3D Porous Fibers with Spatial Traps and Excellent Zn2+ Transport Kinetics Enable Stable Zn-Based Aqueous Battery.

Adverse side reactions and uncontrolled Zn dendrites growth are the dominant factors that have restricted the application of Zn ion batteries. Herein, a 3D self-supporting porous carbon fibers (denoted as PCFs) host is developed with "trap" effect to adjust the Zn deposition. The unique open structural design of N-doped carbon can act as the zincophilic sites to induce uniform deposition and inhibit adverse side reactions. More importantly, the porous hollow PCFs host with "trap" effect can induce Zn deposition in the fiber by adjusting the local electric field and current density, thereby increasing the specific energy density of the battery and inhibiting dendrite growth. In addition, the 3D open frameworks can regulate Zn2+ flux to enable outstanding cycling performance at ultra-high current densities. As expected, the PCFs framework guarantees the uniform Zn plating and stripping with an outstanding stability over 6000 cycles at the current density of 40 mA cm-2. And the Zn@PCFs||MnO2 full battery shows an excellent lifespan over 1300 cycles at 2000 mA g-1.

Robust and Adhesive Laminar Solid Electrolyte with Homogenous and Fast Li-Ion Conduction for High-Performance All-Solid-State Lithium Metal Battery.

Constructing composite solid electrolytes (CSEs) integrating the merits of inorganic and organic components is a promising approach to developing high-performance all-solid-state lithium metal batteries (ASSLMBs). CSEs are now capable of achieving homogeneous and fast Li-ion flux, but how to escape the trade-off between mechanical modulus and adhesion is still a challenge. Herein, a strategy to address this issue is proposed, that is, intercalating highly conductive, homogeneous, and viscous-fluid ionic conductors into robust coordination laminar framework to construct laminar solid electrolyte with homogeneous and fast Li-ion conduction (LSE-HFC). A 9 µm-thick LSH-HFC, in which poly(ethylene oxide)/succinonitrile is adsorbed by coordination laminar framework with metal-organic framework nanosheets as building blocks, is used here as an example to determine the validity. The Li-ion transfer mechanism is verified and works across the entire LSE-HFC, which facilitates homogeneous Li-ion flux and low migration energy barriers, endowing LSE-HFC with high ionic conductivity of 5.62 × 10-4 S cm-1 and Li-ion transference number of 0.78 at 25 °C. Combining the outstanding mechanical strength against punctures and the enhanced adhesion force with electrodes, LSE-HFC harvests uniform Li plating/stripping behavior. These enable the realization of high-energy-density ASSLMBs with excellent cycling stability when being assembled as LiFePO4/Li and LiNi0.6Mn0.2Co0.2O2/Li cells.

Tissue and cellular localization of condensed tannins in poplar roots and potential association with nitrogen uptake.

Condensed tannins are common in vegetative tissues of woody plants, including in roots. In hybrid poplar (Populus tremula x alba; also known as P. x canescens) CT assays indicated they were most concentrated in younger white roots and at the root tip. Furthermore, CT-specific staining of embedded tissue sections demonstrated accumulation in root cap cells and adjacent epidermal cells, as well as a more sporadic presence in cortex cells. In older, brown roots as well as roots with secondary growth (cork zone), CT concentration was significantly lower. The insoluble fraction of CTs was greatest in the cork zone. To determine if CT accumulation correlates with nutrient uptake in poplar roots, a microelectrode ion flux measurement (MIFE™) system was used to measure flux along the root axis. Greatest NH4 + uptake was measured near the root tip, but NO3- and Ca2+ did not vary along the root length. In agreement with earlier work, providing poplars with ample nitrogen led to higher accumulation of CTs across root zones. To test the functional importance of CTs in roots directly, CT-modified transgenic plants could be important tools.

The effects of microplastics on ionoregulatory processes in the gills of freshwater fish and invertebrates: A prospective review.

From review of the very few topical studies to date, we conclude that while effects are variable, microplastics can induce direct ionoregulatory disturbances in freshwater fish and invertebrates. However, the intensity depends on microplastic type, size, concentration, and exposure regime. More numerous are studies where indirect inferences about possible ionoregulatory effects can be drawn; these indicate increased mucus production, altered breathing, histopathological effects on gill structure, oxidative stress, and alterations in molecular pathways. All of these could have negative effects on ionoregulatory homeostasis. However, previous research has suffered from a lack of standardized reporting of microplastic characteristics and exposure conditions. Often overlooked is the fact that microplastics are dynamic contaminants, changing over time through degradation and fragmentation and subsequently exhibiting altered surface chemistry, notably an increased presence and diversity of functional groups. The same functional groups characterized on microplastics are also present in dissolved organic matter, often termed dissolved organic carbon (DOC), a class of substances for which we have a far greater understanding of their ionoregulatory actions. We highlight instances in which the effects of microplastic exposure resemble those of DOC exposure. We propose that in future microplastic investigations, in vivo techniques that have proven useful in understanding the ionoregulatory effects of DOC should be used including measurements of transepithelial potential, net and unidirectional radio-isotopic ion flux rates, and concentration kinetic analyses of uptake transport. More sophisticated in vitro approaches using cultured gill epithelia, Ussing chamber experiments on gill surrogate membranes, and scanning ion selective electrode techniques (SIET) may also prove useful. Finally, in future studies we advocate for minimum reporting requirements of microplastic properties and experimental conditions to help advance this important emerging field.

Enhancing Lithium-Ion Diffusion Kinetics in a 3D Lithium Metal Host through Surface Modification with Hierarchical Multimetal Oxides.

Lithium metal is a promising anode candidate to achieve high-energy-density lithium metal batteries (LMBs) due to its ultrahigh theoretical capacity (3860 mA h g-1) and low electrochemical potential (-3.04 V vs S.H.E). Unfortunately, the commercialization of lithium metal anodes is hindered by the growth of Li dendrites and the infinite Li volume changes during the cycling process. Herein, we introduce a 3D hierarchical multimetal oxide nanowire framework as a current collector for Li metal anodes. The hierarchical metal oxide layers of CoO and CuxO provide abundant Li nucleation sites and thus offer uniform Li plating and regulate Li nucleation during the charge/discharge process. As a result, half cells present a prolonging Coulombic efficiency of 97% at 1 mA cm-2 with a capacity of 1 mA h cm-2 for over 300 cycles. A stable cyclability of symmetric cells is demonstrated under 1 mA cm-2 with a capacity of 1 mA h cm-2 for 1500 h. Full cells paired with an LFP cathode show a stable capacity of 131.5 mA h g-1 with a capacity retention of 92% for 200 cycles. These results will shed insights into the design of 3D Cu current collectors for high-performance composite Li metal anodes.

Intricate Ionic Behaviors in High-Performance Self-Powered Hydrothermal Chemical Generator Using Water and Iron (III) Gate.

Utilizing the ionic flux to generate voltage output has been confirmed as an effective way to meet the requirements of clean energy sources. Different from ionic thermoelectric (i-TE) and hydrovoltaic devices, a new hydrothermal chemical generator is designed by amorphous FeCl3 particles dispersing in MWCNT and unique ferric chloride or water gate. In the presence of gate, the special ion behaviors enable the cell to present a constant voltage of 0.60 V lasting for over 96 h without temperature difference. Combining the differences of cation concentration, humidity and temperature between the right and left side of sample, the maximum short-circuit current and power output can be obtained to 168.46 µA and 28.11 µW, respectively. The generator also can utilize the low-grade heat to produce electricity wherein Seebeck coefficient is 6.79 mV K-1. The emerged hydrothermal chemical generator offers a novel approach to utilize the low-grade heat, water and salt solution resources, which provides a simple, sustainable and low-cost strategy to realize energy supply.

Covalent Organic Framework with 3D Ordered Channel and Multi-Functional Groups Endows Zn Anode with Superior Stability.

Achieving a highly robust zinc (Zn) metal anode is extremely important for improving the performance of aqueous Zn-ion batteries (AZIBs) for advancing "carbon neutrality" society, which is hampered by the uncontrollable growth of Zn dendrite and severe side reactions including hydrogen evolution reaction, corrosion, and passivation, etc. Herein, an interlayer containing fluorinated zincophilic covalent organic framework with sulfonic acid groups (COF-S-F) is developed on Zn metal (Zn@COF-S-F) as the artificial solid electrolyte interface (SEI). Sulfonic acid group (- SO3H) in COF-S-F can effectively ameliorate the desolvation process of hydrated Zn ions, and the three-dimensional channel with fluoride group (-F) can provide interconnected channels for the favorable transport of Zn ions with ion-confinement effects, endowing Zn@COF-S-F with dendrite-free morphology and suppressed side reactions. Consequently, Zn@COF-S-F symmetric cell can stably cycle for 1,000 h with low average hysteresis voltage (50.5 mV) at the current density of 1.5 mA cm-2. Zn@COF-S-F|MnO2 cell delivers the discharge specific capacity of 206.8 mAh g-1 at the current density of 1.2 A g-1 after 800 cycles with high-capacity retention (87.9%). Enlightening, building artificial SEI on metallic Zn surface with targeted design has been proved as the effective strategy to foster the practical application of high-performance AZIBs.

Uniform Li Deposition through the Graphene-Based Ion-Flux Regulator for High-Rate Li Metal Batteries.

Lithium (Li) metal is considered an ultimate anode owing to its high specific capacity and energy density. However, uncontrolled Li dendrite growth and low Coulombic efficiency have limited the application of Li metal. Among various strategies introduced to address these limitations, the surface modification of polyolefin separators with functional materials has been widely adopted for improving the mechanical and thermal stabilities of polymer separators and to protect the separator from the penetration of Li dendrites. Herein, we report a new functional polymer separator that is surface-altered with a graphene-based Li-ion flux regulator (GLR) to homogenize the Li-ion flux and suppress the growth of sharp dendritic Li in Li metal batteries. The nanopores distributed through the GLR structure serve as channels for ion transport and junctions for electron transfer, facilitating efficient electrolyte penetration and rapid charge transfer between graphene (Gr) sheets. Owing to these favorable features of porous GLR, a Li-Cu cell with the GLR surface-altered polypropylene separator (GLR-PP) delivers excellent cycle and rate performances compared to a Li-Cu cell with a Gr surface-altered polypropylene separator. In addition, among the tested cells, Li-sulfur cells with GLR-PP exhibit the most stable cycle performance over 500 cycles. These results demonstrate that the concept of tailoring the surface of a polymer separator with porous 2D materials is an effective strategy for improving the long-term cycle stability and electrochemical kinetics of Li metal-based batteries and would trigger further relevant studies.

Dynamic modulation of transthylakoid electric potential by chloroplast ATP synthases.

The light-induced transthylakoid membrane potential (ΔΨm) can function as a driving force to help catalyzing the formation of ATP molecules, proving a tight connection between ΔΨm and the ATP synthase. Naturally, a question can be raised on the effects of altered functioning of ATP synthases on regulating ΔΨm, which is attractive in the area of photosynthetic research. Lots of findings, when making efforts of solving this difficulty, can offer an in-depth understanding into the mechanism behind. However, the functional network on modulating ΔΨm is highly interdependent. It is difficult to comprehend the consequences of altered activity of ATP synthases on adjusting ΔΨm because parameters that have influences on ΔΨm would themselves be affected by ΔΨm. In this work, a computer model was applied to check the kinetic changes in polarization/depolarization across the thylakoid membrane (TM) regulated by the modified action of ATP synthases. The computing data revealed that under the extreme condition by numerically "switching off" the action of the ATP synthase, the complete inactivation of ATP synthase would markedly impede proton translocation at the cytb6f complex. Concurrently, the KEA3 (CLCe) porter, actively pumping protons into the stroma, further contributes to achieving a sustained low level of ΔΨm. Besides, the quantitative consequences on every particular component of ΔΨm adjusted by the modified functioning of ATP synthases were also explored. By employing the model, we bring evidence from the theoretical perspective that the ATP synthase is a key factor in forming a transmembrane proton loop thereby maintaining a propriate steady-state ΔΨm to meet variable environmental conditions.

Coregulation of Li/Li+ Spatial Distribution by Electric Field Gradient with Homogenized Li-Ion Flux for Dendrite-Free Li Metal Anodes.

Lithium (Li) metal batteries are highly sought after for their exceptional energy density. However, their practical implementation is impeded by the formation of dendrites and significant volume fluctuations in Li, which stem from the uneven distribution of Li-ions and uncontrolled deposition of Li on the current collector. Here, an amino-functionalized reduced graphene oxide covered with polyacrylonitrile (PrGN) film with an electric field gradient structure is prepared to deal with such difficulties. This novel current collector serves to stabilize Li-metal anodes by regulating Li-ion flux through vertically aligned channels formed by porous polyacrylonitrile (PAN). Moreover, the amino-functionalized reduced graphene oxide (rGN) acts as a three-dimensional (3D) host, reducing nucleation overpotential and accommodating volume expansion during cycling. The combination of the insulating PAN and conducting rGN creates an electric field gradient that promotes a bottom-up mode of Li electrodeposition and safeguards the anode from interfacial parasitic reactions. Consequently, the electrodes exhibit exceptional cycle life with stable voltage profiles and minimal hysteresis under high current densities and large areal capacities.

Structural, developmental and functional analyses of leaf salt glands of mangrove recretohalophyte Aegiceras corniculatum.

Salt secretion is an important strategy used by the mangrove plant Aegiceras corniculatum to adapt to the coastal intertidal environment. However, the structural, developmental and functional analyses on the leaf salt glands, particularly the salt secretion mechanism, are not well documented. In this study, we investigated the structural, developmental and degenerative characteristics and the salt secretion mechanisms of salt glands to further elucidate the mechanisms of salt tolerance of A. corniculatum. The results showed that the salt gland cells have a large number of mitochondria and vesicles, and plenty of plasmodesmata as well, while chloroplasts were found in the collecting cells. The salt glands developed early and began to differentiate at the leaf primordium stage. We observed and defined three stages of salt gland degradation for the first time in A. corniculatum, where the secretory cells gradually twisted and wrinkled inward and collapsed downward as the salt gland degeneration increased and the intensity of salt gland autofluorescence gradually diminished. In addition, we found that the salt secretion rate of the salt glands increased when the treated concentration of NaCl increased, reaching the maximum at 400 mM NaCl. The salt-secreting capacity of the salt glands of the adaxial epidermis is significantly greater than that of the abaxial epidermis. The real-time quantitative PCR results indicate that SAD2, TTG1, GL2 and RBR1 may be involved in regulating the development of the salt glands of A. corniculatum. Moreover, Na+/H+ antiporter, H+-ATPase, K+ channel and Cl- channel may play important roles in the salt secretion of salt glands. In sum mary, this study strengthens the understanding of the structural, developmental and degenerative patterns of salt glands and salt secretion mechanisms in mangrove recretohalophyte A. corniculatum, providing an important reference for further studies at the molecular level.

Important Role of Ion Flux Regulated by Separators in Lithium Metal Batteries.

Polyolefin separators are the most common separators used in rechargeable lithium (Li)-ion batteries. However, the influence of different polyolefin separators on the performance of Li metal batteries (LMBs) has not been well studied. By performing particle injection simulations on the reconstructed three-dimensional pores of different polyethylene separators, it is revealed that the pore structure of the separator has a significant impact on the ion flux distribution, the Li deposition behavior, and consequently, the cycle life of LMBs. It is also discovered that the homogeneity factor of Li-ion toward Li metal electrode is positively correlated to the longevity and reproducibility of LMBs. This work not only emphasizes the importance of the pore structure of polyolefin separators but also provides an economic and effective method to screen favorable separators for LMBs.

Enhancement of Ar Ion Flux on the Substrate by Heterogeneous Charge Transfer Collision of Ar Atom with He Ion in an Inductively Coupled Ar/He Plasma.

The understanding of ion dynamics in plasma applications has received significant attention. In this study, we examined these effects between He and Ar species, focusing on the Ar ion flux on the substrate. To control heterogeneous collisions, we varied the He addition rate at fixed chamber pressure and the chamber pressure at fixed Ar/He ratio in an inductively coupled Ar/He plasma source. Throughout the experiments, we maintained an electron density in the bulk plasma and plasma potential as a constant value by adjusting the RF power and applying an additional DC bias to eliminate any disturbances caused by the plasma. Our findings revealed that the addition of He enhances the Ar ion flux, despite a decrease in the Ar ion density at the plasma-sheath boundary due to the presence of He ions. Moreover, we found that this enhancement becomes more prominent with increasing pressure at a fixed He addition rate. These results suggest that the heterogeneous charge transfer collision between Ar atoms and He ions in the sheath region creates additional Ar ions, ultimately leading to an increased Ar ion flux on the substrate. This finding highlights the potential of utilizing heterogeneous charge transfer collisions to enhance ion flux in plasma processing, without the employment of additional equipment.

Ion fluxes Involved in the Adaptation of the Estuarine Diatom Coscinodiscus centralis Ehrenberg to Salinity Stress.

Although estuarine diatoms have a wide range of salt tolerance, they are often severely stressed by elevated salt concentrations. It remains poorly understood how estuarine diatoms maintain ionic homeostasis under high-salinity conditions. Using a scanning ion-selective electrode technique, this study determined the fluxes of H+, Na+, and K+ involved in the acclimatization of the estuarine diatom Coscinodiscus centralis Ehrenberg after an elevation in salinity from 15 psu to 35 psu. The C. centralis cells exhibited marked H+ effluxes after a transient treatment (TT, 30 min) and short-term treatment (ST, 24 h). However, a drastic shift of H+ efflux toward an influx was induced in the long-term treatment (LT, 10 days). The Na+ flux under TT, ST, and LT salinity conditions was found to accelerate the Na+ efflux. More pronounced effects were observed under the ST and LT salinity conditions compared to the TT salinity condition. The K+ influx showed a significant increase under the LT salinity condition. However, the salinity-induced Na+/H+ exchange in the estuarine diatom was inhibited by amiloride and sodium orthovanadate. These results indicate that the Na+ extrusion in salt-stressed cells is mainly the result of an active Na+/H+ antiport across the plasma membrane. The pattern of ion fluxes under the TT and ST salinity conditions were different from those under the LT salinity conditions, suggesting an incomplete regulation of the acclimation process in the estuarine diatom under short-term salinity stress.

Simultaneous Inhibition of Zn Dendrites and Polyiodide Ions Shuttle Effect by an Anion Concentrated Electrolyte Membrane for Long Lifespan Aqueous Zinc-Iodine Batteries.

Aqueous zinc-iodine (Zn-I2) batteries have attracted extensive attention due to their merits of inherent safety, wide natural abundance, and low cost. However, their application is seriously hindered by the irreversible capacity loss resulting from both anode and cathode. Herein, an anion concentrated electrolyte (ACE) membrane is designed to manipulate the Zn2+ ion flux on the zinc anode side and restrain the shuttle effect of polyiodide ions on the I2 cathode side simultaneously to realize long-lifetime separator-free Zn-I2 batteries. The ACE membrane with abundant sulfonic acid groups possesses a multifunctional amalgamation of good mechanical strength, guided Zn2+ ion transport, and effective charge repulsion of polyiodide ions. Moreover, rich ether oxygen, carbonyl, and S-O bonds in anionic polymer chains will form hydrogen bonds with water to reduce the proportion of free water in the ACE membrane, inhibiting the water-induced interfacial side reactions of the Zn metal anode. Besides, DFT calculations and in-situ UV-vis and in situ Raman results reveal that the shuttle effect of polyiodide ions is also significantly suppressed. Therefore, the ACE membrane enables a long lifespan of Zn anodes (3700 h) and excellent cycling stability of Zn-I2 batteries (10000 cycles), thus establishing a substantial base for their practical applications.

A new method for assessment of electro-osmotic permeability through the integration of theoretical and experimental ion flux in electrokinetic processes.

Electrokinetic (EK) technology is promising for removing heavy metals from contaminated unsaturated soils. It is crucial to accurately determine the unsaturated electro-osmotic permeability for predicting the efficiency of EK treatment, optimizing treatment strategies, and accurately predicting the distribution of contaminant concentrations. However, the current approach of estimating unsaturated electro-osmotic permeability, which involves measuring effective voltage, drainage volume, and performing exponential fitting, fails to address the issue of uneven voltage gradient distribution during EK treatment. Herein, a novel method was presented for estimating the electro-osmotic permeability of unsaturated porous media. This method quantifies the electro-osmotic flow in an unsaturated porous medium by considering the difference in mass-transfer efficiency (MTE) between real (with electro-osmotic flow) and hypothetical cases (without electro-osmotic flow). This difference serves as a metric for estimating the electro-osmotic permeability. Results revealed a linear relationship between the electro-osmotic permeability and the product of volumetric moisture content and tortuosity, with the slope related to the ionic mobility of target ions, hypothetical and actual MTE. To validate this method, hexavalent Cr (Cr(VI)) was selected as the target contaminant and six EK experiments were conducted with varying initial volumetric moisture content. The feasibility of the method was evaluated by fitting the results of these experiments to obtain the specific slope of the porous medium used. Compared to the existing effective voltage-drainage volume-exponential fitting method, the proposed method offers several advantages. First, it effectively addressed the issue of nonuniform voltage distribution during EK treatment in the unsaturated porous medium. Second, it overcame the problem of a nonzero electro-osmotic permeability at zero volumetric moisture content in the exponential empirical formula. Third, the proposed method was based on theoretical derivations instead of relying solely on empirical fitting. Finally, the proposed method does not require a prior estimate of the saturated electro-osmotic permeability of the porous medium.

Contribution of Ion Energy and Flux on High-Aspect Ratio SiO2 Etching Characteristics in a Dual-Frequency Capacitively Coupled Ar/C4F8 Plasma: Individual Ion Energy and Flux Controlled.

As the process complexity has been increased to overcome challenges in plasma etching, individual control of internal plasma parameters for process optimization has attracted attention. This study investigated the individual contribution of internal parameters, the ion energy and flux, on high-aspect ratio SiO2 etching characteristics for various trench widths in a dual-frequency capacitively coupled plasma system with Ar/C4F8 gases. We established an individual control window of ion flux and energy by adjusting dual-frequency power sources and measuring the electron density and self-bias voltage. We separately varied the ion flux and energy with the same ratio from the reference condition and found that the increase in ion energy shows higher etching rate enhancement than that in the ion flux with the same increase ratio in a 200 nm pattern width. Based on a volume-averaged plasma model analysis, the weak contribution of the ion flux results from the increase in heavy radicals, which is inevitably accompanied with the increase in the ion flux and forms a fluorocarbon film, preventing etching. At the 60 nm pattern width, the etching stops at the reference condition and it remains despite increasing ion energy, which implies the surface charging-induced etching stops. The etching, however, slightly increased with the increasing ion flux from the reference condition, revealing the surface charge removal accompanied with conducting fluorocarbon film formation by heavy radicals. In addition, the entrance width of an amorphous carbon layer (ACL) mask enlarges with increasing ion energy, whereas it relatively remains constant with that of ion energy. These findings can be utilized to optimize the SiO2 etching process in high-aspect ratio etching applications.

Uptake of TiO2 Nanoparticles was Linked to Variation in net Cation flux in Wheat Seedlings.

Titanium dioxide nanoparticles (TiO2 NPs) are ubiquitous in the environment and enter the terrestrial food chain via plant uptake. However, plant uptake behaviors of TiO2 NPs remain elusive. Here, the uptake kinetics of TiO2 NPs by wheat (Triticum aestivum L.) seedlings and the effects on cation flux in roots were examined in a hydroponic system. Uptake rate of TiO2 NPs ranged from 119.0 to 604.2 mg kg- 1 h- 1 within 8 h exposure. NP uptake decreased by 83% and 47%, respectively, in the presence of sodium azide (NaN3) and carbonyl cyanide m-chlorophenylhydrazone (CCCP), indicating an energy-dependent uptake of TiO2 NPs. Moreover, accompanied with TiO2 NP uptake, net influx of Cd2+ decreased by 81%, while Na+ flux shifted from inflow to outflow at the meristematic zone of root. These findings provide valuable information for understanding plant uptake of TiO2 NPs.