Synergetic Exterior and Interfacial Approaches by Colloidal Carbon Quantum Dots for More Stable Perovskite Solar Cells Against UV.

The achievement of both efficiency and stability in perovskite solar cells (PSCs) remains a challenging and actively researched topic. In particular, among different environmental factors, ultraviolet (UV) photons play a pivotal role in contributing to device degradation. In this work, by harvesting simultaneously both the optical and the structural properties of bottom-up-synthesized colloidal carbon quantum dots (CQDs), a cost-effective means is provided to circumvent the UV-induced degradation in PSCs without scarification on their power conversion efficiencies (PCEs). By exploring and optimizing the number of CQDs and the different locations/interfaces of the solar cells where CQDs are applied, a synergetic configuration is achieved where the photovoltaic performance drop due to optical loss is completely compensated by the increased perovskite crystallinity due to interfacial modification. As a result, on the optimized configurations where CQDs are applied both on the exterior front side as an optical layer and at the interface between the electron transport layer and the perovskite absorber, unencapsulated PSCs with PCEs >20% are fabricated which can maintain up to ≈94% of their initial PCE after 100 h of degradation in ambient air under continuous UV illumination (5 mW cm-2).

Fabrication and Efficient Interfacial Assembly of Bright Red-Emitting Carbon Quantum Dots for Security-Warning Textiles.

Carbon quantum dots (CQDs) have attracted more attentions due to their multiple performances. However, the fabrication of long-wavelength emitting CQDs with aliphatic precursors still remains a challenge, mainly because it is difficult to generate large sp2 domains to reduce energy gap, which is not conducive to a redshift of the luminescence peak. Hereon, by regulating the pH of citric acid and thiourea mixture, a N, S co-doped CQD emitting bright red fluorescence at 635 nm is successfully fabricated through the solvothermal reaction under acidic condition, achieving a high quantum yield of 32.66%. Solvatochromic effects of the CQDs are discussed through theoretical equations and models, which confirm that the hydrogen-bonding interaction dominates the fluorescence emission behavior of CQDs in polar solvents. Besides, a feasible strategy is proposed to prepare an anti-counterfeiting textile via the deposition of red-emitting CQDs onto cotton fibers, through rapidly evaporating the preferred organic solvent. As expected, the CQD-decorated textiles exhibit encouraging anti-counterfeiting and security-warning functions, along with underwater and long-distance detectability, washability, and sun resistance. It is worth noting that the present work is innovative in realizing the application of red-light-emitting CQDs in the fields of security-warning textiles.

Isomerization Engineering of Oxygen-Enriched Carbon Quantum Dots for Efficient Electrochemical Hydrogen Peroxide Production.

Hydrogen peroxide (H2O2) has emerged as a kind of multi-functional green oxidants with extensive industrial utility. Oxidized carbon materials exhibit promises as electrocatalysts in the two-electron (2e-) oxygen reduction reaction (ORR) for H2O2 production. However, the precise identification and fabrication of active sites that selectively yield H2O2 present a serious challenge. Herein, a structural engineering strategy is employed to synthesize oxygen-doped carbon quantum dots (o-CQD) for the 2e- ORR. The surface electronic structure of the o-CQDs is systematically modulated by varying isomerization precursors, thereby demonstrating excellent electrocatalyst performance. Notably, o-CQD-3 emerges as the most promising candidate, showcasing a remarkable H2O2 selectivity of 96.2% (n = 2.07) at 0.68 V versus RHE, coupled with a low Tafel diagram of 66.95 mV dec-1. In the flow cell configuration, o-CQD-3 achieves a H2O2 productivity of 338.7 mmol gcatalyst -1 h-1, maintaining consistent production stability over an impressive 120-hour duration. Utilizing in situ technology and density functional theory calculations, it is unveil that edge sites of o-CQD-3 are facilely functionalized by C-O-C groups under alkaline ORR conditions. This isomerization engineering approach advances the forefront of sustainable catalysis and provides a profound insight into the carbon-based catalyst design for environmental-friendly chemical synthesis processes.

Paper based analytical devices for ions determination in nasal secretions demonstrating association with olfactory function.

Nasal ions environment plays a crucial role in maintaining nasal physiology and supports olfactory transmission. Addressing the limited research on nasal ion levels and their association with olfactory function, paper-based sensors were developed for determination of sodium, potassium, calcium and chloride in the nasal mucus of healthy volunteers and patients with olfactory dysfunction. Multi-walled carbon nanotubes and carbon quantum dots from beetroot were incorporated into paper substrate where sensors were designed with ion association complexes for sodium, potassium, calcium and chloride enhancing the recognition sensing capabilities. The sensors composition was optimized, including ion-exchange materials and plasticizers, to enhance sensitivity and selectivity. The performance of the sensors is evaluated based on Nernstian slope, dynamic range, detection limit and response time. Selectivity of the sensors was tested and the results demonstrated high selectivity for the target ions. The sensors were successfully determined sodium, potassium, calcium and chloride levels in nasal mucus of healthy volunteers and patients with olfactory dysfunction. The results revealed elevated calcium levels in patients with olfactory dysfunction, highlighting associated diagnostic implications. This suggests that the proposed sensors could serve as a diagnostic tool for olfactory evaluation, particularly in resource-constrained settings where access to advanced diagnostic tools is limited.

Biomass Derived Biofluorescent Carbon Dots for Energy Applications: Current Progress and Prospects.

Biomass resources are often disposed of inefficiently and it causes environmental degradation. These wastes can be turned into bio-products using effective conversion techniques. The synthesis of high-value bio-products from biomass adheres to the principles of a sustainable circular economy in a variety of industries, including agriculture. Recently, fluorescent carbon dots (C-dots) derived from biowastes have emerged as a breakthrough in the field, showcasing outstanding fluorescence properties and biocompatibility. The C-dots exhibit unique quantum confinement properties due to their small size, contributing to their exceptional fluorescence. The significance of their fluorescent properties lies in their versatile applications, particularly in bio-imaging and energy devices. Their rapid and straight-forward production using green/chemical precursors has further accelerated their adoption in diverse applications. The use of green precursors for C-dot not only addresses the biomass disposal issue through a scientific approach, but also establishes a path for a circular economy. This approach not only minimizes biowaste, which also harnesses the potential of fluorescent C-dots to contribute to sustainable practices in agriculture. This review explores recent developments and challenges in synthesizing high-quality C-dots from agro-residues, shedding light on their crucial role in advancing technologies for a cleaner and more sustainable future.

Synthesis of carbon quantum dots/porous aromatic frameworks (CQDs/PAF-45) composites and their enhanced photocatalytic performance.

Modification and functionalization of porous aromatic framework (PAF) materials have emerged as crucial research directions in various fields. In this study, we employed a hydrothermal method to synthesize a carbon quantum dots (CQDs) solution. By loading different amounts of CQDs onto the surface of PAF-45 material through ultrasonic and hydrothermal treatments, we successfully formed CQDs/PAF-45 composite materials. The introduction of CQDs effectively transformed the hydrophobic nature of PAF-45 into a hydrophilic material, thereby overcoming the challenge of achieving efficient contact between PAF catalysts and reactants in aqueous solutions. In the photocatalytic degradation experiments of Rhodamine B (RhB), tetracycline, CQDs/PAF-45 composite materials surpassed that of the pristine PAF-45 material. Notably, the 1 wt% CQDs/PAF-45 composite material exhibited the highest photocatalytic activity, with degradation efficiencies for Rhodamine B, tetracycline, and phenol approximately 1.4 times, 1.5 times and 1.5 times higher than those of the PAF-45 material, respectively.

Fluorometric Assay of Tyrosinase and Atrazine Based on the Use of Carbon Dots and the Inhibition of Tyrosinase Activity.

Sensitive and convenient strategy of tyrosinase (TYR) and its inhibitor atrazine is in pressing demand for essential research as well as pragmatic application. In this work, an exquisite label-free fluorometric assay with high sensitivity, convenience and efficiency was described for detecting TYR and the herbicide atrazine on the basis of fluorescent nitrogen-doped carbon dots (CDs). The CDs were prepared via one-pot hydrothermal reaction starting from citric acid and diethylenetriamine. TYR catalyzed the oxidation of dopamine to dopaquinone derivative which could quench the fluorescence of CDs through a fluorescence resonance energy transfer (FRET) process. Thus, a sensitive and selective quantitative evaluation of TYR can be constructed on the basis of the relationship between the fluorescence of CDs and TYR activity. Atrazine, a typical inhibitor of TYR, inhibited the catalytic activity of TYR, leading to the reduced dopaquinone and the fluorescence was retained. The strategy covered a broad linear range of 0.1-150 U/mL and 4.0-80.0 nM for TYR and atrazine respectively with a low detection limit of 0.02 U/mL and 2.4 nM/mL. It is also demonstrated that the assay can be applied to detect TYR and atrazine in spiked complex real samples, which provides infinite potential in application of disease monitoring along with environmental analysis.

o-phenylenediamine Derived Fluorescent Carbon Quantum dots for Detection of Hg(II) in Environmental Water.

With the expansion of human activities, the consequent influx of mercury (Hg) into the food chain and the environment is seriously threatening human life. Herein, nitrogen and sulfur co-doped fluorescent carbon quantum dots (yCQDs) were prepared via a hydrothermal method using o-phenylenediamine (OPD) and taurine as precursors. The morphological characteristics as well as spectral features of yCQDs indicated that the photoluminescence mechanism should be the molecular state fluorophores of 2, 3-diaminophenothiazine (oxOPD), which is the oxide of OPD. The as-synthesized yCQDs exhibited sensitive recognition of Hg2+. According to the investigation in combination of UV-Vis absorption spectra, time-resolved fluorescence spectra and quantum chemical calculations, the abundant functional groups on the surface of yCQDs allowed Hg2+ to bind with yCQDs through various interactions, and the formed complexes significantly inhibited the absorption of excitation light, resulting in the static fluorescence quenching of yCQDs. The proposed yCQDs was utilized for Hg2+ sensing with the limit of detection calculated to be 4.50 × 10- 8 M. Furthermore, the recognition ability of yCQDs for Hg2+ was estimated in tap water, lake water and bottled water, and the results indicated that yCQDs have potential applications in monitoring Hg2+.

Facile Synthesis of S-doped Carbon Quantum Dots and Their Application in the Detection of Sudan I in Saffron.

This study employed citric acid as a carbon source and thiourea as a sulphur source to conduct a straightforward one-step microwave synthesis of sulphur-doped carbon quantum dots (SCQDs). For the characterization of as-synthesized SCQDs, several methods such as fluorescence spectroscopy, X-Ray photoelectron spectroscopy (XPS), X-Ray diffraction (XRD), and zeta potential analyzer were utilized. XRD and XPS spectroscopy are used to examine the chemical composition and morphological aspects. These QDs have a limited size distribution spanning up to 5.89 nm, with a maximum distribution at 7 nm, according to zeta size analyser examinations. At an excitation wavelength of 340 nm, the highest fluorescence intensity (FL intensity) of SCQDs was attained. With a detection limit of 0.77 M, the synthesized SCQDs were employed as an efficient fluorescent probe for the detection of Sudan I in saffron samples.

A Fluorescence Biosensor Based on Carbon Quantum Dots Prepared from Pomegranate Peel and T-Hg2+-T Mismatch for Hg2+ Detection.

Mercury ions (Hg2+) can cause damage to human health, and thus, the study of the detection of Hg2+ is extraordinarily important in daily life. This work reported a fluorescence biosensor for the detection of Hg2+. The key point of this strategy was that the fluorescence of carbon quantum dots made from pomegranate peel (P-CQDs) was quenched by hemin, and restored after G-quadruplex binding with hemin. The presence of Hg2+ caused thymine (T)-rich DNA fragments to form T-Hg2+-T mismatches, and this change allowed the release of G-quadruplex. G-quadruplex could change the fluorescence of hemin/P-CQDs. P-CQDs exhibited excellent properties through characterization analysis, such as transmission electron microscope, X-ray photoelectron spectroscopy and Fourier transform infrared. This proposed fluorescence detection strategy established the linear ranges of Hg2+ from 1 nM to 50 nM. In conclusion, this simple biosensor had the advantages of strong sensitivity, high selectivity, and low cost for Hg2+ detection in environmental water samples.

Green Synthesis of CQDs via the Trunks of Bauhinia purpurea as Fluorescence Probes for Rapid and Accurate Detection of Quinoline Yellow.

Carbon quantum dots (CQDs) were greenly synthesized via a single-step hydrothermal method, using the trunks of Bauhinia purpurea as the carbon source. They exhibited good dispersibility, water solubility, high sensitivity, and great stability with a spherical form and a particle size of 2.68 ± 0.32 nm. By utilizing the inner filter effect and dynamic quenching effect, the fluorescence quenching of CQDs can be induced to detect quinoline yellow. Detailed experimental results showed that the change rate of fluorescence intensity of CQDs had a good linear relationship with varying concentrations of quinoline yellow (2-128 µmol/L). It can be clearly observed that the fluorescence quenching occurred within 1 min, its correlation coefficient (R2) is 0.9912, and the detection limit (DL) is 1.7884 µmol/L, substantially lower than the maximum concentration stipulated by the national standard of 209.5 µmol/L. Furthermore, quinoline yellow had been successfully detected in real beverage samples using CQDs, with the recovery rates of 90.6%-110.4% and the relative standard deviation (RSD) ≤ 6.3% and it also showed great anti-interference and selectivity. These findings indicate that the detected quinoline yellow of CQDs possess substantial promise for a wide range of applications within the detected artificial food colors field.

Synthesis of Bio-Base Fluorescence Carbon Dots for Selective Detection of Tartrazine and Sunset Yellow in Food Samples.

A green, economical and simple method for the preparation of water-soluble, high-fluorescent carbon quantum dots (CQDs) has been developed via hydrothermal process using pomelo peels as carbon source. The synthesized CQDs were characterized by transmission electron microscopy (TEM), X-ray diffraction(XRD), Fourier transform infrared spectroscopy (FTIR), UV - vis absorption spectra and fluorescence spectrophotometer. The results reveal that the as-prepared C-dots were spherical shape with an average diameter of 2.64 nm and emit bright blue photoluminescence (PL) with a quantum yield of approximately 3.63%. The surface of the C-dots was rich in hydroxyl groups and presented various merits including excellent photostability, low toxicity, and satisfactory solubility. Additionally, we found that two widely used synthetic food colorants, tartrazine and sunset yellow, could result in a strong fluorescence quenching of the C-dots, The possible mechanisms are caused by different ratios of inner filter and static quenching effects. According to this property, This study attempts to establish an analytical method for the determination of tartrazine and sunset yellow using carbon quantum dots as fluorescent probe. A linear relationship was found in the range of 0-100 µM tartrazine and sunset yellow with the detection limit(3σ/k) of 0.65 nM and 1.7 nM. The relative standard deviation (RSD) was 3.5% (tartrazine) and 3.0% (sunset yellow).This observation was further successfully applied for the determination of tartrazine and sunset yellow in food samples collected from local markets, and the recovery rates of the two ranges from 79% to 117.8 and 81 -103.5%, respectively. suggesting its great potential toward food routine analysis.

Preparation of Chiral Carbon Quantum Dots and its Application.

Chiral carbon quantum dots (cCQDs) , as a new type of carbon nano-functional material with tunable emission wavelength, superior photostability, low toxicity, biocompatibility and chirality, are playing an increasingly important role in the fields of chemistry, biology and medicine. This paper reviews the preparation methods (one-step and two-step), optical properties (UV, fluorescence, chirality) and applications in chiral catalysis, chiral recognition, targeted imaging as well as other fields, while lists some of the issues and challenges in the research of chiral carbon quantum dots. Finally, due to its good fluorescence and other properties, it is expected that chiral carbon quantum dots will have broad commercial prospects in future applications.

Natural Biowaste Derived Fluorescent Carbon Quantum Dots: Synthesis, Characterization and Biocompatibility Study.

In this present study, a straightforward and affordable method for the environmentally safe synthesis of carbon quantum dots (CQDs) by employing human hair as the carbon source without any need of chemicals was synthesized. CQDs obtained from human hair was further functionalized with Poly-L-Lysine to form PLLCQDs. The synthesized PLLCQDs was demonstrated numerous advantageous characteristics like strong fluorescence intensity, superior photostability, and outstanding water solubility. Various physicochemical characterization was employed to confirm successful formation of PLLCQDs including UV-vis Spectroscopy, Fluorescence Spectroscopy, Fourier Transform Infrared (FTIR) Spectroscopy, Atomic Force Microscopy (AFM) and Transmission Electron Microscopy (TEM). The size of synthesized PLLCQDs is 3 nm. The resultant PLLCQDs exhibited strong blue emission with a quantum yield of 28%. Under UV light, the synthesized PLLCQDs emit blue (at 365nm) fluorescence. The optimization of synthesis parameters including synthesis method, effect of reaction temperature, effect of reaction time and effect of reaction concentration have a significant impact on the quality and quantity of synthesized PLLCQDs, as well as their properties and applications. The effect of pH and UV radiation on synthesized PLLCQDs exhibited excellent photo and chemical stability. The cytotoxicity of bulk system (Hair precursor) and PLLCQDs was evaluated using fibroblast cell line (L929). The cell viabilities of 99.47% was obtained from L929 cells using MTT assay and it can applicably function as agents for cell labelling as a good bioimaging probe.

A Simple Method for Synthesizing Nitrogen-Doped Carbon Quantum Dots for Fluorescent "Turn off" Mercury (II) Ion Sensing.

Here, straightforward and environmentally friendly fluorescent nitrogen doped carbon quantum dots (N-CQDs) with a high blue fluorescence emission at 455 nm are used for ultrasensitive Hg2+ ion detection. Folic acid and urea are used as carbon sources in the carbonization process. Two broad absorption bands at around 280 and 370 nm from UV-Vis spectrum and characteristic absorption peaks from infrared spectrum confirms the successful synthesis of the N-CQDs. Energy dispersive X-Ray analysis confirmed the elemental composition of the N-CQDs. Transmission electron microscopy showed the homogeneous globular morphology of the N-CQDs with an average particle size of 65 nm. Zeta potential measurement established the stability and surface charge of N-CQDs. Dynamic light scattering measurement showed the average size of N-CQDs. With the addition of Hg2+ ion to N-CQDs, the blue fluorescence emission is quenched. Moreover, the N-CQDs can be applied to real water sample such as pond water, river water, and tap water. The detection limit is approximately calculated to be 12 nM and linear range is 0-30 parts per billion.

Functionalized Green Carbon dots for Specific Detection of Copper in Human Serum Samples and Living Cells.

Intracellular copper ion (Cu2+) is irreplaceable and essential in regulation of physiological and biological processes, while excessive copper from bioaccumulation may cause potential hazards to human health. Hence, effective and sensitive recognition is urgently significant to prevent over-intake of copper. In this work, a novel highly sensitive and green carbon quantum dots (Green-CQDs) were synthesized by a low-cost and facile one-step microwave auxiliary method, which utilized gallic acid, carbamide and PEG400 as carbon source, nitrogen source and surface passivation agent, respectively. The decreased fluorescence illustrated excellent linear relationship with the increasing of Cu2+ concentration in a wide range. Substantial surface amino and hydroxyl group introduced by PEG400 significantly improved selectivity and sensitivity of Green-CQDs. The surface amino chelation mechanism and fluorescence internal filtration effect were demonstrated by the restored fluorescence after addition of EDTA. Crucially, the nanosensor illustrated good cell permeability, high biocompatibility and recovery rate, significantly practical application in fluorescent imaging and biosensing of intracellular Cu2+ in HepG-2 cells, which revealed a potential and promising biological applications in early diagnosis and treatment of copper ion related disease.

Turn-Off Fluorescence Sensor for the Detection of Ferric Ion in Water Using Green Synthesized Wrightia coccinea Carbon Quantum Dot.

The current study report that the production of carbon quantum dots from Wrightia coccinea (WC) leaves using an eco-friendly, one-pot process. The structural, morphological, and optical characteristics of the CDs made from W. coccinea leaves by hydrothermal treatment at 200 °C for six hours were assessed using a variety of spectroscopic and electron microscopy techniques. The average size of CD was found to be approximately 5 nm using transmission electron microscopy (TEM) and the quantum yield of the produced CD was 15.6%. The synthesized CDs demonstrated extraordinary sensing capacity with a detection limit of 0.511 µM for ferric ion detection. The impact of varying pH levels on the fluorescence behavior of CD was thoroughly investigated. The maximum fluorescence intensity was examined at pH 3. Therefore, to detect Fe3+ ions as best as possible, the pH of the entire solution was adjusted to a value of 3. Furthermore, the pH-dependent fluorescence feature of CDs can be exploited by pH-sensitive fluorescence sensors. In the future, this might provide an added advantage for pH-based fluorescence sensor applications.

A Dual-Mode Spectrophotometric and Fluorescent Probe Based on Lignin-Derived Carbon Dots for the Detection of Atorvastatin Calcium in a Bulk Powder and a Commercial Product.

Recently, dual-mode techniques have garnered considerable attention and have been shown to be effective approaches for biomedical analysis and environmental monitoring. A novel and simple dual-mode spectrophotometric and fluorometric probe based on lignin-derived carbon dots (LCDs) was developed to detect atorvastatin calcium (ATS) in a bulk powder and its commercial product. The synthesized LCDs exhibit exceptional fluorescence characteristics and are highly soluble in water while maintaining reasonable stability. The average particle size of the LCDs was 3.42 ± 1.03 nm. The characterization of the produced LCDs indicated a structure resembling graphene oxide with the presence of several functional groups. The developed LCDs show a good fluorescence quantum yield of 32.2%. The fluorescence of the LCDs is quenched by ATS at an emission wavelength of 315 nm after excitation at 275 nm through dynamic and static quenching mechanisms. The optimal reaction conditions for the dual-mode reaction were a pH of 9 and 0.05 mL of the LCDs, which were measured after 3 min at 30 °C by spectrophotometry, followed by 7 min at 20 °C by fluorometric methods. According to the spectrophotometric results, the response of ATS was linear in the range of 4.0-100.0 µg/mL, while according to the fluorometric results, the dynamic range was 3.0-50.0 µg/mL. The limits of detection (LODs) and the limits of quantification (LOQs) were 0.97 µg/mL and 2.95 µg/mL for the fluorometric method, respectively. The nanoprobe effectively analyzed ATS in medication samples and yielded good results.

Green Synthesis of Carbon Quantum dots Derived from Lycium barbarum for Effective Fluorescence Detection of Cr (VI) Sensing.

Green and economical self-doped nitrogen-containing fluorescent carbon quantum dots (N-CQDs) were synthesized using a one-pot hydrothermal treatment method. The optical and structural properties of the N-CQDs were investigated in detail by UV-vis and fluorescence spectroscopy, X-ray diffraction (XRD) techniques, transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) spectroscopy, and elemental analysis illustrate the surface function and composition of N-CQDs. N-CQDs emit a broad fluorescence between365 Ì´ 465 nm and fluoresce most strongly at the excitation wavelength of 415 nm. Meanwhile, Cr (VI) could significantly burst the fluorescence intensity of N-CQDs. N-CQDs showed an excellent sensitivity and selectivity to Cr (VI), which exhibited good linearity in the range of 0 Ì´ 40 µmol/L with a detection limit of 0.16 µmol/L. In addition, the mechanism of Fluorescence quenching of N-CQDs by Cr (VI) was investigated. This work well provides a research idea for the preparation of green carbon quantum dots from biomass and their use for the detection of metal ions.

Microwave Synthesis of Fluorescent Carbon Quantum dots from Araucaria Heterophylla Gum: Application in Drug Detection.

This study employed a green microwave synthesis technique to produce carbon quantum dots (CQDs) from araucaria heterophylla gum extract. The produced CQDs emit a distinct blue fluorescent light, contributing a remarkable quantum yield of 14.69%. Their average particle size measures at 1.62 ± 0.39 nm. Furthermore, these CQDs demonstrate excellent water solubility and maintain high fluorescence stability despite ionic strength, pH and time variations. Moreover, we present here for the first time that the synthesized CQDs demonstrate a rapid, exceptionally sensitive, and discerning fluorescence quenching phenomenon (IFE) concerning Cefprozil (CPR). The fluorescent probe was sensitive and specific with good linear relationships for CPR in the 0-18 µM range. The limit of detection for relationships for CPR was 2.51 µM. This study provides novel opportunities for producing high-quality luminescent CQDs that meet the requirements for various biological and environmental applications.