Topographic analysis of fiber posts after surface disinfection with different methods

Aims: This study aims to comprehensively examine the surface morphology of fiber posts after undergoing various disinfection methods, utilizing scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). Materials and Methods: Twenty-one fiber posts were randomly allocated into seven experimental groups, each consisting of three samples. The disinfection methods employed were as follows: GC - no disinfection treatment; GAL - immersion in 70% alcohol, following the manufacturer's recommended protocol; GHP - soaking in 2.5% sodium hypochlorite for a duration of 10 minutes; GCL - soaking in 2% chlorhexidine gluconate for a period of five minutes; GAC - 30-second etching with 35% phosphoric acid; GPH - soaking in 10% hydrogen peroxide for a duration of 20 minutes; and GSL - autoclave sterilization. Following the disinfection procedures, SEM was employed to scrutinize the surface topography of the posts, while EDX was utilized to identify the chemical elements present on the sample surfaces. Subsequently, a descriptive analysis was conducted on the SEM images and EDX data. Results: SEM analysis revealed that all groups exhibited regions with epoxy resin-coated fibers alongside sections with exposed glass fibers. Analysis of the EDX data indicated that there were no significant differences in the predominant chemical elements across the groups. Carbon (C) and oxygen (O) registered the highest peaks, followed by silicon (Si), zirconium (Zr), sodium (Na), aluminum (Al), and calcium (Ca). Conclusions: The disinfection methods under investigation did not induce substantial alterations in the surface morphology of the fiber posts.

Bisphenol A released and ultrastructural changes in dental composite resins

Dental composite resins may release bisphenol-A or similar molecules affecting patient health and the environment. This study measured bisphenol-A release from three commonly used in patients composite resins (Filtek™ Z350 XT, Filtek™ P60, Filtek™ Bulk Fill) immersed in three liquid mediums (artificial saliva, 0.001 M lactic acid and 15% ethanol) and assessed the changes in the surface micromorphology.The released BPA was measured by HPLC at basal time (t=0), 1 h, 1 d, 7 d and 30 d. Topographic analysis of specimens was performed by scanning electron microscopy (SEM). The data were analyzed using one-way ANOVA and Tukey post-hoc test (P < 0.05). BPA in solution increased significantly in the three DCRs immersed in 0.001 M lactic acid at all times. SEM micrographs of the specimen in 0.001 M lactic acid disclosed more structural defects than others. The surface of the three composite resins was morphologically affected by their immersion in all solutions. SEM evidenced that the dental materials underwent erosion and cracks with filler particles protruding from the surface. The morphological changes in tested dental materials produced by exposure to these solutions are potentially dangerous to patients by causing caries, infections, and partial loss of dental material.

Alpaca (Vicugna pacos) Skin Analyzed Under Architecture and Structure / Piel de Alpaca (Vicugna pacos) Analizada Bajo Arquitectura y Estructura

SUMMARY: This study evaluated the morphology of alpacas skin. Biopsies were collected and samples were fixed in 10 % neutral buffered formalin for histological procedures. The sections were stained with hematoxylin and eosin, picrosirius red and Masson's trichrome. Types I, III and IV collagen were analyzed by immunohistochemistry. The derma presented sebaceous and sweat glands, as well as follicular groups with medullated fibers. Type I and type IV collagen were observed at epidermis and dermis as well as in glandular structures and hair follicles. The collagen III, was observed only in dermis.

Este estudio evaluó la morfología de la piel de alpacas. Se recogieron biopsias y las muestras se fijaron en formalina tamponada neutra al 10 % para procedimientos histológicos. Las secciones se tiñeron con hematoxilina y eosina, rojo picrosirius y tricrómico de Masson. El colágeno tipo I, III y IV se analizó mediante inmunohistoquímica. La dermis presentó glándulas sebáceas y sudoríparas, así como grupos foliculares con fibras medulares. Se observó colágeno tipo I y tipo IV en la epidermis y la dermis, así como en estructuras glandulares y folículos pilosos. El colágeno III, se observó únicamente en la dermis.

Exploring Scientific Connotation of "Fried Charcoal Survivability" of Lonicerae Japonicae Flos Based on Color-composition Correlation / 中国实验方剂学杂志

ObjectiveTo explore the scientific connotation of fried charcoal survivability of Lonicerae Japonicae Flos（LJF） by analyzing the correlation between the color change and the intrinsic components during the processing of LJF Carbonisata（LJFC）， and taking pH， charcoal adsorption and microscopic characteristics as indexes. MethodLJFC samples with different degrees of processing were prepared according to the stir-frying time of 0.0， 1.5， 3.0， 4.5， 6.0， 7.5， 9.0， 10.5 min（numbered S1-S8）， and the contents of gallic acid， chlorogenic acid， cryptochlorogenic acid， rutin， luteoloside， isochlorogenic acid A and isochlorogenic acid C were determined by high performance liquid chromatography（HPLC）， and the L*（brightness）， a*（red-greenness） and b*（yellow-blueness） of LJFC samples with different degrees of processing were determined by spectrophotometer， and the correlation analysis and principal component analysis（PCA） between the contents of seven representative components and the color of the samples were carried out by SPSS 26. 0 and SIMCA-P 14.1. Then pH， adsorption force and characteristic structure of different samples of LJFC were detected and the processing pattern of LJFC was analyzed. ResultThe results of quantitative analysis revealed that the contents of luteoloside， rutin， chlorogenic acid and isochlorogenic acid A gradually decreased， and the contents of cryptochlorogenic acid， isochlorogenic acid C and gallic acid firstly increased and then decreased. The L* and b* of the sample powders decreased， and a* showed a trend of increasing and then decreasing. The L* and b* were positively correlated with the contents of chlorogenic acid， rutin， luteoloside， isochlorogenic acid A， b* was positively correlated with the content of gallic acid， and a* was positively correlated with the contents of cryptochlorogenic acid and isochlorogenic acid C. PCA revealed that samples could be clearly divided into 3 groups， S1-S2 as one group， S3-S5 as one group， and S6-S8 as one group， with S3 having the highest score. The results of regression analysis showed that only isochlorogenic acid C could be used to predict the contents of components by colorimetric values combined with regression equations. Physicochemical analysis showed that pH of LJFC increased with the increase of degree of charcoal stir-frying， while adsorption force showed a tendency of increasing and then decreasing， with the highest adsorption force in the S5 sample， and the non-glandular hairs， calcium oxalate clusters and pollen grains had a varying degree of decreasing with the deepening of processing degree， and the microstructures of S6-S8 samples were obviously charred with pollen grains almost invisible. ConclusionThe changes in chemical composition and color characteristics of LJFC during the processing have certain correlations， combined with the changes in physicochemical properties， S5 sample is found to be the optimal processed products， which can provide a reference for the processing standardization and quality evaluation of LJFC， and enrich the scientific connotation of fried charcoal survivability of LJF.

In Situ Labeling of Erythrocyte Membrane Anion Channel Proteins with Gold Nanoparticles Observed by Cryo-Scanning Electron Microscopy / 分析化学

Band 3 protein is an important channel protein in the erythrocyte membrane which mediates the anion transport process inside and outside the cell membrane,as well as contributes to the maintenance of erythrocyte morphology,and has important physiological functions.However,the distribution state of this protein in the primary cell membrane is not known.Cryo-scanning electron microscopy enables imaging of the surface morphology of biological samples in a near-physiological state.In order to investigate the distribution of band 3 protein on erythrocyte membranes under physiological conditions,the present study utilized 5-nm gold nanoparticles modified with the antibodies to specifically bind to the band 3 protein on human blood erythrocyte membranes and imaged them by cryo-scanning electron microscopy,to obtain distribution of band 3 protein on human blood erythrocyte membranes.The results showed that the membrane proteins on the erythrocyte membranes tended to be clustered and distributed to form ″protein islands″,and band 3 proteins were mainly distributed in these protein islands,which were tightly connected with each other to form several functional microregions to play their respective roles.

A microscopia eletrônica de varredura pode ser usada para medir quantitativamente a rugosidade da dentina? / Can Scanning Electron Microscopy be used to quantitatively measure dentine roughness?

Objective: The aim of this study was to determine if SEM used with imaging software could be used to quantitatively determine the extent of dentine roughness due to tooth-brushing. Material and methods: Flat, polished dentine surfaces were subjected to 25,000 cycles of simulated tooth-brushing at 2 strokes per second with a load of 200 g. At the end of the brushing cycle, dentine surfaces were first assessed using profilometry and then subjected to SEM analysis. Ra (average roughness) readings were obtained for profilometric assessment. Using imaging software, the horizontal distance between adjacent characteristic grooves noted on micrographs was measured, ensuring that the middle of each crest of the associated groove was used as the reference point, the Crest-to-Crest distance (C-C distance). These two parameters were examined statistically for correlation. Results: When Spearman Rank tests were utilized the correlation between average Ra and crest to crest measurements was 0.709 (p <0.01). The Bland Altman plot, however, showed poor agreement between the two test parameters. Conclusion: Further work is needed to validate the use of this methodology in the quantitative assessment of tooth surface loss due to abrasion (AU)

Objetivo: O objetivo deste estudo foi determinar se o MEV usado com software de imagem poderia ser usado para determinar quantitativamente a extensão da rugosidade da dentina devido à escovação dentária. Material e Métodos: Superfícies dentinárias planas e polidas foram submetidas a 25.000 ciclos de escovação dentária simulada a 2 movimentos por segundo com uma carga de 200g. No final do ciclo de escovação, as superfícies dentinárias foram primeiro avaliadas por perfilometria e depois submetidas à análise MEV. Leituras de Ra (rugosidade média) foram obtidas para avaliação perfilométrica. Utilizando um software de imagem, foi medida a distância horizontal entre sulcos característicos adjacentes observados nas micrografias, garantindo que o meio de cada crista do sulco associado fosse usado como ponto de referência, a distância crista a crista (distância CC). Esses dois parâmetros foram examinados estatisticamente para correlação. Resultados: Quando foram utilizados os testes de Spearman Rank, a correlação entre a média de Ra e as medidas de crista a crista foi de 0,709 (p<0,01). O gráfico de Bland Altman, no entanto, mostrou fraca concordância entre os dois parâmetros de teste. Conclusão: Mais trabalhos são necessários para validar o uso desta metodologia na avaliação quantitativa da perda da superfície dentária devido à abrasão(AU)

First report of white piedra caused by Cutaneotrichosporon debeurmannianum

ABSTRACT Piedras are small nodules found on the hair shafts. White piedra was initially described as caused by Trichosporon beigelii, which was later reclassified in several species. We describe the first case of white piedra caused by Cutaneotrichosporon debeurmannianum. Affected hairs were examined in natura with scanning electron microscopy, after gold metallization. The typical whitish cerebriform creamy colony was obtained in Sabouraud medium. Fungal genomic DNA extracted from cultures and locus was amplified with the NL1/NL4 primer pair from the D1/D2 region of the large ribosomal subunit (LSU) of 28S rRNA. With scanning electron microscopy, nodules are easily identified surrounding the hair shaft; with high magnifications, rounded structures adhered to each other were identified. Comparison of the nucleotide sequences of IMT-1703 Cutaneotrichosporon debeurmannianum revealed 99.6% similarity with the 28S large ribosomal unit rDNA sequence. This case of white piedra was caused by Cutaneotrichosporon debeurmannianum.

Synthesis, characterization and protection effect of black rice anthocyanins nano-composite against hepatotoxicity induced by methotrexate in rats

Abstract The present study aimed to investigate the beneficial of prepared black rice anthocyanins nano-composite (An-AgNps) against hepatotoxicity induced by methotrexate (MTX) in rats. Anthocyanins nano-composite was prepared by silver as the metallic ion reduction and were characterized by IR and SEM. The rats in our experiment were divided into five groups. Serum lipid profile, serum transaminases (ALT and AST), ALP, LDH, TBA, GSH and SOD were examined. The results show that SEM of An-AgNps has average particle size from 70 to 130nm. In the group treated with MTX; TC, TG, LDL-c, ALT, AST, ALP, LDH and TBA levels were significantly (P0.05) increased than NC, while, HDL-c, SOD and GSH levels were significantly (P0.05) decreased. On the other hand, An-AgNps + MTX treated groups were reversed the levels of all biomarkers similar to NC. In conclusion, the results show that An-AgNps has a protective effect on MTX-induced hepatotoxicity and oxidative stress.

Resumo O presente estudo teve como objetivo investigar o benefício de nanocompósito de antocianinas de arroz preto preparado (An-AgNps) contra a hepatotoxicidade induzida por metotrexato (MTX) em ratos. O nanocompósito de antocianinas foi preparado a partir da prata por meio da redução do íon metálico e caracterizado por IR e SEM. Os ratos em nosso experimento foram divididos em cinco grupos, e foram examinados o perfil lipídico sérico, as transaminases séricas (ALT e AST), ALP, LDH, TBA, GSH e SOD. Os resultados mostram que SEM de An-AgNps tem tamanho médio de partícula de 70 a 130 nm. No grupo tratado com MTX, os níveis de TC, TG, LDL-c, ALT, AST, ALP, LDH e TBA aumentaram significativamente (P 0,05) do que NC, enquanto os níveis de HDL-c, SOD e GSH diminuíram significativamente (P 0,05). Por outro lado, nos grupos tratados com An-AgNps + MTX, foram revertidos os níveis de todos os biomarcadores semelhantes ao NC. Em conclusão, os resultados mostram que o An-AgNps tem um efeito protetor contra a hepatotoxicidade induzida pelo MTX e o estresse oxidativo.

Avaliação dos Efeitos da Remoção da Resina Residual e do Polimento na Superfície do Esmalte após Descolagem do Braquete / Evaluation of the Effects of Residual Resin Removal and Polishing on the Enamel Surface after Bracket Debonding

Considerando o uso de brocas para remoção da resina residual após descolagem do braquete e a possibilidade de injúrias à superfície do esmalte após o uso dessas brocas, este trabalho teve como objetivo realizar um estudo experimental, para avaliar a variação do aspecto superficial do esmalte de forma qualitativa, por meio da avaliação com imagens topográficas do esmalte dentário, utilizando-se a Microscopia Eletrônica de Varredura (MEV), a qual permitiu ilustrar e avaliar a superfície do esmalte após a fase de polimento final, realizada por dois métodos: taça de borracha ou escova Robinson. Foram utilizados 25 dentes pré-molares humanos, obtidos a partir de exodontias em pacientes que procuraram voluntariamente o curso de Residência em Cirurgia da Clínica Odontológica Universitária da Universidade Estadual de Londrina. Os dentes foram divididos em quatro grupos: A, B, C e D, contendo 6 dentes cada, de acordo com as brocas utilizadas para a remoção do remanescente adesivo e o polimento escolhido, além de um dente como "controle". Foi avaliada a rugosidade superficial do esmalte após a remoção da resina e a superfície do esmalte após o polimento com as duas opções apresentadas. Os resultados mostraram que, por observação e inspeção, as brocas removeram a resina residual de todos os dentes, porém, causaram riscos e ranhuras, como evidenciado nas imagens em MEV. Concluiu-se que não houve diferença estatística entre os métodos de polimento e que ambos foram importantes para a redução das marcas abrasivas, proporcionando uma superfície mais lisa do esmalte.

Considering the use of specific burs to remove residual resin after bracket debonding and the possibility of injuries to the dental enamel after using these burs, this study aimed to verify the variation in the enamel surface appearance in a qualitative way and evaluation with topographic images of the dental enamel. The use of Scanning Electron Microscopy (SEM) allowed to illustrate and evaluate the enamel surface after the final polishing phase using two methods: rubber cup or Robinson brush. Twenty-five human premolar teeth were obtained from extractions in patients who voluntarily sought the Oral Maxillofacial Surgery Residency at the Dental School from the State University of Londrina; the teeth were divided into four groups A, B, C and D containing 6 teeth each according to the burs used to remove the remaining adhesive and the chosen polishing, in addition to one tooth as a "control". Dental enamel surface roughness was evaluated after resin removal and enamel surface after polishing with the two methods presented. The results showed that by observation and inspection, the burs removed residual resin from all teeth, however, caused scratches and grooves as evidenced in the SEM images. Based on the results, there was no statistical difference between the polishing methods, and both were important for the reduction of abrasive marks and provided a smoother enamel surface.

Removal and identification of a subconjunctival parasite by light and scanning electron microscopy

Background: Ophthalmic dirofilariasis is an uncommon zoonotic parasitic infection caused by species of Dirofilaria, a dog tapeworm that is transmitted to human by mosquitoes. Man is a dead?end host for the parasite. Ophthalmic involvement is rare and includes periorbital, subconjunctival, subtenon, and intra?ocular involvement. We report the removal of a subconjunctival worm and identification by light microscopy (LM) and scanning electron microscopy (SEM). Purpose: A 62?year?old female presented with complaints of redness, discharge, and foreign body sensation with difficulty in opening eyes in the left eye for the last 3 days. The patient is a non?vegetarian. On examination, her best corrected visual acuity in both eyes was 20/20. On slit lamp examination, there was a long, thin, round, coiled white subconjunctival live worm in the left eye superiorly. The rest of anterior segment evaluation, intra?ocular pressure, and fundus was normal in both eyes. The parasite was removed under local anesthesia from subconjunctival space [Video]. External surface morphology under LM revealed fine transverse cuticular striations with tapered cephalic and caudal ends. Uterus was long and coiled with indistinguishable masses inside. The finding was also confirmed by SEM. Synopsis: A subconjuctival parasite was removed and identified as Dirofilaria repens by characteristic LM and SEM findings. Highlight: Dirofilaria species may lodge in many tissues of human bodies including eye and adnexa. Dirofilaria is a natural parasite of carnivorous animals, mostly dogs, cats, and foxes.[1] The most common mode of transmission to human is usually by bite of mosquitoes like Culex and Aedes, which are considered as vectors, and it is often thought that parasitemia is because of accidental conduction.[1] Simple surgical removal of the worm is curative. After removal, the worm should be visualized directly under LM. All the internal structures of the transparent worm could be seen and compared with those under SEM.

Light Microscopic, Ultrastructure Analysis and Functional Morphology of Cornu aspersum Spermatozoa Contained in the Frozen Hermaphroditic Duct / Análisis de Microscopía de Luz, Ultraestructura y Morfología Funcional de Espermatozoides de Cornu aspersum Contenidos en el Conducto Hermafrodita Congelado

SUMMARY: In this study we describe the functional morphology of Cornu aspersum (Helix aspersa), spermatozoa using light, scanning (SEM) and transmission electron (TEM) microscopies. The studies were performed with sperm located in the frozen hermaphroditic duct. Our results showed that the head presents an elongated conical shape slightly coiled in a corkscrew, with the nucleus partially covered by an acrosome, where an apical vesicle is located at the lateralized apex. This peculiar shape suggests the helical displacement movement of the spermatozoa. The head and the nucleus are slightly larger size compared to those of other gastropod species. The intermediate tract is surrounded by a mitochondrial complex and a glycogen helix. The glycogen helix is coiled helically along the intermediate tract, presenting at least five twists of glycogen helices. The complexity of both the mitochondrial complex and the glycogen helix suggests a high metabolic consumption considering the long period of time until fertilization occurs. Our findings on the detailed characterization of Cornu aspersum spermatozoa, obtained from a frozen hermaphroditic duct can contribute to a better understanding of the functional morphology of sperm and serve as a reference for future studies.

En este estudio describimos la morfología funcional de Cornu aspersum (Helix aspersa), espermatozoides utilizando microscopías de luz, barrido (SEM) y electrónica de transmisión (TEM). Los estudios se realizaron con espermatozoides localizados en el conducto hermafrodita congelado. Nuestros resultados mostraron que la cabeza presenta una forma cónica alargada ligeramente enrollada en un tirabuzón, con el núcleo parcialmente cubierto por un acrosoma, donde se ubica una vesícula apical en el ápice lateralizado. Esta peculiar forma sugiere el movimiento de desplazamiento helicoidal de los espermatozoides. La cabeza y el núcleo son de un tamaño ligeramente mayor en comparación con los de otras especies de gasterópodos. El tracto intermedio está rodeado por un complejo mitocondrial y una hélice de glucógeno. La hélice de glucógeno se enrolla helicoidalmente a lo largo del tracto intermedio, presentando al menos cinco giros de hélices de glucógeno. La complejidad tanto del complejo mitocondrial como de la hélice de glucógeno sugiere un alto consumo metabólico considerando el largo período de tiempo hasta que ocurre la fecundación. Nuestros hallazgos sobre la caracterización detallada de los espermatozoides de Cornu aspersum, obtenidos de un conducto hermafrodita congelado, pueden contribuir a una mejor comprensión de la morfología funcional de los espermatozoides y servir como referencia para futuros estudios.

Depth of cure, mechanical properties and morphology of dual-cure bulk-Fill composites / Profundidad de curado, propiedades mecánicas y morfología de resinas compuestas duales

This study evaluated selected structural and physical properties, such as degree of conversion (DC), Vickers hardness (VHN), and compression strength (CS), of three new dual-cure bulk-fill resin-based composites (RBCs; ACTIVA, HyperFIL, and Fill-Up) and compared them to those of a conventional RBC (Filtek Z250) at three clinically relevant depths. Samples (n=180) were prepared in three depths (2,4, and 6mm). Fourier-transform infrared spectroscopy (FTIR) analysis and VHN and CS tests were performed. The DC value was calculated by considering the relative change in the aliphatic C=C peaks. The fractured surfaces of representative samples were characterized using scanning electron microscopy (SEM). Data were statistically evaluated using two-way analysis of variance and post hoc Bonferroni tests (p<0.05). According to the VHN results, Filtek Z250 showed the highest bottom/top hardness ratio (97.94±1.01) at 2mm thickness and ACTIVA showed the lowest bottom/top hardness ratio (43.48±5.64) at 6mm thickness (p<0.001). According to the FTIR results, the DC decreased with increasing thickness in all materials (p<0.05). Filtek Z250 showed the highest (301±12.4 MPa) and ACTIVA exhibited the lowest (232±17.2 MPa) CS values at 2mm thickness (p<0.05). The lowest CS values were obtained for ACTIVA, and the highest values were obtained for Filtek Z250 for samples with thicknesses of 4 and 6mm, respectively (p<0.05). The structural features of restorative composites, such as the resin chemistry and filler type and content, and the operational parameters (i.e., material thickness and curing conditions) strongly affect crosslinking reactions and thus the DC, VHN, and CS values.

Este estudio evaluó propiedades físicas y estructurales, como el grado de conversión (DC), la dureza Vickers (VHN) y la resistencia a la compresión (CS), de tres nuevos compósitos a base de resina de curado dual tipo bulk (RBC; ACTIVA , HyperFIL y Fill-Up) y los comparó con los de una resina compuesta convencional (Filtek Z250) en tres profundidades clínicamente relevantes. Se prepararon muestras (n=180) en tres profundidades (2,4 y 6mm). Se realizaron análisis de espectroscopia infrarroja por transformada de Fourier (FTIR) y pruebas VHN y CS. El valor de DC se calculó considerando el cambio relativo en los picos alifáticos C=C. Las superficies fracturadas de muestras representativas se caracterizaron mediante microscopía electrónica de barrido (MEB). Los datos se evaluaron estadísticamente mediante análisis de varianza de dos vías y pruebas post hoc de Bonferroni (p<0,05). De acuerdo con los resultados de VHN, Filtek Z250 mostró la relación de dureza inferior/superior más alta (97,94±1,01) con un espesor de 2mm y ACTIVA mostró la relación de dureza inferior/superior más baja (43,48±5,64) con un espesor de 6mm (p<0,001). De acuerdo con los resultados de FTIR, la DC disminuyó al aumentar el espesor en todos los materiales (p<0,05). Filtek Z250 mostró los valores de CS más altos (301±12,4 MPa) y ACTIVA los más bajos (232±17,2 MPa) a 2mm de espesor (p<0,05). Los valores más bajos de CS se obtuvieron para ACTIVA y los valores más altos para Filtek Z250 para muestras con espesores de 4 y 6mm, respectivamente (p<0,05). Las características estructurales de las resinas compuestas de restauración, como la química; además del tipo y contenido del relleno, y los parámetros operativos (es decir, el espesor del material y las condiciones de curado) afectan en gran medida las reacciones de interacción química y, por lo tanto, los valores de DC, VHN y CS.

Evaluation of Structural and Compositional Changes on the Root Surface Exposed to Diode Laser (810 nm): An In?vitro Study

Background: The laser therapy has been used as an adjuvant for conventional periodontal disease as they exhibit a bactericidal effect on scaling and root planning by its thermal and photo disruptive effects on the pathogens. This study focuses on the structural and compositional changes induced on the root surfaces of teeth following diode laser (DL) application with increasing quantum of exposure time. Objective: The objective of this study was to evaluate the structural and compositional changes on the root surface of extracted human permanent teeth after application of DLs (810 nm) with varying time interval. Materials and Methods: Twenty samples of single?rooted periodontally compromised extracted teeth were utilized for this study. Root planning was done and the roughness caused by the instrumentation was measured using profilometric analysis. Then, the samples were divided into four groups, with DL application time: Group 1 – laser application for 15 s, Group 2 – laser application for 30 s, Group 3 – laser application for 45 s, and Group 4 – laser application for 60 s. A scanning electron microscope was used to examine the cemental surface and energy?dispersive X?ray analysis software assesses the compositional changes of the teeth in each group. Results: This study reveals that on exposure of DL (810 nm) on the root surface when time of exposure increases, there were relative increases in surface irregularities and charring. There were significant changes in the chemical composition of the tooth surface.

Impact of radiotherapy on the morphological and compositional structure of intra-radicular dentin

Abstract Considering the side effects in the oral cavity and dental structures of radiotherapy (RDT) for head and neck cancer, this study aimed to evaluate the effects of RDT on the root dentin concerning the obliteration of dentinal tubules, the inorganic composition of intra-radicular dentin, and the integrity of collagen fibers. Thirty human canines were selected from a biobank and randomly divided into two groups (n=15). The samples were sectioned buccolingually, and a hemisection was used for structural analysis by scanning electron microscopy (SEM) and energy-dispersive X-ray spectrometer (EDS). Low-vacuum SEM images were obtained at 2000-x magnification to observe the obliteration of the dentinal tubules. Moreover, compositional evaluation was performed using EDS. After RDT, the SEM and EDS analyses were repeated using the same methodology. RDT was applied fractionally at 2 Gy per day, 5 days per week, for 7 weeks, resulting in a total dose of 70 Gy. The collagen integrity of the irradiated and non-irradiated samples was analyzed using Masson's trichrome and picrosirius red staining polarization microscopy. Samples subjected to RDT exhibited dentinal tubule obliteration (p < 0.001); low integrity of type I and III collagen fibers (p < 0.05); compositional reduction of calcium (p = 0.012), phosphorus (p = 0.001), and magnesium (p < 0.001); an increased Ca/P ratio (p < 0.001). RDT affects the structure of dentinal tubules, the inorganic composition of intra-radicular dentin, and the collagen fiber integrity in the root dentin, which may interfere with the effectiveness and durability of dental procedures.

Resumo Considerando os efeitos colaterais na cavidade oral e estruturas dentárias da radioterapia (RDT) para o câncer de cabeça e pescoço, este estudo teve como objetivo avaliar os efeitos da RDT sobre a dentina radicular quanto à obliteração dos túbulos dentinários, a composição inorgânica da dentina intra-radicular e a integridade das fibras colágenas. Trinta caninos humanos foram selecionados de um biobanco e divididos aleatoriamente em dois grupos (n=15). As amostras foram seccionadas no sentido vestíbulo-lingual, e uma hemissecção foi utilizada para análise estrutural por microscopia eletrônica de varredura (MEV) e espectrômetro de raios X de dispersão de energia (EDS). Imagens de MEV de baixo vácuo foram obtidas com aumento de 2500x para observar a obliteração dos túbulos dentinários. Além disso, a avaliação composicional foi realizada usando EDS. Após a RDT, as análises em MEV e EDS foram repetidas usando a mesma metodologia. A RDT foi aplicada fracionada a 2 Gy por dia, 5 dias por semana, durante 7 semanas, resultando em uma dose total de 70 Gy. A integridade do colágeno das amostras irradiadas e não irradiadas foi analisada usando microscopia de polarização de coloração com tricrômio de Masson e picrosirius red. As amostras submetidas a RDT apresentaram obliteração dos túbulos dentinários (p < 0,001); baixa integridade das fibras colágenas tipo I e III (p < 0,05); redução composicional de cálcio (p = 0,012), fósforo (p = 0,001) e magnésio (p < 0,001); e uma relação Ca/P aumentada (p < 0,001). A RDT afeta a estrutura dos túbulos dentinários, a composição inorgânica da dentina intra-radicular e a integridade das fibras colágenas na dentina radicular, o que pode interferir na eficácia e durabilidade dos procedimentos odontológicos.

Comparison of the polishing effects of polyetheretherketone materials under different chairside polishing systems / 口腔疾病防治

Objective @# The polishing effects of different compositions of chairside polishing systems on polyetheretherketone (PEEK) were compared to provide a reference for the rational selection of polishing systems for this material in clinical settings. @*Methods @#A total of 108 specimens were made from ShushijieTMPEEK crown and bridge materials, Bio-PAEK® dental PEEK, and BioHPP® PEEK. Thirty-six specimens of each material were randomly divided into 6 groups on average based on their polishing technique: OptiDisc®, Super-Snap® Rainbow Technique Kit, VITA ENAMIC®Clinical Polishing Set, Sof-LexTM Diamond Polishing System, Visio.lign Finishing Kit for Composite Veneers, and CERAMAGE Polishing Kit, LavaTM Ultimate ceramic and VITA ENAMIC ceramics were set as the control groups, and 6 specimens were made in each material, polished by Sof-LexTM Diamond Polishing System and VITA ENAMIC® Polishing Set clinical, respectively, according to the manufacturers’ suggestions. The surface roughness (Ra value and Sa value) and gloss of each set were measured. The surface morphologies of the polished specimens were observed by scanning electron microscopy.@*Results @#Surface roughness (Ra value and Sa value) and gloss were mainly influenced by the type of polishing system, and they varied between PEEK material types. The Sof-LexTM Diamond Polishing System produced the highest surface roughness and the lowest gloss values for PEEK materials, while the Super-Snap® Rainbow Technique Kit, Visio.lign Finishing Kit for Composite Veneers and CERAMAGE Polishing Kit resulted in low surface roughness values. The Visio.lign Finishing Kit for Composite Veneers and CERAMAGE Polishing Kit exhibited high gloss values. Polishing paste particles were observed embedded on the surfaces of the PEEK materials polished by the Visio.lign Finishing Kit for Composite Veneers; the surfaces of specimens polished by the CERAMAGE Polishing Kit were smooth, without polishing paste particle residue. Using the same polishing system, the best polishing results were obtained with BioHPP® among the PEEK materials tested. The surface roughness values of the three tested PEEK materials polished by the CERAMAGE Polishing Kit were similar to those of the LavaTM Ultimate ceramic and VITA ENAMIC ceramic, but the gloss was higher than that of both. @*Conclusion @# CERAMAGE Polishing Kit was recommended for polishing all three tested PEEK materials, achieving a good polishing effect, with similar surface roughness and higher gloss characteristics comparable to those of polished computer-aided design and manufacturing (CAD/CAM) resin-matrix ceramics.

Scanning electron microscopic observation of morphology of Rhipicephalus sanguineus at different developmental stages in Hainan Province / 中国热带医学

@#Abstract: Objective To understand the morphological characteristics and ultrastructure of the dominant species of Rhipicephalus sanguineus in Hainan at different developmental stages, and provide theoretical basis for the identification of the lineage and control of Rhipicephalus sanguineus. Methods The external morphology of different developmental stages of the dominant species of Rhipicephalus sanguineus, including larva, nymph and adult tick in Hainan were observed by scanning electron microscope. Results The division between each segment of larva pedipalps was not obvious, and setae was serrated; dental formula type 2 | 2; 3 pairs of podomere; a pair of setae on the anal valve; none of anal groove, spiracular plate, porous area and genital aperture. There was a clear boundary at the beginning of each segment of nymph pedipalps; dental formula type 2 | 2; 4 pairs of podomere; 3 pairs of setae on the anal valve; anal groove; none of porous area and genital aperture. The male adult tick's trichotheca are covered by the pedipalps, and the whole bristles are conical; dental formula type 3 | 3; 4 pairs of podomere; anal groove and paraprocts; 7 setae on the anal valve; genital aperture was oval. The female of adult tick can be distinguished by dental formula 3 | 3; pairs of podomere; porous areas with 3 short setae; anal groove; 4 pairs of setae and 2 pores on the anal valve; genital pore was broadly U-shaped. In addition, the male adult's scutum occupies almost the entire dorsal surface, the basis capituli of larva, nymph and adult tick all were hexagonal, and the existence of Haller's organ was found on the first pair of legs. Conclusions Scanning electron microscopy observation of the different developmental stages of R.sanguineus revealed clear morphological features, preliminarily suggesting that R.sanguineus in Hainan Province may belong to the tropical lineage, which provide a certain experimental basis for the identification of the tick and the comprehensive prevention and control of local tick-borne diseases.

Wild hosts and microscopic worlds: Investigating the morphology and surface ultrastructure of Blastocystis sp. in avian and non-human primate species

@#Blastocystis is a prevalent infectious agent found in the gastrointestinal tract of humans and animals. While the morphology of Blastocystis has been extensively studied, there is still a lack of comprehensive research on its ultrastructure, especially regarding surface characteristics and their correlation with pathogenic potential. Additionally, the subtyping of Blastocystis does not provide information on the isolate’s pathogenicity. This study aimed to examine the morphology and the cell surface of Blastocystis in avian and non-human primates, including peafowl, pheasant, and lion-headed tamarin. By employing light microscopy and scanning electron microscopy (SEM), this study provides the first evidence of the cellular and surface features of Blastocystis in these animal species. Our findings revealed distinct variations in cell size, shape, and surface morphology among the different host species. Notably, the isolates from peafowl exhibited larger cell sizes compared to the isolates from the pheasant. However, interestingly, both animal species were found to exhibit the same Blastocystis ST6. It was also observed that the surface structure of Blastocystis from different hosts displayed a diverse range of patterns, including mesh-like appearances, deep indentations, and attachments to bacteria. Additionally, findings also revealed the presence of a rough surface structure in peafowl, a characteristic that has been previously linked to pathogenicity and symptomatic infection in animals, as indicated by earlier studies. The findings contribute to our understanding of the morphological features and the surface characteristic of Blastocystis in different host species, shedding light on the parasite’s adaptations and potential implications for host health.

Glyphosate-resistant hairy fleabane (Conyza bonariensis) exhibits a larger number of trichomes and altered stomatal density relative to the susceptible counterpart

Following the adoption of Roundup Ready crops, glyphosate spraying frequency increased, while the use of other herbicide modes of action was neglected. Herbicide-resistant biotypes were reported in three major Conyza species in Brazil, including Conyza bonariensis, increasing growers' bottom line. Considering that leaf surface structures affect proper herbicide deposition, uptake, and performance, this study aimed to characterize epicuticular surface components in glyphosate-resistant (R) and -susceptible (S) C. bonariensis. Conyza spp. seeds were collected in 36 locations in Brazil, and plants were subjected to resistance screening tests by spraying glyphosate at 720 and 1440 g ae ha-1 (0.5X and 1X the label recommended rate, respectively). For resistance level characterization, C. bonariensis biotypes with contrasting responses were selected for glyphosate dose-response assays. Leaf tissues for epicuticular surface analysis were harvested from newly-obtained R and S biotypes at two growth stages. Histological cuts were made on a leaf area of 25 mm² with a blade. Samples were fixed in Karnowsky solution, gradually changed to 100% ethanol, critical-point dried with CO2, and coated with gold, followed by stomatal and trichome density quantification using scanning electron microscopy. Results indicated a poor control with glyphosate in 33 of 36 Conyza spp. biotypes, and a high (31.5) resistance factor was calculated after dose-response trials. Leaf surface analysis indicated that C. bonariensis leaves are amphistomatic and exhibit tectorial trichomes. A higher number of trichomes and altered stomatal density (number.mm²) were quantified in R compared to the S counterpart, potentially reducing glyphosate uptake and effectiveness.

Final irrigation protocols can be used to promote stable long-term bond strength of AH Plus to dentin

Abstract Irrigation solutions might affect dentin surface characteristics and, consequently, endodontic sealers adhesion. Objective This study analyzed the effect of different final irrigation protocols on push-out bond strength (BS) of AH Plus to dentin seven days and 20 months after obturation. Scanning electron micrographs were obtained from the dentin surface of one sample/group after final irrigation. Methodology Canals of bovine incisors were instrumented and received final irrigation with (n=21): G1 - 2.5% sodium hypochlorite (NaOCl) + distilled water; G2 - 2.5% NaOCl + 17% EDTA; G3 - 2.5% NaOCl + 17% EDTA + 2.5% NaOCl; G4 - 2.5% NaOCl + 17% EDTA + 2% chlorhexidine (CHX); G5 - mixture 5% NaOCl + 18% etidronate (HEDP); and G6 - mixture 5% NaOCl + 10% tetrasodium EDTA (Na4EDTA). After irrigation, one root/group was split and images were obtained by scanning electron microscopy (SEM). The other 20 roots/group were filled with only AH Plus sealer. Three slices/root were used for push-out assessment seven days and 20 months after obturation. One-way analysis of variance and Tukey (α<0.05) were used to compare the results among experimental groups, and unpaired t-test (α<0.05) was used to compare the results of the same group over time. Results The photomicrographs showed that, excepting G1, all groups completely removed the smear layer from the samples. In G2 and G4, the opening of the dentin tubules enlarged. In G3, erosion was observed in the peritubular and intertubular dentin. Values of the BS in the seven days were G2=G3=G4=G5>G6=G1 and in the 20 months were G3=G5>G6=G4>G1=G2. G3, G5, and G6 presented values of BS in 20 months similar to the values of seven days (P>0.05). Conclusions The final irrigation protocols tested produced dentin surfaces with different characteristics. Only G3 and G5 presented high BS values that were stable over time.

Analysis of biofilm formation by Candida albicans in different types of orthodontic fixed appliances and devices / Análise da formação de biofilme por Candida albicans em diferentes tipos de aparelhos e dispositivos ortodônticos fixos

Objective: in this study, biofilm formation by Candida albicans in fixed orthodontic appliances was evaluated. Material and Methods: a total of 300 conventional metal brackets (MC), ceramic (CB), self-ligation (SLB), nickel-titanium (NiTi), and nickel-chromium (NiCr) wires, and ligatures types were organized into thirty groups (n=10). To induce biofilm formation, brackets, wires, and ligatures were joined, sterilized, placed in 24-well plates, contaminated with standardized suspensions of C. albicans (107 cells/mL), and incubated at 37 °C for 48 h with shaking. The biofilms formed were detached using an ultrasonic homogenizer, and suspensions were serially diluted and plated on Sabouraud dextrose agar to determine colony-forming units per mL. Scanning electron microscopy was performed before and after the biofilm formation. Results: lower amount of biofilm formation was observed in the MC group than in the CB and SLB groups (p<0.0001). SLB and CB showed similar biofilm formation rates (p=0.855). In general, the cross-sectional wires .018"x.025" showed higher biofilm formation when associated with the three types of brackets. When brackets, wires, and ligatures were associated, the sets with NiCr wires and SSL ligatures with MC brackets (p=0.0008) and CB (p=0.0003) showed higher biofilm formation. Conclusion: thus, brackets of MC with NiTi and NiCr wires showed lower biofilm formation, regardless of the ligature and cross-sectional or gauge of the wire and, MC and CB brackets with NiCr wires and SSL ligatures were more likely to accumulate biofilms (AU)

Objetivo: neste estudo, a formação de biofilme por Candida albicans em aparelhos ortodônticos fixos foi avaliada. Material e Métodos: um total de 300 bráquetes metálicos convencionais (MC), cerâmicos (CB), autoligados (SLB), com fios de níquel-titânio (NiTi) e níquel-cromo (NiCr) e tipos de ligaduras foram organizados em trinta grupos (n=10). Bráquetes, fios e ligaduras foram unidos, esterilizados, colocados em placas de 24 poços, contaminados com suspensões padronizadas de C. albicans (107 células/mL) e incubados a 37°C por 48 h para a formação de biofilmes. Os biofilmes formados foram rompidos por meio de um homogeneizador ultrassônico e suspensões foram diluídas e semeadas em ágar Sabouraud-dextrose para determinar as unidades formadoras de colônias por mL. A microscopia eletrônica de varredura foi realizada antes e após a formação do biofilme. Resultados: foi observada menor formação de biofilme no grupo MC em comparação aos grupos CB e SLB (p<0,0001). A formação de biofilme foi semelhante nos grupos SLB e CB (p=0,855). Em geral, os fios de seção transversal .018"x.025" apresentaram maior formação de biofilme quando associados aos três tipos de bráquetes. Os conjuntos com fios de NiCr e ligaduras SSL com bráquetes MC (p=0,0008) e CB (p=0,0003) apresentaram maior formação de biofilme. Conclusão: bráquetes MC com fios de NiTi e NiCr apresentaram menor formação de biofilme, independente da ligadura e secção transversal ou bitola do fio e, braquetes MC e CB com fios de NiCr e ligaduras SSL foram mais propensos a acumular biofilmes.(AU)