ABSTRACT
Objective:To explore the application value of electromagnetic navigation technique in the removal of hematoma under neuroendoscope.Methods:Forty-three patients with supratentorial spontaneous cerebral hemorrhage, accepted removal of hematoma under neuroendoscope in our hospital from October 2015 to February 2019, were chosen in our study; 22 patients (navigation group) were performed the removal under the guide of real-time electromagnetic navigation, and 21 (non-navigation group) were performed the removal under neuroendoscope only. The amount of cerebral hemorrhage, operation time, residual amount of hematoma and hematoma clearance rate were compared between the two groups. Fugl-Meyer Assessment (FMA) was used to evaluate the motor function of the affected limbs two weeks after surgery. The anisotropy fraction (FA) values of fibers of affected pyramidal tracts and contralateral pyramidal tracts were examined by diffusion tensor imaging (DTI), and the relative FA (rFA) value (FA values of affected side/contralateral side) was calculated. Barthel index was used to evaluate the basic daily activities of the patients 6 months after surgery.Results:There was no significant difference between the navigation group and the non-navigation group in the amount of cerebral hemorrhage before surgery, amount of residual hematoma after surgery, hematoma clearance rate, and operation time ( P>0.05). FMA scores of upper and lower limbs, FA and rFA values of the affected side in the navigation group were significantly higher than those in the non-navigation group two weeks after surgery ( P<0.05). Barthel index of patients in the navigation group was statistically higher than that of the non-navigation group 6 months after surgery ( P<0.05). Conclusion:Electromagnetic navigation technique can guide endoscopy to effectively clear the supratentorial hypertensive cerebral hemorrhage without obviously increasing the operation time; effective protection of pyramidal fibers can improve the prognoses of patients.
ABSTRACT
BACKGROUND:Currently, there are many studies on colapsed repair, but a systematic and horizontal comparison is not reported yet. OBJECTIVE: To compare the effect of conventional resin adhesive, resin adhesive+silane coupling agent and adjacent surface open part of the crown on colapsed repair through clinical trial and in vitro experiment. METHODS: (1) Clinical trial: 90 patients with porcelain colapse were randomized into three groups, and respectively treated with conventional resin adhesive, resin adhesive+silane coupling agent and adjacent surface open part of the crown. Success rate was measured and compared among three groups at 1 year after repair. (2) In vitro test: Twenty test specimens were equaly divided into two groups, and treated with conventional resin adhesive and resin adhesive+silane coupling agent, respectively. Then, shear strength was detected in the two groups. Twenty double-crown specimens were equaly divided into four groups. The first three groups were treated with sand blasting, silane coupling agent and their combination treatment, respectively; the rest group had no treatment (control group). After repair, the tensile strength of each specimen was detected.RESULTS AND CONCLUSION:The success rate of colapsed repair was 37% for conventional resin adhesive, 90% for resin adhesive+silane coupling agent and 100% for adjacent surface open part of the crown. The shear strength was (13.978±0.343) MPa for the conventional resin adhesive and (10.058±0.64) MPa for resin adhesive+silane coupling agent, and there was a significant difference between two methods (P < 0.01). The tensile strength was (0.68±0.04) kN in the control group, (1.00±0.02) kN in the sand blasting group, (1.31±0.08) kN in silane coupling agent group, and (1.09±0.04) kN in the combination group, and there was a significant differences between groups (P < 0.01). Experimental results show that the silane coupling agent+resin adhesive treatment and adjacent surface open part of the crown are superior to conventional resin adhesive.
ABSTRACT
BACKGROUND:Porcelain jacket crowns have achieved good results in the repair of porcelain ceramic crown and bridge colapse. OBJECTIVE:To test the bond strength of single porcelain jacket crown, thus determining the feasibility of clinical application of repairing colapsed crown and fixed bridge by porcelain jacket crown, and meanwhile to discuss the influence between blastsanding and silane coupling agent treatment on the metal bonding strength in the repair of porcelain fracture. METHODS: The porcelain jacket crown was cast in the same shape from disk-shaped waxpatterns. Twenty specimens were chosen without blowholes and casting defects and they were al routinely burnished and cleaned in an ultrasonic bath and dried using an oil-free air stream stand-by. Then we randomly divided the specimens into four groups: specimens were treated with nothing (control), sandblast, silane coupling agent and sandblast+silane coupling agent, respectively. Each of the specimen was bonded with Poly-F Plus. AG-10TA universal testing machine was used to test the tensile strength. RESULTS AND CONCLUSION:The tensile bond strength of control, sandblast, silane coupling agent and sandblast+silane coupling agent groups respectively were (0.68 0.04), (1.00 0.02), (1.31 0.08), and (1.09 0.04) kN. There were significant differences between groups (P < 0.01). In the control group, the metal surface was smooth, showing some irregular smal superficial veins. In the sandblast group, the metal surface showed irregular scaly protrusions conducive penetrate adhesives. In the silane coupling group, the metal surface manifested a honeycomb structure in favor of chimeric adhesives. The sandblast+silane coupling agent group showed some metal projections ranging in size, on the rough metal surface, which was conducive to bond. Porcelain jacket crown applied to repair colapsed crown and fixed bridge is feasible. Sandblasting and silane coupling agent can improve bond strength of porcelain jacket crown. The bond strength of metal specimens treated with silane coupling agent is the best folowed by the sandblasting+silane coupling agent.