3D-printed electrochemical cells with laser engraving: developing portable electroanalytical devices for forensic applications.

A new electrochemical device fabricated by the combination of 3D printing manufacturing and laser-generated graphene sensors is presented. Cell and electrodes were 3D printed by the fused deposition modeling (FDM) technique employing acrylonitrile butadiene styrene filament (insulating material that composes the cell) and conductive filament (lab-made filament based on graphite dispersed into polylactic acid matrix) to obtain reference and auxiliary electrodes. Infrared-laser engraved graphene, also reported as laser-induced graphene (LIG), was produced by laser conversion of a polyimide substrate, which was assembled in the 3D-printed electrochemical cell that enables the analysis of low volumes (50-2000 µL). XPS analysis revealed the formation of nitrogen-doped graphene multilayers that resulted in excellent electrochemical sensing properties toward the detection of atropine (ATR), a substance that was found in beverages to facilitate sexual assault and other criminal acts. Linear range between 5 and 35 µmol L-1, detection limit of 1 µmol L-1, and adequate precision (RSD = 4.7%, n = 10) were achieved using differential-pulse voltammetry. The method was successfully applied to beverage samples with recovery values ranging from 80 to 105%. Interference studies in the presence of species commonly found in beverages confirmed satisfactory selectivity for ATR sensing. The devices proposed are useful portable analytical tools for on-site applications in the forensic scenario.

Prussian blue-modified laser-induced graphene platforms for detection of hydrogen peroxide.

A laser-induced graphene (LIG) surface modified with Prussian blue (iron hexacyanoferrate) is demonstrated as a novel electrochemical sensing platform for the sensitive and selective detection of hydrogen peroxide. Electrochemical Prussian blue (PB) modification on porous graphene films engraved by infrared laser over flexible polyimide was accomplished. Scanning electron microscopy images combined with Raman spectra confirm the formation of porous graphene and homogenous electrodeposition of PB over this porous surface. Electrochemical impedance spectroscopy reveals a substantial decrease in the resistance to charge transfer values (from 395 to 31.4 Ω) after the PB insertion, which confirms the formation of a highly conductive PB-graphene composite. The synergistic properties of PB and porous graphene were investigated for the constant monitoring of hydrogen peroxide at 0.0 V vs. Ag|AgCl|KCl(sat.), under high-flow injections (166 µL s-1) confirming the high stability of the modified surface and fast response within a wide linear range (from 1 to 200 µmol L-1). Satisfactory detection limit (0.26 µmol L-1) and selectivity verified by the analysis of complex samples confirmed the excellent sensing performance of this platform. We highlight that the outstanding sensing characteristics of the developed sensor were superior in comparison with other PB-based or LIG-based electrochemical sensors reported for hydrogen peroxide detection.

Affordable equipment to fabricate laser-induced graphene electrodes for portable electrochemical sensing.

Graphene-based materials present unique properties for electrochemical applications, and laser-induced conversion of polyimide to graphene is an emerging route to obtain a high-quality material for sensing. Herein we present compact and low-cost equipment constructed from an open-source 3D printer at which a 3.5-W visible (449 nm) laser was adapted to fabricate laser-induced graphene (LIG) electrodes from commercial polyimide, which resulted in electron transfer kinetic (k0) of 5.6 × 10-3 cm s-1 and reproducibility calculated by relative standard deviation (RSD < 5%) from cyclic voltammograms of [Fe(CN)6]3-/4- using 5 different electrodes. LIG electrodes enabled the simultaneous voltammetric determination of uric acid (+ 0.1 V vs. pseudo-reference) and nitrite (+ 0.4 V vs pseudo-reference), with limit of detection (LOD) values of 0.07 and 0.27 µmol L-1, respectively. Amperometric measurements for the detection of H2O2 (applying + 0.0 V vs. Ag|AgCl|KCl(sat.)) after Prussian blue (PB) modification and ciprofloxacin (applying + 1.2 V vs. Ag|AgCl|KCl(sat.)) were performed under flow conditions, which confirmed the high stability of LIG and LIG-PB surfaces. The LOD values were 1.0 and 0.2 µmol L-1 for H2O2 and ciprofloxacin, respectively. The RSD values (< 12%) obtained for the analysis using three different electrodes attested the precision of LIG electrodes manufactured in two designs. No sample matrix effects on the determination of ciprofloxacin in milk samples were observed  (recoveries between 84 and 96%). The equipment can be built with less than $300 and each LIG electrode costs less than $0.01.

Photobleaching Efficiency Parallels the Enhancement of Membrane Damage for Porphyrazine Photosensitizers.

Photostability is considered a key asset for photosensitizers (PS) used in medical applications as well as for those used in energy conversion devices. In light-mediated medical treatments, which are based on PS-induced harm to diseased tissues, the photoinduced cycle of singlet oxygen generation has always been considered to correlate with PS efficiency. However, recent evidence points to the fundamental role of contact-dependent reactions, which usually cause PS photobleaching. Therefore, it seems reasonable to challenge the paradigm of photostability versus PS efficiency in medical applications. We have prepared a series of Mg(II) porphyrazines (MgPzs) having similar singlet oxygen quantum yields and side groups with different electron-withdrawing strengths that fine-tune their redox properties. A detailed investigation of the photobleaching mechanism of these porphyrazines revealed that it is independent of singlet oxygen, occurring mainly via photoinduced electron abstraction of surrounding electron rich molecules (solvents or lipids), as revealed by the formation of an air-stable radical anion intermediate. When incorporated into phospholipid membranes, photobleaching of MgPzs correlates with the degree of lipid unsaturation, indicating that it is caused by an electron abstraction from the lipid double bond. Interestingly, upon comparing the efficiency of membrane photodamage between two of these MgPzs (with the highest and the lowest photobleaching efficiencies), we found that the higher the rate of PS photobleaching the faster the leakage induced in the membranes. Our results therefore indicate that photobleaching is a necessary step toward inflicting irreversible biological damage. We propose that the design of more efficient PS for medical applications should contemplate contact-dependent reactions as well as strategies for PS regeneration.

Encapsulation of metalloporphyrins improves their capacity to block the viability of the human malaria parasite Plasmodium falciparum.

Several synthetic metallated protoporphyrins (M-PPIX) were tested for their ability to block the cell cycle of the lethal human malaria parasite Plasmodium falciparum. After encapsulating the porphyrin derivatives in micro- and nanocapsules of marine atelocollagen, their effects on cultures of red blood cells infected (RBC) with P. falciparum were verified. RBCs infected with synchronized P. falciparum incubated for 48 h showed a toxic effect over a micromolar range. Strikingly, the IC50 of encapsulated metalloporphyrins reached nanomolar concentrations, where Zn-PPIX showed the best antimalarial effect, with an IC50=330 nM. This value is an 80-fold increase in the antimalarial activity compared to the antimalarial effect of non-encapsulated Zn-PPIX. These findings reveal that the incubation of P. falciparum infected-RBCs with 20 µM Zn-PPIX reduced the size of hemozoin crystal by 34%, whereas a 28% reduction was noticed with chloroquine, confirming the importance of heme detoxification pathway in drug therapy. FROM THE CLINICAL EDITOR: In this study, synthetic metalloporphyrins were tested as therapeutics that target Plasmodium falciparum. The IC50 of encapsulated metalloporphyrins was found to be in the nanomolar concentration range, with encapsulated Zn-PPIX showing an 80-fold increase in its antimalarial activity compared to the non-encapsulated form.

Novel disposable and portable 3D-printed electrochemical apparatus for fast and selective screening of 25E-NBOH in forensic samples.

The advent of new psychoactive substances (NPS) has caused enormous difficulty for legal control since they are rapidly commercialized, and their chemical structures are routinely altered. In this aspect, derivatives phenethylamines, such as 25E-NBOH, have received great attention in the forensic scenario. Hence, we propose portable and cost-effective (U$ 5.00) 3D-printed devices for the electrochemical screening of 25E-NBOH for the first time. The cell and all electrodes were printed using acrylonitrile butadiene styrene filament (insulating material) and conductive filament (graphite embedded in a polylactic acid matrix), respectively, both by the fused deposition modeling (FDM) 3D printing technique. The electrochemical apparatus enables micro-volume analysis (50-2000 µL), especially important for low sample volumes. A mechanistic route for the electrochemical oxidation of 25E-NBOH is proposed based on cyclic voltammetric data, which showed two oxidation processes around +0.75 V and +1.00 V and a redox pair between +0.2 and -0.2 V (vs. graphite ink pseudo-reference). A fast and sensitive square-wave voltammetry method was developed, which exhibited a linear working range from 0.85 to 5.1 µmoL-1, detection limit of 0.2 µmol L-1, and good intra-electrode precision (n = 10, RSD <5.3 %). Inter-electrode measurements (n = 3, RSD <9.8 %) also attested that the electrode production process is reproducible. Interference tests in the presence of other drugs frequently found in blotting paper indicated high selectivity of the electrochemical method for screening of 25E-NBOH. Screening analysis of blotting paper confirmed the presence of 25E-NBOH in the seized samples. Moreover, a recovery percentage close to 100 % was found for a spiked saliva sample, suggesting the method's usefulness for quantitative purposes aimed at information on recent drug use.

A novel 3D-printed graphite/polylactic acid sensor for the electrochemical determination of 2,4,6-trinitrotoluene residues in environmental waters.

Here, lab-made graphite and polylactic acid (Gpt-PLA) biocomposite materials were used to additively manufacture electrodes via the fused deposition modeling (FDM) technique for subsequent determination of the explosive 2,4,6-trinitrotoluene (TNT, considered a persistent organic pollutant). The surface of the 3D-printed material was characterized by SEM and Raman, which revealed high roughness and the presence of defects in the graphite structure, which enhanced the electrochemical response of TNT. The 3D-printed Gpt-PLA electrode coupled to square wave voltammetry (SWV) showed suitable performance for fastly determining the explosive residues (around 7 s). Two reduction processes at around -0.22 V and -0.36 V were selected for TNT detection, with linear ranges between 1.0 and 10.0 µM. Moreover, detection limits of 0.52 and 0.66 µM were achieved for both reduction steps. The proposed method was applied to determine TNT in different environmental water samples (tap water, river water, and seawater) without a dilution step (direct analysis). Recovery values between 98 and 106% confirmed the accuracy of the analyses. Additionally, adequate selectivity was achieved even in the presence of other explosives commonly used by military agencies, metallic ions commonly found in water, and also some electroactive camouflage species. Such results indicate that the proposed device is promising to quantify TNT residues in environmental samples, a viable on-site analysis strategy.

In need of a second-hand? The second coordination sphere of ruthenium complexes enables water oxidation with improved catalytic activity.

Artificial photosynthesis enables the conversion and storage of solar energy into chemical energy, producing substances with high energy content. In this sense, the oxidation of water can provide the H+ ions and electrons needed for the energy conversion and storage processes. Since 2005, it has been known that single-site coordination compounds can act as water oxidation catalysts (WOC). Improvement of the catalytic activity, however, has occurred mainly by the choice of the redox-active metal matching with a series of compatible ligands, more specifically, paying attention to the electronic characteristics of the organic framework of the first coordination sphere. Recently, the use of dangling bases dramatically increased the catalytic activity of new species as WOC, taking advantage of what is called a second coordination sphere. With this assistance, some compounds were shown to reach turnover frequencies (TOF) of 104 s-1, while compounds with the first coordination sphere commonly exhibit TOF ca. 10-1 s-1. In this manuscript, we discuss the concept, together with a number of examples, of the use of controlled interactions between the first and second coordination spheres that have been wielded to improve the performance of ruthenium-centered complexes as WOC in water oxidation reactions.

Effects of a strong π-accepting ancillary ligand on the water oxidation activity of weakly coupled binuclear ruthenium catalysts.

Significant differences were found in the proton-coupled redox chemistry and catalytic behavior of the binuclear [{Ru(H2O)(bpz)}2(tpy2ph)](PF6)4 complex [bpz = 2,2'-bipyrazine; tpy2ph = 1,3-bis(4'-2,2':6',2''-terpyridin-4-yl)benzene] as compared with the structurally analogous derivative with 2,2'-bipyridine (bpy) instead of bpz. The differences were assigned to the stronger π-accepting character of bpz relative to bpy as the ancillary ligand. The expectation of a positive shift for the Ru-centered redox potentials was confirmed for the lower oxidation state species, but that trend was reversed in the formation of the high-valence catalytic active species as shown by a negative shift of 0.14 V for the potential of the [RuIV/V[double bond, length as m-dash]O] process. Moreover, DFT calculations indicated a significant decrease of about 15% on the spin density and oxyl character of the [RuV[double bond, length as m-dash]O]3+ fragment. The significantly lower kcat(O2) for the bpz system was attributed to these combined electronic effects.

Thiosemicarbazone@Gold nanoparticle hybrid as selective SERS substrate for Hg2+ ions.

The Raman spectral profile of p-methylcarbohydrazonethioamide (MCHT) is completely changed due to strong SERS effects upon bonding onto gold nanoparticles surface, but some vibrational modes are further enhanced in the presence of Hg(II) ions. The lack of SERS response for most common metal ions indicates that the coordinating groups are interacting with the gold nanoparticles surface and not available for binding metal ions in solution, except for mercury ions. The selective enhancement of some vibrational modes is consistent with significant conformational changes upon binding of Hg(II) ion onto the AuNP@MCHT hybrid, as confirmed by TEM/EDS measurements, demonstrating its potentiality as a highly selective and sensitive SERS substrate.

Unexpected lability of the [RuIII(phtpy)Cl3] complex.

Ruthenium(iii) complexes are known for their high stability and inertness. To the best of our knowledge, the only well-characterized example of a labile Ru(iii) complex is [RuIII(edta)(H2O)] as a consequence of an intramolecular hydrogen bonding leading to the formation of a large opening in the molecule front, thus changing the mechanism from dissociative to associative. Compelling experimental evidence is presented demonstrating that the [RuIII(phtpy)Cl3] complex is labile, also indicating that the Ru(iii)-phtpy bond is much weaker than expected, in contrast to the strongly π-back-bonding stabilized Ru(ii)-phtpy bond.