ABSTRACT
Objective@#To evaluate the impact of ultra-high-molecular-weight polyethylene (UHMWPE)-Ribbond fibers, when combined with different restorative materials, on fracture resistance and marginal adaptation of isolated primary molar defects, to provide a reference for clinical practice.@*Methods@#This study was approved by the Ethics Review Committee. A total of 72 extracted primary molars with complete crowns were collected, and 66 primary molars were randomly assigned as experimental groups for the fracture resistance and microleakage tests. The molars were divided into six groups (n = 11) based on the type of restorative materials and the application of Ribbond fibers: Group A1, 3M Filtek Z250 + Ribbond; Group A2, 3M Filtek Z250; Group B1, Beautifil II LS + Ribbond; Group B2, Beautifil II LS; Group C1, 3M Filtek Bulk Fill + Ribbond; and Group C2, 3M Filtek Bulk Fill. Groups A1, B1 and C1 received the fiber-reinforcing technique, whereas Groups A2, B2 and C2 received the direct restorative technique; the remainings were in Group D (blank control group), which did not receive treatment for the fracture resistance test. The fracture resistance test was divided into six experimental groups and one blank control group (n = 6). Primary molar teeth in each experimental group were prepared with Class II cavities and filled. The fracture load of all samples was detected, and the fracture mode was analyzed after thermal cycling. The microleakage test was divided into six experimental groups, with five in each group. Class I cavities with a diameter of 3 mm and depth of 2.5 mm were prepared within the mesial and distal marginal ridges on the occlusal surface and filled for primary molars in each group. Marginal microleakage was assessed after thermal cycling.@*Results@#The fracture resistance test results showed that the fracture resistance in groups that received the fiber-reinforcing technique was greater than that in groups that received the direct restorative technique: Group A1>Group A2, Group B1>Group B2, Group C1>Group C2 (P<0.05). The application of Ribbond fibers increased fracture resistance to all tested restorative materials by 37.08% to 39.34%. The proportion of tooth frac-ture decreased significantly in groups A1, C1 compared with A2, C2, with a significant increase in the occurrence rate of “Repairable” (P<0.05). The fracture resistance in Group A1 was significantly greater than that in Group B1 and Group C1 (P<0.05). The marginal microleakage test results showed that the microleakage depth in groups that received the fiber-reinforcing technique was smaller than that in groups that received the direct restorative technique: Group A1<Group A2, Group B1<Group B2, Group C1<Group C2 (P<0.05). The microleakage depth in groups that received the fiber-reinforcing technique decreased by 53.90% to 66.96% compared to that in groups that received the direct restorative technique. The microleakage depth in Group B1 was significantly less than that in Group A1 and Group C1.@*Conclusion@#The application of Ribbond fibers combined with various restorative materials could enhance fracture resistance and diminish the microleakage depth to improve marginal adaptation.
ABSTRACT
Objective @#To explore the effects of two hemostatic agents on the bonding strength of different bonding systems in primary tooth dentin.@*Methods @# Seventy-two retained deciduous teeth were randomly selected. Forty-eight teeth were used to construct the microleakage model, the other 24 teeth were cut along the mesial and distal directions and 48 samples were obtained to construct the shear bond strength model. The two experiments were divided into 2 groups. Group A was the total-etch group: A1 (ViscoStat + Spectrum Bond NT); A2 (ViscoStat Clear + Spectrum Bond NT); and A3 (Non + Spectrum Bond NT); Group B was the self-etch group: B1 (ViscoStat + Single bond Universal Adhesive); B2 (ViscoStat Clear + Single bond Universal Adhesive); and B3 (Non + Single bond Universal Adhesive). Microleakage experiments and shear bond strength experiments were carried out respectively and the morphology of the fracture surface was observed by scanning electron microscopy.@* Results @#There was no significant difference in microleakage among groups A1, A2, and A3 (P > 0.05). There was no significant difference in microleakage among groups B1, B2, and B3 (P > 0.05). There was no significant difference in the shear bond strength among groups A1, A2 and A3 (P > 0.05). The shear bond strength of groups B1 and B2 was significantly lower than that of group B3 (P < 0.05). There was no significant difference between groups B1 and B2 (P > 0.05). @*Conclusion@#ViscoStat and ViscoStat Clear had no effect on the marginal integrity of deciduous tooth dentin under the different bonding systems. The two hemostatic agents reduced the shear bonding strength of deciduous tooth dentin under the self-etch adhesive system, but had no effect on the shear bonding strength of deciduous tooth dentin under the total-etch adhesive system.