Extraction, recovery, and characterization of lignin from industrial corn stover lignin cake.

Lignin utilization in value-added co-products is an important component of enabling cellulosic biorefinery economics. However, aqueous dilute acid pretreatments yield lignins with limited applications due to significant modification during pretreatment, low solubility in many solvents, and high content of impurities (ash, insoluble polysaccharides). This work addresses these challenges and investigates the extraction and recovery of lignins from lignin-rich insoluble residue following dilute acid pretreatment and enzymatic hydrolysis of corn stover using three extraction approaches: ethanol organosolv, NaOH, and an ionic liquid. The recovered lignins exhibited recovery yields ranging from 30% for the ionic liquid, 44% for the most severe acid ethanol organosolv condition tested, and up to 86% for the most severe NaOH extraction condition. Finally, the fractional solubilities of different recovered lignins were assessed in a range of solvents and these solubilities were used to estimate distributions of Hildebrand and Hansen solubility parameters using a novel approach.

Spherical Crystallization Based on Liquid-Liquid Phase Separation in a Reverse Antisolvent Crystallization Process.

Vanillin crystals undergo needle-like morphology that results in poor flowability, crystal breakage, and low packing density. The spherical crystallization technology can produce particles with improved flowability and stability. A reverse antisolvent crystallization based on liquid-liquid phase separation is proposed in this work to produce vanillin spherical agglomerates. Hansen Solubility Parameters are applied to explain the liquid-liquid phase separation (LLPS) phenomenon. The Pixact Crystallization Monitoring system is applied to in-situ monitor the whole process. A six-step spherical crystallization mechanism is revealed based on the recorded photos, including the generation of oil droplets, nucleation inside oil droplets, the coalescence and split of oil droplets, crystal growth and agglomeration, breakage of oil droplets, and attrition of agglomerates. Different working conditions are tested to explore the best operation parameters and a frequency-conversion stirring strategy is proposed to improve the production of spherical crystals.

Are Hansen solubility parameters relevant in predicting the post-treatment effect on polyamide-based TFC membranes?

This study investigates the impact of solvent post-treatment on polyamide-based thin film composite (TFC) membranes, specifically examining the effect on commercial nanofiltration (NF) and reverse osmosis (RO) membranes. Na2SO4 rejection and increase in pure water permeance (PWP) were considered as the output parameters. The disparity in Hansen solubility parameters (HSP) between the post-treatment solution and the polyamide layer of the TFC membrane, denoted by Ra, is well adapted to understand the enhancement in water permeance through the membranes upon treatment. Aqueous solutions of dimethylformamide with a Ra value of 4, acetonitrile with a Ra value of 8.3, and ethanol with a Ra value of 12.7 were used as the post-treatment solutions. Our experimental design, based on the Box-Behnken design of Response Surface Methodology, incorporates variables such as the concentration of the solvent in the solution (% v/v), Ra value, and treatment time (s). Our findings demonstrate that the effect of post-treatment on the TFC membranes is not governed by the Ra value. Notably, while the post-treatment with the aqueous solution of acetonitrile, 80% v/v for 30 s, had considerable effects on NF membranes (124.5% enhancement in PWP; reduction of 3.5% in Na2SO4 rejection), its impact on RO membranes was negligible. Several factors explain this discrepancy, including the limitations of the HSP model for composite polymers, the inaccuracy of the PWP or salt rejection as a swelling indicator, variations in the HSP values of the polyamide layers for different membranes, and possible modifications in the interface between the support membrane and the polyamide layer. In summary, our study provides insights into the complex interactions between solvents and composite membranes, indicating that HSP alone is not a decisive factor in predicting post-treatment effects on polyamide-based TFC membranes.

Unfolding the Correlation between Solution Aggregation and Solid-State Crystal Orientation in Donor-Acceptor Copolymers via Solvent Additive Processing.

Tailoring the crystal orientation of donor-acceptor (D-A) copolymers is vital for boosting the performance of optoelectronic devices. Despite recent advances in controlling the crystal orientation of D-A copolymers in films, the investigation into their aggregates in solution and the correlation between the solution aggregates and solid-state crystal orientation has been limited. Herein, an effective solvent additive strategy is reported for tuning solution aggregates and the consequent solid-state structures of poly{[N,N'-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)} (P(NDI2OD-T2)). Specifically, the addition of 1-decanethiol (10-thiol) to the P(NDI2OD-T2) chloroform solution promoted the aggregation of P(NDI2OD-T2) chains because of the improved planarization of the backbones, which changed their crystal orientation in the film from coexisting edge-on and face-on to dominant edge-on when produced by drop-casting. The mechanism of this crystal orientation transformation is elucidated based on the interaction between 10-thiol and the side chains of P(NDI2OD-T2). The optical properties of P(NDI2OD-T2) films with different crystalline structures are closely correlated. Notably, the 10-thiol-enabled facile tailoring of the crystal orientation in P(NDI2OD-T2) can be readily applied to other D-A copolymers of interest. The findings of this study highlight a robust solvent additive strategy for regulating solution aggregates and crystal orientation in D-A copolymer films, which have applications in many optoelectronic devices.

A review on the calculation and application of lignin Hansen solubility parameters.

Hansen solubility parameters (HSPs) play a critical role in the majority of processes involving lignin depolymerization, separation, fractionation, and polymer blending, which are directly related to dissolution properties. However, the calculation of lignin HSPs is highly complicated due to the diversity of sources and the complexity of lignin structures. Despite their important role, lignin HSPs have been undervalued, attracting insufficient attention. This review summarizes the calculation methods for lignin HSPs and proposes a straightforward method based on lignin subunits. Furthermore, it highlights the crucial applications of lignin HSPs, such as identifying ideal solvents for lignin dissolution, selecting suitable solvents for lignin depolymerization and extraction, designing green solvents for lignin fractionation, and guiding the preparation of lignin-based composites. For instance, leveraging HSPs to design a series of solvents could potentially achieve sequential controllable lignin fractionation, addressing issues of low value-added applications of lignin resulting from poor homogeneity. Notably, HSPs serve as valuable tools for understanding the dissolution behavior of lignin. Consequently, we expect this review to be of great interest to researchers specializing in lignin and other macromolecules.

HSPiP and QbD Program-Based Analytical Method Development and Validation to Quantify Ketoconazole in Dermatokinetic Study.

Ketoconazole (KTZ) is the most potential azole anti-mycotic drug. The quantification of KTZ from various layers of the skin after topical application of lipidic nanocarriers is critical. We addressed a sensitive, specific, simple, rapid, reproducible, and economic analytical method to quantify KTZ from the treated skin homogenate using the Hansen solubility parameter (HSP, HSPiP software)-based modeling and experimental design. The software provided various HSP values for KTZ and solvents to compose the mobile phase. The Taguchi model identified the significant sets of factors to develop a robust bioanalytical method with reduced variability. In the optimization, acetonitrile (ACN) concentration (X1 as A) and the pH of mobile phase (X2 as B) were two factors against two responses (Y1: peak area and Y2: retention time). The HPLC (high-performance liquid chromatography) method validation was carried out based on US-FDA guidelines for the developed KTZ formulations (suspension, solid nanoparticles, and commercial product) extracted from the treated rat skin. The experimental solubility of KTZ was found to be maximum in the two solvents (ACN and ethyl acetate), based on HSP values. Surface response methodology (SRM) identified remarkable impact of ACN concentration and the mobile phase pH on the peak area and retention time. Analytical limits (0.17 and 0.50 µg/mL) were established for KTZ-SLNs (extracted from the skin). The method was implemented with high reproducibility, accuracy, and selectivity to quantify KTZ from the treated rat skin.

Experimental and theoretical estimation of the Hansen solubility parameters of paramylon esters based on the degrees of substitution and chain lengths of their acyl groups.

Paramylon is a natural hydrophilic polysaccharide produced in the pyrenoids of euglenoids, and esterification may render paramylon hydrophobic. Esterification imparts not only thermoplasticity, but also potential compatibilities with other polymer resins and fillers. However, the dependence of the compatibility on the structure of the polymer ester has not yet been systematically studied. To estimate the affinities between paramylon esters and hydrophobic organic solvents/resins, the dependences of their Hansen solubility parameters, which are association indices, on the degrees of substitution and chain lengths of the ester groups were investigated. Experimental and theoretical investigations were conducted using the dissolution and Fedors methods, respectively. Esterification decreased the solubility parameter from 49 (paramylon) to approximately 18 MPa1/2 (paramylon esters), indicating that the potential affinities of paramylon esters for hydrophobic organic solvents/polymers increased. A multiple regression analysis was also performed to investigate the effects of acyl chain length and degree of substitution with acyl groups on the solubility parameter. The solubility parameters of the paramylon derivatives were continuously variable from hydrophilic to -phobic. Hence, esterification with various acyl groups may control the hydrophobicities of paramylon esters, enhancing their miscibilities with various hydrophobic organic solvents and resins.

Optimization of antioxidant and lycopene extraction from tomato pomace using Hansen solubility parameters and its application in chicken meat preservation.

Tomato pomace, composed of peels and seeds, is often discarded or used as animal feed. However, it contains valuable phytochemicals, including lycopene. Lycopene, a natural pigment, is an antioxidant known for reducing the risk of chronic diseases like cardiovascular ailments and cancer. In this study, we aimed to study the possibility of valorizing tomato pomace by quantifying phenolic compounds, evaluating the antioxidant activity of their extracts, as well as extracting and quantifying lycopene, and studying the effect of tomato peel extract on the oxidative stability of chicken patties during storage. The effectiveness of different solvent mixtures for the extraction of lycopene was evaluated using Hansen solubility parameters (HSPs). The obtained results showed that the best solvent mixture was hexane/acetone (50/50) with a Hansen theoretical distance of 7.2, indicating its favorable solvation power. It also achieved a notable extraction yield of 3.12% and the highest lycopene yield of 20.05 mg/100 g. This combination demonstrated the highest values in terms of total phenolic (24.06 mg equivalent gallic acid/100 g dry matter) and flavonoid content (30.55 mg equivalent catechin/100 g dry matter), indicating a significant presence of these compounds. However, its 1,1-diphenyl-2-picrylhydrazyl (13.51 µg/mL) and ABTS, 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid, (8.52 µg/mL) IC50 values were comparatively lower than the other mixes. The use of this fraction as a food additive and antioxidant showed significant competitiveness with the conventional preservative, 2,6-di-tert-butyl-4-methylphenol. Tomato extract can be considered a potential natural preservative in food preparations due to its high lycopene content. PRACTICAL APPLICATION: This research provides valuable insights into optimizing the extraction of antioxidants from tomato pomace, using HSPs. The findings have the potential to benefit the food industry by developing improved methods for preserving chicken meat through the application of these optimized antioxidant extracts. By enhancing the preservation process, this study may contribute to extending the shelf life and maintaining the quality of chicken meat, leading to reduced food waste and improved consumer satisfaction.

Solubility of hesperidin drug in aqueous biodegradable acidic choline chloride-based deep eutectic solvents.

Important efforts have been made over the past years to improve the drug acts, which leads to the discovery of novel drug preparations and delivery systems. The selection of suitable green solvents for novel drug discovery and drug delivery depends on a molecular-level understanding of the interaction between drug molecules and the solvents. Deep eutectic solvents (DESs) are already used in sustainable extraction methods of natural products for their very high solvent power, high chemical and thermal stability, non-toxicity, and non-flammable. The thermodynamic investigation provides deep and complete knowledge of interactions and the choice of appropriate and suitable production compounds in pharmaceutical fields. Particularly, the analysis of drugs+DESs in aqueous media is a central issue in many types of research. This research is aimed to determine hesperidin (HES) solubility in water and DES solvents [choline chloride/citric acid (ChCl/CA), choline chloride/oxalic acid (ChCl/OA), choline chloride/malonic acid (ChCl/MA), and choline chloride/lactic acid (ChCl/LA)] at temperature range (298.15-313.15 K). Furthermore, the measured solubility data of HES in studied aqueous DESs solutions was fitted by models of Van't Hoff-Jouyban-Acree and Modified Apelblat-Jouyban-Acree. Finally, the Hansen solubility parameters as thermodynamic aspect for analyzing the dissolution processes for the four investigated aqueous DESs solutions were estimated.

A prediction system: Regulating effect of small-molecule additives on properties of amorphous solid dispersions prepared by hot-melt extrusion technology.

Amorphous solid dispersions (ASDs) with solubility advantage are suffering from the recrystallization risk and subsequent reduced dissolution triggered by high hygroscopicity of hydrophilic polymers and the supersaturation of ASD solutions. To address these issues, in this study, small-molecule additives (SMAs) in the Generally Recognized as Safe (GRAS) list were introduced into drug-polymer ASD. For the first time, we systematically revealed the intrinsic correlation between SMAs and properties of ASDs at the molecular level and constructed a prediction system for the regulation of properties of ASDs. The types and dosages of SMAs were screened by Hansen solubility and Flory-Huggins interaction parameters, as well as differential scanning calorimetry. X-ray photoelectron spectroscopy and adsorption energy (Eabs) calculation showed that the surface group distribution of ASDs and Eabs between ASD system and solvent were vital factors affecting the hygroscopicity and then stability. The radial distribution function revealed that interactions between components were proposed to be the critical factor for the dissolution performance. Based on this, a prediction system for regulating the properties of ASDs was successfully constructed mainly via molecular dynamics simulations and simple solid-state characterizations, and then validated by cases, which efficiently reduces the time and economic cost of pre-screening ASDs.

Alternatives to classic solvents for the isolation of bioactive compounds from Chrysochromulina rotalis.

This paper demonstrates a sequential partitioning method for isolating bioactive compounds from Chrysochromulina rotalis using a polarity gradient, replacing classic and hazardous solvents with greener alternatives. Seventeen solvents were evaluated based on their Hansen solubility parameters and for having a similar polarity to the solvents they would replace, four of which were selected as substitutes in the classic fractionation process. Considering the fatty acid and carotenoid recovery yields obtained for each of the solvents, it has been proposed to replace hexane (HEX), toluene (TOL), dichloromethane (DCM) and n-butanol (BUT) with cyclohexane, chlorobenzene, isobutyl acetate and isoamyl alcohol, respectively. In addition, cytotoxic activity was observed when the TOL and DCM solvent extracts were tested against tumour cell lines, demonstrating the antiproliferative potential of compounds containing, for example, fucoxanthin, fatty acids, peptides, isoflavonoids or terpenes, among others.

Multiscale molecular simulations for the solvation of lignin in ionic liquids.

Lignin, the second most abundant biopolymer found in nature, has emerged as a potential source of sustainable fuels, chemicals, and materials. Finding suitable solvents, as well as technologies for efficient and affordable lignin dissolution and depolymerization, are major obstacles in the conversion of lignin to value-added products. Certain ionic liquids (ILs) are capable of dissolving and depolymerizing lignin but designing and developing an effective IL for lignin dissolution remains quite challenging. To address this issue, the COnductor-like Screening MOdel for Real Solvents (COSMO-RS) model was used to screen 5670 ILs by computing logarithmic activity coefficients (ln(γ)) and excess enthalpies (HE) of lignin, respectively. Based on the COSMO-RS computed thermodynamic properties (ln(γ) and HE) of lignin, anions such as acetate, methyl carbonate, octanoate, glycinate, alaninate, and lysinate in combination with cations like tetraalkylammonium, tetraalkylphosphonium, and pyridinium are predicted to be suitable solvents for lignin dissolution. The dissolution properties such as interaction energy between anion and cation, viscosity, Hansen solubility parameters, dissociation constants, and Kamlet-Taft parameters of selected ILs were evaluated to assess their propensity for lignin dissolution. Furthermore, molecular dynamics (MD) simulations were performed to understand the structural and dynamic properties of tetrabutylammonium [TBA]+-based ILs and lignin mixtures and to shed light on the mechanisms involved in lignin dissolution. MD simulation results suggested [TBA]+-based ILs have the potential to dissolve lignin because of their higher contact probability and interaction energies with lignin when compared to cholinium lysinate.

Microporous Matrimid/PIM-1 Thin Film Composite Membranes with Narrow Pore Size Distribution used for Molecular Separation in Organic Solvents.

Polymers of intrinsic microporosity (PIMs) are a class of microporous organic materials that contain interconnected pores of less than 2 nm in diameter. Such materials are of great potential used in membranes for molecular separation, such as drug fractionation in pharmaceutical industry. However, the PIMs membranes are often susceptible to low separation selectivity toward different molecules due to their wide pore size distribution. Herein, a linear polyimide, Matrimid, is incorporated with PIM-1 (a typical member of PIMs) by solution blending, and the blends are dip-coated onto a polyimide P84 support membrane to prepare thin-film composite (TFC) membranes to control pore size distribution while keep high microporosity. The component miscibility, pore characteristics, and molecular separation performances of the Matrimid/PIM-1 TFC membranes are investigated in detail. The Matrimid and PIM-1 are partially miscible due to their similar Hansen solubility parameters. The Matrimid endows the selective layers (coatings) with narrower pore size distribution due to more compact chain packing. The prepared Matrimid/PIM-1 TFC membranes show high selectivity for separation of riboflavin (80% of retention) and isatin (only 5% of retention). The developed membranes exhibit great potential for separating molecules with different molecular weights.

Drug-Carrier Miscibility in Solid Dispersions of Glibenclamide and a Novel Approach to Enhance Its Solubility Using an Effervescent Agent.

The present research aims to investigate the miscibility, physical stability, solubility, and dissolution rate of a poorly water-soluble glibenclamide (GLB) in solid dispersions (SDs) with hydrophilic carriers like PEG-1500 and PEG-50 hydrogenated palm glycerides (Acconon). Mathematical theories such as Hansen solubility parameters, Flory Huggins theory, Gibbs free energy, and the in silico molecular dynamics simulation study approaches were used to predict the drug-carrier miscibility. To increase the solubility further, the effervescence technique was introduced to the conventional solid dispersions to prepare effervescent solid dispersions (ESD). Solid dispersions (SDs) were prepared by microwave, solvent evaporation, lyophilization, and hot melt extrusion (HME) techniques and tested for different characterization parameters. The theoretical and in silico parameters suggested that GLB would show good miscibility with the selected carriers under certain conditions. Intermolecular hydrogen bonding between the drug and carrier(s) was confirmed by Fourier transform infrared spectroscopy and proton nuclear magnetic resonance spectroscopy. Solid-state characterizations like powder X-ray diffraction, differential scanning calorimetry, and microscopy confirm the amorphous nature of SDs. The addition of the effervescent agent improved the amorphous nature, due to which the solubility and drug release rate was increased. In vitro and ex vivo intestinal absorption studies showed improved flux and permeability than the pure drug, suggesting an enhanced drug delivery. The GLB solubility, dissolution, and stability were greatly enhanced by the SD and ESD technology.

Experimental Examination of Solubility and Lipophilicity as Pharmaceutically Relevant Points of Novel Bioactive Hybrid Compounds.

The important physicochemical properties of three novel bioactive hybrid compounds with different groups (-CH3, -F and -Cl) were studied, including kinetic and thermodynamic solubility in pharmaceutically relevant solvents (buffer solutions and 1-octanol) as well as partition coefficient in system 1-octanol/buffer pH 7.4. The aqueous solubility of these chemicals is poor and ranged from 0.67 × 10-4 to 1.98 × 10-3 mol·L-1. The compounds studied are more soluble in the buffer pH 2.0, simulating the gastrointestinal tract environment (by an order of magnitude) than in the buffer pH 7.4 modelling plasma of blood. The solubility in 1-octanol is significantly higher; that is because of the specific interactions of the compounds with the solvent. The prediction solubility behaviour of the hybrid compounds using Hansen's three-parameter approach showed acceptable results. The experimental solubility of potential drugs was successfully correlated by means of two commonly known equations: modified Apelblat and van't Hoff. The temperature dependencies of partition coefficients of new hybrids in the model system 1-octanol/buffer pH 7.4 as a surrogate lipophilicity were measured by the shake flask method. It was found that compounds demonstrated a lipophilic nature and have optimal values of partition coefficients for oral absorption. Bioactive assay manifested that prepared compounds showed antifungal activities equal to or greater than fluconazole. In addition, the thermodynamic aspects of dissolution and partition processes have been examined. Bioactive assay manifested that prepared compounds showed antifungal activities equal to or greater than the reference drug.

Application of perfluoropolyether elastomers in microfluidic drug metabolism assays.

Recently, increasing attention has been paid to liver-on-a-chip models for both pharmacokinetics and toxicity (ADMET) screenings. Although polydimethylsiloxane (PDMS) is the most popular material for the fabrication of microfluidic devices, its extensive sorption of hydrophobic drugs limits its applications. Therefore, we investigated a chemically repellent material, perfluoropolyether (PFPE) elastomer, as an alternative to PDMS. Primary rat hepatocytes cultured in the PFPE microfluidic device were polygonal or cuboidal in shape and had one or two prominent nuclei, as when cultured in 96-well plates. When hepatocytes were cultured in the PFPE microfluidic device and exposed to dynamic flow, the production of albumin and urea increased 3.94- and 1.72-fold, respectively, compared with no dynamic flow. Exposure to dynamic flow did not result in obvious changes in the expression of cytochrome P450, but increased the metabolic activity of hepatocytes compared to under static conditions. PFPE devices did not absorb midazolam, which was extensively absorbed by PDMS devices. However, the sorption of bufuralol could not be avoided even with PFPE devices. Solvent swelling experiments highlighted much better chemical repellency with PFPE than with PDMS. Hansen solubility parameters and sphere radius were estimated from the solvent swelling experiments. The relative energy distance (RED) of bufuralol to PFPE was much smaller than that of other three drugs tested, reasonably explaining the high sorption of bufuralol to PFPE. Although sorption into PFPE cannot be completely avoided, PFPE microfluidic devices may provide a better performance in ADMET evaluation than PDMS.

Valorization of distillery stillage by polyphenol recovery using microwave-assisted, ultrasound-assisted and conventional extractions.

An increasing understanding of the negative environmental effects of waste discharges has made valorization of distillery by-products to recover added-value compounds a sound option for distillery stillage management. In this study, the recovery of bioactive compounds, i.e. polyphenols, from distillery stillage was performed by microwave-assisted extraction (MAE), ultrasound-assisted extraction (UAE) and conventional solid-liquid extraction (CSLE) to investigate the effects of extraction time, the concentration of ethyl acetate (EA) in a solvent mixture with ethanol and water, and solid-to-solvent ratio on the recovery yield and antioxidant activity of the extracts. The highest yields of total polyphenol content (TPC) (3.73 mg gallic acid equivalent/g) and phenolic acid content (2.51 µg/g) were obtained with 8-min MAE with 70% EA. MAE provided 1.2- and 1.4-times higher yield of phenolic acids and 1.2- and 1.6-times higher antioxidant activity than UAE and CSLE, respectively. Due to the approximately 3-times higher rate of extraction, the ratio between energy consumption and extraction yield was better in MAE than in UAE. Principal component analysis (PCA) showed that the antioxidant activity of the extracts was positively correlated with TPC and phenolic acid content. Six phenolic acids that were identified were present mainly in their free forms (up to 95% of the total), with a predominance of ferulic (up to 0.80 µg/g) and p-coumaric (up to 0.72 µg/g) acids.

Self-assembled zein organogels as in situ forming implant drug delivery system and 3D printing ink.

Recently, biomedical applications of organogels have been increasing; however, there is a demand for bio-based polymers. Here, we report self-assembled zein organogels in N-methyl pyrrolidone (NMP), Dimethyl sulfoxide (DMSO), and glycerol formal (GF). The gel formation was driven by the solvent's polarity and the hydrogen bonding component of Hansen Solubility Parameters was important in promoting gelation. Gels exhibited shear-thinning and thixotropic properties. Furthermore, water-induced self-assembly of zein allows mechanically robust in situ implant formation by solvent exchange. Ciprofloxacin was incorporated as a model drug and sustained release depending upon the solvent exchange rate was observed. In situ implants in agarose gel retained antibacterial efficacy against S. aureus for more than 14 days. Zein-based organogels were further applied as 3D printing ink and it was found that zein gel in DMSO had superior printability than gels prepared in NMP and GF. Using three solvents to prepare organogels can enable the encapsulation of various drugs and facilitate the preparation of composite gels with other biocompatible polymers. These organogel systems can further be used for developing 3D printed drug delivery systems or scaffolds for tissue engineering.

Application of COSMO-RS-DARE as a Tool for Testing Consistency of Solubility Data: Case of Coumarin in Neat Alcohols.

Coumarin is a naturally occurring lactone-type benzopyrone with various applications in the pharmaceutical, food, perfume, and cosmetics industries. This hydrophobic compound is poorly soluble in water but dissolves well in protic organic solvents such as alcohols. Despite the extensive use of coumarin, there are only a few reports documenting its solubility in organic solvents, and some reported data are incongruent, which was the direct impulse for this study. To resolve this problem, a theoretical congruency test was formulated using COSMO-RS-DARE for the determination of intermolecular interaction parameters, which allowed for the identification of outliers as suspicious datasets. The perfect match between back-computed values of coumarin solubility and the experimental ones confirms the reliability of the formulated theoretical approach and its adequacy for testing solubility data consistency. As the final approval, the temperature-related coumarin solubility in seven neat alcohols was determined experimentally. Four solvents (methanol, ethanol, 1-propanol, and 2-propanol) were used for reproducibility purposes, and an additional three (1-butanol, 1-pentanol, and 1-octanol) were used to extend the information on the homologous series. The consistency of this extended solubility dataset is discussed in terms of the comparison of remeasured solubility values with the ones already published and within the series of structurally similar solvents. The proposed procedure extends the range of applicability of COSMO-RS-DARE and provides a real and useful tool for consistency tests of already published solubility data, allowing for the approval/disapproval of existing data and filling gaps in datasets. Linear regressions utilizing a 2D molecular descriptor, SpMin2_Bhm, or the distance between solute and solvent in the Hansen solubility space, Ra, were formulated for the estimation of COMSO-RS-DARE integration parameters.

Green Solvent Cleaning Removes Irrecoverable Foulants from End-of-Life Membranes in Membrane Bioreactors: Efficacy and Mechanisms.

Removal of irrecoverable foulants, which cannot be removed by conventional chemical cleaning, from end-of-life (EOL) membranes remains a substantial challenge due to the strong interaction between the foulants and membrane matrix. Herein, we developed a green solvent cleaning strategy based on Hansen solubility parameters to achieve the removal of irrecoverable foulants from the EOL polyvinylidene fluoride (PVDF) membranes serving for 6 years in a large-scale membrane bioreactor (MBR). We selected methyl-5-(dimethylamino)-2-methyl-5-oxopentanoate (MDMO) as the green solvent due to its strong interaction with the PVDF material, which might enable the substitution of binding sites of irrecoverable foulants. After the MDMO cleaning, the water permeance of the EOL membrane recovered from 47.6 ± 4.7 to 390.9 ± 8.2 L m-2 h-1 bar-1 (with a flux recovery ratio of ∼100%), with its rejection ability and stability maintained. The main components of irrecoverable fouling were humic acid-like substances revealed by spectroscopic characterization. Molecular dynamic simulation further elucidated the cleaning mechanisms: the strong interaction of MDMO-PVDF enabled substitution of binding sites of irrecoverable foulants by MDMO, followed by desorption of the irrecoverable foulants from PVDF and diffusion of the irrecoverable foulants into the bulk phase of MDMO. Evaluation in a lab-scale MBR treating real municipal wastewater verified the reusability of green solvent cleaned-EOL membranes. This study provides a novel, effective, and green cleaning strategy to remove irrecoverable foulants and prolong the service life of membranes in MBRs, facilitating sustainable wastewater treatment using membrane-based processes.