Nanoporous Gold: From Structure Evolution to Functional Properties in Catalysis and Electrochemistry.

Nanoporous gold (NPG) is characterized by a bicontinuous network of nanometer-sized metallic struts and interconnected pores formed spontaneously by oxidative dissolution of the less noble element from gold alloys. The resulting material exhibits decent catalytic activity for low-temperature, aerobic total as well as partial oxidation reactions, the oxidative coupling of methanol to methyl formate being the prototypical example. This review not only provides a critical discussion of ways to tune the morphology and composition of this material and its implication for catalysis and electrocatalysis, but will also exemplarily review the current mechanistic understanding of the partial oxidation of methanol using information from quantum chemical studies, model studies on single-crystal surfaces, gas phase catalysis, aerobic liquid phase oxidation, and electrocatalysis. In this respect, a particular focus will be on mechanistic aspects not well understood, yet. Apart from the mechanistic aspects of catalysis, best practice examples with respect to material preparation and characterization will be discussed. These can improve the reproducibility of the materials property such as the catalytic activity and selectivity as well as the scope of reactions being identified as the main challenges for a broader application of NPG in target-oriented organic synthesis.

A versatile heterogeneous photocatalyst: nanoporous gold powder modified with a zinc(II) phthalocyanine derivative for singlet oxygen [4 + 2] cycloadditions.

Nanoporous gold was functionalized with a photosensitizer, a zinc(II) phthalocyanine derivative. Such systems are active for the generation of reactive singlet oxygen which can be used for photocatalytic oxidation reactions. This study aims to demonstrate the versatility of such an approach, in terms of substrates and the employed solvent, only possible for a truly heterogeneous catalytic system. The activity of the hybrid system was studied for [4 + 2] cycloadditions of three different types of dienes and a total of eight substrates in two organic solvents and once in water. The highest activity was measured for 1,3-diphenylisobenzofuran, which is also highest in terms of sensitivity for the reaction with 1O2. Trends in conversion could be anticipated based on reported values for the rate constant for the reaction of 1O2. In almost all cases, an amplification of the conversion by immobilization of the sensitizer onto nanoporous gold was observed. The limiting case was ergosterol, which was the largest of all substrates with a van-der-Waals radius of about 2.1 nm. Additional factors such as the limited lifetime of 1O2 in different solvents as well as the hampered diffusion of the substrates were identified.

A versatile nanoreactor for complementary in situ X-ray and electron microscopy studies in catalysis and materials science.

Two in situ `nanoreactors' for high-resolution imaging of catalysts have been designed and applied at the hard X-ray nanoprobe endstation at beamline P06 of the PETRA III synchrotron radiation source. The reactors house samples supported on commercial MEMS chips, and were applied for complementary hard X-ray ptychography (23 nm spatial resolution) and transmission electron microscopy, with additional X-ray fluorescence measurements. The reactors allow pressures of 100 kPa and temperatures of up to 1573 K, offering a wide range of conditions relevant for catalysis. Ptychographic tomography was demonstrated at limited tilting angles of at least ±35° within the reactors and ±65° on the naked sample holders. Two case studies were selected to demonstrate the functionality of the reactors: (i) annealing of hierarchical nanoporous gold up to 923 K under inert He environment and (ii) acquisition of a ptychographic projection series at ±35° of a hierarchically structured macroporous zeolite sample under ambient conditions. The reactors are shown to be a flexible and modular platform for in situ studies in catalysis and materials science which may be adapted for a range of sample and experiment types, opening new characterization pathways in correlative multimodal in situ analysis of functional materials at work. The cells will presently be made available for all interested users of beamline P06 at PETRA III.

Nanoporous gold functionalized with praseodymia-titania mixed oxides as a stable catalyst for the water-gas shift reaction.

Dealloyed nanoporous metals hold great promise in the field of heterogeneous catalysis; however their tendency to coarsen at elevated temperatures or under catalytic reaction conditions sometimes limit further applications. Here, we report on a highly stable nanoporous gold catalyst (npAu) functionalized with praseodymia-titania mixed oxides as synthesized by a sol-gel method. Specifically, we used aberration-corrected transmission electron microscopy to study the morphology and the interface between the oxide deposits and the npAu substrate at the atomic level. Based on electron energy loss spectroscopy (EELS), it is concluded that Pr-TiOx mixed oxides form a solid solution. Flow reactor tests reveal that the Pr-TiOx functionalized nanoporous gold is not only highly active but also very stable for the water gas shift reaction in a large temperature range (180-400 °C). Our results demonstrate the potential of engineering the compositions of oxides coatings on npAu for advanced functional systems.

In Situ Ptychography of Heterogeneous Catalysts using Hard X-Rays: High Resolution Imaging at Ambient Pressure and Elevated Temperature.

A new closed cell is presented for in situ X-ray ptychography which allows studies under gas flow and at elevated temperature. In order to gain complementary information by transmission and scanning electron microscopy, the cell makes use of a Protochips E-chipTM which contains a small, thin electron transparent window and allows heating. Two gold-based systems, 50 nm gold particles and nanoporous gold as a relevant catalyst sample, were used for studying the feasibility of the cell. Measurements showing a resolution around 40 nm have been achieved under a flow of synthetic air and during heating up to temperatures of 933 K. An elevated temperature exhibited little influence on image quality and resolution. With this study, the potential of in situ hard X-ray ptychography for investigating annealing processes of real catalyst samples is demonstrated. Furthermore, the possibility to use the same sample holder for ex situ electron microscopy before and after the in situ study underlines the unique possibilities available with this combination of electron microscopy and X-ray microscopy on the same sample.

Catalysis by unsupported skeletal gold catalysts.

Catalysis is one of the key technologies for the 21st century for achieving the required sustainability of chemical processes. Critical improvements are based on the development of new catalysts and catalytic concepts. In this context, gold holds great promise because it is more active and selective than other precious metal catalysts at low temperatures. However, gold becomes only chemically and catalytically active when it is nanostructured. Since the 1970s and 1980s, the first type of gold catalysts that chemists studied were small nanoparticles on oxidic supports. With the later onset of nanotechnology, a variety of nanostructured materials not requiring a support or organic stabilizers became available within about the last 10 years. Among these are gold nanofoams generated by combustion of gold compounds, nanotube membranes prepared by electroless deposition of gold inside a template, and corrosion-derived nanoporous gold. Even though these materials are macroscopic in their geometric dimensions (e.g., disks, cubes, and membranes with dimensions of millimeters), they are comprised of gold nanostructures, for example, in the form of ligaments as small as 15 nm in diameter (nanoporous gold, npAu). The nanostructure brings about a high surface to volume ratio and a large fraction of low coordinated surface atoms. In this Account, we discuss how unsupported materials are active catalysts for aerobic oxidation reaction in gas phase (oxidation of CO and primary alcohols), as well as liquid phase oxidation and reduction reactions. It turns out that the bonding and activation of molecular oxygen for gas phase oxidations strongly profits from trace amounts of an ad-metal residue such as silver. It is noteworthy that these catalysts still exhibit the special gold type chemistry, characterized by activity at very low temperatures and high selectivity for partial oxidations. For example, we can oxidize CO over these unsupported catalysts (npAu, nanotubes, and powder) at temperatures well below water's freezing point (-30 °C) and with turnover frequencies up to 0.5 s(-1) (at 30 °C). Yet, we can anticipate the surface chemistry of these unsupported and extended gold surfaces based on model experiments under UHV conditions. We have demonstrated this for the selective oxidation of primary alcohols at low temperatures employing npAu catalysts. Chemists have paid growing interest to oxidation and reduction reactions in liquid phase catalysis, most suitable for synthetic organic chemistry. Early work on the aerobic oxidation of d-glucose in 2008 using Raney type npAu already showed the potential of this type of catalyst for liquid phase reactions. Since then, researchers have investigated further oxidation reactions (silanes to silanols) and reduction reactions of alkynes, as well as C-C coupling reactions ([4 + 2] benzannulation) and azo compound decomposition, with likely several more reactions to be reported in the next years. The advantage of this unsupported skeletal type of catalyst is its recyclability and retrievability without leaching of gold into the reaction medium, owing to its monolithic structure. Even though these materials contain nanoscopic structures, they are macroscopic in their geometric dimensions and pose no threat to the environment or health as discussed for other nanomaterials.

ALD functionalized nanoporous gold: thermal stability, mechanical properties, and catalytic activity.

Nanoporous metals have many technologically promising applications, but their tendency to coarsen limits their long-term stability and excludes high temperature applications. Here, we demonstrate that atomic layer deposition (ALD) can be used to stabilize and functionalize nanoporous metals. Specifically, we studied the effect of nanometer-thick alumina and titania ALD films on thermal stability, mechanical properties, and catalytic activity of nanoporous gold (np-Au). Our results demonstrate that even only 1 nm thick oxide films can stabilize the nanoscale morphology of np-Au up to 1,000°C, while simultaneously making the material stronger and stiffer. The catalytic activity of np-Au can be drastically increased by TiO(2) ALD coatings. Our results open the door to high-temperature sensor, actuator, and catalysis applications and functionalized electrodes for energy storage and harvesting applications.

Nanoporous Gold Catalyst for the Oxidative N-Dealkylation of Drug Molecules: A Method for Synthesis of N-Dealkylated Metabolites.

A novel method for the selective catalytic N-dealkylation of drug molecules on a nanoporous gold (NPG) catalyst producing valuable N-dealkylated metabolites and intermediates is described. Drug metabolites are important chemical entities at every stage of drug discovery and development, from exploratory discovery to clinical development, providing the safety profiles and the ADME (adsorption, distribution, metabolism, and elimination) of new drug candidates. Synthesis was carried out in aqueous solution at 80 °C using air (oxygen source) as oxidant, in single step with good isolated yields. Different examples examined in this study showed that aerobic catalytic N-dealkylation of drug molecules on NPG has a broad scope supporting N-deethylation, N-deisopropylation and N-demethylation, converting either 3° amines to 2° amines, or 2° amines to 1° amines.

Silver residues as a possible key to a remarkable oxidative catalytic activity of nanoporous gold.

Recently, several forms of unsupported gold were shown to display a remarkable activity to catalyze oxidation reactions. Experimental evidence points to the crucial role of residual silver present in very small concentrations in these novel catalysts. We focus on the catalytic properties of nanoporous gold (np-Au) foams probed via CO and oxygen adsorption/co-adsorption. Experimental results are analyzed using theoretical models represented by the flat Au(111) and the kinked Au(321) slabs with Ag impurities. We show that Ag atoms incorporated into gold surfaces can facilitate the adsorption and dissociation of molecular oxygen on them. CO adsorbed on top of 6-fold coordinated Au atoms can in turn be stabilized by co-adsorbed atomic oxygen by up to 0.2 eV with respect to the clean unsubstituted gold surface. Our experiments suggest a linking of that most strongly bound CO adsorption state to the catalytic activity of np-Au. Thus, our results shed light on the role of silver admixtures in the striking catalytic activity of unsupported gold nanostructures.

Comparison of the photocatalytic activity of novel hybrid photocatalysts based on phthalocyanines, subphthalocyanines and porphyrins immobilized onto nanoporous gold.

A series of different singlet oxygen photosensitizers was immobilized onto nanoporous gold powder with a mean pore size of 40 nm via copper catalyzed azide-alkyne cycloaddition. The attachment of phthalocyanine and porphyrin derivatives was performed on the peripheral substituent of the macrocycle, whereas the subphthalocyanine derivatives were attached via the axial substituent with respect to the macrocyclic ring system. All obtained hybrid systems were studied in the photooxidation of 2,5-diphenylfuran as a chemical singlet oxygen quencher and showed increased photocatalytic activity compared to the same amount of the corresponding photosensitizer in solution due to photoinduced interactions of the plasmon resonance of the nanostructured gold support and the attached photosensitizer. The understanding of the different photophysical interactions depending on the coordination mode of the macrocycle as well as the position of the absorbance in the electromagnetic spectrum is an important point in the development towards highly active hybrid photocatalysts covering a broad absorption range within the spectrum of visible light.

Effect of surface chemistry on the stability of gold nanostructures.

Understanding the role of surface chemistry in the stability of nanostructured noble-metal materials is important for many technological applications but experimentally difficult to access and thus little understood. To develop a fundamental understanding of the effect of surface chemistry on both the formation and stabilization of self-organized gold nanostructures, we performed a series of controlled-environment annealing experiments on nanoporous gold (np-Au) and ion-bombarded Au(111) single-crystal surfaces. The annealing experiments on np-Au in ambient ozone were carried out to study the effect of adsorbed oxygen under dynamic conditions, whereas the ion-bombarded Au single-crystal surfaces were used as a model system to obtain atomic-scale information. Our results show that adsorbed oxygen stabilizes nanoscale gold structures at low temperatures whereas oxygen-induced mobilization of Au surface atoms seems to accelerate the coarsening under dynamic equilibrium conditions at higher temperatures.

Nanoporous gold: a new material for catalytic and sensor applications.

Nanostructured materials are governed by their surface chemical properties. This is strikingly reflected by np-Au. This material can be generated by corrosion of bulk Ag-Au alloys. Based on a self-organisation process, a 3 dimensional sponge like gold structure evolves with ligaments in the range of only a few tens of nanometers. Due to its continuous porosity, the material can be penetrated by gases which then adsorb and interact with the surface. In this perspective we will review potential applications of np-Au resulting from this effect, namely heterogeneous gas phase catalysis, surface chemistry driven actuation, and adsorbate controlled stability of the nanostructure. We will summarize the current knowledge about the low temperature oxidation of CO as well as the highly selective oxidation of methanol. Furthermore, we will address the question how surface chemistry can influence the material properties itself. In particular, we will deal with (a) the actuation of np-Au by the reversible oxidation of its surface using ozone and (b) the adsorbate controlled coarsening of ligaments, using annealing experiments under ozone or inert gas atmosphere.

Impact of photosensitizer orientation on the distance dependent photocatalytic activity in zinc phthalocyanine-nanoporous gold hybrid systems.

Nanoporous gold powder was functionalized in a two-step approach by an azide terminated alkanethiol self-assembled monolayer (SAM) and a zinc(ii) phthalocyanine (ZnPc) derivative by copper catalyzed azide-alkyne cycloaddition (CuAAC). A series of different hybrid systems with systematic variation of the alkyl chain length on both positions, the alkanethiol SAM and the peripheral substituents of the ZnPc derivative, was prepared and studied in the photooxidation of diphenylisobenzofuran (DPBF). An enhancement by nearly one order of magnitude was observed for the photosensitized singlet oxygen (1O2) generation of the hybrid systems compared to the same amount of ZnPc in solution caused by the interaction of the npAu surface plasmon resonance and the excited state of the immobilized sensitizer. This interaction was shown to be distance dependent, with decreasing activity for short SAMs with alkyl chain lengths < 6 methylene groups caused by quenching of the excited state via electron transfer as well as decreasing activity for SAMs with n > 8 methylene groups due to decreasing energy transfer for long distances. An unexpected distance dependent behaviour was observed for the variation of the peripheral alkyl chain on the photosensitizer revealing a planar orientation of the immobilized photosensitizer on the nanoporous gold surface by a penta-coordinated central zinc ion through interaction with free azide groups from the self-assembled monolayer.

Photocatalytic coatings based on a zinc(ii) phthalocyanine derivative immobilized on nanoporous gold leafs with various pore sizes.

A series of singlet oxygen sensitizing hybrid materials is reported consisting of a zinc(ii) phthalocyanine (ZnPc) derivative immobilized on nanoporous gold leafs (npAu) with various pore sizes. The resulting photocatalytic coatings exhibit a thickness of around 100 nm and pore sizes between 9-50 nm. Herein, we report the synthesis and characterization of those hybrid materials which were synthesized by functionalization of npAu leafs by an azide terminated alkanethiol self-assembled monolayer (SAM) and subsequent copper catalyzed azide-alkyne cycloaddition (CuAAC). The characterization of the samples morphology included scanning electron microscopy (SEM), UV-Vis spectroscopy as well as energy dispersive X-ray spectroscopy (EDX). The morphology-reactivity relationship was investigated employing the hybrid photocatalysts in the photooxidation of diphenylisobenzofuran (DPBF) as selective singlet oxygen quencher. An increasing photocatalytic activity was found for smaller pore sizes up to 15 nm, due to the gain in specific surface area concomitant with an increasing amount of immobilized photosensitizer, completely dominating the effect of the higher spectral overlap caused by the shift of the plasmon resonance of npAu, until mass transport and diffusion limitation gets predominant for pore sizes below 15 nm.

Influence of distortions of recorded diffraction patterns on strain analysis by nano-beam electron diffraction.

Images acquired in transmission electron microscopes can be distorted for various reasons such as e.g. aberrations of the lenses of the imaging system or inaccuracies of the image recording system. This results in inaccuracies of measures obtained from the distorted images. Here we report on measurement and correction of elliptical distortions of diffraction patterns. The effect of this correction on the measurement of crystal lattice strain is investigated. We show that the effect of the distortions is smaller than the precision of the measurement in cases where the strain is obtained from shifts of diffracted discs with respect to their positions in images acquired in an unstrained reference area of the sample. This can be explained by the fact that diffraction patterns acquired in the strain free reference area of the sample are distorted in the same manner as the diffraction patterns acquired in the strained region of interest. In contrast, for samples without a strain free reference region such as nanoparticles or nanoporous structures, where we evaluate ratios of lattice plane distances along different directions, the distortions are usually not negligible. Furthermore, two techniques for the detection of diffraction disc positions are compared showing that for samples in which the crystal orientation changes over the investigated area it is more precise to detect the positions of many diffraction discs simultaneously instead of detecting each disc position independently.

Independent control over residual silver content of nanoporous gold by galvanodynamically controlled dealloying.

A new procedure was developed and characterized for the galvanodynamically controlled dealloying (GCD) of AuxAg100-x alloys to obtain nanoporous gold (npAu) mainly as an unsupported catalyst material for partial oxidation of alcohols. Such catalysts require residual Ag content of less than 1 at%. GCD was compared to the preparation of npAu by potentiostatically controlled deallyoing (PCD) and free corrosion (FC). The main advantage of GCD is the ability to obtain npAu with a predetermined residual Ag content including residual Ag contents below 1 at% while retarding the coarsening of the ligaments. For PCD and FC, there is a strong increase of ligament size with decreasing residual Ag content because the longer times required for dealloying unavoidably lead to coarsening of the npAu structure. On the other hand, GCD also prevented too high initial current density that leads to cracking of the samples and prevents formation of mechanically stable monoliths. GCD tolerates different compositions of the starting alloy for AuxAg100-x within the tested composition range (20 at% ≤ xAu ≤ 30 at%). The samples obtained by GCD were tested for methanol and ethanol oxidation and showed favorable characteristics for partial oxidation of methanol to methyl formate and of ethanol to ethyl acetate.

Correlative Multiscale 3D Imaging of a Hierarchical Nanoporous Gold Catalyst by Electron, Ion and X-ray Nanotomography.

Tomographic imaging of catalysts allows non-invasive investigation of structural features and chemical properties by combining large fields of view, high spatial resolution, and the ability to probe multiple length scales. Three complementary nanotomography techniques, (i) electron tomography, (ii) focused ion beam-scanning electron microscopy, and (iii) synchrotron ptychographic X-ray computed tomography, were applied to render the 3D structure of monolithic nanoporous gold doped with ceria, a catalytically active material with hierarchical porosity on the nm and µm scale. The resulting tomograms were used to directly measure volume fraction, surface area and pore size distribution, together with 3D pore network mapping. Each technique is critically assessed in terms of approximate spatial resolution, field of view, sample preparation and data processing requirements. Ptychographic X-ray computed tomography produced 3D electron density maps with isotropic spatial resolution of 23 nm, the highest so far demonstrated for a catalyst material, and is highlighted as an emerging method with excellent potential in the field of catalysis.

Potential-induced electronic structure changes in supercapacitor electrodes observed by in operando soft X-ray spectroscopy.

The dynamic physiochemical response of a functioning graphene-based aerogel supercapacitor is monitored in operando by soft X-ray spectroscopy and interpreted through ab initio atomistic simulations. Unanticipated changes in the electronic structure of the electrode as a function of applied voltage bias indicate structural modifications across multiple length scales via independent pseudocapacitive and electric double layer charge storage channels.

Nanoporous gold: a new gold catalyst with tunable properties.

Nanoporous gold (np-Au) represents a novel nanostructured bulk material with very interesting perspectives in heterogeneous catalysis. Its monolithic porous structure and the absence of a support or other stabilizing agents opens up unprecedented possibilities to tune structure and surface chemistry in order to adapt the material to specific catalytic applications. We investigated three of these tuning options in more detail: change of the porosity by annealing, increase of activity by the deposition of oxides and change of activity and selectivity by bimetallic effects. As an example for the latter case, the effect of Ag impurities will be discussed. The presence and concentration of Ag can be correlated to the availability of active oxygen. While for the oxidation of CO the activity of the catalyst can be significantly enhanced when increasing the content of Ag, we show for the oxidation of methanol that the selectivity is shifted from partial to total oxidation. In a second set of experiments, two different metal-oxides were deposited on np-Au, praseodymia and titania. In both cases, the surface chemistry changed significantly. The activity of the catalyst for oxidation of CO was increased by up to one order of magnitude after modification. Finally, we used adsorbate controlled coarsening to tune the structure of np-Au. In this way, even gradients in the pore- and ligament size could be induced, taking advantage of mass transport phenomena.