration plot to zero absorbance to obtain the original concentration of DETA in the test solutions.

Pressure-tuning infrared and Raman spectroscopy of group 14 tetraphenyl compounds.

The effect of high external pressures on the vibrational spectra of the tetraphenyl Group 14 compounds, Ph4M (M = Si, Ge, Sn, Pb), were examined between ambient pressure and 40 kbar with the aid of a diamond-anvil cell. The four compounds displayed similar behaviour as the pressure was increased and a structural transition at approximately 15 kbar, most probably associated with a phenyl ring rotation, was identified in each case. The pressure dependencies of selected vibrational modes were obtained.

[Raman and infrared spectral studies of tungsten organometallic carbyne complex at high external pressure].

The Raman and infrared spectra of complex: [Cl(CO)2 (DPPE) W identical to CC6H4C identical to CC6H4NC]2 Re Cl(CO)3 (DPPE = bis (diphenylphosphino) ethane, (Ph)2PCH2CH2P(Ph)2) were measured at high external pressure (up to about 50 kbar). The pressure induced phase transition was observed near 30 kbar. The pressure dependence d nu/dp of nu (W identical to C) at the low-pressure phase is a little high (0.59 cm-1.(kbar)-1) and is very low (0.04 cm-1.(kbar)-1) at the high-pressure phase. It shows that the pi-backbonding from W to pi*--orbital of CO is strengthened at the high external pressure in fragment Cl(CO)2 (DPPE) W identical to C; The bond intensity and the force constant of W identical to C and nu (W identical to C) are decreasing; This effect compete with the normal increasing nu (W identical to C) on compression.

Synthesis, structural characterization and in vitro inhibitory studies against human breast cancer of the bis-(2,6-di-tert-butylphenol)tin(IV) dichloride and its complexes.

Four new organotin(IV) complexes of bis-(2,6-di-tert-butylphenol)tin(IV) dichloride [(tert-Bu-)(2)(HO-Ph)](2)SnCl(2) (1) with the heterocyclic thioamides 2-mercapto-pyrimidine (PMTH), 2-mercapto-4-methyl-pyrimidine (MPMTH), 2-mercapto-pyridine (PYTH) and 2-mercapto-benzothiazole (MBZTH), of formulae {[(tert-Bu-)(2)(HO-Ph)](2)Sn(PMT)(2)} (2), {[(tert-Bu-)(2)(HO-Ph)](2)Sn(MPMT)(2)} (3), {[(tert-Bu-)(2)(HO-Ph)](2)SnCl(PYT)} (4) and {[(tert-Bu-)(2)(HO-Ph)](2)SnCl(MBZT)} (5), have been synthesized and characterized by elemental analysis, (1)H-, (13)C-, (119)Sn-NMR, EPR, FT-IR, Raman and Mössbauer spectroscopic techniques. The crystal and molecular structures of compounds 1­5 have been determined by X-ray diffraction. The geometries around the metal center adopted in complexes 1­5 varied between tetrahedral in 1, trigonal bipyramidal in 3, 4, 5 and distorted octahedral in 2. Two carbon atoms from aryl groups and two chlorine atoms form a distorted tetrahedron in the case of 1. Two carbon, two sulfur and two nitrogen atoms from thione ligands form a distorted octahedral geometry around tin(IV) with trans-C(2), cis-N(2), cis-S(2)-configurations in 2. However, in the case of 4 and 5 complexes two carbon, one sulfur, one nitrogen and one chloride atom form a distorted trigonal bipyramidal arrangement. Finally, in the case of 3 the trigonal bipyramidal geometry is achieved by two carbon, two sulfur and one nitrogen atom in a unique coordination mode of thioamides toward the tin(IV) cation. Compounds 1­5 were tested for their in vitro cytotoxicity against the human breast adenocarcinoma (MCF-7) cell line. Compound 3 exhibits strong cytotoxic activity against MCF-7 cells (IC(50) = 0.58 ± 0.1 µM).

Synthesis of erbium hydroxide microflowers and nanostructures in subcritical water.

The effects of temperature, pressure, pH, residence time and reactant concentrations, as well as the presence or absence of CO(2), on the size and morphology of erbium hydroxide particles synthesized in a hydrothermal batch reactor and a diamond-anvil cell (DAC) reactor have been investigated. Several new erbium-based microstructures and nanostructures were obtained that encompass different phases and shapes, including crystalline microflowers, hexagonal microlayers, microsticks and microspheres made from nanoparticles, as well as nanofibers, nanorods and nanolayers. The Er(2)OCO(3)(OH)(2) microflowers are pure, structurally uniform, and mostly free from dislocations. Their crystallinity, morphology, optical properties and structural features have been examined and compared with those of the other phases by field-emission scanning electron microscopy (SEM), x-ray diffraction (XRD), and energy-dispersive x-ray (EDX) analysis, and by Raman, infrared, UV-visible and fluorescence spectroscopy.

Fourier transform infrared spectroscopic method for the quantitative trace analysis of transition-metal carbonyl-labeled bioligands.

A quantitative FT-IR spectroscopic method has been developed for the trace analysis in chlorinated organic solvents of transition-metal carbonyl-labeled bioligands. In order to illustrate the widespread analytical potential of the method, three derivatives of the female hormonal steroid 17 beta-estradiol, containing Cr(CO)3, Cp2Mo2(CO)4 (Cp = eta 5-C5H5), and Co2(CO)6 as labels, and the anticonvulsant drug phenobarbital, labeled with (eta 5-C5H4)Mn(CO)3, were examined. The cobalt carbonyl marker proved to be the best sulted for quantitative analysis purposes, and the minimum tracer quantity detectable for this particular marker (64 scans, 4-cm-1 resolution, 3.5 min) was optimized in CCl4 solution at about 300 fmol (or 0.3 pmol, 180 pg) by using an ultralow volume (23.0 microL), gold light-pipe IR solution cell and a liquid nitrogen cooled, InSb (indium antimonide) IR detector. The repeatability of this radically different analytical procedure over the concentration range 1.0 x 10(-6) to 5.0 x 10(-8) M was good (coefficient of variance less than or equal to 6%) and the method provides the basis for a new immunological test--carbonylmetalloimmunoassay (CMIA).

(N-succinimidyl 4-pentynoate)hexacarbonyldicobalt: a transition-metal carbonyl complex having similar uses to the Bolton-Hunter reagent.

The synthesis of the transition-metal carbonyl complex (N-succinimidyl 4-pentynoate)hexacarbonyldicobalt [[(C4H4O2N)O(CO)CH2CH2C identical to CH]Co2(CO)6] is described. This cobalt carbonyl complex is structurally similar to the Bolton-Hunter conjugation reagent and has been successfully employed as a nonradioactive tracer for labeling the drug carbamazepine. The metal carbonyl tracer can be detected at extremely low concentrations (ca. 1 pmol) by FT-IR spectroscopy in the v(CO) region (2150-1800 cm-1). The cobalt carbonyl labeled carbamazepine retains good recognition for anti-carbamazepine antibodies. This novel labeling procedure, which can be broadly termed carbonylmetalloimmunoassay (CMIA), has considerable potential for assaying a wide range of biological materials.

Organometallic estrogens: synthesis, interaction with lamb uterine estrogen receptor, and detection by infrared spectroscopy.

As an integral part of the development of a new technique using organometallic markers for the detection of hormone receptors by FT-IR spectroscopy, a series of estradiol derivatives labeled with Cr(CO)3 or Cr(CO)2CS fragments on the A ring has been synthesized. The stereochemistry of one of these steroids, alpha-[3-(dimethyl-tert-butylsiloxy)-17 beta-estradiol]dicarbonyl(thiocarbonyl)chromium(0), has been established by X-ray diffraction. The organochromium-labeled steroids are stable in aqueous methanol solution, and their relative binding affinities to estrogen receptor have been determined; these values vary from 0.4 to 28%. The complex exhibiting the strongest affinity, [3-O-(3-hydroxypropyl)-17 beta-estradiol]-chromium tricarbonyl complex, has been prepared in a tritiated form with a high specific activity (4.1 Ci/mmol). This tritiated hormone binds reversibly to the estradiol receptor in lamb uterine cytosol with an affinity (Kd = 0.85 nM) and number of binding sites (n = 770 fmol/mg of protein) close to the values observed for estradiol itself. The level of nonspecific binding is low, and the hormone is not bound significantly to other nontarget tissues. The observation that the binding affinity of the steroid depends on which side of the steroidal A ring the organometallic label is bound demonstrates the nonequivalence of the two sides of the A ring with respect to the receptor site. The FT-IR spectra of the organochromium markers in the v(CO) region can be used for the detection of the estradiol receptor in lamb uterine cytosol.

Effect of high external pressures on the vibrational spectra of biomedical materials: calcium hydroxyapatite and calcium fluoroapatite.

Infrared and Raman spectra of the principal mineral component of human hard tissue, calcium hydroxyapatite, Ca10(PO4)6(OH)2, or HAP, and the analogous calcium fluoroapatite, Ca10(PO4)6F2, or FAP, have been recorded, using a diamond-anvil cell, at pressures ranging from ambient to 30 kbar. For FAP, the absence of any discontinuities in the slopes of the nu (cm-1) versus P (kbar) plots for the observed bands indicates that no pressure-induced structural transition occurs in this material throughout the pressure range investigated. For the internal vibrational modes of HAP, however, there are distinct breaks at approximately 20 kbar in the nu versus P plots, suggesting the occurrence of a structural change at this pressure. The OH stretching mode of HAP shifts to higher wave numbers with increasing pressure while the associated OH librational mode shifts in the opposite direction. The pressure-induced structural transition in HAP is reversible and occurs at approximately 22 kbar upon decompression. Further evidence for a structural change taking place at approximately 20 kbar was provided by a parallel pressure-tuning Raman study. Hydrogen bonding does not occur, or is very weak, in HAP.