Antibacterial activity of the noni fruit extract against Listeria monocytogenes and its applicability as a natural sanitizer for the washing of fresh-cut produce.

This study was conducted to investigate the antibacterial activity of the noni fruit extract (NFE) against Listeria monocytogenes (ATCC, 19111 and 19115) and assess its applicability for the washing of fresh-cut produce. Based on the results of the disc diffusion test, L. monocytogenes (ATCC, 19111 and 19115) was susceptible to the activity of NFE than other pathogens studied. Additionally, results of the time-kill assay indicated that NFE at a concentration of 0.5-0.7% effectively killed L. monocytogenes within 7 h. Furthermore, analysis of the intracellular components such as nucleic acids and proteins released from the bacterial cells and their SEM imaging revealed that NFE could increase the membrane permeability of cells resulting in their death. Compared to their unwashed samples, washing of romaine lettuce, spinach, and kale with 0.5% NFE gave a reduction of 1.47, 2.28, and 3.38 log CFU/g, respectively against L. monocytogenes (ATCC, 19111 and 19115), which is significantly different to that of NaOCl. A significant correlation was observed between the antibacterial effect induced due to NFE washing with the surface roughness of the fresh-cut produce than its surface hydrophobicity. Moreover, washing with NFE was not found to affect the color of the samples. These results indicated that NFE demonstrates good antibacterial activity against L. monocytogenes and can be used as a natural sanitizer to ensure the microbiological safety of fresh-cut produce.

Effect of black carbon on sorption and desorption of phosphorus onto sediments.

The sorption behavior of phosphorus onto sediment was investigated with the addition of BC derived from incomplete biomass combustion (PC). The sorption kinetic curves of phosphorus onto PC and sediment could be described by a two-compartment first order equation, and the sorption isotherms fit the Freundlich model well. With increasing amounts of PC added, the sorption capacity increased while the HI did not change much. The distribution of phosphorus forms showed that CaP (ACa-P plus DAP) constituted the highest fraction in the sediment samples. Throughout the sorption process, CaP and OP changed very little, but the Ex-P and FeP increased obviously, and the presence of PC made this increase more significantly. The high specific area and the presence of iron and aluminum, as well as the modification of the sediments surface properties, make the addition of PC be favorable for the sorption of phosphorus onto sediments.

AuNPs-PCL nanocomposite accelerated abdominal wound healing through photothermal effect and improving cell adhesion.

Accelerating wound healing with modified biomaterial has been an attracting field in both material science and medicine. Enhanced cell adhesion could be acquired by improving surface hydrophilicity, which contributes to accelerating wound healing. Chemical reaction has been used for surface modification, but this study used a simple and nontoxic method to improve the hydrophilicity. Polycaprolactone (PCL) scaffold has been regarded as promising material for wound healing while its surface is hydrophobic. Our study demonstrated enhanced hydrophilicity of PCL with AuNPs coating. AuNPs has good biocompatibility and excellent photothermal effect. The coating of AuNPs not only improved the cell adhesion, but also gave PCL the ability to inhibit the growth of bacteria. Animal study showed that the nanocomposites decreased lymphocytes and neutrophils, increased neovascularization and accelerated the abdominal wound healing, which was attributed to improved hydrophilicity and the antibacterial ability. In conclusion, we demonstrated that the nanocomposite could be used as a potential scaffold for cell adhesion and wound healing, and the role of AuNPs was highlighted as a kind of outstanding supplement.

Hydrothermally tailor-made chitosan fiber for micro-solid phase extraction of petroleum acids in crude oils.

Tailor-made chitosan fiber was prepared via hydrothermal treatment to serve as a micro-solid phase extraction (micro-SPE) sorbent for the analysis of petroleum acids (PAs) in crude oils. Chitosan fiber, which is commercial and cheap, has a diameter of about 10 µm and a length of a few centimeters. The fibrous property of the sorbent enables the micro-SPE to deal with viscous crude oil samples because of the low back-pressure during extraction, while the abundant hydroxyl groups and amino groups on the surface of chitosan fiber can provide high density of specific sites for adsorption of PAs. Moreover, it was found that hydrothermal treatment at certain conditions could tune the surface properties of chitosan fiber, leading to significant improvement of the capacity of the fiber in adsorption of PAs. Using hydrothermally treated chitosan fiber as sorbent, the micro-SPE was applied to the determination of PAs in crude oils, with the advantages of easy-operation, rapidness and high sensitivity (the limits of detection range from 0.7 ng/g to 5.4 ng/g). Furthermore, coupled with comprehensive two dimensional gas chromatography-mass spectrometry (GC × GCMS), the treated chitosan fiber packed micro-SPE method showed a great potential for comprehensive profiling of PAs in crude oils.

Characterization of phosphorus sorption on the sediments of Yangtze River Estuary and its adjacent areas.

This paper studied the kinetics, isotherm and thermodynamics of phosphorus sorption onto the sediments of the Yangtze River estuary and its adjacent waters, as well as the sediments' compositions and physicochemical properties. The process could be described well by a two-compartment first order equation. The sorbed phosphorus mainly consisted of Ex-P and Fe-P, with Ex-P being the dominant. The equilibrium isotherms could be fitted well with a modified Langmuir equation. The calculations of the thermodynamic parameters indicated that the process was spontaneous and exothermic. The CEC and the fractions of clay, calcite and organic matter were correlated with the sorption parameters, while the surface proton charge of the sediments was significantly negatively correlated with them. Considering the kinetics and phosphorus forms changes during the process, the sorption in our study could be considered that the physical process plays an important role.

In vitro osteogenic cell proliferation, mineralization, and in vivo osseointegration of injection molded high-density polyethylene-based hybrid composites in rabbit animal model.

The present work reports the biocompatibility property of injection molded HDPE-HA-Al2O3 hybrid composites. In vitro cytocompatibility results reveal that osteogenic cell viability and bone mineralization are favorably supported in a statistically significant manner on HDPE-20% HA-20% Al2O3 composite, in comparison to HDPE-40 wt.% HA or HDPE-40 wt.% Al2O3 The difference in cytocompatibility property is explained in terms of difference in substrate wettability/surface energy and importantly, both the cell proliferation at 7 days or bone mineralization at 21 days on HDPE-20% HA-20% Al2O3 composite are either comparable or better than sintered HA. The progressive healing of cylindrical femoral bone defects in rabbit animal model was assessed by implantation experiments over 1, 4 and 12 weeks. Based on the histological analysis as well as histomorphometrical evaluation, a better efficacy of HDPE-20% HA-20% Al2O3 over high-density polyethylene (HDPE) for bone regeneration and neobone formation at host bone-implant interface was established. Taken together, the present study unequivocally establishes that despite the presence of 20% Al2O3, HDPE-based hybrid composites are as biocompatible as HA in vitro or better than HDPE in vivo.