Short communication: Volatiles in microfluidized raw and heat-treated milk.

As innovative processing equipment is introduced to milk processing, it is essential to determine its effect on milk aroma, a critical factor in consumer acceptance of the final dairy product. Microfluidization is known to cause severe high-pressure homogenization of milk fat and, although severe processing is known to release undesired aromas, no information is available on the levels of the volatile compounds in milk immediately after microfluidization. We hypothesized that microfluidization would alter levels of volatile compounds in milk that may affect aroma. The concentration of 11 selected volatile compounds in raw, thermized, pasteurized, and UHT 3.0% fat milk samples were compared before and after microfluidization at 170 MPa and common 2-stage homogenization at 15 MPa. Overall, the different milk samples had similar trends in response to homogenization, although UHT milk started with lower values of nonanoic acid, and acetone and higher levels of hexanal and heptanol. In many cases, microfluidization did not significantly alter volatile levels compared with the starting milk. Heptanal was the only compound observed to increase in thermized and UHT milk, whereas nonanoic acid and acetone decreased in raw, thermized, and pasteurized milks and octanoic acid decreased in thermized and UHT milks. The highest levels of almost all of the volatiles were found in the 2-stage homogenized milk. Overall, microfluidization had minimal effect on the volatile compound profiles of milk, although sensory evaluation is needed to confirm effects on aroma and flavor.

Characterization of the physical, microbiological, and chemical properties of sonicated raw bovine milk.

Innovative processing technologies, such as ultrasonication, can change the properties of milk, allowing for the improvement or development of dairy foods. Yet taking bench-scale equipment to pilot plant scale has been challenging. Raw milk, standardized to 3% fat and warmed to inlet temperatures of 42 or 54°C, was exposed to continuous, high-intensity, low-frequency ultrasonication (16/20 kHz, 1.36 kW/pass) at flow rates of 0.15, 0.30, and 0.45 L/min that resulted in resident times within the reaction cell of 6, 3, and 2 min per pass, respectively. Multiple passes (3, 5, and 7, respectively) were required to obtain a total exposure time of 14 to 18 min. Evaluation of fat droplet sizes, enzyme coagulation properties, and microstructure of milk and milk gels, as well as determining compositional and lipid properties, were conducted to determine the potential of the ultrasound system to effectively modify milk. Laser scanning particle sizing and confocal microscopy showed that the largest droplets (2.26 ± 0.13 µm) found in raw milk were selectively reduced in size with a concomitant increase in the number of submicron droplets (0.37 ± 0.06 µm), which occurred sooner when exposed to shorter bursts of ultrasonication (0.45 L/min flow rates) and at an inlet temperature of 54°C. Ultrasound processing with milk entering at 42°C resulted in faster gelling times and firmer curds at 30 min; however, extended processing at inlet temperature of 54°C reduced curd firmness and lengthened coagulation time. This showed that ultrasonication altered protein-protein and protein-lipid interactions, thus the strength of the enzyme-set curds. Scanning electron microscopy revealed a denser curd matrix with less continuous and more irregular shaped and clustered strands, whereas transmission electron microscopy showed submicron lipid droplets embedded within the protein strands of the curd matrix. Processing at inlet temperature of 54°C with flow rates of 0.30 and 0.45 L/min also reduced the total aerobic bacterial count by more than 1 log cfu/mL, and the number of psychrophiles below the limit of detection (10 cfu/mL) for this study. Ultrasonication exposures of 14 to 18 min had minimal effect on the milk composition, fatty acid profiles, and lipid heat capacity and enthalpy. The findings show that this continuous ultrasound system, which is conducive to commercial scale-up, modifies the physical and functional properties of milk under the parameters used in this study and has potential use in dairy processing.

The effects of microfluidization on the physical, microbial, chemical, and coagulation properties of milk.

This work examines the use of mild heat treatments in conjunction with 2-pass microfluidization to generate cheese milk for potential use in soft cheeses, such as Queso Fresco. Raw, thermized, and high temperature, short time pasteurized milk samples, standardized to the 3% (wt/wt) fat content used in cheesemaking, were processed at 4 inlet temperature and pressure conditions: 42°C/75 MPa, 42°C/125 MPa, 54°C/125 MPa, and 54°C/170 MPa. Processing-induced changes in the physical, chemical, and microbial properties resulting from the intense pressure, shear, and cavitation that milk experiences as it is microfluidized were compared with nonmicrofluidized controls. A pressure-dependent increase in exit temperature was observed for all microfluidized samples, with inactivation of alkaline phosphatase in raw and thermized samples at 125 and 170 MPa. Microfluidization of all samples under the 4 inlet temperature and processing pressure conditions resulted in a stable emulsion of fat droplets ranging from 0.390 to 0.501 µm, compared with 7.921 (control) and 4.127 (homogenized control) µm. Confocal imaging showed coalescence of scattered fat agglomerates 1 to 3 µm in size during the first 24 h. We found no changes in fat, lactose, ash content or pH, indicating the major components of milk remained unaffected by microfluidization. However, the apparent protein content was reduced from 3.1 to 2.2%, likely a result of near infrared spectroscopy improperly identifying the micellar fragments embedded into the fat droplets. Microbiology results indicated a decrease in mesophilic aerobic and psychrophilic milk microflora with increasing temperature and pressure, suggesting that microfluidization may eliminate bacteria. The viscosities of milk samples were similar but tended to be higher after treatment at 54°C and 125 or 170 MPa. These samples exhibited the longest coagulation times and the weakest gel firmness, indicating that formation of the casein matrix, a critical step in the production of cheese, was affected. Low temperature and pressure (42°C/75 MPa) exhibited similar coagulation properties to controls. The results suggest that microfluidization at lower pressures may be used to manufacture high-moisture cheese with altered texture whereas higher pressures may result in novel dairy ingredients.

Comparing the effect of homogenization and heat processing on the properties and in vitro digestion of milk from organic and conventional dairy herds.

We compared the effects of homogenization and heat processing on the chemical and in vitro digestion traits of milk from organic and conventional herds. Raw milk from organic (>50% of dry matter intake from pasture) and conventional (no access to pasture) farms were adjusted to commercial whole and nonfat milk fat standards, and processed with or without homogenization, and with high-temperature-short-time or UHT pasteurization. The milk then underwent in vitro gastrointestinal digestion. Comparison of milk from organic and conventional herds showed that the milks responded to processing in similar ways. General composition was the same among the whole milk samples and among the nonfat milk samples. Protein profiles were similar, with intact caseins and whey proteins predominant and only minor amounts of peptides. Whole milk samples from grazing cows contained higher levels of α-linolenic (C18:3), vaccenic (C18:1 trans), and conjugated linoleic acids, and lower levels of palmitic (C16:0) and stearic (C18:0) acids than samples from nongrazing cows. Processing had no effect on conjugated linoleic acid and linolenic acid levels in milk, although homogenization resulted in higher levels of C8 to C14 saturated fatty acids. Of the 9 volatile compounds evaluated, milk from grazing cows contained lower levels of 2-butanone than milk from nongrazing cows, and milk from both farms showed spikes for heptanal in UHT samples and spikes for butanoic, octanoic, nonanoic, and N-decanoic acids in homogenized samples. At the start of in vitro digestion, nonfat raw and pasteurized milk samples formed the largest acid clots, and organic milk clots were larger than conventional milk clots; UHT whole milk formed the smallest clots. Milk digests from grazing cows had lower levels of free fatty acids than digests from nongrazing cows. In vitro proteolysis was similar in milk from both farms and resulted in 85 to 95% digestibility. Overall, milk from organic/grass-fed and conventional herds responded in similar ways to typical homogenization and heat processing used in United States dairy plants and showed only minor differences in chemical traits and in vitro digestion. Findings from this research enhance our knowledge of the effect of processing on the quality traits and digestibility of milk from organic/pasture-fed and confined conventional herds and will help health-conscious consumers make informed decisions about dairy selections.

Characterization of starter-free Queso Fresco made with sodium-potassium salt blends over 12 weeks of 4°C storage.

Development of reduced-sodium cheese to meet the demands of consumers concerned about sodium levels in their diet is challenging when a high-moisture, higher pH, fresh cheese, such as Queso Fresco (QF), depends on its NaCl salt content to obtain its signature flavor and quality traits. This study evaluated the effects of different Na-K salt blends on the compositional, sensorial, microbial, functional, and rheological properties of QF stored for up to 12 wk at 4°C. Queso Fresco curd from each vat was divided into 6 portions and salted with different blends of NaCl-KCl (Na-K, %): 0.75-0.75, 1.0-0.5, 1.0-1.0, 1.0-1.3, 1.0-1.5, and 2.0-0 (control). Within this narrow salt range (1.5 to 2.5% total salt), the moisture, protein, fat, and lactose levels; water activity; pH; and the textural and rheological properties were not affected by salt treatment or aging. The total salt, sodium, potassium, and ash contents reflected the different Na-K ratios added to the QF. Total aerobic microbial count, overall proteolysis, the release of casein phosphopeptides, and the level of volatile compounds were affected by aging but not by the salt treatment. Only the 1.0-1.3 and 1.0-1.5 Na-K cheeses had sensory saltiness scores similar to that of the 2.0-0 Na-K control QF. Loss of free serum from the cheese matrix increased steadily over the 12 wk, with higher losses found in QF containing 1.5% total salt compared with the higher Na-K blends. In conclusion, KCl substitution is a viable means for reduction of sodium in QF resulting in only minor differences in the quality traits, and levels of 1.0-1.3 and 1.0-1.5 Na-K are recommended to match the saltiness intensity of the 2.0-0 Na-K control. The findings from this study will aid cheese producers in creating reduced-sodium QF for health-conscious consumers.

Hot topic: Brown marmorated stink bug odor compounds do not transfer into milk by feeding bug-contaminated corn silage to lactating dairy cattle.

Brown marmorated stink bug (BMSB; Halyomorpha halys) is an emerging invasive species of grave concern to agriculture as a polyphagous plant pest with potential negative effects on the dairy industry. The purpose of this study was to determine the risk of including BMSB-contaminated silage in lactating dairy cow rations. First, 6 dairies, either highly infested (n=3; 30 to 100 bugs per stalk) or not infested (n=3), were sampled to assess the prevalence of bug secretion compounds tridecane (major component) and E-2-decenal (stink odor component) in silage and milk. Second, using wild BMSB, a mini-silo dose-response experiment (adding 100, 50, 25, 10, and 1 freshly crushed bugs/0.5kg of chopped corn) was conducted to assess the effect of ensiling on BMSB stink odor compounds. Finally, synthetic BMSB stink odor compounds (10g of tridecane and 5g of E-2-decenal) were ruminally infused twice daily over 3 d, and samples of milk, urine, and rumen fluid were collected to evaluate disposition. Bug stink odor compounds were sampled by solid-phase microextraction (SPME) and analyzed by gas chromatography-mass spectrometry (GC-MS). Milk production and feed composition were unaffected when BMSB-contaminated silage was fed. Moreover, no E-2-decenal was detected in silage or milk (detection threshold = 0.00125µg/mL). The dose-response of tridecane in mini-silo samples exhibited a linear relationship (R(2)=0.78) with the amount of BMSB added; however, E-2-decenal was completely decomposed and undetectable in spiked mini-silos after ensiling. Both synthetic secretion compounds infused into rumen were undetectable in all milk and urine samples. E-2-Decenal was not detectable in rumen fluid, whereas tridecane was detected only at 15 min postinfusion but not present thereafter. Feed intake was unaffected by infusion treatment and BMSB secretion compounds (E-2-decenal and tridecane) were not observed in milk. E-2-Decenal and tridecane from the metathoracic gland of BMSB are not able to contaminate milk either due to the ensiling process or because of metabolism within the rumen. Concern over BMSB stink odor compounds contaminating the fluid milk supply, even on highly infested farms, is not warranted.

Effect of high-pressure processing on reduction of Listeria monocytogenes in packaged Queso Fresco.

The effect of high-hydrostatic-pressure processing (HPP) on the survival of a 5-strain rifampicin-resistant cocktail of Listeria monocytogenes in Queso Fresco (QF) was evaluated as a postpackaging intervention. Queso Fresco was made using pasteurized, homogenized milk, and was starter-free and not pressed. In phase 1, QF slices (12.7 × 7.6 × 1 cm), weighing from 52 to 66 g, were surface inoculated with L. monocytogenes (ca. 5.0 log10 cfu/g) and individually double vacuum packaged. The slices were then warmed to either 20 or 40°C and HPP treated at 200, 400, and 600 MPa for hold times of 5, 10, 15, or 20 min. Treatment at 600 MPa was most effective in reducing L. monocytogenes to below the detection level of 0.91 log10 cfu/g at all hold times and temperatures. High-hydrostatic-pressure processing at 40°C, 400 MPa, and hold time ≥ 15 min was effective but resulted in wheying-off and textural changes. In phase 2, L. monocytogenes was inoculated either on the slices (ca. 5.0 log10 cfu/g; ON) or in the curds (ca. 7.0 log10 cfu/g; IN) before the cheese block was formed and sliced. The slices were treated at 20°C and 600 MPa at hold times of 3, 10, and 20 min, and then stored at 4 and 10°C for 60 d. For both treatments, L. monocytogenes became less resistant to pressure as hold time increased, with greater percentages of injured cells at 3 and 10 min than at 20 min, at which the lethality of the process increased. For the IN treatment, with hold times of 3 and 10 min, growth of L. monocytogenes increased the first week of storage, but was delayed for 1 wk, with a hold time of 20 min. Longer lag times in growth of L. monocytogenes during storage at 4°C were observed for the ON treatment at hold times of 10 and 20 min, indicating that the IN treatment may have provided a more protective environment with less injury to the cells than the ON treatment. Similarly, HPP treatment for 10 min followed by storage at 4°C was the best method for suppressing the growth of the endogenous microflora with bacterial counts remaining below the level of detection for 2 out of the 3 QF samples for up to 84 d. Lag times in growth were not observed during storage of QF at 10°C. Although HPP reduced L. monocytogenes immediately after processing, a second preservation technique is necessary to control growth of L. monocytogenes during cold storage. However, the results also showed that HPP would be effective for slowing the growth of microorganisms that can shorten the shelf life of QF.

Effect of hydrostatic high-pressure processing on the chemical, functional, and rheological properties of starter-free Queso Fresco.

Queso Fresco (QF), a popular high-moisture, high-pH Hispanic-style cheese sold in the United States, underwent high-pressure processing (HPP), which has the potential to improve the safety of cheese, to determine the effects of this process on quality traits of the cheese. Starter-free, rennet-set QF (manufactured from pasteurized, homogenized milk, milled before hooping, and not pressed) was cut into 4.5- × 4.5- × 15-cm blocks and double vacuum packaged. Phase 1 of the research examined the effects of hydrostatic HPP on the quality traits of fresh QF that had been warmed to a core temperature of 20 or 40 °C; processed at 200, 400, or 600 MPa for 5, 10, or 20 min; and stored at 4 °C for 6 to 8d. Phase 2 examined the long-term effects of HPP on quality traits when QF was treated at 600 MPa for 3 or 10 min, and stored at 4 or 10 °C for up to 12 wk. Warming the QF to 40 °C before packaging and exposure to high pressure resulted in loss of free whey from the cheese into the package, lower moisture content, and harder cheese. In phase 2, the control QF, regardless of aging temperature, was significantly softer than HPP cheeses over the 12 wk of storage. Hardness, fracture stress, and fracture rigidity increased with length of exposure time and storage temperature, with minor changes in the other properties. Queso Fresco remained a bright white, weak-bodied cheese that crumbled and did not melt upon heating. Although high pressures or long processing times may be required for the elimination of pathogens, cheese producers must be aware that HPP altered the rheological properties of QF and caused wheying-off in cheeses not pressed before packaging.

Impact of curd milling on the chemical, functional, and rheological properties of starter-free Queso Fresco.

The manufacture of Queso Fresco (QF), a high-moisture fresh Mexican cheese that is popular in the Americas, varies from country to country, with many manufacturers milling the curd before forming the cheese block to disrupt the protein matrix and ensure the crumbly nature of the QF. Because this traditional milling step does take time and may be an unnecessary point of microbial contamination, this study was undertaken to determine whether the curd-milling step could be omitted without altering the chemical, functional, and textural properties of the QF. Starter culture-free, rennet-set QF was prepared from pasteurized, homogenized milk. Curds were cooked at 39°C for 30 min, wet salted at 1.45 g of NaCl/100 g of milk, chilled, and divided into 4 portions. Curds were not milled or were subjected to coarse, medium, or fine milling and hand-packed into molds. After 12h at 4°C, the cheese was divided, vacuum packaged, and stored at 4°C for up to 8 wk. Fresh QF contained 57.3 ± 1.2% moisture, 20.9±0.8% fat, 16.0 ± 1.3% protein, 2.61 ± 0.15% lactose, and 2.25 ± 0.22% salt and had a pH of 6.36 ± 0.03%. Moisture decreased over the 8 wk of storage, whereas the fat level tended to increase. All cheeses lost 1.3 to 1.7% of their weight in whey during the first week after manufacture, and the weight gradually increased to 2.1% (nonmilled) to 3.2% (milled) by wk 8. Milling did result in QF that were softer, less chewy, and less rigid and with lower viscoelastic properties than nonmilled cheeses. Sensory panelists differentiate the finely milled QF from the other treatments, but they detected no significant differences among the nonmilled, coarsely milled, and medium-milled QF. Milling of the curd did not affect the ability of Listeria monocytogenes to grow on the cheese surface. Results from this study indicate that the milling step, which lengthens the manufacturing time, does increase wheying off during storage and results in a more fragile protein matrix. Cheese manufacturers can use this information to produce a QF that meets the demands of their customers.

Mexican Queso Chihuahua: functional properties of aging cheese.

Queso Chihuahua, a semi-hard cheese manufactured from raw milk (RM) in northern Mexico, is being replaced by pasteurized milk (PM) versions because of food safety concerns and the desire for longer shelf life. In this study, the functional traits of authentic Mexican Queso Chihuahua made from RM or PM were characterized to identify sources of variation and to determine if pasteurization of the cheese milk resulted in changes to the functional properties. Two brands of RM cheese and 2 brands of PM cheese obtained in 3 seasons of the year from 4 manufacturers in Chihuahua, Mexico, were analyzed after 0, 4, 8, 12, and 16 wk of storage at 4°C. A color measurement spectrophotometer was used to collect color data before and after heating at 232°C for 5 min or 130°C for 75 min. Meltability was measured using the Schreiber Melt Test on samples heated to 232°C for 5 min. Sliceability (the force required to cut through a sample) was measured using a texture analyzer fitted with a wire cutter attachment. Proteolysis was tracked using sodium dodecyl sulfate-PAGE. Compared with PM cheeses, RM cheeses showed less browning upon heating, melted more at 232°C, and initially required a greater cutting force. With aging, cheeses increased in meltability, decreased in whiteness when measured before heating, and required less cutting force to slice. Seasonal variations in the cheesemilk had minimal or no effect on the functional properties. The differences in the functional properties can be attributed, in part, to the mixed microflora present in the RM cheeses compared with the more homogeneous microflora added during the manufacture of PM cheeses. The degree of proteolysis and subsequent integrity of the cheese matrix contribute to melt, slice, and color properties of the RM and PM cheeses. Understanding the functional properties of the authentic RM cheeses will help researchers and cheesemakers develop pasteurized versions that maintain the traditional traits desired in the cheeses.

Short communication: characterization of microflora in Mexican Chihuahua cheese.

This work was performed to identify the bacterial species present in 10 Chihuahua cheeses obtained from commercial producers in Mexico using 16S rRNA gene analysis. As expected, some of the agar media initially used for isolation were not very selective, supporting the growth of several unrelated bacterial species. Sequence analysis identified potential pathogens, including Escherichia coli and Staphylococcus aureus, in all raw milk samples and 2 pasteurized milk samples. Streptococcus thermophilus and Lactococcus lactis ssp. lactis were identified in 9 and 6 samples, respectively, and would serve as acidifying agents during cheese production. Lactobacilli were identified in all cheeses, with the most prevalent being Lactobacillus plantarum identified in 7 raw milk and 1 pasteurized milk cheeses. Leuconostoc mesenteroides and Streptococcus macedonicus were identified in 4 raw milk cheeses and both were present in all pasteurized milk samples, suggesting that they may play a role in the development of traditional Chihuahua cheese attributes.

Short communication: Assessing antihypertensive activity in native and model Queso Fresco cheeses.

Hispanic-style cheeses are one of the fastest growing varieties in the United States, making up approximately 2% of the total cheese production in this country. Queso Fresco is one of most popular Hispanic-style cheeses. Protein extracts from several varieties of Mexican Queso Fresco and model Queso Fresco were analyzed for potential antihypertensive activity. Many Quesos Frescos obtained from Mexico are made from raw milk and therefore the native microflora is included in the cheese-making process. Model Queso Fresco samples were made from pasteurized milk and did not utilize starter cultures. Water-soluble protein extracts from 6 Mexican Quesos Frescos and 12 model cheeses were obtained and assayed for their ability to inhibit angiotensin-converting enzyme, implying potential as foods that can help to lower blood pressure. All model cheeses displayed antihypertensive activity, but mainly after 8 wk of aging when they were no longer consumable, whereas the Mexican samples did display some angiotensin-converting enzyme inhibitory action after minimal aging.

Fate of lysostaphin in milk from individual cows through pasteurization and cheesemaking.

Transgenic cows secreting over 3 microg of lysostaphin/ mL of milk are protected against mastitis caused by Staphylococcus aureus, but it is unknown if active lysostaphin persists through dairy processing procedures or affects the production of fermented dairy foods. The objective of this study was to determine the fate of lysostaphin as milk was pasteurized and then processed into cheese. Raw milk from transgenic cows was heat treated at 63 degrees C for 30 min, 72 degrees C for 15 s (high temperature, short time), or 140 degrees C for 2 s (UHT). Portions of the high temperature, short-time milk were manufactured into semi-hard cheeses. Aliquots taken at each processing step were assayed to determine the quantity (ELISA) and activity (ability to inhibit S. aureus growth) of lysostaphin. Results indicated that most of the lysostaphin was present in the aqueous portion of the milk and was not affected by pasteurization, although UHT treatment reduced enzyme concentration by 60%. The quantity and activity of the lysostaphin decreased during cheesemaking. Based on the amount of lysostaphin present in the starting cheesemilk, 10 to 15% of the lysostaphin was recovered in the whey, 21 to 55% in the cheese curd at d 1, and 21 to 36% in cheese stored at 4 degrees C for 90 d. Enough of the lysostaphin secreted into milk by transgenic cows survived typical dairy processing conditions to impart potential value as a bioprotective agent against staphylococci in dairy foods.

Proteolytic and rheological properties of aging cheddar-like caprine milk cheeses manufactured at different times during lactation.

The effects of 24 wk of aging on the proteolytic and rheological properties of cheddar-like cheese made from caprine milk collected at different lactation periods were evaluated. Cheddar cheese was made weekly using whole milk from Alpine goats and cheeses manufactured at weeks 4, 5, 12, 14, 15, 21, 22, and 23 of lactation were evaluated for proteolytic and rheological properties at 5 d after manufacture and after 8, 16, and 24 wk of aging at 4 degrees C. Rheology results indicated that a minimum of 8 wk of aging was needed to stabilize the texture of the cheese and that the most uniform cheeses were made from mid lactation milk. Cheeses manufactured at weeks 12 to 15 of lactation were the firmest, had the least flexible protein matrix (highest values for hardness, chewiness, and shear stress and rigidity at point of fracture), and the lowest degree of proteolysis. Understanding the factors that impact the texture of cheese, such as aging and the period of lactation that cheesemilk is obtained, will help develop guidance for maintaining the production of high quality and uniform caprine milk cheeses.

Mexican chihuahua cheese: sensory profiles of young cheese.

Sensory profiles of fresh semihard Chihuahua cheese produced in the northern Mexican state of Chihuahua were developed to characterize the flavors and textures of this traditionally made Hispanic-style cheese. Multiple allotments of Chihuahua cheese, 9 brands made with raw milk (RM) and 5 brands made with pasteurized milk (PM), were obtained within 3 d of manufacture from 12 different cheese plants throughout Chihuahua, México. Cheeses were shipped overnight to Wyndmoor, Pennsylvania, and flavor analyses were conducted within 14 to 18 d after manufacture. Four brands (2 RM and 2 PM cheeses) were then selected and multiple allotments were shipped at 3 distinct seasons over a 1-yr period for evaluation of flavor and texture. Microbial analysis was conducted prior to testing to ensure product safety. Descriptive analyses of cheese flavors and textures were conducted with panelists trained to use a universal or product-specific Spectrum intensity scale, respectively. Sensory profiles of cheeses varied among the different manufacturers. The most prominent flavor attributes were salty, sour, diacetyl, cooked, whey, bitter, and milk-fat. The RM cheeses had more intense sour, bitter, and prickle scores than the PM cheeses. Many cheese texture attributes were similar, but RM cheeses were perceived as softer than PM cheeses. As the demand for Hispanic-style cheeses increases, defining and understanding the sensory attributes of traditionally made Mexican cheeses provides guidance to cheese manufacturers as new ways are explored to improve the production and shelf life of the cheeses.

Effect of frozen storage on the proteolytic and rheological properties of soft caprine milk cheese.

Freezing and long-term frozen storage had minimal impact on the rheology and proteolysis of soft cheese made from caprine milk. Plain soft cheeses were obtained from a grade A goat dairy in Georgia and received 4 storage treatments: fresh refrigerated control (C), aged at 4 degrees C for 28 d; frozen control (FC), stored at -20 degrees C for 2 d before being thawed and aged in the same way as C cheese; and 3-mo frozen (3MF), or 6-mo frozen (6MF), stored at -20 degrees C for 3 or 6 mo before being thawed and aged. Soft cheeses had fragile textures that showed minimal change after freezing or over 28 d of aging at 4 degrees C. The only exceptions were the FC cheeses, which, after frozen storage and aging for 1 d at 4 degrees C, were significantly softer than the other cheeses, and less chewy than the other frozen cheeses. Moreover, after 28 d of aging at 4 degrees C, the FC cheeses tended to have the lowest viscoelastic values. Slight variation was noted in protein distribution among the storage treatment, although no significant proteolysis occurred during refrigerated aging. The creation and removal of ice crystals in the cheese matrix and the limited proteolysis of the caseins showed only slight impact on cheese texture, suggesting that frozen storage of soft cheeses may be possible for year-round supply with minimal loss of textural quality.

Torsion gelometry of cheese.

Torsion gelometry, a fundamental rheological test in which specimens are twisted until they fracture, was applied to several different cheese varieties to determine its suitability for measuring their textural properties. Fresh and aged Brick, Cheddar, Colby, Gouda, Havarti, Mozzarella, and Romano cheeses were subjected to torsion analysis, and the results were compared with those from small amplitude oscillatory shear (SAOS) tests and texture profile analysis (TPA). Strong relationships (correlation coefficients > 0.8) were found between torsion shear stress and TPA hardness, and between torsion shear strain and TPA cohesiveness. SAOS, which measures rheological properties of intact samples, did not correlate well with torsion or TPA. A map showing trends during aging toward brittle, mushy, rubbery, and tough texture was drawn using the torsion data. The findings show that torsion gelometry provides fundamental rheological data on cheese at the fracture point. The information can be used to compare textural qualities of cheese samples as they are being cut.

Effect of carbon dioxide under high pressure on the survival of cheese starter cultures.

A new processing method that rapidly forms curds and whey from milk has the potential to improve cheesemaking procedures if cheese starter cultures can tolerate the processing conditions. The survival of Lactobacillus delbrueckii ssp. bulgaricus, Lactococcus lactis ssp. lactis, or Streptococcus thermophilus through this new process was evaluated. Inoculated milk containing 0, 1, or 3.25% fat or Lactobacillus MRS broth or tryptone yeast lactose broth (depending on microorganism used) was sparged with CO2 to a pressure of 5.52 MPa and held for 5 min at 38 degrees C. Broth contained 7.93 to 8.78 log CFU/ ml before processing and 7.84 to 8.66 log CFU/ml afterward. Before processing, milk inoculated with L bulgaricus, L. lactis, or S. thermophilus contained 6.81, 7.35, or 6.75 log CFU/ml, respectively. After processing, the curds contained 5.68, 7.32, or 6.50 log CFU/g, and the whey had 5.05, 6.43, or 6.14 log CFU/ml, respectively. After processing, the pHs of control samples were lower by 0.41 units in broth, 0.53 units in whey, and 0.89 units in curd. The pH of the processed inoculated samples decreased by 0.3 to 0.53 units in broth, 0.32 to 0.37 units in whey, and 0.93 to 0.98 units in the curd. Storing curds containing L. lactis at 30 degrees C or control curds and curds with L. bulgaricus or S. thermophilus at 37 degrees C for an additional 48 h resulted in pHs of 5.22, 5.41, 4.53, or 4.99, respectively. This study showed that milk inoculated with cheese starter cultures and treated with CO2 under high pressure to precipitate casein-produced curds that contained sufficient numbers of viable starter culture to produce lactic acid, thereby decreasing the pH.

Chromatographic and electrophoretic methods used for analysis of milk proteins.

Current knowledge of milk proteins and their behavior in dairy foods is based on early applications of chromatography and electrophoresis. Electrophoretic identification of the number and genetic variety of milk proteins inaugurated a research effort in which chromatographic techniques were successfully applied to the isolation of each milk protein, thus facilitating the characterization and further study of milk and dairy products. This review focuses on recent applications of chromatography for separations and analysis and on analytical applications of electrophoresis.

Application of PhastSystem to the resolution of bovine milk proteins on urea-polyacrylamide gel electrophoresis.

Optimal conditions were established for alkaline urea-PAGE using modified precast, ultrathin gradient gels on the automated PhastSystem. Profiles of milk proteins showed that the caseins and whey proteins resolved extremely well. Major bands were observed for alpha s1-casein and beta-casein, and alpha s2-casein appeared as a well-resolved doublet. In contrast, kappa-casein separated from other caseins as a faint doublet, and purified kappa-casein appeared as one major and one minor band. Whey proteins (serum albumin, alpha-lactalbumin, beta-lactoglobulin) separated into broad bands resolved from each other and from the caseins. Partially (40%) dephosphorylated whole casein showed multiple bands for alpha s1-casein and beta-casein at different levels of phosphorylation. Separation of genetic phenotypes was observed for beta-lactoglobulin A and B; alpha s1-casein A, B, and C; and beta-casein A, B, and C. Electrophoretic patterns of milk proteins extracted from cheese samples varied among the different types of cheeses. Our modified procedure provides researchers with a rapid technique to separate both caseins and whey proteins on the same urea gel according to their charge to mass ratios.