ABSTRACT
A novel binding layer (BL) as part of the diffusive gradients in thin films (DGT) technique was developed for the two-dimensional visualization and quantification of labile phosphorus (P) in soils. This BL was designed for P detection by synchrotron-based X-ray fluorescence microscopy (XFM). It differs from the conventional DGT BL as the hydrogel is eliminated to overcome the issue that the fluorescent X-rays of P are detected mainly from shallow sample depths. Instead, the novel design is based on a polyimide film (Kapton) onto which finely powdered titanium dioxide-based P binding agent (Metsorb) was applied, resulting in superficial P binding only. The BL was successfully used for quantitative visualization of P diffusion from three conventional P fertilizers applied to two soils. On a selection of samples, XFM analysis was confirmed by quantitative laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). The XFM method detected significant differences in labile P concentrations and P diffusion zone radii with the P fertilizer incubation, which were explained by soil and fertilizer properties. This development paves the way for fast XFM analysis of P on large DGT BLs to investigate in situ diffusion of labile P from fertilizers and to visualize large-scale P cycling processes at high spatial resolution.
Subject(s)
Fertilizers , Phosphorus , Phosphorus/analysis , Phosphorus/chemistry , Fertilizers/analysis , X-Rays , Soil/chemistry , Diffusion , Microscopy, FluorescenceABSTRACT
The nexus between green growth and ecological footprint is associated with crucial environmental implications. But this domain is not examined sufficiently and provides ambiguous findings. Furthermore, these studies have not addressed the role of natural resources, environmental innovation, and ICT in influencing ecological footprint. Our study analyzes the impact of green growth, ICT, environmental innovation, and natural resources on the ecological footprint ofemerging-7 and developed-7 economies. We employed CS-ARDL methodology to draw the long-run and short-run estimates of the said relationships. The obtained findings show that green growth, ICT, and environmental innovation reduce the ecological footprint in emerging economies in the long run. However, natural resources enhance the ecological footprint in emerging economies in the long run. Green growth, ICT, natural resources, and environmental innovation reduce the ecological footprint in the long run in developed economies. Based on these outcomes, the study recommends important policy suggestions.
Subject(s)
Gap Junctions , Natural Resources , Diffusion , Policy , SuggestionABSTRACT
Recent studies have developed varied delivery systems incorporating natural compounds to improve the limitations of plant extracts for clinical use while enabling their controlled release at treatment sites. For the first time, ethanolic limeberry extract (Triphasia trifolia) has been successfully encapsulated in thermo-sensitive chitosan hydrogels by a facile in situ loading. The extract-incorporated chitosan hydrogels have a pH value of nearly 7.00, gelation temperatures in the range of 37-38 °C, and exhibit an open-cell porous structure, thus allowing them to absorb and retain 756 % of their mass in water. The in vitro extract release from the hydrogels is driven by both temperature and pH, resulting in more than 70 % of the initial extract being released within the first 24 h. Although the release half-life of hydrogels at pH 7.4 is longer, their release capacity is higher than that at pH 6.5. Upon a 2 °C increase in temperature, the time to release 50 % initial extract is sharply reduced by 20-40 %. The release kinetics from the hydrogels mathematically demonstrated that diffusion is a prominent driving force over chitosan relaxation. Consequently, the developed hydrogels encapsulating the limeberry extract show their heat and pH sensitivity in controlled release for treating chronic wounds.
Subject(s)
Chitosan , Delayed-Action Preparations , Diffusion , Hydrogels , Hydrogen-Ion ConcentrationABSTRACT
Heteroatom doping is considered an effective method to substantially improve the electrochemical performance of Ti3C2Tx MXene for supercapacitors. Herein, a facile and controllable strategy, which combines heat treatment with phosphorous (P) doping by using sodium phosphinate (NaH2PO2) as a phosphorus source, is used to modify Ti3C2Tx. The intercalated ions from NaH2PO2 act as "pillars" to expand the interlayer space of MXene, which is conducive to electrolyte ion diffusion. On the other hand, P doping tailors the surface electronic state of MXene, optimizing electronic conductivity and reducing the free energy of H+ diffusion on the MXene surface. Meanwhile, P sites with lower electronegativity owning good electron donor characteristics are easy to share electrons with H+, which is beneficial to charge storage. Moreover, the adopted heat treatment replaces -F terminations with O-containing groups, which enhances the hydrophilicity and provides sufficient active sites. The change in surface functional groups increases the content of high valence-stated Ti with a high electrochemical activity that can accommodate more electrons during discharge. Synergistic modification of interlayer structure and chemical state improves the possibility of Ti3C2Tx for accommodating more H+ ions. Consequently, the modified electrode delivers a specific capacitance of 510 F g-1 at 2 mV s-1, and a capacitance retention of 90.2% at 20 A g-1 after 10,000 cycles. The work provides a coordinated strategy for the rational design of high-capacitance Ti3C2Tx MXene electrodes.
Subject(s)
Body Fluids , Titanium , Diffusion , PhosphorusABSTRACT
The results of the study of the physicochemical properties of the high-molecular-weight soluble and insoluble components of nectarine cell walls obtained by fruit treatment under conditions that modulate of gastric digestion are presented. Homogenized nectarine fruits were sequentially treated by natural saliva and simulated gastric fluid (SGF) at pH 1.8 and 3.0. The isolated polysaccharides were compared with polysaccharides obtained by sequential extraction of nectarine fruit with cold, hot, and acidified water, solutions of ammonium oxalate and sodium carbonate. As a result, high-molecular-weight water-soluble pectic polysaccharides, weakly bound in the cell wall, were dissolved in the simulated gastric fluid, regardless of pH. Homogalacturonan (HG) and rhamnogalacturonan-I (RG-I) were identified in all pectins. It was shown that their quantity and ability to form highly viscous solutions determine high values of the rheological characteristics of the nectarine mixture formed under simulated gastric conditions. The modifications occurring with the insoluble components under the influence of acidity of SGF were importance. They determined difference in the physicochemical properties of both the insoluble fibres and the nectarine mixtures.
Subject(s)
Cell Wall , Digestion , Fruit , Pectins , Prunus , Stomach , Adsorption , Cell Wall/chemistry , Dietary Fiber , Fruit/chemistry , Fruit/cytology , Glucose/metabolism , Hardness , Hydrogen-Ion Concentration , Pectins/chemistry , Pectins/isolation & purification , Prunus/chemistry , Rheology , Saliva/chemistry , Solubility , Stomach/chemistry , Viscosity , Water/analysis , Water/chemistry , DEAE-Cellulose , Particle Size , DiffusionABSTRACT
Effects of injection rate and tumor physiology on the diffusion of magnetic nano-particles (MNPs) and temperature profile during magnetic hyperthermia are investigated in this work. The study considers three injection rates (2.5 µL/min, 10 µL/min, and 40 µL/min), and two MNP diffusion coefficients (10-9 m2/s and 10-11 m2/s). The simulation of this physics has been done on 3D tumor surrounded by healthy tissue. Transient MNP distribution in tissue is evaluated using Darcy's flow model and the MNP transport (convection-diffusion) equation. The temperature profile in the tumor model is computed by solving Penne's bioheat transfer equation (PBHTE). Results show tumors with high collagen content (with low MNP diffusivity) are more restrictive towards MNP transport than tumors having low collagen content. Thus, tumors with low MNP diffusivity need a higher injection rate to increase the homogeneity of MNP concentration as well as temperature profile during thermo-therapy. Results also show that, MNP fluid injected with a higher injection rate produces a more uniform MNP concentration up to greater depth than the lower injection rate.
Subject(s)
Hyperthermia, Induced , Neoplasms , Nanoparticles , Humans , Diffusion , Magnetic PhenomenaABSTRACT
Field measurements of Rn-222 fluxes from the tops and bottoms of compacted clay radon barriers were used to calculate effective Rn diffusion coefficients (DRn) at four uranium waste disposal sites in the western United States to assess cover performance after more than 20 years of service. Values of DRn ranged from 7.4 × 10-7 to 6.0 × 10-9 m2/s, averaging 1.42 × 10-7. Water saturation (SW) from soil cores indicated that there was relatively little control of DRn by SW, especially at higher moisture levels, in contrast to estimates from most steady-state diffusion models. This is attributed to preferential pathways intrinsic to construction of the barriers or to natural process that have developed over time including desiccation cracks, root channels, and insect burrows in the engineered earthen barriers. A modification to some models in which fast and slow pathway DRn values are partitioned appears to give a good representation of the data; 4% of the fast pathway was needed to fit the data regression. For locations with high Sw and highest DRn (and fluxes) at each site, the proportion of fast pathway ranged from 1.7% to 34%, but for many locations with lower fluxes, little if any fast pathway was needed.
Subject(s)
Radiation Monitoring , Radon , Uranium , Radon/analysis , Diffusion , Waste Disposal FacilitiesABSTRACT
Significance: Based on acoustic detection of optical absorption, photoacoustic tomography (PAT) allows functional and molecular imaging beyond the optical diffusion limit with high spatial resolution. However, multispectral functional and molecular PAT is often limited by decreased spectroscopic accuracy and reduced detection sensitivity in deep tissues, mainly due to wavelength-dependent optical attenuation and inaccurate acoustic inversion. Aim: Previous work has demonstrated that reversible color-shifting can drastically improve the detection sensitivity of PAT by suppressing nonswitching background signals. We aim to develop a new color switching-based PAT method using reversibly switchable thermochromics (ReST). Approach: We developed a family of ReST with excellent water dispersion, biostability, and temperature-controlled color changes by surface modification of commercial thermochromic microcapsules with the hydrophilic polysaccharide alginate. Results: The optical absorbance of the ReST was switched on and off repeatedly by modulating the surrounding temperature, allowing differential photoacoustic detection that effectively suppressed the nonswitching background signal and substantially improved image contrast and detection sensitivity. We demonstrate reversible thermal-switching imaging of ReST in vitro and in vivo using three PAT modes at different length scales. Conclusions: ReST-enabled PAT is a promising technology for high-sensitivity deep tissue imaging of molecular activity in temperature-related biomedical applications, such as cancer thermotherapy.
Subject(s)
Photoacoustic Techniques , Tomography, X-Ray Computed , Photoacoustic Techniques/methods , Acoustics , Temperature , Diffusion , Tomography/methodsABSTRACT
In this work, convective-dispersive and pore volume and surface diffusion models have been used to analyze Pb(II) adsorption from an aqueous solution over a nanostructured γ-alumina adsorbent in a packed bed adsorber. The models encompassing partial differential equation and a linear algebraic equation coupled with isotherm have been simulated in gPROMS using the backward finite difference approach. The predicted breakthrough curves of Pb(II) adsorption concerning flow rate, initial metal concentration, and bed height were matched with the experimental data. The accuracy of model predictions was analyzed through statistical measures such as coefficient of determination (R2), root mean square error, and chi-squared value. The simulation results also predicted the axial dispersion, distribution coefficient, mass transfer coefficient, pore volume, and surface diffusion coefficient, which are, otherwise, difficult to measure experimentally and, in turn, have been used to assess the mass transfer characteristics of continuous Pb(II) adsorption. Additionally, the values of breakthrough time, exhaustion time, adsorption column capacity, and mass transfer zone were determined as a function of flow rate, bed height, and initial metal concentration. Surface and pore volume diffusions (10-11-10-10 m2/s) apparently controlled the continuous adsorption process, with surface diffusion being dominant. The transport parameters evaluated in the current study could be beneficial for the large-scale Pb(II)/nanostructured γ-alumina adsorption system. As evident from the successful simulation, the developed gPROMS program can also be applied to other adsorbate/adsorbent systems with a slight modification concerning the operating parameters.
Subject(s)
Nanostructures , Water Pollutants, Chemical , Lead , Adsorption , Aluminum Oxide , DiffusionABSTRACT
Nara sumi is a traditional Japanese craft that has been handed down in Nara since ancient times, and now plays a major role as a regional resource. Soot is considered to be one of the most important materials for its quality. However, the making process has been supported solely by the rule of thumb for craftsmen for many years, and there is very little scientific understanding of that. Therefore, we are focusing on the soot formation process in this study. Soot was collected from different heights in a rapeseed oil-fueled diffusion flame and analyzed by scanning electron microscopy and X-ray photoelectron spectroscopy. As a result, it was confirmed that the formation of the soot shape completes at the bottom of the outside of the flame and that the shape does not change thereafter. It was also confirmed that the oxidation of soot occurs at the bottom of the outside of the flame. These results are expected to contribute to the further scientific understanding of the soot formation process.
Subject(s)
Soot , Diffusion , Particle Size , Photoelectron Spectroscopy , Rapeseed OilABSTRACT
Approximate computing is an upsurging technique to accelerate the process through less computational effort while keeping admissible accuracy of error-tolerant applications such as multimedia and deep learning. Inheritance properties of the deep learning process aid the designer to abridge the circuitry and also to increase the computation speed at the cost of the accuracy of results. High computational complexity and low-power requirement of portable devices in the dark silicon era sought suitable alternate for Complementary Metal Oxide Semiconductor (CMOS) technology. Gate Diffusion Input (GDI) logic is one of the prompting alternatives to CMOS logic to reduce transistors and low-power design. In this work, a novel energy and area efficient 1-bit GDI-based full swing Energy and Area efficient Full Adder (EAFA) with minimum error distance is proposed. The proposed architecture was constructed to mitigate the cascaded effect problem in GDI-based circuits. It is proved by extending the proposed 1-bit GDI-based adder for different 16-bit Energy and Area Efficient High-Speed Error-Tolerant Adders (EAHSETA) segmented as accurate and inaccurate adder circuits. The proposed adder's design metrics in terms of delay, area, and power dissipation are verified through simulation using the Cadence tool. The proposed logic is deployed to accelerate the convolution process in the Low-Weight Digit Detector neural network for real-time handwritten digit classification application as a case study in the Intel Cyclone IV Field Programmable Gate Array (FPGA). The results confirm that our proposed EAHSETA occupies fewer logic elements and improves operation speed with the speed-up factor of 1.29 than other similar techniques while producing 95% of classification accuracy.
Subject(s)
Deep Learning , Multimedia , Computer Simulation , Diffusion , SemiconductorsABSTRACT
1H spin-lattice relaxation experiments have been performed for a series of ionic liquids including bis(trifluoromethanesulfonyl)imide anion and cations of a varying alkyl chain length: triethylhexylammonium, triethyloctylammonium, decyltriethylammonium, dodecyltriethylammonium, triethyltetradecylammonium, and hexadecyltriethylammonium. The relaxation studies were carried out in abroad frequency range covering three orders of magnitude, from 10 kHz to 10 MHz, versus temperature. On the basis of a thorough, quantitative analysis of this reach data set, parameters characterizing the relative, cation-cation, translation diffusion (relative diffusion coefficients and translational correlation times), and rotational motion of the cation (rotational correlation times) were determined. Relationships between these quantities and their dependence on the alkyl chain length were discussed in comparison to analogous properties of molecular liquids. It was shown, among other findings, that the ratio between the translational and rotational correlation times is smaller than for molecular liquids and considerably dependent on temperature. Moreover, a comparison of relative and self-diffusion coefficients indicate correlated translational dynamics of the cations.
Subject(s)
Ionic Liquids/chemistry , Quaternary Ammonium Compounds/chemistry , Diffusion , Magnetic Resonance Spectroscopy , Relaxation , TemperatureABSTRACT
The dynamics of the organic components of the deep eutectic solvent (DES) glyceline are analyzed using an array of complementary nuclear magnetic resonance (NMR) methods. Fast-field cycling 1H relaxometry, pulsed field gradient diffusion, nuclear overhauser effect spectroscopy (NOESY), 13C NMR relaxation, and pressure-dependent NMR experiments are deployed to sample a range of frequencies and modes of motion of the glycerol and choline components of the DES. Generally, translational and rotational diffusion of glycerol are more rapid than those of choline while short-range rotational motions observed from 13C relaxation indicate slow local motion of glycerol at low choline chloride (ChCl) content. The rates of glycerol and choline local motions become more similar at higher ChCl. This result taken together with pressure-dependent NMR studies show that the addition of ChCl makes it easier to disrupt glycerol packing. Finally, a relatively slow hydroxyl H-exchange process between glycerol and choline protons is deduced from the data. Consistent with this, NOESY results indicate relatively little direct H-bonding between glycerol and choline. These results suggest that the glycerol H-bonding network is disrupted as choline is added, but primarily in regions where there is intimate mixing of the two components. Thus, the local dynamics of most of the glycerol resembles that of pure glycerol until substantial choline chloride is present.
Subject(s)
Choline , Glycerol , Choline/chemistry , Diffusion , Glycerol/chemistry , Magnetic Resonance Spectroscopy , Solvents/chemistryABSTRACT
ß-carotene is a natural compound with immense healthcare benefits. To overcome insolubility and lack of stability which restricts its application, in this study, ß-carotene from Planococcus sp. TRC1 was entrapped into formulations of chitosansodium alginate microspheres (MF1, MF2 and MF3) and chitosan nanoparticles (NF1, NF2 and NF3). The maximum entrapment efficiency (%) and loading capacity (%) were 80.6 ± 4.28 and 26 ± 3.05 (MF2) and 92.1 ± 3.44 and 41.86 ± 4.65 (NF2) respectively. Korsmeyer-Peppas model showed best fit with release, revealing non-Fickian diffusion. Thermal and UV treatment exhibited higher activation energy (kJ/mol), 17.76 and 15.57 (MF2) and 37.03 and 19.33 (NF2) compared to free ß-carotene (3.7 and 3.9), uncovering enhanced stability. MF2 and NF2 revealed swelling index (%) 721 ± 1.7 and 18.1 ± 1.5 (pH 6.8) and particle size 69.5 ± 3.2 µm and 92 ± 2.5 nm respectively. FESEM, FT-IR, XRD and DSC depicted spherical morphology, intactness of functional groups and masking of crystallinity. The IC50 (µg ml-1) values for antioxidant and anticancer (A-549) activities were 33.1 ± 1.7, 45.1 ± 2.8, 39.3 ± 2.9 and 31.3 ± 1.7, 27.9 ± 2.4, 25.3 ± 2.2 for ß-carotene, MF2 and NF2 respectively with no significant cytotoxicity on HEK-293 cells and RBCs (p > 0.05). This comparative study of microspheres and nanoparticles may allow the diverse applications of an unconventional bacterial ß-carotene with promising stability and efficacies.
Subject(s)
Chitosan/chemistry , Drug Delivery Systems/methods , beta Carotene/pharmacology , Alginates/chemistry , Chemistry, Pharmaceutical , Diffusion , Drug Carriers/chemistry , Drug Compounding/methods , HEK293 Cells , Humans , Microspheres , Nanoparticles , Particle Size , Planococcaceae/metabolism , Spectroscopy, Fourier Transform Infrared/methods , beta Carotene/administration & dosageABSTRACT
Resveratrol (RSV) is a lipophilic polyphenol susceptible to photo- and thermal degradation, and strategies are to be studied to enable its distribution in food matrices, prevent its degradation during storage, and increase its bioaccessibility during digestion. In this study, the porous matrix of natural starch, in the form of milled freeze-dried potato microparticles (FDPMs), was studied as an absorbent to load RSV. The binary solvent of ethanol and polyethylene glycol 400 (40:60 v/v) was used to dissolve 30% w/v RSV for diffusion into FDPMs. After ethanol was evaporated, the loading capacity was 112 mg RSV/g FDPMs and was maintained at 104 mg RSV/g FDPMs (92.9% retention) after 110-day ambient storage. The RSV stability under UV irradiation at 253 nm was improved by 32% due to shielding effect of FDPMs, and the ferric reducing power was 25% higher than the pristine RSV. The release of RSV in FDPMs was significantly higher than pristine RSV during simulated gastric and intestinal digestions (82.3% vs 51.4% bioaccessibility). The increased reducing power and bioaccessibility were supported by the amorphous state of RSV in FDPMs. The present study illustrates the potential of porous vegetable microparticles as natural matrices to load lipophilic bioactive compounds in functional foods.
Subject(s)
Microspheres , Resveratrol/chemistry , Resveratrol/pharmacology , Starch/chemistry , Biopolymers/chemistry , Chemical Phenomena , Diffusion , Drug Carriers , Drug Stability , Porosity , Solanum tuberosum , Spectrum Analysis , ThermodynamicsABSTRACT
Monitoring of uranium in the environment using the Diffusive Gradients in Thin-films (DGT) technique gains in importance as it can provide unique information about the bioavailability of the element and allows its long-term in-situ measurement. Hence, in this study, four DGT binding phases (Chelex-100, Dow-PIWBA, Diphonix, and Lewatit FO 36 resins) were evaluated for uranium monitoring to assess the robustness of their performance in estuarine and marine environments. These DGTs were deployed along the Scheldt estuary (Belgium and the Netherlands) over four campaigns between 2014 and 2021. The DGT performance (ratio of the DGT-determined vs. dissolved U concentration in grab water sample) varied with the water salinity. The Chelex-100 DGTs generally provided good performance in freshwater (median ratios close to 1.0), but an inverse correlation with the increasing salinity was observed (median ratios 0.7 at the stations with salinity >5). The Lewatit FO 36 DGTs provided good performance in the salinity range 0-18 (median ratios 1.0). However, a strong negative influence was observed at stations with high salinity levels (>18, ratio 0.6) and during the long-term deployment in seawater (ratios <0.5 over deployment periods ≥2 days). The Dow-PIWBA and Diphonix DGTs provided overall similar results with excellent performances along the whole salinity gradient (median ratios 1.1 and 1.0, respectively). Nevertheless, the long-term deployment trial in seawater (salinity â¼27) revealed the robustness of Diphonix DGTs that provided outstanding results even after 28 days of deployment (ratio 1.0). The differences in the performance of tested DGT resins were mostly given by the changes of U speciation along the salinity gradient. The speciation modelling of U showed that calcium uranyl carbonate complexes dominate along the Scheldt estuary (from 97 to 86% seawards) with increasing fraction of UO2(CO3)34- (from 2 to 14%) towards the mouth.
Subject(s)
Uranium , Water Pollutants, Chemical , Diffusion , Environmental Monitoring , Estuaries , Gels , Polystyrenes , Polyvinyls , Salinity , Uranium/analysis , Water Pollutants, Chemical/analysisABSTRACT
Uranium tailing ponds are a potential major source of radioactive pollution. Solidification treatment can control the diffusion and migration of radioactive elements in uranium tailings to safeguard the surrounding ecological environment. A literature review and field investigation were conducted in this study prior to fabricating 11 solidified uranium tailing samples with different proportions of PVA fiber, basalt fiber, metakaolin, and fly ash, and the weight percentage of uranium tailings in the solidified body is 61.11%. The pore structure, volume resistivity, compressive strength, radon exhalation rate variations, and U(VI) leaching performance of the samples were analyzed. The pore size of the solidified samples is mainly between 1 and 50 nm, the pore volume is between 2.461 and 5.852 × 10-2 cm3/g, the volume resistivity is between 1020.00 and 1937.33 Ω·m, and the compressive strength is between 20.61 and 36.91 MPa. The radon exhalation rate is between 0.0397 and 0.0853 Bq·m-2·s-1. The cumulative leaching fraction of U(VI) is between 2.095 and 2.869 × 10-2 cm, and the uranium immobilization rate is between 83.46 and 85.97%. Based on a comprehensive analysis of the physical and mechanical properties, radon exhalation rates, and U(VI) leaching performance of the solidified samples, the basalt fiber is found to outperform PVA fiber overall. The solidification effect is optimal when 0.6% basalt fiber is added.
Subject(s)
Extraction and Processing Industry , Radioactive Waste , Soil Pollutants, Radioactive , Uranium , Waste Management , Coal Ash/analysis , Diffusion , Hazardous Waste Sites , Radiation Protection/methods , Radioactive Waste/analysis , Radon/analysis , Silicates/analysis , Soil Pollutants, Radioactive/analysis , Soil Pollutants, Radioactive/chemistry , Uranium/analysis , Waste Management/methodsABSTRACT
Geological media are omnipresent in nature. Lab-scale tests are frequently employed in radon exhalation measurements for these media. Thus, it is critical to find the thickness of the medium at an experimental scale that is equivalent to the medium thickness in a real geological system. Based on the diffusion-advection transport of radon, theoretical models of the surface radon exhalation rate for homogeneous semi-infinite and finite-thickness systems were derived (denoted as Jse and Jfi, respectively). Analysis of the equivalency of Jse and Jfi was subsequently carried out by introducing several dimensionless parameters, including the ratio of the exhalation rates for the semi-infinite and finite-thickness models, ε, and the number of diffusion lengths required to achieve a desired ε value, n. The results showed that when radon transport in geological media is dominantly driven by diffusion effect, if n > 3.6626, then ε > 95%; if n > 5.9790, then ε > 99.5%. When radon migration is dominantly driven by advection effect, if n > 2.5002, then ε > 95%; if n > 4.0152, then ε > 99.5%. Therefore, if the thickness of the geological media (x0) is greater than a certain n times the radon diffusion length of the media (L), the media can be modeled as semi-infinite. To validate the model, a pure radon diffusion experiment (no advection) was developed using uranium mill tailings, laterite, and radium-bearing rocklike material with different thicknesses (x0). The theoretical model was demonstrated to be reliable and valid. This study provides a basis for determining the appropriate thickness of geological media in lab-scale radon exhalation measurement experiments with open bottom.
Subject(s)
Radiation Monitoring , Radon , Soil Pollutants, Radioactive , Uranium , Diffusion , Exhalation , Radon/analysis , Soil Pollutants, Radioactive/analysisABSTRACT
Soybean-derived bio-oil is one of the vegetable-based oils that is gaining the most interest for potential use in the rejuvenation of aged asphalt binders. This laboratory study was conducted to characterize and quantify the diffusion and rheological properties of bio-oil-rejuvenated aged asphalt binder (BRAA) using soybean oil. In the study, the chemical structure of the soybean oil was comparatively characterized using an element analyzer (EA), gel permeation chromatography (GPC), and a Fourier infrared (FTIR) spectrometer, respectively. Based on the chemical structure of the bio-oil, BRAA molecular models were built for computing the diffusion parameters using molecular dynamic simulations. Likewise, a dynamic shear rheometer (DSR) test device was used for measuring and quantifying the rheological properties of the aged asphalt binder rejuvenated with 0%, 1%, 2%, 3%, 4%, and 5% soybean oil, respectively. The laboratory test results indicate that bio-oil could potentially improve the diffusion coefficients and phase angle of the aged asphalt binder. Similarly, the corresponding decrease in the complex shear modulus has a positive effect on the low-temperature properties of BRAA. For a bio-oil dosage 4.0%, the diffusion coefficients of the BRAA components are 1.52 × 10-8, 1.33 × 10-8, 3.47 × 10-8, 4.82 × 10-8 and 3.92 × 10-8, respectively. Similarly, the corresponding reduction in the complex shear modulus from 1.27 × 107 Pa to 4.0 × 105 Pa suggests an improvement in the low-temperature properties of BRAA. Overall, the study contributes to the literature on the potential use of soybean-derived bio-oil as a rejuvenator of aged asphalt binders.
Subject(s)
Hydrocarbons/chemistry , Molecular Dynamics Simulation , Petroleum/analysis , Plant Oils/chemistry , Polyphenols/chemistry , Rheology/methods , Soybean Oil/chemistry , Chromatography, Gel/methods , Cold Temperature , Diffusion , Hot Temperature , Molecular Structure , Spectroscopy, Fourier Transform Infrared/methods , ViscosityABSTRACT
Pectin grafted polyacrylic copolymer hydrogels were made by free radical crosslink copolymerization of acrylic acid (AA) and acrylamide (AM) in an aqueous solution of pectin. N'N-methylene bis acrylamide (MBA) was used as a crosslinker. During the polymerization reaction the attapulgite (APG) filler was also incorporated in situ into the network of the copolymer gel. Several filled hydrogels were prepared by varying the amount of pectin and APG filler. These hydrogels were characterized by FTIR, 13C NMR, XRD, TGA, SEM, mechanical properties, DMA, swelling, diffusion characteristics and network parameters. The release kinetics of a model drug diltiazem hydrochloride (DT) was studied with these hydrogels. The wt% of pectin, APG and MBA was optimized with a central composite design (CCD) model of response surface methodology (RSM) with equilibrium swelling ratio (ESR), drug adsorption (mg/100 mg gel) and drug release% in 16 h as response. Accordingly, the hydrogel prepared with 5:1 AA:AM molar ratio, 25 wt% monomer concentration, 1% each of initiator and MBA concentration, 18 wt% pectin and 2 wt% APG showed an optimized ESR of 17.75, drug loading of 27.58 and a drug release % of 92.5 in 16 h at a solution pH of 7.4.