Adsorption and viscoelastic analysis of polyelectrolyte-surfactant complexes on charged hydrophilic surfaces.

The aggregation of surfactants around oppositely charged polyelectrolytes brings about a peculiar bulk phase behavior of the complex, known as coacervation, and can control the extent of adsorption of the polyelectrolyte at an aqueous-solid interface. Adsorption kinetics from turbid premixed polyelectrolyte-surfactant mixtures have been difficult to measure using optical techniques such as ellipsometry and reflectometry, thus limiting the correlation between bulk phases and interfacial adsorption. Here, we investigated the adsorption from premixed solutions of a cationic polysaccharide (PQ10) and the anionic surfactant sodium dodecyl sulfate (SDS) on an amphoteric alumina surface using quartz crystal microbalance with dissipation (QCMD). The surface charge on the alumina was tuned by changing the pH of the premixed solutions, allowing us to assess the role of electrostatic interactions by studying the adsorption on both negatively and positively charged surfaces. We observed a maximum extent of adsorption on both negatively and positively charged surfaces from a solution corresponding to the maximum turbidity. Enhanced adsorption upon diluting the redissolved complexes at a high SDS concentration was seen only on the negatively charged surface, and not on the positively charged one, confirming the importance of electrostatic interactions in controlling the adsorption on a hydrophilic charged surface. Using the Voight based viscoelastic model, QCMD also provided information on the effective viscosity, effective shear modulus, and thickness of the adsorbed polymeric complex. The findings of viscoelastic analysis, corroborated by atomic force microscopy measurements, suggest that PQ10 by itself forms a flat, uniform layer, rigidly attached to the surface. The PQ10-SDS complex shows a heterogeneous surface structure, where the underlayer is relatively compact and tightly attached and the top is a loosely bound diffused overlayer, accounting for most of the adsorbate, which gets washed away upon rinsing. Understanding of the surface structure will have important implications toward understanding lubrication.

Molecular Changes in Spider Viscid Glue As a Function of Relative Humidity Revealed Using Infrared Spectroscopy.

Spider aggregate glue can absorb moisture from the atmosphere to reduce its viscosity and become tacky. The viscosity at which glue adhesion is maximized is remarkably similar across spider species, even though that viscosity is achieved at very different relative humidity (RH) values matching their diverse habitats. However, the molecular changes in the protein structure and the bonding state of water (both referred to here as molecular structure) with respect to the changes in RH are not known. We use attenuated total reflectance-infrared (ATR-IR) spectroscopy to probe the changes in the molecular structure of glue as a function of RH for three spider species from different habitats. We find that the glue retains bound water at lower RH and absorbs liquid-like water at higher RH. The absorption of liquid-like water at high RH plasticizes the glue and explains the decrease in glue viscosity. The changes to protein conformations as a function RH are either subtle or not detectable by IR spectroscopy. Importantly, the molecular changes are reversible over multiple cycles of RH change. Further, separation of glue constituents results in a different humidity response as compared to pristine glue, supporting the standing hypothesis that the glue constituents have a synergistic association that makes spider glue a functional adhesive. The results presented in this study provide further insights into the mechanism of the humidity-responsive adhesion of spider glue.

Hygroscopic compounds in spider aggregate glue remove interfacial water to maintain adhesion in humid conditions.

Adhesion in humid environments is fundamentally challenging because of the presence of interfacial bound water. Spiders often hunt in wet habitats and overcome this challenge using sticky aggregate glue droplets whose adhesion is resistant to interfacial failure under humid conditions. The mechanism by which spider aggregate glue avoids interfacial failure in humid environments is still unknown. Here, we investigate the mechanism of aggregate glue adhesion by using interface-sensitive spectroscopy in conjunction with infrared spectroscopy. We demonstrate that glycoproteins act as primary binding agents at the interface. As humidity increases, we observe reversible changes in the interfacial secondary structure of glycoproteins. Surprisingly, we do not observe liquid-like water at the interface, even though liquid-like water increases inside the bulk with increasing humidity. We hypothesize that the hygroscopic compounds in aggregate glue sequester interfacial water. Using hygroscopic compounds to sequester interfacial water provides a novel design principle for developing water-resistant synthetic adhesives.

Effect of Acid-Base Interactions on Conformation of Adsorbed Polymer Chains.

Sum frequency generation spectroscopy (SFG) and attenuated-total-reflection IR (ATR-IR) were used to investigate polymer adsorption on solid surfaces in CCl4 (neutral), CHCl3 (acidic), and acetone (basic) solvents. Fowkes showed that the adsorbed amount of the polymer from acidic and basic solvents is less than that from a neutral solvent (Ind. Eng. Chem. Prod. Res. Dev. 1978, 17, 3-7). Here, we show that besides the differences in adsorbed amount, chains adsorbed from an acidic solvent adopted a flat conformation with a much smaller ratio of segments of loops and tails to trains compared to those adsorbed from a neutral solvent. Sapphire (Al2O3) surfaces were saturated by train segments at 1.3 × 10-5 volume fraction for both CCl4 and CHCl3 solutions, with a large fraction of the surface sites occupied by the PMMA segments, which was different from what was expected based on Fowkes' experiment. In contrast, PMMA segments were not able to replace acetone molecules from the surface in a time period of 2 h. Surface interaction parameters alone were unable to predict the differences in conformation of chains adsorbed from acidic or neutral solvents.

Ice-like water supports hydration forces and eases sliding friction.

The nature of interfacial water is critical in several natural processes, including the aggregation of lipids into the bilayer, protein folding, lubrication of synovial joints, and underwater gecko adhesion. The nanometer-thin water layer trapped between two surfaces has been identified to have properties that are very different from those of bulk water, but the molecular cause of such discrepancy is often undetermined. Using surface-sensitive sum frequency generation (SFG) spectroscopy, we discover a strongly coordinated water layer confined between two charged surfaces, formed by the adsorption of a cationic surfactant on the hydrophobic surfaces. By varying the adsorbed surfactant coverage and hence the surface charge density, we observe a progressively evolving water structure that minimizes the sliding friction only beyond the surfactant concentration needed for monolayer formation. At complete surfactant coverage, the strongly coordinated confined water results in hydration forces, sustains confinement and sliding pressures, and reduces dynamic friction. Observing SFG signals requires breakdown in centrosymmetry, and the SFG signal from two oppositely oriented surfactant monolayers cancels out due to symmetry. Surprisingly, we observe the SFG signal for the water confined between the two charged surfactant monolayers, suggesting that this interfacial water layer is noncentrosymmetric. The structure of molecules under confinement and its macroscopic manifestation on adhesion and friction have significance in many complicated interfacial processes prevalent in biology, chemistry, and engineering.