RESUMO
The success of obtaining solid dispersions for solubility improvement invariably depends on the miscibility of the drug and polymeric carriers. This study aimed to categorize and select polymeric carriers via the classical group contribution method using the multivariate analysis of the calculated solubility parameter of RX-HCl. The total, partial, and derivate parameters for RX-HCl were calculated. The data were compared with the results of excipients (N = 36), and a hierarchical clustering analysis was further performed. Solid dispersions of selected polymers in different drug loads were produced using solvent casting and characterized via X-ray diffraction, infrared spectroscopy and scanning electron microscopy. RX-HCl presented a Hansen solubility parameter (HSP) of 23.52 MPa1/2. The exploratory analysis of HSP and relative energy difference (RED) elicited a classification for miscible (n = 11), partially miscible (n = 15), and immiscible (n = 10) combinations. The experimental validation followed by a principal component regression exhibited a significant correlation between the crystallinity reduction and calculated parameters, whereas the spectroscopic evaluation highlighted the hydrogen-bonding contribution towards amorphization. The systematic approach presented a high discrimination ability, contributing to optimal excipient selection for the obtention of solid solutions of RX-HCl.
Assuntos
Química Farmacêutica , Excipientes , Polímeros , Cloridrato de Raloxifeno , Solubilidade , Difração de Raios X , Polímeros/química , Excipientes/química , Cloridrato de Raloxifeno/química , Análise Multivariada , Difração de Raios X/métodos , Química Farmacêutica/métodos , Portadores de Fármacos/química , Composição de Medicamentos/métodos , Microscopia Eletrônica de Varredura/métodos , Ligação de Hidrogênio , Cristalização/métodosRESUMO
This work aimed to develop a three-dimensional (3D) wearable drug-loaded earring tap to treat affections caused by aesthetic perforations. The initial phase involved a combination of polymers to prepare filaments for fused deposition modeling (FDM) 3D printing using a centroid mixture design. Optimized filament compositions were used in the second phase to produce 3D printed earring taps containing the anti-inflammatory naringenin. Next, samples were assessed via physicochemical assays followed by in vitro skin permeation studies with porcine ear skin. Two filament compositions were selected for the study's second phase: one to accelerate drug release and another with slow drug dissolution. Both filaments demonstrated chemical compatibility and amorphous behavior. The use of the polymer blend to enhance printability has been confirmed by rheological analysis. The 3D devices facilitated naringenin skin penetration, improving drug recovery from the skin's most superficial layer (3D device A) or inner layers (3D device B). Furthermore, the devices significantly decreased transdermal drug delivery compared to the control containing the free drug. Thus, the resulting systems are promising for producing 3D printed earring taps with topical drug delivery and reinforcing the feasibility of patient-centered drug administration through wearable devices.
RESUMO
Transdermal administration of raloxifene hydrochloride (RLX)-loaded nanostructured lipid carriers (NLCs) has been proposed to circumvent its low oral bioavailability (2%). Preformulation studies were carried out to evaluate drug-excipient compatibility of various adjuvants commonly used for NLC preparation (waxes, cholesterol, compritol, gelucire, span 60, span 80, span 85, tween 80, poloxamer 188, oleic acid, caprylic/capric triglyceride, and castor oil). It was used differential scanning calorimetry (DSC), isothermal stress testing (IST), and solubility studies. The most promising excipients were chosen for NLC obtention, and full characterization was done, including in vitro skin permeation. DSC curves suggested drug-excipient interaction among some compounds, and the IST study showed incompatibility of RLX with waxes, compritol, cholesterol, span 60, and poloxamer 188. Solubility studies helped select gelucire, caprylic/capric triglyceride, span 80, and tween 80 for NLC production. Twelve NLCs were obtained (NLC1 to NLC12), but NLC7 and NLC8 were the most promising ones. In vitro release studies demonstrated that NLC7 and NLC8 were able to control RLX release (14.74 and 9.07% at 24 h, respectively) compared with the unloaded drug (> 90% at 24 h). Unloaded RLX did not permeate the diffusion cells' receptor medium and showed higher drug skin retention (11-fold) than RLX-loaded NLC. NLC reduced RLX skin retention, favoring drug permeation to deeper skin layers. NLC7 increased drug flux is 2.4-fold. NLC7 is a promising formulation for RLX transdermal drug delivery.
Assuntos
Nanopartículas , Nanoestruturas , Administração Cutânea , Portadores de Fármacos/química , Excipientes/química , Lipossomos , Nanopartículas/química , Tamanho da Partícula , Poloxâmero , Polissorbatos , Cloridrato de Raloxifeno , Triglicerídeos , CerasRESUMO
Entomopathogenic fungi can achieve important innovative outcomes for integrated mosquito control especially of Aedes aegypti, the key vector of arboviruses to humans in the tropics and subtropics. This study sought to design and to develop a simple dissemination device to attract and to infect gravid A. aegypti adults with a granular formulation of the ascomycete Metarhizium humberi IP 46, and to validate this device in the laboratory as well as in semi-field and field conditions. Hydrogel (polyacrylamide potassium polyacrylate) was confirmed to be a suitable substitute for water used in the device that attracted gravid females under field conditions. Females laid eggs on black polyethylene terephthalate carpet fixed in the device that also proved to be a suitable substrate for a granular formulation of fungal microsclerotia and/or conidia. The plastic device (29.5 cm high) was divided into a lower closed compartment with a water reservoir and an upper, laterally open but covered compartment with continuously hydrated gel and the fungal formulation attached to the carpet. The uppermost compartment permitted free circulation of mosquito adults. The device attracted both male and female A. aegypti. The fungal formulations of IP 46 propagules tested in the device were effective against adults in laboratory, semi-field, and field settings. Findings in the laboratory, semi-field, and especially in field conditions strengthen the value and utility of this innovative device for focal applications of a mycoinsecticide against this important mosquito vector.Key points⢠Low-cost and simple disseminating device for focal control of Aedes aegypti.⢠Granulized Metarhizium humberi IP 46 and hydrogel yield extended control.⢠Findings in field tests strengthen benefit of the device for focal application.
Assuntos
Aedes , Metarhizium , Animais , Brasil , Feminino , Humanos , Masculino , Mosquitos VetoresRESUMO
Skin ulcers, wounds, or burns represent a burden for health care worldwide. Our aim was to explore the effects of mucoadhesive formulation with Curcuma longa L. extract mucoadhesive formulation containing curcumin (MFC) on skin healing in Wistar rats. Fifty-four rats were randomly allocated into 3 groups: control, vehicle, and MFC. A full-thickness circular wound was induced on the back of each animal. Two daily applications of the products were performed according to the experimental group. On days 3, 10, and 21, 6 animals in each group were euthanized. Clinical analysis was based on wound area. Histologic analysis was performed in hematoxylin and eosin-stained sections, with re-epithelization and inflammation being assessed by means of semiquantitative scores. To analyze the Akt/mTOR pathway, immunohistochemistry for phospho Akt (pAkt) and phospho ribosomal protein S6 were investigated. In addition, nuclear factor kappa-light-chain-enhancer of activated B cells immunolabeling was performed. Clinical analysis revealed wounds with a smaller area on days 3 and 10 in curcumin-treated animals. Histologically, MFC had a significant impact on inflammatory events on days 3 and 10 and promoted faster re-epithelization, which was evidenced on day 10. MFC-treated wounds exhibited pAkt upregulation on day 10 and both pAkt and phospho ribosomal protein S6 downregulation on day 21. Nuclear factor kappa-light-chain-enhancer of activated B cells expression varied through the evaluation periods; however, no significant difference was observed between groups. Collectively, our results indicate that MFC is efficient in accelerating cutaneous wound repair through modulation of the inflammatory process and stimulus of re-epithelization by an Akt/mTOR-dependent mechanism.
Assuntos
Curcuma/química , Regulação da Expressão Gênica/efeitos dos fármacos , NF-kappa B/biossíntese , Extratos Vegetais/farmacologia , Cicatrização/efeitos dos fármacos , Animais , Imuno-Histoquímica , Masculino , Extratos Vegetais/química , Proteínas Proto-Oncogênicas c-akt/metabolismo , Ratos , Ratos WistarRESUMO
Granular microsclerotial formulations of entomopathogenic fungi deserve attention because of their post-application, in situ production of new conidia that enhance and prolong mycoinsecticidal efficacy against a target pest insect. Because high ambient moisture is a crucial condition to induce fungal development and conidiogenesis on granules, we tested the impacts of the additions of three humectants-glycerin, propylene glycol, and polyethylene glycol 400-on water absorption by pellets incorporating microsclerotia of Metarhizium humberi IP 46 with microcrystalline cellulose or vermiculite carriers, and on the production of infective conidia of IP 46 microsclerotia in ambient humidities suboptimal for routine conidiogenesis. Glycerin facilitated greater and faster absorption of water than the other humectants. Microcrystalline cellulose absorbed low quantities of water without any added humectant whereas vermiculite did not. IP 46 did not grow or sporulate on pellets prepared with or without glycerin at 86% relative humidity (RH) or on control pellets without glycerin at 91% RH; conidial production on pellets prepared with vermiculite or microcrystalline cellulose and 10% glycerin reached 1.1 × 105 conidia/mg and 1 × 105 conidia/mg, respectively, after 20 days of exposure at 91% RH. Hence, these results strongly support glycerin as a suitable humectant for granular microsclerotial formulations of this fungus.
Assuntos
Higroscópicos/farmacologia , Metarhizium/efeitos dos fármacos , Metarhizium/fisiologia , Esporos Fúngicos/efeitos dos fármacos , Esporos Fúngicos/crescimento & desenvolvimento , Glicerol/farmacologia , Higroscópicos/classificação , Controle Biológico de Vetores , Propilenoglicol/farmacologia , Água/metabolismoRESUMO
This work aimed to select an effective penetration enhancer (PE) for nail pretreatment, develop voriconazole (VOR)-loaded nanomicelles, and evaluate their ability to deliver VOR to the nail. A complete analysis of nail protein dynamics, bond rupture, and microstructure was performed. Alternative methods as electron paramagnetic resonance (EPR) and the Ellman's reagent (DTNB) assay were also evaluated. Nanomicelles were produced and characterized. The PE hydrated the hooves, following the order: urea ≈ cysteine ≈ glycolic acid < thioglycolic acid (TGA) < NaOH. SEM images and methylene blue assay showed enlarged pores and roughness of porcine hooves after incubation with NaOH and TGA. EPR was demonstrated to be the most sensitive technique. DTNB assay quantified higher thiol groups for samples treated with TGA (p < 0.05). A stratigraphic analysis with Raman spectroscopy demonstrated that hooves treated with TGA presented a higher SH/SS ratio at the edges, affecting protein secondary structure. In vitro permeation studies demonstrated significant VOR permeation (29.44 ± 6.13 µg/cm2), 10-fold higher than previous studies with lipid nanoparticles. After TGA pretreatment, VOR permeation was further enhanced (3-fold). TGA pretreatment followed by VOR-loaded nanomicelles demonstrates a promising approach for onychomycosis treatment. The novel methods for protein analysis were straightforward and helpful.
Assuntos
Unhas , Onicomicose , Animais , Dissulfetos , Onicomicose/tratamento farmacológico , Suínos , Tioglicolatos , VoriconazolRESUMO
BACKGROUND: Although a highly common practice in hospital care, tablet splitting can cause dose variation and reduce drug stability, both of which impair drug therapy. OBJECTIVE: To determine the overall prevalence of tablet splitting in hospital care as evidence supporting the rational prescription of split tablets in hospitals. METHODS: Data collected from inpatients' prescriptions were analyzed using descriptive statistics and used to calculate the overall prevalence of tablet splitting and the percentage of split tablets that had at least one lower-strength tablet available on the market. The associations between the overall prevalence and gender, age, and hospital unit of patients were also assessed. The results of laboratory tests, performed with a commercial splitter, allowed the calculation of the mass loss, mass variation, and friability of the split tablets. RESULTS: The overall prevalence of tablet splitting was 4.5%, and 78.5% of tablets prescribed to be split had at least one lower-strength tablet on the market. The prevalence of tablet splitting was significantly associated with the patient's age and hospital unit. Laboratory tests revealed mean values of mass loss and variation of 8.7% (SD 1.8) and 11.7% (SD 2.3), respectively, both of which were significantly affected by the presence of coating and scoreline. Data from laboratory tests indicated that the quality of 12 of the 14 tablets deviated in at least one parameter examined. CONCLUSIONS: The high percentage of unnecessary tablet splitting suggests that more regular, rational updates of the hospital's list of standard medicines are needed. Also, inappropriate splitting behavior suggests the need to develop tablets with functional scores.
RESUMO
This study aimed to investigate whether hot-melt extrusion (HME) processing can modify the interactions between drugs, cyclodextrins and polymers, and in turn alter the microstructure and properties of supramolecular gels. Mixtures composed of amphiphilic polymer (Soluplus), cyclodextrin (HPßCD or αCD), plasticizer (PEG400 or PEG6000) and colloidal silicon dioxide were processed by HME. Carvedilol (CAR) was added to the formulation aiming its transdermal delivery. Extrudates were characterized by HPLC, XRPD, FTIR, DSC, and solid-state NMR. Gels prepared from extrudates (HME gels) or the corresponding physical mixtures (PM gels) in PBS were analyzed regarding components ordering (NMR, SEM), rheology, and CAR diffusion rate. HME led to the loss of the crystalline lattice of CAR and αCD, without causing any drug degradation. Solid NMR indicated that HME promoted the interaction of α-CD and HPßCD with the other components. HME gels had no coarsely disperse particles in their structure and behaved as weak gels (G' ~ Gâ³). In contrast, PM gels contained drug crystals and showed elastic behavior (G' > Gâ³). In general, HME gels were less viscous than PM ones and led to higher drug flux, especially those prepared using HPßCD. Moreover, the association of HPßCD and PEG6000 provided faster drug flux from supramolecular gels regardless the higher gel viscosity. The results evidenced that HME processing can decisively modify the arrangement of the components in the supramolecuar gels and, consequently, their properties, notably increasing drug release rate.
Assuntos
2-Hidroxipropil-beta-Ciclodextrina/química , Carvedilol/administração & dosagem , Excipientes/química , Rotaxanos/química , Administração Cutânea , Antagonistas Adrenérgicos beta/administração & dosagem , Antagonistas Adrenérgicos beta/química , Carvedilol/química , Química Farmacêutica , Liberação Controlada de Fármacos , Géis , Plastificantes/química , Polietilenoglicóis/química , Polímeros/química , Reologia , Viscosidade , alfa-Ciclodextrinas/químicaRESUMO
The flavonoid naringenin (NAR) exhibits an outstanding anti-inflammatory potential; however, stability problems and reduced solubility hinder its commercial insertion. This work aimed to obtain solid-state hydroxypropyl-ß-cyclodextrin (CD) inclusion complexes with NAR using, for the first time, the solvent change precipitation method. For this, molecular modeling and physicochemical characterizations were conducted, followed by in vitro and in vivo assays. The complexation method showed thermal and spectroscopic evidence of NAR inclusion complexes formation, suggesting an improvement of its stability. Additionally, 30â¯min-dissolution efficiency of the complex was 57.2 %, whereas NAR, as supplied, showed only 14.3 %, a four-fold enhancement. In vitro and in vivo performance attested the potent anti-inflammatory and antinociceptive profile of NAR with significant suppression of TNF-α production. Moreover, NAR complexation with CD improved its therapeutic effect, which showed similar activity to that achieved with NAR as supplied but employing only 1/5 of its dose.
Assuntos
2-Hidroxipropil-beta-Ciclodextrina/química , Anti-Inflamatórios/química , Flavanonas/química , Flavonoides/química , 2-Hidroxipropil-beta-Ciclodextrina/farmacologia , Anti-Inflamatórios/farmacologia , Varredura Diferencial de Calorimetria , Flavanonas/farmacologia , Flavonoides/farmacologia , Regulação da Expressão Gênica/efeitos dos fármacos , Humanos , Inflamação/tratamento farmacológico , Modelos Moleculares , Solubilidade , Solventes/química , Espectroscopia de Infravermelho com Transformada de Fourier , Fator de Necrose Tumoral alfa/genética , Difração de Raios XRESUMO
The subdivision of sustained release tablets is a controversial issue, especially concerning its impact on dissolution profiles. The purpose of this study was to elucidate the behavior upon subdivision of this class of tablets. For this, three common sustained release matrices containing different technologies were selected, e.g., a tablet comprised of a multiple-unit particulate system (MUPS), a lipid matrix tablet, and a polymeric inert matrix tablet. These tablets were studied concerning their physicochemical performance, dissolution rate, and kinetic profile before and after their subdivision. When subdivision occurred in the scoreline, mass variation and mass loss were below the mean values described in the literature. The dissolution of tablets with inert matrices and some lipid tablets that had their matrices preserved along the dissolution was influenced directly by tablet surface area, which increased after the subdivision. Such a result implies possible clinical consequences, especially in the case of drugs with a narrow therapeutic window, such as clomipramine. Conversely, the subdivision of MUPS tablets did not interfere in the dissolution profile since the drug was released from the granules that resulted from tablet disintegration. Hence, MUPS technology is the most recommended to produce sustained release matrix tablets intended for dose adjustment upon subdivision.
Assuntos
Preparações de Ação Retardada/química , Comprimidos/química , Tecnologia Farmacêutica/métodos , Preparações de Ação Retardada/farmacocinética , Polímeros/química , Polímeros/farmacocinética , Solubilidade , Comprimidos/farmacocinéticaRESUMO
The subdivision behavior of polymeric tablets produced with the well-known polymers Soluplus® (SOL), polyvinyl pyrrolidone co-vinyl acetate (PVPVA) and hydroxypropyl methylcellulose (HPMC) was evaluated in this study. The polymeric tablets were submitted to different post-treatments (aging, thermal and exposure to compressed gaseous carbon dioxide) and its mechanical, spectroscopic and microstructure properties were assessed. SOL tablets showed the best results for tablet subdivision, particularly, the mean mass variation (3.9%) was significantly lower than the other two polymeric tablets (7.2% and 9.1% for PVPVA and HPMC, respectively), and showed better results than common tablets produced from powder matrices (7-14%). SOL tablets were also more sensitive to the different post-treatments applied, which reduced the mass loss and friability from 1.5% and 0.8%, respectively, to values close to zero and without altering their porosity. The thermal treatment of PVPVA tablets, in turn, also led to similar subdivision results, with mass loss of 0.3% and friability of 0.02%. In contrast, the granules of HPMC presented compaction difficulties making its tablets unsuitable for the subdivision process, even after additional post-treatment. Polymeric matrices with uniform internal structure and appropriate mechanical strength are the key to a better adaptation for the tablet subdivision.
Assuntos
Derivados da Hipromelose/química , Polietilenoglicóis/química , Polivinil/química , Povidona/análogos & derivados , Dióxido de Carbono/química , Temperatura Alta , Povidona/química , ComprimidosRESUMO
Citral (CIT) is a monoterpene formed by the geranial and neral stereoisomers. CIT is the major compound of Cymbopogon citratus essential oil, commonly known as "lemongrass", and has demonstrated potential antihyperalgesic, anti-nociceptive and anti-inflammatory effects. However, CIT shows high volatility, low solubility in water and consequent low bioavailability, which limits its use. Therefore, the aim of this study was to evaluate cell viability, anti-hyperalgesic and anti-inflammatory effects of inclusion complexes of CIT on ß-cyclodextrin (ß-CD) and hydroxypropyl-ß-cyclodextrin (HP-ß-CD). Initially, physical mixture (PM) and freeze-dried inclusion (FD) complexes of CIT/ß-CD and CIT/HP-ß-CD were obtained in the molar ratio (1:1). The samples were characterized by DSC, TG/DTG, FT-IR, XRD, SEM and the complexation efficiency were performed by HPLC. Cell viability assay was performed by rezasurin reduction technique in J774 macrophages cell line. The motor activity through rota rod apparatus, mechanical hyperalgesia and pleurisy induced by carrageenan were evaluated in mice. The complexation of CIT was evidenced with ß-CD and HP-ß-CD by the characterization techniques analyzed. The complexation efficiency of CIT/ß-CD and CIT/HP-ß-CD were 78.6% and 71.7%, respectively. The CIT, CIT/ß-CD and CIT/HP-ß-CD showed cell viability in macrophages and did not interfere in the motor activity of mice. Besides that, the samples demonstrated antihyperalgesic and anti-inflammatory activity due to the reduction in total leukocytes and TNF-α levels. However, CIT/ß-CD has better pharmacological effects among the three samples evaluated. Therefore, CIT/ß-CD has potential for the development of products to treat inflammatory and pain reactions.
Assuntos
2-Hidroxipropil-beta-Ciclodextrina/farmacologia , Anti-Inflamatórios/farmacologia , Modelos Animais de Doenças , Hiperalgesia/tratamento farmacológico , Inflamação/tratamento farmacológico , Monoterpenos/farmacologia , beta-Ciclodextrinas/farmacologia , Monoterpenos Acíclicos , Animais , Comportamento Animal/efeitos dos fármacos , Carragenina/toxicidade , Quimioterapia Combinada , Hiperalgesia/induzido quimicamente , Hiperalgesia/patologia , Inflamação/induzido quimicamente , Inflamação/patologia , Masculino , CamundongosRESUMO
The aim of this study was to improve the physicochemical properties of cocoa extract (CE) using hot-melt extrusion (HME) for pharmaceutical proposes. A mixture design was applied using three distinct hydrophilic polymeric matrices (Soluplus, Plasdone S630, and Eudragit E). Systems obtained by HME were evaluated using morphologic, chromatographic, thermic, spectroscopic, and diffractometric assays. The flow, wettability, and dissolution rate of HME powders were also assessed. Both CE and its marker theobromine proved to be stable under heating according to thermal analysis and Arrhenius plot under isothermal conditions. Physicochemical analysis confirmed the stability of CE HME preparations and provided evidence of drugâ»polymer interactions. Improvements in the functional characteristics of CE were observed after the extrusion process, particularly in dissolution and flow properties. In addition, the use of a mixture design allowed the identification of synergic effects by excipient combination. The optimized combination of polymers obtained considering four different aspects showed that a mixture of the Soluplus, Plasdone S630, and Eudragit E in equal proportions produced the best results (flowability index 88%; contact angle 47°; dispersibility 7.5%; and dissolution efficiency 87%), therefore making the pharmaceutical use of CE more feasible.
RESUMO
Hot-melt extrusion (HME) has gained increasing attention in the pharmaceutical industry; however, its potential in the preparation of solid self-emulsifying drug delivery systems (S-SMEDDS) is still unexplored. This study sought to prepare enteric S-SMEDDS by HME and evaluate the effects of the process and formulation variables on S-SMEDDS properties via Box-Behnken design. Liquid SMEDDS were developed, and carvedilol was used as a class II model drug. Mean size, polydispersity index (PdI) and zeta potential of the resulting microemulsions were determined. The extrudates were then obtained by blending the lipid mixture and HPMCAS using a twin-screw hot-melt extruder. SEM, optical microscopy and PXRD were used to characterize the extrudates. In vitro microemulsion reconstitution and drug release were also studied. L-SMEDDS gave rise to microemulsions with low mean size, PdI and zeta potential (140.04⯱â¯7.22â¯nm, 0.219⯱â¯0.011 and -9.77⯱â¯0.86â¯mV). S-SMEDDS were successfully prepared by HME, and an HMPCAS matrix was able to avoid microemulsion reconstitution and retain drug release in pH 1.2 (12.97%-25.54%). Conversely, microemulsion reconstitution and drug release were gradual in pH 6.8 and complete for some formulations. Extrudates prepared at the lowest drug concentration and highest temperature and recirculation time promoted a complete and rapid drug release in pH 6.8 giving rise to small and uniform microemulsion droplets.
Assuntos
Química Farmacêutica/métodos , Sistemas de Liberação de Medicamentos , Emulsões/química , Carbazóis/administração & dosagem , Carbazóis/farmacocinética , Carvedilol , Química Farmacêutica/instrumentação , Liberação Controlada de Fármacos , Temperatura Alta , Concentração de Íons de Hidrogênio , Lipídeos/química , Metilcelulose/análogos & derivados , Metilcelulose/química , Tamanho da Partícula , Propanolaminas/administração & dosagem , Propanolaminas/farmacocinética , SolubilidadeRESUMO
This study aimed to mask fluconazole (FLU) taste and improve its rheological properties by an efficient process of cyclodextrin complexation. For this, hot-melt extrusion (HME) was used to obtain extrudates composed of FLU, hydroxypropylcellulose, and one of two different cyclodextrins (ß-cyclodextrin or hydroxypropyl-ß-cyclodextrin) maintaining the drug:cyclodextrin molar ratio at 1:0.3 or 1:0.2, respectively. Samples were characterized by physicochemical tests, palatability using e-tongue and antifungal assays. Drug stability was preserved after HME, according to spectroscopy test (correlation coefficient >0.9) and HPLC-assay (100-107%). Flowability was improved in HME systems with compressibility of <12%. Similarly, floodability exhibited significant enhancement (dispersibility <10%). Whereas extrudates of FLU containing only the polymeric matrix led to a slow drug dissolution efficiency (18.6%) and a partial drug taste masking; extrudates containing cyclodextrin accelerated FLU dissolution (dissolution efficiency approx. 30%) and provided a complete drug taste masking. Moreover, HME process could produce drug complexes with high complexation efficiency and preserve its antifungal activity.
Assuntos
Antifúngicos/química , Fluconazol/química , Paladar , beta-Ciclodextrinas/química , Antifúngicos/farmacologia , Candida/efeitos dos fármacos , Nariz Eletrônico , Fluconazol/farmacologia , Reologia , Solubilidade , beta-Ciclodextrinas/farmacologiaRESUMO
This work aimed at obtaining an optimized itraconazole (ITZ) solid oral formulation in terms of palatability and dissolution rate by combining different polymers using hot melt extrusion (HME), according to a simplex centroid mixture design. For this, the polymers Plasdone® (poly(1-vinylpyrrolidone-co-vinyl acetate) [PVP/VA]), Klucel® ELF (2-hydroxypropyl ether cellulose [HPC]), and Soluplus® (SOL, polyvinyl caprolactam-polyvinyl acetate-polyethylene glycol) were processed using a laboratory HME equipment operating without recirculation at constant temperature. Samples were characterized by physicochemical assays, as well as dissolution rate and palatability using an e-tongue. All materials became homogeneous and dense after HME processing. Thermal and structural analyses demonstrated drug amorphization, whereas IR spectroscopy evidenced drug stability and drug-excipient interactions in HME systems. Extrudates presented a significant increase in dissolution rate compared to ITZ raw material, mainly with formulations containing PVP/VA and HPC. A pronounced improvement in taste masking was also identified for HME systems, especially in those containing higher amounts of SOL and HPC. Data showed polymers act synergistically favoring formulation functional properties. Predicted best formulation should contain ITZ 25.0%, SOL 33.2%, HPC 28.9%, and PVP/VA 12.9% (w/w). Optimized response considering dissolution rate and palatability reinforces the benefit of polymer combinations.
Assuntos
Itraconazol/química , Celulose/análogos & derivados , Celulose/química , Química Farmacêutica/métodos , Composição de Medicamentos/métodos , Excipientes/química , Temperatura Alta , Polietilenoglicóis/química , Polímeros/química , Polivinil/química , Pirrolidinas/química , Solubilidade , Compostos de Vinila/químicaRESUMO
Recent advances in the treatment of Chagas disease have followed combinations of drugs that act synergistically against infection, predominantly including benznidazole (BNZ) and azoles derivatives. Possible incompatibilities between these drugs, slow dissolution of BNZ and dose adjustment difficulties are technological obstacles to the development of multidrug formulations. Thus, in the present study, BNZ pellets were developed using extrusion spheronization for immediate drug delivery. Preformulation studies were then performed using thermal analysis and infrared spectroscopy and compatibility between the drug and selected excipients (polyethylene glycol 6000, sodium starch glycolate, microcrystalline cellulose and sodium croscarmellose) was investigated. No chemical decomposition of BNZ was observed, even in samples submitted to wet granulation and thermal stress. Subsequently, formulations were elaborated according to a simplex lattice experimental design using polyethylene glycol, sodium starch glycolate and sodium croscarmellose as disintegrating agents. In these experiments, BNZ pellets showed appropriate physicochemical characteristics, including high drug load capacity and excellent flow properties. The mixture experimental design allowed identification of adequate compositions of disintegrating agents and achieved rapid disintegration and dissolution of pellets. Optimum performance was achieved using polyethylene glycol and sodium croscarmellose at 5.0% w/w each. The present BNZ pellets are versatile alternatives to treat Chagas disease and provide insights into the preparation of multidrug systems.
Assuntos
Composição de Medicamentos/métodos , Implantes de Medicamento/química , Nitroimidazóis/química , Ácidos Polimetacrílicos/química , Carboximetilcelulose Sódica/química , Celulose/química , Química Farmacêutica/métodos , Sistemas de Liberação de Medicamentos/métodos , Excipientes/química , Polietilenoglicóis/química , Solubilidade , Amido/análogos & derivados , Amido/químicaRESUMO
This work aimed at developing enalapril maleate granules in order to improve its stability in solid dosage form. Granules were prepared by hot melt granulation using a fluidized bed apparatus. Gelucire 50/13®, polyethylene glycol 6000 e Poloxamer 407® were studied and compared as binders in 2 × 2 factorial designs where the proportions of enalapril maleate, binders and spray dried lactose were varied. The granulation process resulted in high yields and granule sizes that indicated the prevalence of particles coating. Furthermore, the granules obtained showed adequate flowability and a fast dissolution rate of enalapril maleate with almost 100% of the drug released in 10 min. The stability of enalapril maleate in hard gelatin capsules showed that the drug stability was greatly increased in granules, since for raw drug, the remaining content of enalapril maleate after 91 days was 68.4% and, for granules, the content was always above 93%. This result was confirmed by the quantification of the degradation products, enalaprilat and diketopiperazine, which were found in very low content in granules samples. The results demonstrate that fluidized bed hot melt granulation with hydrophilic binders is a suitable alternative for improving the chemical stability of enalapril maleate.
Assuntos
Enalapril/química , Tecnologia Farmacêutica , Estabilidade de MedicamentosRESUMO
OBJECTIVES: This study sought to evaluate the achievement of carvedilol (CARV) inclusion complexes with modified cyclodextrins (HPßCD and HPγCD) using fluid-bed granulation (FB). METHODS: The solid complexes were produced using FB and spray drying (SD) and were characterised by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), powder X-ray diffraction, SEM, flowability and particle size analyses and in vitro dissolution. KEY FINDINGS: The DSC, FTIR and powder X-ray diffraction findings suggested successful CARV inclusion in the modified ß- and γ-cyclodextrins, which was more evident in acidic media. The CARV dissolution rate was ~7-fold higher for complexes with both cyclodextrins prepared using SD than for raw CARV. Complexes prepared with HPßCD using FB also resulted in a significant improvement in dissolution rate (~5-fold) and presented superior flowability and larger particle size. CONCLUSIONS: The findings suggested that FB is the best alternative for large-scale production of solid dosage forms containing CARV. Additionally, the results suggest that HPγCD could be considered as another option for CARV complexation because of its excellent performance in inclusion complex formation in the solid state.