Effect of multiple firings on optical and mechanical properties of Virgilite-containing lithium disilicate glass-ceramic of varying thickness.

OBJECTIVES: To investigate the effect of multiple firings on color, translucency, and biaxial flexure strength of Virgilite-containing (Li0.5Al0.5Si2.5O6) lithium disilicate glass ceramics of varying thickness. MATERIALS AND METHODS: Sixty discs were prepared from Virgilite-containing lithium disilicate blocks. Discs were divided according to thickness (n = 30) into T0.5 (0.5 mm) and T1.0 (1.0 mm). Each thickness was divided according to the number of firing cycles (n = 10); F1 (Control group): 1 firing cycle; F3: 3 firing cycles, and F5: 5 firing cycles. The discs were tested for color change (ΔE00) and translucency (TP00) using a spectrophotometer. Then, all samples were subjected to biaxial flexure strength testing using a universal testing machine. Data were collected and statistically analyzed (α = 0.5). For chemical analysis, six additional T0.5 discs (2 for each firing cycle) were prepared; for each firing cycle one disc was subjected to X-ray diffraction analysis (XRD) and another disc was subjected to Energy dispersive X-ray spectroscopy (EDX) and Scanning electron microscope (SEM). RESULTS: Repeated firing significantly reduced the translucency of F3 and F5 compared to F1 in T0.5 (p < 0.001), while for T1.0 only F5 showed a significant decrease in TP00 (p < 0.001). For ΔE00, a significant increase was recorded with repeated firings (p < 0.05) while a significant decrease resulted in the biaxial flexure strength regardless of thickness. CONCLUSIONS: Repeated firings had a negative effect on both the optical and mechanical properties of the Virgilite-containing lithium disilicate glass ceramics. CLINICAL RELEVANCE: Repeated firings should be avoided with Virgilite-containing lithium disilicate ceramics to decrease fracture liability and preserve restoration esthetics.

Effect of aging and fiber-reinforcement on color stability, translucency, and microhardness of single-shade resin composites versus multi-shade resin composite.

OBJECTIVE: The purpose of this study was to evaluate the effect of aging and fiber-reinforcement on the color stability, translucency, and microhardness of single-shade resin composites versus multi-shade resin composite. MATERIALS AND METHODS: Four resin composites (Filtek Z250, Omnichroma, Vittra APS Unique, Zenchroma) were tested. Three subgroups of specimens were prepared for each of the composites: control, polyethylene fiber-reinforcement, and glass fiber-reinforcement- groups (n = 10/per group). The samples were subjected to aging for 10,000 thermal cycles. Color differences (ΔE00 ) were calculated after aging. Relative translucency parameter (RTP00 ) and microhardness values were calculated before and after aging. A two-way analysis of variance and the generalized linear model was used (p < 0.05). RESULTS: The lowest and highest ΔE00 values were found for Filtek Z250 (0.6 ± 0.2) and Omnichroma resin composites (1.6 ± 0.4), respectively. The ΔE00 value of the polyethylene fiber-reinforcement group (1.2 ± 0.6) was significantly higher than the ΔE00 value of the glass fiber-reinforcement group (1.0 ± 0.4, p < 0.001). The RTP00 value of the glass fiber-reinforcement group (1.92 ± 0.78) was significantly higher than the RTP00 value of the polyethylene fiber-reinforcement group (1.72 ± 0.77, p < 0.001). The highest microhardness values were found in glass fiber-reinforcement group (76.48 ± 17.07, p < 0.001). CONCLUSION: Single-shade resin composites were more translucent, had higher color change, and lower hardness than multi-shade resin composite. For relative translucency and microhardness, statistical significance was found in the material and fiber type interaction. The glass fiber-reinforcement provided higher translucency, lower color change and higher microhardness values than polyethylene fiber-reinforcement group after aging. Thermocycling had a significant impact on the color stability, translucency parameter, and microhardness of the tested resin composite materials. CLINICAL SIGNIFICANCE: Single-shade resin composite materials have greater color-changing potential. The glass fiber-reinforcement optimize resin material mechanical properties and color stability more than polyethylene fiber-reinforcement.

Color stability of bleached tooth enamel brushed with different stain-removing toothpastes.

OBJECTIVE: The effects of four toothpastes on the color stability of in-office bleached tooth specimens were determined. MATERIALS AND METHODS: We evaluated an experimental toothpaste (EXP) and three commercially available toothpastes: Colgate Optic White (OPW), Aquafresh White & Protect (AWP), and Crest 3D White (CDW). OPW, AWP, and CDW contained inorganic abrasives, whereas EXP and AWP contained sodium polyphosphate. Forty-eight randomly selected human-extracted maxillary central incisors were bleached and brushed twice daily over 30 days. We analyzed the final color difference (ΔE*ab, ΔE00 , ΔWID ), arithmetic average surface roughness (Ra) of the enamel measured on days 0 and 30, and scanning electron microscopy images of enamel surfaces and toothpastes. ΔE*ab, ΔE00 , ΔWID , and Ra were analyzed using one-way analysis of variance and Tukey's test (α = 0.05). RESULTS: ΔE*ab and ΔE00 values were significantly lower after toothbrushing with EXP, OPW, and CDW than with AWP. OPW induced the greatest positive ΔWID . Ra was significantly increased by OPW and CDW, but slightly increased by AWP, with cube-like particles, and EXP, with no particle-like structures. CONCLUSIONS: Only EXP stabilized the color of bleached teeth without increasing the enamel surface roughness. Sodium polyphosphate with approximately 10 phosphate groups was effective at removing stains. CLINICAL SIGNIFICANCE: The effect of toothpaste on the color stability of bleached teeth depends on the constituting abrasives and chemical components. Polyphosphoric acid has different stain-removal effects depending on its degree of polymerization. Additionally, although certain types of abrasives may be effective for color stability, they also increase the surface roughness of the enamel.

Chitosan/Polyvinyl Alcohol-Based Biofilms Using Ternary Deep Eutectic Solvents towards Innovative Color-Stabilizing Systems for Anthocyanins.

Anthocyanins are amazing plant-derived colorants with highly valuable properties; however, their chemical and color instability issues limit their wide application in different food industry-related products such as active and intelligent packaging. In a previous study, it was demonstrated that anthocyanins could be stabilized into green plasticizers namely deep eutectic solvents (DESs). In this work, the fabrication of edible films by integrating anthocyanins along with DESs into biocompatible chitosan (CHT)-based formulations enriched with polyvinyl alcohol (PVA) and PVA nanoparticles was investigated. CHT/PVA-DES films' physical properties were characterized by scanning electron microscopy, water vapor permeability, swelling index, moisture sorption isotherm, and thermogravimetry analysis. Innovative red-to-blue formulation films were achieved for CHT/PVA nanoparticles (for 5 min of sonication) at a molar ratio 1:1, and with 10% of ternary DES (TDES)-containing malvidin-3-glucoside (0.1%) where the physical properties of films were enhanced. After immersion in solutions at different pH values, films submitted to pHs 5-8 were revealed to be more color stable and resistant with time than at acidic pH values.

Influence of in-office whitening on the color matching and surface characteristics of single-shade resin composites.

OBJECTIVE: The color matching of single-shade resin composites after in-office whitening was investigated. MATERIALS AND METHODS: Four single-shade resin composites were used. A total of 35% hydrogen peroxide was used as the whitening agent. The resin composite was placed in a cavity of an artificially discolored bovine tooth. The color differences between the restoration and surrounding enamel before and after whitening were determined based on ΔE*ab, ΔE00, and ΔWID. The color stability, surface roughness (Sa), and surface gloss (GU) of the resin composite alone were also evaluated. Statistical analyses were performed using repeated-measures analysis of variance with the Tukey-Kramer test. RESULTS: Based on the 50:50% of perceptibility and acceptability thresholds of ΔE*ab and ΔE00, none of the resin composite restorations were clinically acceptable before or after whitening. Regarding ΔWID, although all resin composites showed "acceptable match" in the baseline, they showed "mismatch" after the third session of whitening. Most of the resin composites alone were stable in color against whitening. CONCLUSIONS: Although the single-shade resin composites failed to achieve the expected color matching on discolored teeth either before or after the whitening, the impact of the whitening on the color of the resin composite alone may be negligible.

Semisynthesis of Betaxanthins from Purified Betacyanin of Opuntia dillenii sp.: Color Stability and Antiradical Capacity.

The availability of pure individual betalains in sufficient quantities which permit deeper understanding is still a challenge. This study investigates the high-yielding semisynthesis of betaxanthins using betalamic acid from a natural source (Opuntia dillenii), followed by condensation with ʟ-amino acids and further purification. Moreover, the color stability of the four synthesized individual betaxanthins, namely proline (ʟ-ProBX), alanine (ʟ-AlaBX), leucine (ʟ-LeuBX), and phenylalanine (ʟ-PheBX) betaxanthins, was investigated at different pHs. Their relative contribution to free radical scavenging was also scrutinized by TEAC and DPPH. ʟ-AlaBX and ʟ-LeuBx showed a significantly (p < 0.05) higher antioxidant activity, whereas ʟ-ProBX was the most resistant to the hydrolysis of betaxanthin and hence the least susceptible to color change. The color stability was strongly influenced by pH, with the color of ʟ-ProBX, ʟ-LeuBX, and ʟ-AlaBX at pH 6 being more stable, probably due to the easier hydrolysis under acid conditions. The semisynthesis and purification allowed us to have available remarkable quantities of pure individual betaxanthins of Opuntia dillenii for the first time, and to establish their color properties and antioxidant capacity. This study could be a step forward in the development of the best natural food colorant formulation, based on the betalain structure, which is of special interest in food technology.

A review on improving the sensitivity and color stability of naturally sourced pH-sensitive indicator films.

Naturally sourced pH-sensitive indicator films are of interest for real-time monitoring of food freshness through color changes because of their safety. Therefore, natural pigments for indicator films are required. However, pigment stability is affected by environmental factors, which can in turn affect the sensitivity and color stability of the pH-sensitive indicator film. First, natural pigments (anthocyanin, betalain, curcumin, alizarin, and shikonin) commonly used in pH-sensitive indicator films are presented. Subsequently, the mechanisms behind the change in pigment color under different pH environments and their applications in monitoring food freshness are also described. Third, influence factors, such as the sources, types, and pH sensitivity of pigments, as well as environmental parameters (light, temperature, humidity, and oxygen) of sensitivity and color stability, are analyzed. Finally, methods for improving the pH-sensitive indicator film are explored, encapsulation of natural pigments, incorporation of a hydrophobic film-forming matrix or function material, and protective layer have been shown to enhance the color stability of indicator films, the addition of copigments or mental ions, blending of different natural pigments, and the utilization of electrospinning have been proved to increase the color sensitivity of indicator films. This review could provide theoretical support for the development of naturally sourced pH-sensitive indicator films with high stability and sensitivity and facilitate the development in the field of monitoring food freshness.

Effect of conventional cigarette smoking and recent heated tobacco products on CAD/CAM restorative materials.

OBJECTIVE: To determine the effects of conventional cigarette smoking (CS) and recent heated tobacco products (HTPs) on the surface roughness and color stability of different indirect restorative materials. MATERIALS AND METHODS: One hundred disc-shaped samples were constructed of three different restorative CAD/CAM materials: lithium disilicate glass-ceramic (IPS e.max CAD; Ivoclar Vivadent, Liechtenstein), zirconia (BruxZir® Zirconia, Glidewell, USA) and polyetheretherketone (BioHPP® bredent GmbH, Germany). Of the IPS e.max CAD and the Bruxzir samples, 20 samples were glazed, and 20 samples were polished, while the BioHPP samples were all polished according to the manufacturer's instructions. Fifty samples were subjected to conventional cigarette smoking (LM, Philip Morris International Inc., Egypt) (Groups: IPS e.max CAD_Glazed exposed to CS (LD_G_Cig), IPS e.max CAD_Polished exposed to CS (LD_P_Cig), Bruxzir_Glazed exposed to CS (Zr_G_Cig), Bruxzir _Polished exposed to CS (Zr_P_Cig) and BioHPP exposed to CS (PEEK_Cig) and fifty samples were exposed to heated tobacco product smoking (Heets, Russet selection, Philip Morris International Inc., Italy) (Groups: IPS e.max CAD_Glazed exposed to HTP (LD_G_HTP), IPS e.max CAD_Polished exposed to HTP (LD_P_HTP), Bruxzir_Glazed exposed to HTP (Zr_G_HTP), Bruxzir CAD_Polished exposed to HTP (Zr_P_HTP) and BioHPP exposed to HTP (PEEK_HTP).. Six hundred cigarettes/heets representing 30 days of medium smoking behavior (20 cigarettes/day) were used. Before and after exposure to smoke, the surface roughness of all the samples was measured using JITAI8101 surface roughness tester (Beijing Jitai Tech Detection Device Co., Ltd, China, and the color parameters were assessed using VITA Easyshade Advance 4.01 (VITA shade, VITA made, VITA). The data were analyzed using One-way ANOVA, paired sample t-test and independent sample t-test. The significance level was set at α < 0.05. The surface topography was evaluated by scanning electron microscopy (SEM) and analyzed using energy-dispersive X-ray (EDX) spectroscopy to determine changes in the surface chemical composition. RESULTS: Both types of smoking caused significant increases in the surface roughness of all the samples. There was a significant difference in color change between CS and HTP for all materials with different surface finish (P < 0.01) and zirconia had the greatest effect on color change (P < 0.001). In contrast, polyetheretherketone (PEEK) "BioHPP" had the least effect (P < 0.001). CONCLUSION: Exposure to different types of smoking induce changes in the surface topography and color of different esthetic restorative materials. Compared with HTP, conventional cigarette smoke has a greater effect on the surface roughness and color stability of esthetic restorative materials. The glazed surfaces showed less change in surface topography than did the polished surfaces. Zirconia showed better color stability when compared to polyetheretherketone (PEEK).

Comparison of light transmittance and color changes between polyurethane and copolyester retainer materials after staining and destaining.

BACKGROUND: Retainers are the only effective approach to prevent orthodontic relapse. The aim of this study was to compare the changes in color and light-transmittance of rough and smooth thermoformed polyurethane and copolymer retainer samples after staining in different solutions and destaining with different approaches. METHODS: Four hundred copolyester (Essix® ACE) and 400 polyurethane (Zendura®) samples with different surface textures, smooth and rough, were stained in 4 different solutions (n = 100 per solution) over 28 days. Each of the four groups of 100 stained samples of each material was subdivided into 5 groups of 20 samples and subjected to different destaining solutions. Light transmittance and color changes were evaluated using a spectrometer and a spectrophotometer. Mean differences were compared using a two-way analysis of variance (ANOVA) and posthoc multiple comparison tests at P = 0.05. RESULTS: No significant differences in light transmittance were found between both untreated materials. Both materials were stained in a similar fashion and showed no significant differences between two materials after staining. Coffee and tea stained both materials more significantly than wine, but there was a significant difference of changes of color and light transmittance between rough and smooth surfaces during the destaining in coffee- and tea-stained samples of copolyester material. All destaining solutions were effective at removing all stains on the samples. The surface roughness of the material plays a significant role in the ability of the materials to be destained, demonstrating a more significant greater effect on cleaning rough samples for improvements in light-transmittance and greater changes in color. CONCLUSIONS: This study concluded that the surface of materials plays a significant role in the material destaining and staining. In addition, the different polymers used for retainer fabrication exhibited different responses during the destaining process depending on types of stains.

The effect of various inhaled asthma medications on the color stability of paediatric dental restorative materials.

BACKGROUND: The purpose of the study is to analyse the effects of different inhaled asthma medications (IAMs) on the color change of dental restorative materials (DRMs). METHODS: In total, 192 samples were taken from six different DRMs: [Filtek Z550 (nanohybrid composite), Fusio Liquid Dentin (Self-adhering flowable composite), Filtek Ultimate (nanofilled flowable composite), Dyract XP (compomer), Fuji II LC (resin-modified glass ionomer), Fuji IX Fast (self-cured-packable glass ionomer), (n = 32)]. After the initial color values (CIELab) of DRMs were measured by using a spectrophotometer, each sample was exposed to the same IAMs via nebulizer according to the four different inhaled therapies and measurements were repeated on the 7th & 21st days. RESULTS: In all IAM groups, DRM with the least amount of ΔE was nanohybrid composite, while the highest ΔE was found in Fuji II LC. Among all experimental groups, only Fuji II LC which was administered the combined medication, exceeded the clinically unacceptable threshold (ΔE = 3.3) on 7th & 21st days. CONCLUSIONS: Consequently, important factors affecting the susceptibility to color stability are the type of IAMs, the administration time-dosage, and the type of DRMs.

The effect of whitening toothpastes on the color stability and surface roughness of stained resin composite.

BACKGROUND: This study aimed to investigate the effect of whitening toothpastes on the color stability and surface roughness of resin composites stained with coffee and cigarette smoke. METHODS: Seventy-two disk-shaped specimens (6 × 2 mm) of suprananohybrid resin composite were randomly divided into two groups and exposed to coffee and cigarette smoke (n = 36). After staining, the samples randomly divided into four groups according to whitening toothpastes and were brushed for 4 min: Opalescence Whitening (OW); Colgate Optic White (COW); Curaprox Black is White (CPX) and, distilled water (control) (n = 9). Color was measured with spectrophotometer at the initial, after staining, and after brushing, and surface roughness was measured with profilometer at the initial and after brushing. A surface morphology analysis was examined using scanning electron microscopy and atomic force microscopy. The obtained data were statistically analyzed. (p < 0.05). RESULTS: Cigarette smoke caused a significantly higher color change than coffee in the resin composite (p < 0.05). Brushing with hydrogen peroxide and silica-containing whitening toothpaste showed significant differences in color change (p < 0.05). The lowest whitening effect was found in activated charcoal-containing toothpaste. While all toothpastes increased the degree of surface roughness of resin composites, the highest roughness was caused by whitening toothpastes containing activated charcoal. (p < 0.05). CONCLUSIONS: The color stability and surface properties of resin composites can be affected by brushing them with whitening toothpaste. The utilization of whitening toothpaste containing hydrogen peroxide can be considered a safe method for increasing the whiteness of discolored resin composites.

Color stability of dual-cured and light-cured resin cements: A systematic review and meta-analysis of in vitro studies.

PURPOSE: This systematic review and meta-analysis aimed to evaluate the difference in the color stability of light-cured and dual-cured resin cements. MATERIALS AND METHODS: Two separate reviewers used the PubMed, Scopus, Web of Science, Embase, and Scielo databases to execute the systematic review. For the analysis, studies that evaluated the color stability of dual-cured and light-cured resin cements over time were used. The random effects model was used in the meta-analysis. Analyses of subgroups were carried out based on the aging technique. The methodological quality of each in vitro study was evaluated in accordance with the parameters of a prior systematic review. RESULTS: From all databases, a total of 2223 articles were retrieved. Following the screening of titles and abstracts, 44 studies were selected for full text review, and a total of 27 articles were used for the qualitative analysis. Finally, 23 articles remained for the qualitative analysis. The majority of studies were labeled as having a medium risk of bias. The global analysis showed that the dual-cure resin cements had considerably greater differences in the color change (p = 0.006). A high heterogeneity index (86%) was found in the analysis. CONCLUSIONS: The best available in vitro evidence suggests that dual-polymerizing cement has higher color variation than light-polymerized materials. To reduce the likelihood of color change after the luting of thin ceramic restorations, clinicians should employ light-polymerizable resin cements.

Color stability of precolored and extrinsically colored monolithic multilayered polychromatic zirconia: Effects of surface finishing and aging.

PURPOSE: To explore the impact of zirconia types, coloring methods, and surface finishing on the color stability of monolithic multilayered polychromatic zirconia after artificial aging, including thermocycling and simulated toothbrushing. MATERIALS AND METHODS: Eighty square-shaped zirconia samples were divided into 2 types (M3Y-TZP and M6Y-PSZ), further categorized based on coloring methods (precolored and extrinsically colored) and surface finishing techniques (mechanical polishing or glazing). The color stability was assessed using the CIEDE2000 formula. Artificial aging was simulated via thermocycling and toothbrushing. All samples were analyzed with a spectrophotometer to determine the post-aging color changes (ΔE00). The ΔE00 were interpreted and classified using the 50:50% perceptibility threshold (PT) and the 50:50% acceptability threshold (AT). Comparisons between groups for ΔE00 differences were performed using three-way ANOVA, with pairwise comparisons facilitated by Fisher's protected least significant difference test, α = 0.05. RESULTS: The study results indicated significant impacts of zirconia type, coloring method, and surface finishing on color stability. The M6Y groups experienced significantly greater color changes (6.61 ± 1.63) compared to the M3Y groups (3.40 ± 2.24), p < 0.0001. For both types of zirconia, extrinsically colored samples exhibited significantly higher ΔE00 when mechanically polished (p = 0.004). However, surface finishing had no significant effect on ΔE00 in precolored samples of either zirconia material (p = 1.000). The evaluation and categorization of ΔE00 variations indicated that nearly all color changes in the M6Y groups, regardless of being precolored, extrinsically colored, polished, or glazed, were deemed extremely unacceptable (Grade 1). In contrast, the M3Y groups showed more acceptable results, with the majority of color changes classified as moderately unacceptable (Grade 3). CONCLUSIONS: The color stability of multilayered polychromatic zirconia is influenced by the type of material, extrinsic coloring, and the chosen surface treatment post-artificial aging. The translucent 6Y-PSZ exhibited lower color stability, especially with only mechanical polishing. For the fabrication of M3Y-TZP and 6Y-PSZ monolithic multilayered polychromatic zirconia restorations, extrinsic coloring should be paired with glazing to maintain color stability. Conversely, in the absence of extrinsic coloring, both glazing and mechanical polishing are effective in preserving color stability.

The effect of pediatric drugs on color stability of bulk-fill and conventional composite resins.

The long-term use of pediatric medications can lead to discoloration of dental restorations, which affects their durability and longevity. The present in vitro study evaluated the effects of commonly used pediatric medications on the color stability of a conventional and a bulk-fill composite resin. For this study, 80 disc-shaped specimens of each composite were prepared in molds with a diameter of 6 mm and thicknesses of 2 or 4 mm (n = 40 per thickness per material). A spectrophotometer was used to evaluate the baseline color of the specimens in the International Commission on Illumination L*a*b* color space. Each specimen was immersed separately in a container holding 1 of 8 liquid medications (n = 5 per thickness per medication): amoxicillin/clavulanate, clarithromycin, cephalexin, acetaminophen, ibuprofen, levetiracetam, multivitamin, or albuterol. After the container was shaken for 2 minutes, the specimen was removed from the medication and stored in artificial saliva. The cycle was repeated every 8 hours for 1 week. The color measurements were repeated after 1 week of immersion cycles, and the overall color change (ΔE*) was calculated; a value of ΔE* > 3.3 was considered clinically perceptible. The data were analyzed with 1-way and 2-way analyses of variance as well as the Levene test and Games-Howell post hoc test (P < 0.05). All specimens displayed clinically perceptible color changes after exposure to medications commonly used by children. The mean color change in the 4-mm bulk-fill composite resin group was significantly greater than that in all other groups (P < 0.05). However, there was no significant difference in color change based on the immersion drug for either of the composites (P > 0.05). The study findings show that exposure of composite resin to certain commonly used pediatric drugs causes color changes that are clinically perceptible.

Evaluating the color stability of temporary crowns fabricated by 3-dimensional printing and manual methods.

This in vitro study aimed to compare the color stability of temporary crowns fabricated by 3-dimensional (3D) printing with that of crowns fabricated with 2 manual methods. An impression was made of a prepared central incisor, from which 90 dies were fabricated. The dies were randomly assigned to 3 groups (n = 30) based on crown fabrication method: 3D printing, automix bis-acryl resin, or powder-and-liquid polymethyl methacrylate. All specimens were immersed in a coffee, soft drink, or distilled water solution for 1 week (n = 10 per subgroup). Color change was measured using a spectrophotometer and the International Commission on Illumination's CIE L*a*b* method, and the values were converted to the National Bureau of Standards (NBS) index for assessment and comparison. When color change was assessed according to fabrication method, the highest (mean [SD]) ΔE* value was reported for the automix specimens (3.39 [2.86]), and the lowest was recorded for the powder-and-liquid specimens (2.05 [2.33]) (P < 0.05; Kruskal-Wallis test). The difference between ΔE* values of the 3D printing group (2.46 [1.75]) and the powder-and-liquid group was not statistically significant. When color change was assessed according to the immersion solution, the coffee solution showed a significantly higher (mean [SD]) ΔE* value (5.04 [2.67]) than the soft drink (1.43 [0.92]) and distilled water (3.41 [7.93]) solutions (P < 0.05; Kruskal-Wallis test). The color changes associated with the 3 methods were statistically equal in terms of the NBS index ranges, most frequently falling in the range of very minor to acceptable change. The powder-and-liquid method seems to be most suitable for fabricating temporary prostheses for long-term use.

Evaluation of Stain Removal Efficacy and Color Stability of Three Different Dentifrices on Artificially Stained Enamel Surface-An In Vitro Study.

AIM: The aim of the present study was to assess the stain removal ability and color stability of three distinct dentifrices on artificially stained enamel surface. MATERIALS AND METHODS: This study included 75 intact, healthy premolars free of dental caries that were extracted during orthodontic therapy. The samples were allowed to dry for 6 hours after being submerged in the prepared tea solution for roughly 18 hours every day. Then this procedure was repeated for seven successive days. All samples were randomly divided into three experimental groups with 25 samples in each group. Group I: control dentifrice, group II: dentifrice containing hydrogen peroxide, group III: dentifrice containing papain and bromelain. A specially designed toothbrushing simulator was used to brush every sample in the relevant group. Using a spectrophotometer and a measurement program, color measurement was evaluated after staining process after 4 weeks and 8 weeks of teeth cleaning. Using a profilometer, the surface roughness values (Ra) were assessed. RESULTS: After 8 weeks of brushing of stained samples, the color stability was better in dentifrice containing hydrogen peroxide (1.14 ± 0.11) followed by dentifrice containing papain and bromelain (1.22 ± 0.08) and control group (1.30 ± 0.09). And after 8 weeks of brushing of stained samples, the surface roughness was more in dentifrice containing hydrogen peroxide (0.237 ± 0.02) followed by dentifrice containing papain and bromelain (0.229 ± 0.13) and control group (0.207 ± 0.05). CONCLUSION: The present study concluded that the dentifrice containing hydrogen peroxide showed a superior whitening effect on the stained enamel surface than dentifrice containing papain and bromelain and control dentifrice. CLINICAL SIGNIFICANCE: The development of various dentifrice products has been greatly aided by the increased demand for an improved esthetic appearance. Teeth's natural color and any external stains that could accumulate on the tooth surface combine to determine a tooth's color. Additionally, the use of whitening dental pastes to remove external stains has grown in favor. With the development of these whitening toothpastes, dentifrices' ability to lessen or eliminate extrinsic dental stains has increased. How to cite this article: Mishra D, Kamath DG, Alagla M, et al. Evaluation of Stain Removal Efficacy and Color Stability of Three Different Dentifrices on Artificially Stained Enamel Surface-An In Vitro Study. J Contemp Dent Pract 2024;25(1):68-71.

Color Stability of Bioactive Restorative Material vs Nanohybrid Resin Composite: An In Vitro Study.

AIM: This study aimed to assess the color stability of bioactive restorative materials vs nanohybrid resin composites after 3 months of immersion in three frequently consumed beverages. MATERIALS AND METHODS: Thirty disk-shaped specimens of Giomer dental restorative material (Shofu, Japan) and nanohybrid resin composite (Tokuyama, Japan) were performed using a Teflon mold. Super-Snap system (Shofu, Japan) was utilized to finish and polish the specimens to be preserved for 24 hours in distilled water at 37°C. The samples had been divided into three subgroups (Coffee, tea, Pepsi) (n = 5). The initially displayed color measurements of the samples were performed using a spectrophotometer (VITA Easyshade® V). After 7 days, 30 days, and 90 days, color measurements were repeated, and the E of each sample was estimated. E of each sample was calculated. RESULTS: The Giomer group showed statistically significant higher E values than the nanohybrid resin composite where the p-value was ≤0.0001. Tea subgroup showed the highest statistically significant E values in both groups where the p-value was ≤ 0.0001. The highest statistically significant color change was recorded at 3 months. CONCLUSION: The color of bioactive restorative material is less stable if compared with nanohybrid resin composite. CLINICAL SIGNIFICANCE: As tea and coffee are popular beverages, particularly in Middle Eastern nations, dentists must advise patients about the color change of resin restorations. Patients are advised to brush their teeth immediately after consuming these beverages. How to cite this article: Saber EH, Abielhassan MH, Abed YA, et al. Color Stability of Bioactive Restorative Material vs Nanohybrid Resin Composite: An In Vitro Study. J Contemp Dent Pract 2024;25(3):221-225.

Red biocolorant from endophytic Talaromyces minnesotensis: production, properties, and potential applications.

Fungal colorants are gradually entering the global color market, given their advantages of being less harmful to human health, as well as having greater stability and biotechnological potential, compared to other natural sources. The present work concerns the isolation and identification of an endophytic filamentous fungus, together with the chemical characterization and assessment of the fluorescence, toxicity, stability, and application potential of its synthesized red colorant. The endophytic fungus was isolated from Hymenaea courbaril, a tree from the Brazilian savannah, and was identified as Talaromyces minnesotensis by phenotypic and genotypic characterization. Submerged cultivation of the fungus resulted in the production of approximately 12 AU500 of a red biocolorant which according to LC-DAD-MS analysis is characterized by being a complex mixture of molecules of the azaphilone class. Regarding cytotoxicity assays, activity against human hepatoblastoma (HepG2) cells was only observed at concentrations above 5.0 g L-1, while antimicrobial effects against pathogenic bacteria and yeast occurred at concentrations above 50.0 g L-1. The biocolorant showed high stability at neutral pH values and low temperatures (10 to 20 °C) and high half-life values (t1/2), which indicates potential versatility for application in different matrices, as observed in tests using detergent, gelatin, enamel, paint, and fabrics. The results demonstrated that the biocolorant synthesized by Talaromyces minnesotensis has potential for future biotechnological applications. KEY POINTS: • An endophytic fungus, which was isolated and identified, synthesize a red colorant. • The colorant showed fluorescence property, low toxicity, and application potential. • The red biocolorant was highly stable at pH 8.0 and temperatures below 20°C.

Formation of vinylphenolic pyranoanthocyanins by selected indigenous yeasts displaying high hydroxycinnamate decarboxylase activity during mulberry wine fermentation and aging.

The color of mulberry wine is difficult to maintain since the main chromogenic substances, anthocyanins, are severely degraded during fermentation and aging. This study selected Saccharomyces cerevisiae I34 and Wickerhamomyces anomalus D6, both displaying high hydroxycinnamate decarboxylase (HCDC) activity (78.49% and 78.71%), to enhance the formation of stable vinylphenolic pyranoanthocyanins (VPAs) pigments during mulberry wine fermentation. The HCDC activity of 84 different strains from eight regions in China was primarily screened via the deep well plate micro fermentation method, after which the tolerance and brewing characteristics were evaluated via simulated mulberry juice. The two selected strains and a commercial Saccharomyces cerevisiae were then inoculated individually or sequentially into the fresh mulberry juice, while the anthocyanin precursors and VPAs were identified and quantified via UHPLC-ESI/MS. The results showed that the HCDC-active strains facilitated the synthesis of stable pigments, cyanidin-3-O-glucoside-4-vinylcatechol (VPC3G), and cyanidin-3-O-rutinoside-4-vinylcatechol (VPC3R), highlighting its potential for enhancing color stability.

The effect of phytosphingosine associated with tooth brushing on color change, surface roughness, and microhardness of dental enamel - an in vitro and in situ study.

OBJECTIVE: This study evaluated the in vitro and in situ effects of phytosphingosine (PHS) associated with tooth brushing on color stability, surface roughness, and microhardness of dental enamel. METHODS: Sixty-four specimens of bovine teeth (6 × 6 × 2 mm) were separated into 8 groups (n = 8): S + TB: PHS (spray) + tooth brushing; TB + S: tooth brushing + PHS (spray); I + TB: PHS (immersion) + tooth brushing; TB + I: tooth brushing + PHS (immersion); TB: tooth brushing; S: PHS spray; I: immersion in PHS solution, and Saliva: immersion in saliva. Tooth brushing simulation (Mavtec, Brazil) was performed (356 rpm on 3.8 cm area by the toothbrush - Soft Tek) for 1, 7, 15, and 30 days. PHS remained in contact with specimens for 15 min. The specimens were evaluated before and after tooth brushing for color alteration (Easy Shade, VITA), and surface roughness (Model SJ-201P Mitutoyo), and Knoop microhardness (HMV-2, Shimadzu Corporation). For the in situ analyses, 8 participants were recruited and received an intraoral device with 6 fragments of bovine enamel (6 × 6 × 2 mm). The properties evaluated were the same as those of the in vitro study. Participants were randomized following best results of in vitro tested protocols, for 15 days: TB, TB + S, I + TB. Data obtained by in vitro (two-way ANOVA, Tukey, p < .05) and in situ (one-way ANOVA, Tukey, p < .05) studies were analyzed. RESULTS: The in vitro study showed that greater color change was found after 30 days. The greatest differences in surface roughness occurred between the initial value and after 1 day. Regarding microhardness, the highest values occurred after 15 and 30 days, which showed similar results. The in situ study showed greater color changes for the TB and I + TB, and greater surface roughness changes for TB as well as a similar increase in microhardness for the PHS protocols, which were higher than TB. CONCLUSIONS: Phytosphingosine leads to an increase in performance regarding color stability, surface roughness, and microhardness when applied. In general, the application of PHS after brushing showed a positive impact on its performance. CLINICAL RELEVANCE: Phytosphingosine proved to be interesting for compound prevention formulations in the dentistry field.