Evaluation of image quality and patient exposure in fluoroscopy using a phantom: Is there any clinical relevance?

OBJECTIVE: To investigate the impact of X-ray preset acquisition protocol settings on fluoroscopy image quality (IQ) and radiation exposure. MATERIALS & METHODS: A quality control (QC) phantom was imaged with a modern digital C-arm system, using various preset fluoroscopy protocols. IQ was assessed using human observers and in-house software for automated evaluation, based on contrast-to-noise ratios of details and their background. Patient radiation exposure was evaluated using the displayed Incident Air-Kerma and Kerma-Area Product values. RESULTS: Protocol selection affects radiation exposure by a factor of about 3. IQ evaluation showed that acquisition protocols produce images with quite different characteristics. The visual IQ evaluation method was time consuming and cumbersome. The automated method, utilized the visual IQ evaluation results for calibration of detection thresholds. However, it failed to reproduce these results for all images and details types. In some images, digital image processing created artifacts which affected the pixel value distributions around details in a way that could be handled only by the human vision. CONCLUSION: Manufacturers provide many preset protocols designated for specific clinical uses, which have large impact on IQ characteristics and radiation exposure. However, protocol settings' selection rationale is essentially a "black box" for the end user. Though QC phantoms are currently used for IQ evaluation, they are not appropriate for drawing firm conclusions concerning the expected performance of each protocol in clinical practice. Currently, there is no consensus on the optimum technical characteristics of preset protocols for specific procedures. More work is needed in this area.

PATIENT DOSES IN WHOLE-BODY PET/CT EXAMINATIONS IN THE LARGEST TERTIARY HOSPITAL IN GREECE.

The purpose of this study was to determine the patient radiation dose in combined whole-body positron emission tomography/computed tomography (PET/CT) examinations performed in the largest tertiary hospital in Greece. Computed tomography dose index (CTDIvol), dose length product (DLP), weight, height and administered activity of 2-[18F] fluoro-2-deoxy-D-glucose values for PET/CT examinations were recorded in a sample of 1014 randomly selected patients. The mean (±standard deviation) and median (interquartile) CTDIvol values were equal to 5.5 ± 2.4 and 4.8 (2.5) mGy, respectively. The respective DLP values were 483.3 ± 212.4 and 426 (234.6) mGy·cm. For the administered activity, mean and median were equal to 363.9 ± 68.3 and 361.6 (85.6) MBq. The mean administered activity per body weight was 4.8 ± 0.6 and the median 4.8 (0.6) MBq/kg. The results of this survey are within the range of values reported in the literature and can be used as a standard of reference until national diagnostic reference levels are established for whole-body PET/CT procedures.

Multi-channel magnetoencephalogram on Alzheimer disease patients.

Magnetoencephalogram (MEG) recordings of 8 patients with advanced Alzheimer Disease (AD) and 9 normal individuals were obtained with a 122-channel whole head biomagnetometer SQUID (Superconductive Quantum Interference Device) to record the minute magnetic fields generated by the brain. The obtained MEG signals were analyzed using linear signal analysis techniques such as Fourier Transform in order to get the frequency distribution of MEG values. The obtained frequencies from all MEG sensors located outside the scalp of each subject were stored for evaluation. From this evaluation it was concluded that in patients with AD the dominant frequencies were significantly lower compared to normal individuals.

The impact of image processing algorithms on digital radiography of patients with metalic hip implants.

OBJECTIVE: To investigate the impact of image processing algorithms on image quality of digital radiographs. This study was motivated from a case of a patient with metallic hip implant, where the anatomy around the implant was misrepresented, due to failure of the processing algorithm. MATERIALS & METHODS: A quality control phantom was imaged using a digital radiographic unit and the standard examination protocol for Pelvis anteroposterior (AP) projection. The original image was reprocessed with all available selections of Diamond View, which is a processing algorithm for optimizing image quality of different anatomic regions. The same procedure was repeated for two other examination protocols, Femur AP and Hip AP, which differ in terms of harmonization kernel and gain, and look up table settings. The whole procedure was repeated with a Pb strip, 2 cm wide and 3 mm thick, positioned close to the right phantom edge, in order to simulate a metallic hip implant. Using ImageJ a number of regions of interest (ROIs) were positioned on the phantom images and the impact of processing parameters on certain image characteristics and image quality indices was evaluated. RESULTS: Processing parameters have a strong impact on image characteristics, but in terms of image quality, differences between images with and without the implant are small. Exception is the regions in the vicinity of the implant, where larger differences, that could affect diagnosis, were observed. CONCLUSION: In case of doubt, additional processing with settings which minimize the risk of anatomic misrepresentation should be used.

Correlation of image quality with exposure index and processing protocol in a computed radiography system.

The correlation of image quality with the exposure index (EI) and the processing protocol was investigated in a Kodak computed radiography (CR) system using clinical radiographs and a water phantom containing an aluminium and a copper step-wedge. The phantom was exposed to different dose levels and the acquired images were processed using four clinical protocols. The quality of these images was evaluated in terms of image brightness, contrast and noise. In clinical radiographs, there was no straightforward correlation of image quality with EI. In phantom images, higher EI values improved contrast and reduced noise but after a point this improvement does not justify the implied increase in patient dose. Image brightness, contrast and noise were also strongly dependent on the processing protocol. To obtain the images of satisfactory quality with the Kodak CR system, a dose slightly higher than those used in 400 relative speed screen-film systems and a processing protocol designated for the specific radiographic examination are required.

Comparison of patient doses in interventional radiology procedures performed in two large hospitals in Greece.

Purpose of the study was to determine patient doses in the most common interventional radiology (IR) procedures performed in two large Greek hospitals. A total of 164 patients who underwent 4 types of IR procedures were studied. Fluoroscopy time, total exposure time, number of frames, number of runs, radiation field size, and cumulative dose-area product (DAP) were recorded. The median DAP values for carotid arteriography and lower limb arteriography were 66 and 123 Gy cm2 for hospital 'A' and 21 and 49 Gy cm2 for hospital 'B'. For the cerebral arteriographies performed in hospital 'A', the median DAP was 116 Gy cm2, while for the hepatic embolizations performed in hospital 'B', it was 104 Gy cm2. The DAP values observed in hospital 'A' for carotid arteriography and lower limb arteriography were almost three times than those of hospital 'B'. From the data analysis, it is evident that dose optimization in hospital 'A' should be pursued through revision of the techniques used.

The potential role of brachytherapy in the irradiation of patients with lung cancer: a systematic review.

To review the use of brachytherapy as an adjuvant therapy to reduce recurrences after sublobar resections and as a palliation to patients with inoperable disease. Α review of all published studies was performed to identify the recurrence rate after brachytherapy adjuvant to sublobar resection and assess the palliation of symptoms and the complications of brachytherapy as a palliative treatment. Most of the studies that we found about brachytherapy as an adjuvant therapy to sublobar resection due to patient's poor cardiopulmonary reserve showed that brachytherapy offered low recurrence rate with low toxicity. Ten studies concerning palliative brachytherapy showed improvement of symptoms with good tolerance and good endoscopic response rates. Literature suggests that brachytherapy for inoperable symptomatic disease can be delivered for symptom improvement with acceptable toxicity. Brachytherapy as an alternative treatment option for lung cancer needs more investigation with more prospective trials.

Excessive leakage radiation measured on two mobile X-ray units due to the methodology used by the manufacturer to calculate and specify the required tube shielding.

During the quality control (QC) procedure of a new mobile X-ray unit, it was revealed that the leakage radiation was well in excess of the current limit of 1 mSv h(-1). As a result, this unit was returned to the vendor company and it was replaced by a new unit of the same brand and model. Leakage measurements revealed that the second unit presented the same problem. After consulting the vendor company and the tube manufacturer, it was discovered that the excessive leakage identified in these two X-ray units was not due to a defective construction, but due to the methodology with which the maximum permissible leakage and therefore the tube shielding had been determined. In this study, the implications of using such methods to the radiation protection of personnel and public are discussed.

Image quality and breast dose of 24 screen-film combinations for mammography.

In this study the effect of different mammographic screen-film combinations on image quality and breast dose, and the correlation between the various image quality parameters, breast dose and the sensitometric parameters of a film were investigated. Three Agfa (MR5-II, HDR, HT), two Kodak (Min-R M, Min-R 2000), one Fuji (AD-M), one Konica (CM-H) and one Ferrania (HM plus) single emulsion mammographic films were combined with three intensifying screens (Agfa HDS, Kodak Min-R 2190 and Fuji AD-MA). The film characteristics were determined by sensitometry, while the image quality and the dose to the breast of the resulting 24 screen-film combinations were assessed using a mammography quality control phantom. For each combination, three images of the phantom were acquired with optical density within three different ranges. Two observers assessed the quality of the 72 phantom images obtained, while the breast dose was calculated from the exposure data required for each image. Large differences among screen-film combinations in terms of image quality and breast dose were identified however, that, could not be correlated with the film's sensitometric characteristics. All films presented the best resolution when combined with the HDS screen at the expense of speed, and the largest speed when combined with the AD-MA screen, without degradation of the overall image quality. However, an ideal screen-film combination presenting the best image quality with the least dose was not identified. It is also worth mentioning that the best performance for a film was not necessarily obtained when this was combined with the screen provided by the same manufacturer. The results of this study clearly demonstrate that comparison of films based on their sensitometric characteristics are of limited value for clinical practice, as their performance is strongly affected by the screens with which they are combined.

Optical density variations in CT films and their effect on image quality.

It was recently reported that optical density (OD) variations were observed in CT films printed with a laser camera, depending on the printing format and the frame position within the film. The purpose of the present study was to investigate if these variations are common to both laser and dry-film printers and if the different OD settings along with day-to-day and frame-to-frame variations may affect the image quality. Eight laser and five dry-film printers installed at 12 different CT facilities were tested. For each one, the SMPTE test pattern was printed on all frames of a film using the same printing format. The ODs of the 0%, 10%, 40% and 70% patches of the 11-step greyscale of the SMPTE patterns were measured with a densitometer in all frames, while all films were examined on a viewing box to assess subjectively the image quality by visual inspection of the test pattern. A wide range of OD settings and variations were recorded. Frame-to-frame variations in the same film of up to 0.19, 0.15 and 0.21 OD, were observed for contrast index (CI, the OD difference of patches 10% and 70%), speed index (SI, the OD of patch 40%) and maximum OD (OD(max), the OD of patch 0%), respectively. The variations were not always of the same magnitude, nor always followed the same pattern, even for printers of the same model. Considering all films and frames, the CI ranged from 1.26 to 1.74, the SI from 0.68 to 1.43 and the OD(max) from 2.5 to 3.11 OD, well beyond the proposed settings and tolerances of 1.55+/-0.15, 1.15+/-0.1 and 2.45+/-0.1 given in the literature for CI, SI and OD(max), respectively. Despite these large differences, the various problems that were identified in image quality from the visual inspection of the films could not be directly attributed to OD settings, as films with similar CI, SI and OD(max) presented quite different image quality levels. Therefore, for routine quality control, thorough visual inspection of the SMPTE test pattern provides all the necessary information about the imaging chain status.

Patient radiation doses in various fluoroscopically guided orthopaedic procedures.

All orthopaedic fluoroscopic procedures performed using C-arm guidance were monitored for 1 y. The type of procedure, fluoroscopy time (T), kerma-area product (KAP) values and number of radiographs (F) were recorded. The two most often performed techniques were as follows: intramedullary nailing (IMN) of intertrochanteric/peritrochanteric (IP) fractures (101 cases, 49.3 %) and antergrade IMN of femur or tibia shaft (TS) fractures (28 cases, 13.7 %). For the remaining procedures, none accounted for >5 %, categorised as 'various' (76 cases, 37 %). Large variations in T, KAP and F were observed. For IMN of IP fractures, antergrade IMN of femur and TS fractures and for various procedures, respectively, median values were T--2.1, 2.2 and 0.6 min, KAP--6.3, 6.3 and 0.6 Gy cm(-2) and F--21, 2.2 and 6.7. The patient doses during fluoroscopically guided procedures are relatively low compared with other interventional procedures.

THE IMPACT OF X-RAY UNIT TYPE USED FOR ENDOSCOPIC RETROGRADE CHOLANGIOPANCREATOGRAPHY PROCEDURES ON PATIENT DOSES.

To investigate whether the X-ray unit type used for interventional endoscopic retrograde cholangiopancreatography (ERCP) procedures may affect patient radiation doses. A total of 471 ERCP procedures performed in 4 hospitals with 4 types of X-ray units were studied. Kerma-area product (KAP), fluoroscopy time (T) and total number of radiographs acquired (F) were recorded. KAP, T and F values exhibited a great variation, ranging from 0.1 to 130.2 Gy cm2 (mean 16 Gy cm2), 0.13 to 33.7 min (mean 5.4 min) and 0 to 26 radiographs (mean 3.5), respectively. The respective mean values for the four types of X-ray units that were investigated were as follows: KAP: 17.4, 12.5, 5.6 and 36.3 Gy cm2, T: 4.7, 5.2, 3.8 and 11.5 min and F: 1.7, 7.4, 1.9 and 4.6 radiographs. The type of the X-ray unit seems to significantly affect patient radiation dose, with the C-arm delivering the lowest and the angiography unit the highest patient doses.

Analysis of radiological examination request forms in conjunction with justification of X-ray exposures.

OBJECTIVES: To evaluate the adequacy of patient data and clinical information transmitted to the radiological departments by the referring clinicians in view of the justification demands concerning the radiological examinations, as those are described in the Radiation Protection Regulations of the European Union Nations. MATERIALS AND METHODS: Request forms for 1708 patients referred to radiology department and 410 referred to the CT department were evaluated concerning the proper completion of the form fields. Furthermore, for CT examinations a more detailed evaluation was carried out, to assess the rationalistic use of CT within the diagnostic algorithm. RESULTS: Not properly completed request forms to both departments were observed, however, the omissions were more prominent for the referrals to the radiology department, where the age and the probable clinical diagnosis was not given in 81.5 and 46% of the forms, respectively. Furthermore, the emergency indication was less cautiously used compared to the CT requests. For the CT department 33.3% of requests were justified and the final diagnosis was included in the referring doctor's probable clinical diagnosis. U/S was the examination of choice in 51% of the cases where an examination should have been performed before CT and in 70.6% of the cases where an alternative examination was proposed. CONCLUSIONS: The inadequate transmission of clinical information and the large number of not fully justified CT requests observed in this study are typical examples of the various problems that radiologists have to face in order to apply the justification directives.

Radiation doses to patients from digital subtraction angiography.

This investigation determined patient doses during digital subtraction angiography (DSA). Fluoroscopy time, dose-area product (DAP) and entrance surface air kerma (ESAK) were analysed from 263 DSA examinations, classified into seven categories: (1) abdominal aorta, iliac, femoral, popliteal and leg arteries; (2) abdominal aorta and superselective DSA of renal arteries; (3) combination of (1) and (2); (4) superselective DSA of common carotid and vertebral arteries, intracranial branches in face and profile projections; (5) superselective DSA of hepatic, splenic, superior and inferior mesenteric arteries; (6) combination of (1) and (4); and (7) celiac trunk and branches. Median DAP values were 67.7, 92.9, 76.6, 53.6, 105.7, 76.1 and 2.6 Gy cm2, respectively. With the exception of one examination, ESAK values were below 2 Gy: the limit for erythema. Compared with published data, DAP values were within the range reported for (1) and (4), slightly larger for (2) and (5), whereas no references were identified for the remaining three categories.

Radiation doses to patients from enteroclysis.

The purpose of this study was to determine the patient doses during enteroclysis and compare them with the available bibliographical data. For 14 enteroclysis examinations, the dose-area product (DAP) meter readings, fluoroscopy time, number of radiographs and exposure data were recorded. From these data, the fluoroscopy and radiography contributions to DAP, the entrance surface dose (ESD) and the effective dose (E) for each examination were estimated. The mean DAP was 81 Gy cm(2) and the mean fluoroscopy time was 19.5 min. The fluoroscopy contribution to DAP was 77% and 8.7 films were acquired in each examination on average. The mean ESD and E were estimated to be 428 mGy and 21 mSv, respectively. The mean DAP and fluoroscopy time calculated in this study are quite high when compared with those reported in the literature, suggesting that the examination technique should be reviewed and the ways to reduce patient exposure without compromising the diagnostic quality should be acquired.

Measuring skin dose in CT examinations under complex geometries: Instruments, methods and considerations.

OBJECTIVE: To investigate skin dose in Computed Tomography (CT) and its dependence on scanning geometry. MATERIALS AND METHODS: Measurements of entrance surface air kerma (ESAK) in free air and entrance skin dose (ESD) on an anthropomorphic phantom were performed in a 64-slice CT scanner, using two different instruments: the Dose Profiler (DP) and the QED skin diode (QEDSD). Using DP and QEDSD, the ESAK rate profiles at the isocenter and at different distances from it, were measured using axial scans. Using DP and helical scans the ESAK rate profile in the Z-axis was acquired. The same profile was acquired with the QEDSD also, using many axial scans and manual table translation. ESD measurements were performed with the DP and QEDSD, in axial and helical scan mode. RESULTS: ESAK measurements with DP and QEDSD were in good agreement, for both point dose and profile measurements. The agreement was also good for ESD measurements but not for helical scans, due to variable X-ray beam overlapping and different tube angular positions at each scan start. It was observed that the ESD values at different Y-axis offsets were comparable to the respective ESAK values recorded at the same Y-axis offset distances without the phantom. CONCLUSIONS: Both DP and QEDSD were proven suitable for performing point ESD measurements. However, calculating the skin dose distribution in CT examinations is a very challenging task. A practical approach would be for CT scanners to provide a conservative estimate of the peak skin dose using the isocenter ESAK value.

Dual-energy contrast-enhanced digital mammography: Glandular dose estimation using a Monte Carlo code and voxel phantom.

PURPOSE: To estimate the mean glandular dose of contrast enhanced digital mammography, using the EGSnrc Monte Carlo code and female adult voxel phantom. METHODS: Automatic exposure control of full field digital mammography system was used for the selection of the X-ray spectrum and the exposure settings for dual energy imaging. Measurements of the air-kerma and of the half value layers were performed and a Monte Carlo simulation of the digital mammography system was used to compute the mean glandular dose, for breast phantoms of various thicknesses, glandularities and for different X-ray spectra (low and high energy). RESULTS: For breast phantoms of 2.0-8.0 cm thick and 0.1-100% glandular fraction, CC view acquisition, from AEC settings, can result in a mean glandular dose of 0.450 ± 0.022 mGy -2.575 ± 0.033 mGy for low energy images and 0.061 ± 0.021 mGy - 0.232 ± 0.033 mGy for high energy images. In MLO view acquisition mean glandular dose values ranged between 0.488 ± 0.007 mGy - 2.080 ± 0.021 mGy for low energy images and 0.065 ± 0.012 mGy - 0.215 ± 0.010 mGy for high energy images. CONCLUSION: The low kV part of contrast enhanced digital mammography is the main contributor to total mean glandular breast dose. The results of this study can be used to provide an estimated mean glandular dose for individual cases.

A model for calculating shielding requirements in diagnostic X-ray facilities.

In this study a new model for calculating shielding requirements in diagnostic X-ray facilities is presented. It is based on the combination and modification of models and concepts originally proposed by other authors in order to calculate barrier requirements in diagnostic X-ray facilities accurately and realistically without unjustified exaggerations. With this model, multiple sources of radiation operating at different potentials, leakage radiation reduction when operating at potentials less than the maximum rated value, secondary radiation use factors reduction for primary barriers, attenuation by image receptor hardware and existing building materials are all taken into account. Examples of shielding calculations for typical cases are given illustrating the differences between the various models and concepts proposed, as well as the potential reduction in shielding requirements without compromising the radiation protection of public and staff.

Dose calculations for asymmetric fields defined by independent collimators using symmetric field data.

Several methods have been developed for the dosimetry of asymmetric radiation fields formed by independently moving collimator jaws. Three of these methods, based on different principles and modified to comply with our set of available data, are utilized for the calculation of asymmetric field dose profiles. All three methods use output factors and per cent depth doses or tissue maximum ratios of symmetric fields. In the first method, calculation of the off-centre ratio (OCR) of the asymmetric field is based on the symmetric field from which the asymmetric is originated, by setting the one jaw in an asymmetrical position. In the second method the OCR of the symmetric field is used for the OCR calculation of the asymmetric field of the same size; whereas the third method does not allow for the asymmetric OCR calculation. The results obtained using data for the 6 MV photon beam of a Philips SL-20 linear accelerator indicate that both the first and second method can accurately reproduce asymmetric field profiles from symmetric field data; the third method does not allow for penumbra reproduction, but it is accurate at the central part of the asymmetric field. The problems encountered in the application of the three methods are reported and their accuracy is compared.

The diagnostic X-ray protection characteristics of Ytong, an aerated concrete based building material.

Ytong is a widely used building material. The X-ray attenuation properties of Ytong for broad beam geometry conditions and for tube potentials in the 50-140 kVp range are investigated. Comparisons with published data for concrete and other building materials are made. The results suggest that Ytong is not suitable for primary X-ray shielding in common diagnostic installations. However, walls of Ytong, typically 15-20 cm thick, may offer adequate protection in dental and mammography installations, as well as in low workload diagnostic installations as a secondary barrier.