Unraveling the Lignin Structural Variation in Different Bamboo Species.

The structure of cellulolytic enzyme lignin (CEL) prepared from three bamboo species (Neosinocalamus affinis, Bambusa lapidea, and Dendrocalamus brandisii) has been characterized by different analytical methods. The chemical composition analysis revealed a higher lignin content, up to 32.6% of B. lapidea as compared to that of N. affinis (20.7%) and D. brandisii (23.8%). The results indicated that bamboo lignin was a p-hydroxyphenyl-guaiacyl-syringyl (H-G-S) lignin associated with p-coumarates and ferulates. Advanced NMR analyses displayed that the isolated CELs were extensively acylated at the γ-carbon of the lignin side chain (with either acetate and/or p-coumarate groups). Moreover, a predominance of S over G lignin moieties was found in CELs of N. affinis and B. lapidea, with the lowest S/G ratio observed in D. brandisii lignin. Catalytic hydrogenolysis of lignin demonstrated that 4-propyl-substituted syringol/guaiacol and propanol guaiacol/syringol derived from ß-O-4' moieties, and methyl coumarate/ferulate derived from hydroxycinnamic units were identified as the six major monomeric products. We anticipate that the insights of this work could shed light on the sufficient understanding of lignin, which could open a new avenue to facilitate the efficient utilization of bamboo.

Electrolyte Regulation towards Stable Lithium-Metal Anodes in Lithium-Sulfur Batteries with Sulfurized Polyacrylonitrile Cathodes.

Lithium-sulfur (Li-S) batteries are highly regarded as the next-generation energy-storage devices because of their ultrahigh theoretical energy density of 2600 Wh kg-1 . Sulfurized polyacrylonitrile (SPAN) is considered a promising sulfur cathode to substitute carbon/sulfur (C/S) composites to afford higher Coulombic efficiency, improved cycling stability, and potential high-energy-density Li-SPAN batteries. However, the instability of the Li-metal anode threatens the performances of Li-SPAN batteries bringing limited lifespan and safety hazards. Li-metal can react with most kinds of electrolyte to generate a protective solid electrolyte interphase (SEI), electrolyte regulation is a widely accepted strategy to protect Li-metal anodes in rechargeable batteries. Herein, the basic principles and current challenges of Li-SPAN batteries are addressed. Recent advances on electrolyte regulation towards stable Li-metal anodes in Li-SPAN batteries are summarized to suggest design strategies of solvents, lithium salts, additives, and gel electrolyte. Finally, prospects for future electrolyte design and Li anode protection in Li-SPAN batteries are discussed.

Selective precipitation and characterization of lignin-carbohydrate complexes (LCCs) from Eucalyptus.

MAIN CONCLUSION: Six types of lignin-carbohydrate complex (LCC) fractions were isolated from Eucalyptus. The acidic dioxane treatment applied significantly improved the yield of LCCs. The extraction conditions had a limited impact on the LCC structures and linkages. Characterization of the lignin-carbohydrate complex (LCC) structures and linkages promises to offer insight on plant cell wall chemistry. In this case, Eucalyptus LCCs were extracted by aqueous dioxane, and then precipitated sequentially by 70% ethanol, 100% ethanol, and acidic water (pH = 2). The composition and structure of the six LCC fractions obtained by selective precipitation were investigated by sugar analysis, molecular weight determination, and 2D HSQC NMR. It was found that the acidic (0.05-M HCl) dioxane treatment significantly improved the yield of LCCs (66.4% based on Klason lignin), which was higher than the neutral aqueous dioxane extraction, and the extraction condition showed limited impact on the LCC structures and linkages. In the fractionation process, the low-molecular-weight LCCs containing a high content of carbohydrates (60.3-63.2%) were first precipitated by 70% ethanol from the extractable solution. The phenyl glycoside (PhGlc) bonds (13.0-17.0 per 100Ar) and highly acetylated xylans were observed in the fractions recovered by the precipitation with 100% ethanol. On the other hand, such xylan-rich LCCs exhibited the highest frequency of ß-O-4 linkages. The benzyl ether (BE) bonds were only detected in the fractions obtained by acidic water precipitation.

Structural Differences between the Lignin-Carbohydrate Complexes (LCCs) from 2- and 24-Month-Old Bamboo (Neosinocalamus affinis).

The lignin-carbohydrate complex (LCC) was isolated from milled wood lignin of 2- and 24-month-old crude bamboo (Neosinocalamus affinis) culms using acetic acid (AcOH) and then characterized. The results have shown that the LCC preparation from 2-month-old bamboo (L2) exhibited a slightly lower molecular weight than the LCC preparation from the 24-month-old bamboo (L24). Further studies using Fourier transform infrared spectroscopy (FT-IR) and heteronuclear single quantum coherence (2D-HSQC) NMR spectra analyses indicate that the LCC preparations included glucuronoarabinoxylan and G-S-H lignin-type with G>S>>H. The content of the S lignin units of LCC in the mature bamboo was always higher than in the young bamboo. Combined with sugar composition analysis, the contents of phenyl glycoside and ether linkages in the L24 preparation were higher than in the L2 preparation; however, there was a reverse relationship of ester LCC bonds in L2 and L24. Lignin-xylan was the main type of LCC linkage in bamboo LCCs. Lignin-lignin linkages in the LCC preparations included ß-ß, ß-5 and ß-1 carbon-to-carbon, as well as ß-O-4 ether linkages, but ß-1 linkages were not present in L2.

Multi-site sulfonation of lignin for the synthesis of a high-performance dye dispersant.

Sulfonated lignin-based dye dispersants have intensively attracted attention due to their low cost, renewability and abundant sources. However, their utilization is limited by the low content of sulfonic groups and high content of hydroxyl groups in their complex lignin structure, which results in various problems such as high reducing rate of dye, severe staining of the fibers and uneven dyeing. Here, the multi-site sulfonated lignin-based dispersants were prepared with high sulfonic group content (2.20 mmol/g) and low hydroxyl content (2.43 mmol/g). When using it as the dispersant, the dye uptake rate was improved from 69.23 % to 98.55 %, the reducing rate was decreased from 20.82 % to 2.03 %, the K/S value was reduced from 0.69 to 0.02, and the particle sizes in dye system before and after high temperature treatment were stabilized below 0.5 µm. Besides, the dispersion effect was significantly improved because no obvious separation between dye and water was observed even if without the assistance of grinding process. In short, the multi-site sulfonation method proposed in this work could remarkably improve the performances of the lignin-based dye dispersants, which would facilitate the development of the dye dispersion and the high value utilization of lignin.

Carboxymethyl chitosan composited poly(ethylene oxide) electrolyte with high ion conductivity and interfacial stability for lithium metal batteries.

Low ionic conductivity and poor interface stability of poly(ethylene oxide) (PEO) restrict the practical application as polymeric electrolyte films to prepare solid-state lithium (Li) metal batteries. In this work, biomass-based carboxymethyl chitosan (CMCS) is designed and developed as organic fillers into PEO matrix to form composite electrolytes (PEO@CMCS). Carboxymethyl groups of CMCS fillers can promote the decomposition of Lithium bis(trifluoromethane sulfonimide) (LiTFSI) to generate more lithium fluoride (LiF) at CMCS/PEO interface, which not only forms ionic conductive network to promote the rapid transfer of Li+ but also effectively enhances the interface stability between polymeric electrolyte and Li metal. The enrichment of carboxyl, hydroxyl, and amidogen functional groups within CMCS fillers can form hydrogen bonds with ethylene oxide (EO) chains to improve the tensile properties of PEO-based electrolyte. In addition, the high hardness of CMCS additives can also strengthen mechanical properties of PEO-based electrolyte to resist penetration of Li dendrites. LiLi symmetric batteries can achieve stable cycle for 2500 h and lithium iron phosphate full batteries can maintain 135.5 mAh g-1 after 400 cycles. This work provides a strategy for the enhancement of ion conductivity and interface stability of PEO-based electrolyte, as well as realizes the resource utilization of biomass-based CMCS.

Reconstitution of cellulose and lignin after [C2mim][OAc] pretreatment and its relation to enzymatic hydrolysis.

Although the effects of cellulose crystallinity and lignin content as two major structural features on enzymatic hydrolysis have been extensively studied, debates regarding their effects still exist. In this study, reconstitution of cellulose and lignin after 1-ethyl-3-methylimidazolium acetate ([C(2)mim][OAc]) pretreatment was proposed as a new method to study their effects on enzymatic digestibility. Different mechanisms of lignin content for reduction of cellulose hydrolysis were found between the proposed method and the traditional method (mixing of cellulose and lignin). The results indicated that a slight change of the crystallinity of the reconstituted materials may play a minor role in the change of enzyme efficiency. In addition, the present study suggested that the lignin content does not significantly affect the digestibility of cellulose, whereas the conversion of cellulose fibers from the cellulose I to the cellulose II crystal phase plays an important role when an ionic liquid pretreatment of biomass was conducted.

Structural variation of bamboo lignin before and after ethanol organosolv pretreatment.

In order to make better use of lignocellulosic biomass for the production of renewable fuels and chemicals, it is necessary to disrupt its recalcitrant structure through pretreatment. Specifically, organosolv pretreatment is a feasible method. The main advantage of this method compared to other lignocellulosic pretreatment technologies is the extraction of high-quality lignin for the production of value-added products. In this study, bamboo was treated in a batch reactor with 70% ethanol at 180 °C for 2 h. Lignin fractions were isolated from the hydrolysate by centrifugation and then precipitated as ethanol organosolv lignin. Two types of milled wood lignins (MWLs) were isolated from the raw bamboo and the organosolv pretreated residue separately. After the pretreatment, a decrease of lignin (preferentially guaiacyl unit), hemicelluloses and less ordered cellulose was detected in the bamboo material. It was confirmed that the bamboo MWL is of HGS type (p-hydroxyphenyl (H), vanillin (G), syringaldehyde (S)) associated with a considerable amount of p-coumarate and ferulic esters of lignin. The ethanol organosolv treatment was shown to remove significant amounts of lignin and hemicelluloses without strongly affecting lignin primary structure and its lignin functional groups.

Lignin-based composites with enhanced mechanical properties by acetone fractionation and epoxidation modification.

Epoxy resin is widely used in various fields of the national economy due to its excellent chemical and mechanical properties. Lignin is mainly derived from lignocelluloses as one of the most abundant renewable bioresources. Due to the diversity of lignin sources and the complexity as well as heterogeneity of its structure, the value of lignin has not been fully realized. Herein, we report the utilization of industrial alkali lignin for the preparation of low-carbon and environmentally friendly bio-based epoxy thermosetting materials. Specifically, epoxidized lignin with substituted petroleum-based chemical bisphenol A diglycidyl ether (BADGE) in various proportions was cross-linked to fabricate thermosetting epoxies. The cured thermosetting resin revealed enhanced tensile strength (4.6 MPa) and elongation (315.5%) in comparison with the common BADGE polymers. Overall, this work provides a practicable approach for lignin valorization toward tailored sustainable bioplastics in the context of a circular bioeconomy.

Facile construction of lignin-based network composite hydrogel for efficient adsorption of methylene blue from wastewater.

Adsorption method is an effective approach to treat wastewater containing methylene blue. Herein, a cost-effective and eco-friendly lignin-based network composite hydrogel adsorbent (PAA@SML) was constructed by using polyacrylic acid (PAA) to crosslink with sulfomethylated lignin (SML) via free radical polymerization for adsorption of methylene blue (MB) from wastewater. The constructed PAA@SML-0.2 exhibited remarkable adsorption performance towards removal of MB, with a maximum theoretical adsorption capacity of 777.1 mg·g-1. The improved efficiency can be attributed to the well-established network structure and abundant hydrophilic functional groups present in the adsorbent, promoting the interaction between methylene blue (MB) molecules and the adsorption sites of the adsorbent. The adsorption process of the adsorbent for MB followed the pseudo-second-order kinetic and the Langmuir isotherm models, which illustrated the adsorption process attributed to monolayer chemisorption. Mechanism investigation confirmed that the adsorption of MB by PAA@SML-0.2 primarily relied on hydrogen bonding and electrostatic interactions. Moreover, the recyclability test demonstrated excellent regeneration usability and stability of PAA@SML-0.2, and the adsorption capacity maintained above 74.0 % after five cycles. This constructed lignin-based network composite hydrogel is considered to have great potential in the treatment of organic dye in wastewater.

Designed synthesis of multifunctional lignin-based adsorbent for efficient heavy metal ions removal and electromagnetic wave absorption.

Multifunctional lignin-based adsorbents, which have shown great application prospect, have attracted widespread attention. Herein, a series of multifunctional lignin-based magnetic recyclable adsorbents were prepared from carboxymethylated lignin (CL), which was rich in carboxyl group (-COOH). After optimizing the mass ratio of CL to Fe3O4, the prepared CL/Fe3O4 (3:1) adsorbent showed efficient adsorption capacities for heavy metal ions. The kinetic and isotherm nonlinear fitting studies revealed that the adsorption process followed the second-order kinetic and Langmuir models, and the maximum adsorption capacities (Qmax) of CL/Fe3O4 (3:1) magnetic recyclable adsorbent for Pb2+, Cu2+ and Ni2+ ions reached 189.85, 124.43 and 106.97 mg/g, respectively. Meanwhile, after 6 cycles, the adsorption capacities of CL/Fe3O4 (3:1) for Pb2+, Cu2+ and Ni2+ ions could keep at 87.4 %, 83.4 % and 82.3 %, respectively. In addition, CL/Fe3O4 (3:1) also exhibited excellent electromagnetic wave absorption (EMWA) performance with a reflection loss (RL) of -28.65 dB at 6.96 GHz under the thickness of 4.5 mm, and its effective absorption bandwidth (EAB) achieved 2.24 GHz (6.08-8.32 GHz). In short, the prepared multifunctional CL/Fe3O4 (3:1) magnetic recyclable adsorbent with outstanding adsorption capacity for heavy metal ions and superior EMWA capability opens a new avenue for the diversified utilization of lignin and lignin-based adsorbent.

Valorization of lignin through reductive catalytic fractionation of fermented corn stover residues.

The fermented corn stover residues are abundant renewable lignin-rich bioresources that show great potential to produce aromatic phenols. However, selective catalytic hydrogenolysis of this residual material still remains challenge to obtain high yields. Herein, a novel strategy to produce monophenolic compounds from the fermented stover over a commercial Pd/C catalyst was proposed. Taking the reaction temperature as the key variable, the highest monomer yield was 28.5 wt% at 220 °C in compaction with that of the pristine corn stover (22.8 wt%). The enhanced monophenol yield was due to the higher contents of lignin and less recalcitrance in the fermented stover. Moreover, the van Krevelen diagram revealed a slight selective CO bond scission of lignin macromolecular during fermentation as well as the dehydration and deoxygenation in hydrogenolysis reaction. Overall, this work opens a new avenue for the valorization of lignin through reductive catalytic fractionation of agricultural wastes.

Renewable galactomannan-based biogums with structure regulation to protect zinc metal anodes via blocking and confinement effect.

Galactomannan-based biogums were derived from fenugreek, guar, tara, and carob and consisted of mannose and galactose with different ratios, as well as the implementation of high-value utilization was very significant for sustainable development. In this work, renewable and low-cost galactomannan-based biogums were designed and developed as functional coatings protected on the Zn metal anodes. The molecule structure of galactomannan-based biogums were explored on the effect of anticorrosion ability and uniform deposition behavior through the introduction of fenugreek gum, guar gum, tara gum, and carob gum with different ratios of mannose to galactose as 1.2:1, 2:1, 3:1, and 4:1. The existence of biogum protective layers can reduce the contact area between Zn anodes and aqueous electrolyte to enhance the anticorrosion ability of Zn anodes. Rich oxygen-containing groups in galactomannan-based biogums can coordinate with Zn2+ and Zn atoms to form ion conductivity gel layer and adsorb closely on the surface of Zn metal, which can induce uniform deposition of Zn2+ to avoid dendrite growth. Zn electrodes protected by biogums can cycle impressively for 1980 h with 2 mA cm-2 and 2 mAh cm-2. This work can provide a novel strategy to enhance Zn metal anodes' electrochemical performance, as well as implement the high-value application of biomass-based biogums as functional coatings.

Surface Control Behavior toward Crystal Regulation and Anticorrosion Capacity for Zinc Metal Anodes.

The commercial application of high-safety aqueous zinc (Zn) secondary batteries is hindered by the poor cycling life of Zn metal anodes. Here we propose a dendrite growth and hydrogen evolution corrosion reaction mechanism from the binding energy of the deposited crystal plane on the Zn surface and the adsorption energy of H2O molecules on different crystal planes as well as the binding energy of H2O molecules with Zn2+ ions. The biomass-based alkyl polyglucoside (APG) surfactant is adopted as an electrolyte additive of 0.15% to regulate the preferential growth of a parallel Zn(002) plane and enhance the anticorrosion ability of Zn metal anodes. The robust binding and adsorption energies of APG with Zn2+ ions in the aqueous electrolyte and the Zn(002) plane on Zn surface generate a synergistic effect to increase the concentration of Zn2+ ions on the APG-adsorbed Zn(002) plane, endowing the continuous growth of the preferential parallel Zn(002) plane and the excellent anticorrosion capacity. Accordingly, the long-term cycle stability of 4000 h can be achieved for Zn anodes with APG additives, which is better than that with pure ZnSO4 electrolyte. With the addition of APG in the anolyte electrolyte, Zn-I2 full cells display excellent cycling performance (70 mAh g-1 after 20000 cycles) as compared with that without APG additives.

Microwave-assisted organic acid extraction of lignin from bamboo: structure and antioxidant activity investigation.

Microwave-assisted extraction in organic acid aqueous solution (formic acid/acetic acid/water, 3/5/2, v/v/v) was applied to isolate lignin from bamboo. Additionally, the structural features of the extracted lignins were thoroughly investigated in terms of C9 formula, molecular weight distribution, FT-IR, (1)H NMR and HSQC spectroscopy. It was found that with an increase in the severity of microwave-assisted extraction, there was an increase of phenolic hydroxyl content in the lignin. In addition, an increase of the severity resulted in a decrease of the bound carbohydrate content as well as molecular weight of the lignin. Antioxidant activity investigation indicated that the radical scavenging index of the extracted lignins (0.35-1.15) was higher than that of BHT (0.29) but lower than that of BHA (3.85). The results suggested that microwave-assisted organic acid extraction provides a promising way to prepare lignin from bamboo with good antioxidant activity for potential application in the food industry.

Compared study on the cellulose/CaCO3 composites via microwave-assisted method using different cellulose types.

The purposes of this study were to explore the influences of different cellulose types on the cellulose/CaCO3 composites, which were synthesized via the microwave-assisted method by using alkali extraction cellulose and microcrystalline cellulose, respectively. Experimental results demonstrated that the types of cellulose played an important role in the microstructure and morphologies of the cellulose/CaCO3 composites. The composites consisted of cellulose and pure phase CaCO3 (calcite). The sample synthesized using microcrystalline cellulose had better crystallinity than that of the sample using alkali extraction cellulose. The cellulose fibers and CaCO3 particles were observed using alkali extraction cellulose. However, using microcrystalline cellulose instead of alkali extraction cellulose, the cellulose with irregular shape and CaCO3 microspheres were obtained. Therefore, choosing appropriate cellulose types is very important for the formation of cellulose/CaCO3 composites. Furthermore, the Raman spectra of the cellulose/CaCO3 composites were also researched.

Cellulose-based bio-adsorbent from TEMPO-oxidized natural loofah for effective removal of Pb(II) and methylene blue.

Excessive discharge of inorganic and organic contaminants in water poses a serious threat to the ecosystems. However, most synthetic adsorbents lack cost-effectiveness in terms of preparation. Interestingly, loofah sponge (LS) was a natural absorbent that could effectively remove pollutions in wastewater, but its adsorption capacity is barely satisfactory. Herein, we present a novel strategy of TEMPO-oxidized loofah sponge (TOLS) to boost the adsorption performance of LS. The batch experiments demonstrated that the maximum removal capacity of TOLS for Pb(II) and methylene blue (MB) was 96.6 mg/g and 10.0 mg/g, respectively, which were 3.5 and 1.3 times that of pristine LS. Notably, the continuous-flow reaction testing of the mixed solution revealed that the elimination rate of Pb(II) and MB was still better than 90 % even after 16 h. Such excellent performance was benefit from the enhanced specific surface area and surface carboxyl content of TOLS. This work offers new insights into the rational development of multifunctional and inexpensive cellulose-based bio-adsorbents for wastewater remediation.

Fabricating lignin-based carbon nanofibers as versatile supercapacitors from food wastes.

Recently, the high-value utilization of food wastes has attracted great interest in sustainable development. Focusing on the major application of electrochemical energy storage (ECES), light-weight lignin-based carbon nanofibers (LCNFs) were controllably fabricated as supercapacitors from melon seed shells (MSS) and peanut shells (PS) through electrospinning and carbonizing processes. As a result, the optimal specific capacitance of 533.7 F/g in three-electrode system, energy density of 69.7 Wh/kg and power density of 780 W/Kg in two-electrode system were achieved. Surprisingly, the LCNFs also presented a satisfied electromagnetic absorption property: The minimum reflection loss (RL) value reached -37.2 dB at an absorbing frequency of 7.98 GHz with an effective frequency (RL < 10 dB) of 2.24 GHz (6.88 to 9.12 GHz) at a thickness of 3.0 mm. These features make the multifunctional LCNFs highly attractive for light-weight supercapacitor electrodes and electromagnetic wave absorbers applications.

Nanocomposite films based on xylan-rich hemicelluloses and cellulose nanofibers with enhanced mechanical properties.

Interest in xylan-rich hemicelluloses (XH) film is growing, and efforts have been made to prepare XH films with improved mechanical properties. This work described an effective approach to produce nanocomposite films with enhanced mechanical properties by incorporation of cellulose nanofibers (CNFs) into XH. Aqueous dispersions of XH (64-75 wt %), sorbitol (16-25 wt %), and CNF (0-20 wt %) were cast at a temperature of 23 °C and 50% relative humidity. The surface morphology of the films was revealed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The thermal properties and crystal structure of the films were evaluated by thermal analysis (TG) and X-ray diffraction (XRD). The surface of XH films with and without CNF was composed primarily of nanonodules, and CNFs were embedded in the XH matrix. Freeze-dried XH powder was amorphous, whereas the films with and without CNF showed a distinct peak at around 2θ = 18°, which suggested that XH molecules aggregated or reordered in the casting solution or during water evaporation. Furthermore, the nanocomposite films had improved thermal stability. XH film with 25 wt % plasticizer (sorbitol, based on dry XH weight) showed poor mechanical properties, whereas incorporation of CNF (5-20 wt %, based on the total dry mixture) into the film resulted in enhanced mechanical properties due to the high aspect ratio and mechanical strength of CNF and strong interactions between CNF and XH matrix. This effective method makes it possible to produce hemicellulose-based biomaterials of high quality.

Structural and thermal characterization of galactomannans from genus Gleditsia seeds as potential food gum substitutes.

BACKGROUND: Seed galactomannans are preferred hydrocolloids since they are comparatively cheap, non-toxic, eco-friendly and non-polluting during production and application. Galactomannans from seeds of three species of Gleditsia, namely G. sinensis, G. microphylla and G. melanacantha, were characterized in terms of structural and thermal properties. RESULTS: Gleditsia polysaccharides were characterized using both chemical and chromatographic methods, as well as Fourier transform infrared, (1) H nuclear magnetic resonance (NMR) and (13) C NMR spectroscopy, and it was shown that they consist of D-mannopyranose and D-galactopyranose residues. The mannose/galactose (M/G) ratio of galactomannans was 3.25, 3.31 and 2.30, respectively. It was also found that these polysaccharides differ from one another in values of M(w) , M(n) and polydispersity. X-ray diffraction confirmed the amorphous nature of Gleditsia galactomannans, although G. sinensis galactomannan showed a high crystallinity. Thermal analysis of the galactomannans by differential scanning calorimetry illustrated that their endothermic peaks ranged from 290 to 320 °C. CONCLUSION: Gleditsia polysaccharides are neutral galactomannans. The higher value of M/G ratio from G. sinensis and G. microphylla indicates that their gums offer an excellent alternative for locus bean gum.