Evaluation of particle and volatile organic compound emissions during the use of 3D pens.

This study investigated particle and volatile organic compound (VOC) emission rates (ER) from 3D pens, which are increasingly popular in children's toys. Nine filaments and two 3D pens were evaluated using a flow tunnel, a scanning mobility particle sizer, a proton-transfer-reaction time-of-flight mass spectrometer for particles, and a thermal desorption-gas chromatography-mass spectrometer for VOCs. Results showed that the ERs varied with the pen type, filament, and brand. The particle ER was highest for acrylonitrile butadiene styrene (ABS), followed by polylactic acid (PLA) and polycaprolactone (PCL). Notably, ERs of 83 % and 33 % of ABS and PLA filaments exceeded the maximum allowable particle ER (MAER; 5 × 109 particles/min) for 3D printers but were lower than the VOC MAER (173 µg/min in the office). Different filaments emitted diverse VOCs; ABS emitted styrene and benzene, PLA emitted lactide, and PCL emitted phenol. While particle ERs from 3D pens were comparable to those from printers, the total VOC ERs from 3D pens were slightly lower. Caution is warranted when using 3D pens because of potential health risks, especially their prolonged use, proximity to the breathing zone, and usage by children. This study highlights the need for considering particles and VOCs when assessing the safety of 3D pens, emphasizing awareness of potential hazards, particularly in child-oriented settings.

Polyester microfiber impacts on coastal sediment organic matter consumption.

As plastic pollution continues to accumulate at the seafloor, concerns around benthic ecosystem functionality heightens. This research demonstrates the systematic effects of polyester microfibers on seafloor organic matter consumption rates, an important benthic ecosystem function connected to multiple reactions and processes. We used a field-based assay to measure the loss of organic matter, both with and without polyester microfiber contamination. We identified sediment organic matter content, mud content, and mean grain size as the main drivers of organic matter consumption, however, polyester microfiber contamination decoupled ecosystem relationships and altered observed organic matter cycling dynamics. Organic matter consumption rates varied across horizontal and vertical spaces, highlighting that consumption and associated plastic effects are dependent on environmental heterogeneity at both small (within sites) and larger (between sites) scales. Our results emphasize the important role habitat heterogeneity plays in seafloor organic matter consumption and the associated effects of plastic pollution on ecosystem function.

The metabolism of membrane lipid participates in the occurrence of chilling injury in cold-stored banana fruit.

Banana fruit is highly vulnerable to chilling injury (CI) during cold storage, which results in quality deterioration and commodity reduction. The purpose of this study was to investigate the membrane lipid metabolism mechanism underlying low temperature-induced CI in banana fruit. Chilling temperature significantly induced CI symptoms in banana fruit, compared to control temperature (22 °C). Using physiological experiments and transcriptomic analyses, we found that chilling temperature (7 °C) increased CI index, malondialdehyde content, and cell membrane permeability. Additionally, chilling temperature upregulated the genes encoding membrane lipid-degrading enzymes, such as lipoxygenase (LOX), phospholipase D (PLD), phospholipase C (PLC), phospholipase A (PLA), and lipase, but downregulated the genes encoding fatty acid desaturase (FAD). Moreover, chilling temperature raised the activities of LOX, PLD, PLC, PLA, and lipase, inhibited FAD activity, lowered contents of unsaturated fatty acids (USFAs) (γ-linolenic acid and linoleic acid), phosphatidylcholine, and phosphatidylinositol, but retained higher contents of saturated fatty acids (SFAs) (stearic acid and palmitic acid), free fatty acids, phosphatidic acid, lysophosphatidic acid, diacylglycerol, a lower USFAs index, and a lower ratio of USFAs to SFAs. Together, these results revealed that chilling temperature-induced chilling injury of bananas were caused by membrane integrity damage and were associated with the enzymatic and genetic manipulation of membrane lipid metabolism. These activities promoted the degradation of membrane phospholipids and USFAs in fresh bananas during cold storage.

Determination of disperse dyes on polyester fibers by UHPLC-Orbitrap MS.

The determination of fiber dyes is important in forensic investigations. Although a variety of fiber dyes detection methods have been established, the sensitive and accurate determination of trace fiber dyes remains a challenge due to the possible interferences caused by complex environmental matrix and various fiber additives. Orbitrap mass spectrometry (Orbitrap MS) is a type of high-resolution mass spectrometry with high qualitative accuracy and detection sensitivity which highly meet the identification requirements of fiber dyes in real cases. However, the application of Orbitrap MS in fiber dye analysis is limited. In this regard, this study used polyester fiber, which is the most commonly-found fiber in forensic cases, as a model and established a UHPLC-Orbitrap MS method to analyze disperse dyes on polyester fibers. Using the optimized UHPLC-Orbitrap MS method, nine disperse dyes were accurately identified and well separated, and the limits of detection ranged between 0.1 ng/mL and 5.0 ng/mL. The developed method was applied to analyze actual fiber samples, and dyes from single fibers of 1 mm in length could be accurately detected. The established method is sensitive, accurate, and demonstrates good application prospects.

Application of electrospun composite nanofibers as an efficient sorbent for extraction of pesticides from food samples.

Herein, the composite of polylactic acid (PLA)/ Iron-based metal-organic framework (r-MIL-88A)/ Cellulose electrospun nanofibers was fabricated; and then, applied as a novel sorbent for thin-film micro-extraction (TFME) of four selected pesticides followed by GC-FID analysis. From the evaluation of scanning electron microscopy, Fourier transform infrared spectroscopy energy dispersive X-ray spectroscopy and X-ray diffraction, the successful fabrication of composite nanaofibers was approved. The presence of r-MIL-88A/Cellulose with large surface area and plenty of OH-functional groups results in improving PLA extraction efficiency. The effect of various main parameters on extraction efficiency was evaluated. The LODs (based on S/N = 3) were in the range of 1.0 to 1.5 ng mL-1. Intra-day and inter-day relative standard deviations (RSDs) were in the range of 4.8% - 5.6% and 5.2%-6.4%, respectively. In addition, the fiber to fiber relative standard deviations were observed in the range of 5.2%-12.3%. By using the optimized factors, acceptable linearity ranges were obtained in the range of 3.0-1900.0 ng mL-1 for metribuzin and ethofumasate, and 5.0-2000.0 for atrazine and ametryn (R2 = 0.9913-0.9967). The developed method was investigated in fruit juice, vegetables, milk and honey samples, and recoveries (79.3-95.6%) indicate that the PLA/r-MIL-88A/Cellulose can be a prominent composite film for the extraction of the target analytes in various samples.

Additives in polypropylene and polylactic acid food packaging: Chemical analysis and bioassays provide complementary tools for risk assessment.

Plastic food packaging represents 40 % of the plastic production worldwide and belongs to the 10 most commonly found items in aquatic environments. They are characterized by high additives contents with >4000 formulations available on the market. Thus they can release their constitutive chemicals (i.e. additives) into the surrounding environment, contributing to chemical pollution in aquatic systems and to contamination of marine organism up to the point of questioning the health of the consumer. In this context, the chemical and toxicological profiles of two types of polypropylene (PP) and polylactic acid (PLA) food packaging were investigated, using in vitro bioassays and target gas chromatography mass spectrometry analyses. Plastic additives quantification was performed both on the raw materials, and on the material leachates after 5 days of lixiviation in filtered natural seawater. The results showed that all samples (raw materials and leachates) contained additive compounds (e.g. phthalates plasticizers, phosphorous flame retardants, antioxidants and UV-stabilizers). Differences in the number and concentration of additives between polymers and suppliers were also pointed out, indicating that the chemical signature cannot be generalized to a polymer and is rather product dependent. Nevertheless, no significant toxic effects was observed upon exposure to the leachates in two short-term bioassays targeting baseline toxicity (Microtox® test) and Pacific oyster Crassostrea gigas fertilization success and embryo-larval development. Overall, this study demonstrates that both petrochemical and bio-based food containers contain harmful additives and that it is not possible to predict material toxicity solely based on chemical analysis. Additionally, it highlights the complexity to assess and comprehend the additive content of plastic packaging due to the variability of their composition, suggesting that more transparency in polymer formulations is required to properly address the risk associated with such materials during their use and end of life.

Neural networks and genetic algorithm as robust optimization tools for modeling the microbial production of poly-ß-hydroxybutyrate (PHB) from Brewers' spent grain.

This research work has been carried out to establish the combinatorial impact of various fermentation medium constituents, used for poly-ß hydroxybutyrate (PHB) biosynthesis. Model development was performed with an optimized medium composition that enhanced the biosynthesis of PHB from the biowaste material Brewers' spent grain (BSG). The latter was used as a carbon substrate in submerged fermentation with Bacillus sphaericus NCIM 2478. Three independent variables: BSG, yeast extract (YE), and salt solution concentration (SS) and one dependent variable (amount of PHB produced) were assigned. A total of 35 microbial fermentation trials were conducted by which a nonlinear mathematical relationship was established in terms of neural network model between independent and dependent variables. The resulting artificial neural networks (ANNs) model for this process was further optimized using a global genetic algorithm optimization technique, which predicted the maximum production of PHB (916.31 mg/L) at a concentration of BSG (50.12 g/L), concentration of YE (0.22 g/L), and concentration of SS (24.06%, v/v). The experimental value of the quantity of PHB (concentration ∼916 mg/L) was found to be very close to the value predicted by the ANN-GA model approach.

Historical and current occurrence of microplastics in water and sediment of a Finnish lake affected by WWTP effluents.

Only scarce information is available about the abundance of microplastics (MPs) in Nordic lakes. In this study, the occurrence, types, and distribution of MPs were assessed based on the lake water and sediment samples collected from a sub-basin of Lake Saimaa, Finland. The main goal was to estimate the possible effect of the local wastewater treatment plant (WWTP) on the abundance of MPs in different compartments of the recipient lake area. Collected bottom sediment samples were Cs-137 dated and the chronological structure was utilized to relate the concentrations of MPs to their sedimentation years. Raman microspectroscopy was used for the MPs' identification from both sample matrices. In addition, MPs consisting of polyethylene (PE), polypropylene (PP) and polystyrene (PS) were quantified from lake water samples by pyrolysis-gas chromatography-mass spectrometry to provide a complementary assessment of MPs based on two different analysis methods, which provide different metrics of the abundance of microplastics. MPs concentrations were highest in sediment samples closest to the discharge site of WWTP effluents (4400 ± 620 n/kg dw) compared to other sites. However, such a trend was not found in lake water samples (0.7 ± 0.1 n/L). Overall, microplastic fibers were relatively more abundant in sediment (70%) than in water (40%), and the majority of detected microplastic fibers were identified as polyester. This indicates that a part of textile fibers passing the WWTP processes accumulate in the sediment close to the discharge site. In addition, the abundance of MPs was revealed to have increased slightly during the last 30 years.

Migration of Microplastics and Phthalates from Face Masks to Water.

Since the outbreak of COVID-19, face masks have been introduced in the complex strategy of infection prevention and control. Face masks consist of plastic polymers and additives such as phthalates. The aim of this study was to evaluate the migration of microplastics (MP) and phthalates from face masks to water. Four types of masks including FFP2 masks and surgical were studied. Masks were first characterized to determine the different layers and the material used for their fabrication. Then, masks were cut into 20 pieces of 0.5 cm2, including all their layers, placed in water, and the migration of MP and phthalates was evaluated according to the conditions stated in EU Regulation No 10/2011 on plastic materials and articles intended to come into contact with food. For MP, the morphological analysis (shape, dimension, particle count) was performed using a stereomicroscope, while the identification of both masks and MP released was conducted using µ-Fourier-transform infrared spectroscopy (µ-FT-IR). Migration of phthalates was assessed by ultra-high-performance liquid chromatography coupled to triple quadrupole mass spectrometer (UPLC-MS/MS). Face masks analyzed in the present study were made of atactic polypropylene (PP) as stated by the manufacturer. The µ-FT-IR confirmed that PP and polyamide (PA) were released as fragments, while both PP and polyester (PES) were released as fibers. In addition, 4 phthalates were identified at concentrations between 2.34 and 21.0 µg/mask. This study shows that the migration study can be applied to evaluate the potential release of MP and phthalates from face masks to water and could give a hint for the potential impact of their incorrect disposal on the aquatic resources.

Low sensitivity of Pinus mugo to surface ozone pollution in the subalpine zone of continental Europe.

High altitudes have been exposed to enhanced levels of surface ozone (O3) concentrations over recent decades compared to the pre-industrial era. The responses of vegetation to this toxic pollutant are species-specific and depend on the climate conditions. In this paper, we explored the reaction of Pinus mugo (P. mugo) to O3-induced stress in the continental climate of an ozone-rich mountain area in the High Tatra Mountains (Western Carpathians). The effects of O3 doses modelled by a deposition model, O3 concentrations and other factors on P. mugo were identified from (a) satellite-based data via NDVI (normalised differenced vegetation index) over 2000-2020 and (b) visible injury on needle samples gathered from P. mugo individuals at ground-truth sites in 2019 and 2020. Analysing the NDVI trend, we observed non-significant changes (p > 0.05) in the greenness of P. mugo despite growing in an environment with the average seasonal O3 concentration around 51.6 ppbv, the maximum hourly concentrations more than 90 ppbv and increasing trend of O3 doses by 0.1 mmol m-2 PLA (plant leaf area) year-1. The visible O3 injury of samples collected at study sites was low (mean injury observed on 1-10% of needles' surface), and the symptoms of injury caused by other biotic and abiotic factors prevailed over those caused by O3. In addition, the correlation analyses between NDVI and the climatic factors indicated a significant (p < 0.05) and positive relationship with photosynthetic active radiation (R = 0.45) in July, and with stomatal conductance (R = 0.52) and temperature factor (R = 0.43) in August. Therefore, we concluded that the positive effect of climate conditions, which support the growth processes of P. mugo, may suppress the negative effect of the mean O3 doses of 17.8 mmol m-2 PLA accumulated over the growing season.

Synergistic effect of microcrystalline cellulose from oil palm empty fruit bunch waste and tricresyl phosphate on the properties of polylactide composites.

Microcrystalline cellulose (MCC) was extracted from oil palm empty fruit bunch (OPEFB) waste by integrated chemical treatments of delignification, bleaching, and acidic hydrolysis. The obtained MCC (OPMC) and tricresyl phosphate (TCP) were used as additives for polylactide (PLA) composites. The influences of OPMC and TCP contents, separately and in combination, were evaluated on the properties of the composites. Characterization studies confirmed the successful extraction of OPMC from OPEFB waste. With regard to the properties of the PLA composite, the appropriate content of OPMC should be 5 phr. The good distribution of OPMC in the polymer matrix changed the failure behavior of the composite from brittle to ductile. All the PLA composites with TCP and OPMC showed flame inhibition and retarded ignition. The synergistic effect of TCP and OPMC resulted in outstanding improvement of impact strength and flame retardancy of composites. The impact toughness of PT10M5 increased to about 218.4 % and 72.3 % that of neat PLA and PT0M5, respectively. Moreover, PT10M5 achieved V-0 rating with high LOI (38.5 %). All these characteristics promise extended applications for PLA composite in bio, circular, and green (BCG) economies and electronics industries.

Liquid chromatography-mass spectrometry method for the determination of polyethylene terephthalate and polybutylene terephthalate cyclic oligomers in blood samples.

Food contact materials (FCM) polyethylene terephthalate (PET) and polybutylene terephthalate (PBT) used extensively in food packaging may contain cyclic oligomers which may migrate into food and thus cause toxic effects on human health. A simple, fast, and sensitive ultra-high-performance liquid chromatography method quadrupole time-of-flight mass spectrometer was developed for the analysis of 7 cyclic oligomers in post-mortem blood samples. The targeted analytes were separated on a Waters BEH C18 (150 × 2.1 mm, 1.7 µm) analytical column by gradient elution. Calibration curves were constructed based on standard solutions and blood samples and Student's t-test was applied to evaluate the matrix effect. The LODs ranged from 1.7 to 16.7 µg mL-1, while the method accuracy was assessed by recovery experiments and resulting within the range 84.2-114.6%. Such an analytical method for the determination of PET and PBT cyclic oligomers in biological samples is reported for the first time. The developed methodology allows the determination of these oligomers in blood providing a useful analytical tool to assess the exposure and thus the potential hazard and health risks associated with these non-intentionally added substances (NIAS) from PET and PBT FCM through food consumption. The method was validated and successfully applied to the analysis of 34 post-mortem whole blood samples. Polyethylene terephthalate trimer was detected in four of them, for the first time in literature.

Comparison of LC-ESI, DART, and ASAP for the analysis of oligomers migration from biopolymer food packaging materials in food (simulants).

Biopolymers based on polylactic acid (PLA) and starch have numerous advantages, such as coming from renewable sources or being compostable, though they can have deficiencies in mechanical properties, and for this reason, polyester resins are occasionally added to them in order to improve their properties. In this work, migration from a PLA sample and from another starch-based biopolymer to three different food simulants was studied. Attention was focused on the determination of oligomers. The analysis was first performed by ultraperformance liquid chromatography quadrupole-time-of-flight mass spectrometry (UPLC-Q-TOF-MS), which allowed the identification of the oligomers present in migration. Then, the samples were analyzed by two ambient desorption/ionization techniques directly coupled to mass spectrometry (ADI), direct analysis in real-time coupled to standardized voltage and pressure (DART-MS) and atmospheric pressure solids analysis probe (ASAP-MS). These methodologies were able to detect simultaneously the main oligomers migrants and their adducts in a very rapid and effective way. Nineteen different polyester oligomers, fourteen linear and five cyclic, composed of different combinations of adipic acid [AA], propylene glycol [PG], dipropylene glycol [DPG], 2,2-dibutyl-1,3-propanediol [DBPG], or isobutanol [i-BuOH] were detected in migration samples from PLA. In migration samples from starch-based biopolymer, fourteen oligomers from poly(butylene adipate co-terephthalate) polyester (PBAT) were identified, twelve cyclic and two linear. The results from ADI techniques showed that they are a very promising alternative tool to assess the safety and legal compliance of food packaging materials.

Production of eco-friendly PHB-based bioplastics by Pseudomonas aeruginosa CWS2020 isolate using poultry (chicken feather) waste.

Nowadays, the accumulation of non-degradable plastics and other disposed wastes leads to environmental pollution across the world. The production of eco-friendly and cost-effective poly-ß-hydroxybutyrate (PHB) could be a better alternative to conventional petroleum-based plastics and prevent environmental pollution. Besides, the area in and around Namakkal, Tamil Nadu, India is well known for poultries, currently facing the number of environmental issues due to the accumulation of chicken feather waste. This study focused on the production of eco-friendly PHB by recycling poultry (chicken feather) waste as the substrate. The native PHB producers were screened from the chicken waste disposal site in Namakkal by Sudan black B staining method. Further, the potent bacterial isolate was identified as Pseudomonas aeruginosa (NCBI accession MF18889) by phenotypic and genotypic characteristics. The PHB production media with chicken feather waste was statistically optimized by response surface methodology. The dry weight of PHB produced under optimized condition (15.96 g/L chicken feather waste, 37 °C temperature, 19.8 g/L glucose and 6.85 pH) was found to be 4.8 g/L. Besides, PHB was characterized and confirmed by thin-layer chromatography, Fourier-transform infrared spectroscopy and Gas chromatography-mass spectrometry analysis. Thus, this study concludes that poultry waste could be a complex nitrogen source for improving the growth of PHB producers and substantially increasing the yield of PHB, and it will be an eco-friendly and low-cost production in bioprocess technology.

Effects of Water and Chemical Solutions Ageing on the Physical, Mechanical, Thermal and Flammability Properties of Natural Fibre-Reinforced Thermoplastic Composites.

Biocomposites comprising a combination of natural fibres and bio-based polymers are good alternatives to those produced from synthetic components in terms of sustainability and environmental issues. However, it is well known that water or aqueous chemical solutions affect natural polymers/fibres more than the respective synthetic components. In this study the effects of water, salt water, acidic and alkali solutions ageing on water uptake, mechanical properties and flammability of natural fibre-reinforced polypropylene (PP) and poly(lactic acid) (PLA) composites were compared. Jute, sisal and wool fibre- reinforced PP and PLA composites were prepared using a novel, patented nonwoven technology followed by the hot press method. The prepared composites were aged in water and chemical solutions for up to 3 week periods. Water absorption, flexural properties and the thermal and flammability performances of the composites were investigated before and after ageing each process. The effect of post-ageing drying on the retention of mechanical and flammability properties has also been studied. A linear relationship between irreversible flexural modulus reduction and water adsorption/desorption was observed. The aqueous chemical solutions caused further but minor effects in terms of moisture sorption and flexural modulus changes. PLA composites were affected more than the respective PP composites, because of their hydrolytic sensitivity. From thermal analytical results, these changes in PP composites could be attributed to ageing effects on fibres, whereas in PLA composite changes related to both those of fibres present and of the polymer. Ageing however, had no adverse effect on the flammability of the composites.

Preparation and Characterization of Electrospun Polylactic Acid (PLA) Fiber Loaded with Birch Bark Triterpene Extract for Wound Dressing.

Drug-loaded electrospun fibers have attracted increasing attention as a promising wound dressing material due to their capability of preventing from infections and inflammation and maintaining an appropriate environment for wound healing. In this study, polylactic acid (PLA), which is widely used in wound management, was chosen as electrospinnable polymer. A triterpene extract (TE) from the outer bark of birch known for its anti-inflammatory, antiviral, antibacterial, and wound healing effects was chosen to produce TE-loaded PLA electrospun fibers for wound dressing. A binary solvent system of dichloromethane (DCM) and dimethyl sulfoxide (DMSO) was employed, and the ratio of the solvents was optimized for preparing smooth and uniform fibers. The morphology of TE-loaded PLA electrospun fibers was investigated by scanning electron microscopy (SEM). The entrapment of TE in PLA fibers was confirmed by confocal laser scanning microscopy (CLSM). Differential scanning calorimetry (DSC) and X-ray diffraction (XRD) were used to analyze the solid state of TE in PLA fibers. The release behavior of TE was assayed by a shaking flask method for a period of 96 h. The results revealed that TE-loaded electrospun PLA microfibers could be reliably prepared and are promising future candidates in wound therapy.

Constructing slow-release formulations of herbicide metribuzin using its co-extrusion with biodegradable polyester poly-ε-caprolactone.

Different technologies to prepare long term pesticide forms include polymer coating, preparing composites and encapsulating pesticides in nanoparticles. A simple and low-cost method was proposed to obtain slow-release formulations by co-extrusion of a pesticide with a biodegradable polymer at a temperature above the melting points of both components. A herbicide metribuzin and low-melting polyester poly-ε-caprolactone were chosen for this work. Formulations containing 10%, 20%, and 40% herbicide were prepared. During 7 days of their exposition in water, it was released from 81% to 96% of initially loaded metribuzin; the highest release was detected for 40%-loaded forms. Biodegradation of the constructs and pesticide release were further studied in the model soil. Degradation rates of the specimens increased with an increase in pesticide content, from 9% to 20% over 14 weeks for the 10%/20%-loaded and the 40%-loaded specimens, respectively. The release of metribuzin reached, respectively, 37-38% and 55%. The herbicide content in soil was lower due to its partial degradation in soil; it reached 23-25% and 33%, respectively, from initially loaded into the polymer matrix. Release kinetics of metribuzin in water as in soil best fitted the First-order model. The used approach is promising for obtaining long-term release formulations for soil applications.

Innovative smart and biodegradable packaging for margarine based on a nano composite polylactic acid/lycopene film.

In this study, polylactic acid (PLA)/titanium dioxide/lycopene (PLA/TiO2/Lyc) nano-composite film was prepared. The morphology and mechanical properties of the film were studied by SEM and texture analyser. Results showed that lycopene and TiO2 nanoparticles were distributed in the film matrix uniformly, TiO2 and lycopene increased the mechanical properties of PLA film. The PLA/TiO2/Lyc film was used to package margarine. The effect of PLA/TiO2/Lyc film, time and temperature of storage on the qualitative features of margarine were studied. Also the colour properties of PLA/TiO2/Lyc film were studied during storage period. Oxidative features (antioxidant activity, acidity number, peroxide value and thiobarbituric acid value) of margarine showed that the quality features of margarine decreased during storage, but the PLA/TiO2/Lyc film controled the oxidative factors and increased the margarine shelf life significantly (P < .05). Results also showed that the PLA/TiO2/Lyc film colour changed from red to light yellow during storage. With increasing margarine storage time, the film colour index a decreased (red colour diminished) while b increased (yellow colour increased). There were good relations between colour changes of film and oxidative parameters of margarine and storage time and storage temperature. Thus PLA/TiO2/Lyc film can be used as a visual indicator of the oxidation variations during storage of packaged margarine.

Effective and Sustained Control of Soil-Borne Plant Diseases by Biodegradable Polyhydroxybutyrate Mulch Films Embedded with Fungicide of Prothioconazole.

Soil-borne diseases and plant rhizosphere nematode have caused many crop yield losses. Increased environmental awareness is leading to more restrictions on the use of certain fumigants and root irrigation methods due to their impact on human health and soil system. Therefore, it is necessary to find alternative treatments to maintain crop economic yields and environmental sustainability. In the present work, biodegradable antifungal mulches were prepared by blending poly(3-hydroxybutyrate-co-4-hydroxybutyrate) (PHB) with fungicide of prothioconazole (PRO), which were used for effective and sustained control of soil-borne plant diseases. To reveal the application prospect of the PHB/PRO composite films in the management of soilborne plant diseases, some physical and biological properties were evaluated. The proper mulch film of PHB/PRO was assessed based on its mechanical and optical properties, while water solubility and the film micromorphology was further characterized. The release patterns of composite films under different pH levels were investigated. Moreover, the in vitro antifungal bioassay and pot experiment showed satisfactory bioactivity of the PHB/PRO films against Sclerotium rolfsii Sacc., a soil-borne disease in peanut fields. This study demonstrated that the biodegradable mulch films containing PRO fungicide are capable of inhibiting soil-borne plant pathogenic fungi effectively, and this facile but powerful strategy may find wide applicability in sustainable plant and horticulture protection.

Mass Spectrometry Imaging of Bio-oligomer Polydispersity in Plant Tissues by Laser Desorption Ionization from Silicon Nanopost Arrays.

Mass spectrometry imaging (MSI) enables simultaneous spatial mapping for diverse molecules in biological tissues. Matrix-assisted laser desorption ionization (MALDI) mass spectrometry (MS) has been a mainstream MSI method for a wide range of biomolecules. However, MALDI-MSI of biological homopolymers used for energy storage and molecular feedstock is limited by, e.g., preferential ionization for certain molecular classes. Matrix-free nanophotonic ionization from silicon nanopost arrays (NAPAs) is an emerging laser desorption ionization (LDI) platform with ultra-trace sensitivity and molecular imaging capabilities. Here, we show complementary analysis and MSI of polyhydroxybutyric acid (PHB), polyglutamic acid (PGA), and polysaccharide oligomers in soybean root nodule sections by NAPA-LDI and MALDI. For PHB, number and weight average molar mass, polydispersity, and oligomer size distributions across the tissue section and in regions of interest were characterized by NAPA-LDI-MSI.