Catalytic flash pyrolysis of Scenedesmus sp. post-extraction residue using low-cost HZSM-5 catalyst with the perspective to produce renewable aromatic hydrocarbons.

Recovering renewable chemicals from de-fatted microalgal residue derived from lipid extraction within the algal-derived biofuel sector is crucial, given the rising significance of microalgal-derived biodiesel as a potential substitute for petroleum-based liquid fuels. As a circular economy strategy, effective valorization of de-fatted biomass significantly improves the energetic and economic facets of establishing a sustainable algal-derived biofuel industry. In this scenario, this study investigates flash catalytic pyrolysis as a sustainable pathway for valorizing Scenedesmus sp. post-extraction residue (SPR), potentially yielding a bio-oil enriched with upgraded characteristics, especially renewable aromatic hydrocarbons. In the scope of this study, volatile products from catalytic and non-catalytic flash pyrolysis were characterized using a micro-furnace type temperature programmable pyrolyzer coupled with gas chromatographic separation and mass spectrometry detection (Py-GC/MS). Flash pyrolysis of SPR resulted in volatile products with elevated oxygen and nitrogen compounds with concentrations of 46.4% and 26.4%, respectively. In contrast, flash pyrolysis of lyophilized microalgal biomass resulted in lower concentrations of these compounds, with 40.9% oxygen and 17.3% nitrogen. Upgrading volatile pyrolysis products from SPR led to volatile products comprised of only hydrocarbons, while completely removing oxygen and nitrogen-containing compounds. This was achieved by utilizing a low-cost HZSM-5 catalyst within a catalytic bed at 500 °C. Catalytic experiments also indicate the potential conversion of SPR into a bio-oil rich in monocyclic aromatic hydrocarbons, primarily BETX, with toluene comprising over one-third of its composition, thus presenting a sustainable pathway for producing an aromatic hydrocarbon-rich bio-oil derived from SPR. Another significant finding was that 97.8% of the hydrocarbon fraction fell within the gasoline range (C5-C12), and 35.5% fell within the jet fuel range (C8-C16). Thus, flash catalytic pyrolysis of SPR exhibits significant promise for application in drop-in biofuel production, including green gasoline and bio-jet fuel, aligning with the principles of the circular economy, green chemistry, and bio-refinery.

The comprehensive effects of aluminum oxide nanoparticles on the physiology of freshwater microalga Scenedesmus obliquus and it's phycoremediation performance for the removal of sulfacetamide.

Nanoparticles are inevitable byproducts of modern industry. However, the environmental impacts arising from industrial applications of nanoparticles are largely under-reported. This study evaluated the ecotoxicological effects of aluminum oxide nanoparticles (Al2O3NP) and its influence on sulfacetamide (SA) biodegradation by a freshwater microalga, Scenedesmus obliquus. Although Al2O3NP showed limited toxicity effect on S. obliquus, we observed the toxicity attenuation aspect of Al2O3NP in a mixture of sulfacetamide on microalgae. The addition of 100 mg L-1 of Al2O3NP and 1 mg L-1 of SA reduced total chlorophyll by 23.3% and carotenoids by 21.6% in microalgal compared to control. The gene expression study demonstrated that ATPF0C, Lhcb1, HydA, and psbA genes responsible for ATP synthesis and the photosynthetic system were significantly downregulated, while the Tas gene, which plays a major role in biodegradation of organic xenobiotic chemicals, was significantly upregulated at 1 and 100 mg L-1 of Al2O3NP. The S. obliquus removed 16.8% of SA at 15 mg L-1 in 14 days. However, the removal was slightly enhanced (18.8%) at same concentration of SA in the presence of 50 mg L-1 Al2O3NP. This result proves the stability of sulfacetamide biodegradation capacity of S. obliquus in the presence of Al2O3NP co-contamination. The metabolic analysis showed that SA was degraded into simpler byproducts such as sulfacarbamide, sulfaguanidine, sulfanilamide, 4-(methyl sulfonyl)aniline, and N-hydroxy-benzenamine which have lower ecotoxicity than SA, demonstrating that the ecotoxicity of sulfacetamide has significantly decreased after the microalgal degradation, suggesting the environmental feasibility of microalgae-mediated wastewater technology. This study provides a deeper understanding of the impact of nanoparticles such as Al2O3NP on aquatic ecosystems.

Self-regulation mechanism difference of Chlorella vulgaris and Scenedesmus obliquus in toxic sludge extract caused by hydroquinone biodegradation.

Chlorella vulgaris (C. vulgaris) and Scenedesmus obliquus (S. obliquus) were compared to remove toxicity under conditions of sludge extract cultivation for 30 days. The toxicity of sludge extract, the growth characteristics, photosynthetic pigment, superoxide dismutase (SOD) enzyme and catalase (CAT) enzyme activities of the two microalgae were studied by contrast. The results showed that small molecular organic matter (<500 Da) was more easily utilized by microalgae. The toxicity in the toxic group of C. vulgaris and S. obliquus on the 30th day decreased to 56.8 ± 1.2% and 60.7 ± 2.8%, respectively. In the toxic group, the maximal SOD enzyme activity of C. vulgaris and S. obliquus were 2.02 U/mg proteins and 8.21 U/mg proteins, respectively, demonstrating that toxicity caused more oxidative damage to S. obliquus than to C. vulgaris. Proteomics analysis revealed that C. vulgaris mainly regulates energy synthesis and distribution primarily through sugar metabolism, and biomass synthesis primarily through carbon metabolism, whereas S. obliquus mainly regulates energy synthesis and distribution primarily through sugar metabolism and oxidative phosphorylation, resulting in sludge toxicity stress regulation.

Influence of Nitrogen to Phosphorus Ratio and CO2 Concentration on Lipids Accumulation of Scenedesmus dimorphus for Bioenergy Production and CO2 Biofixation.

The potential of Scenedesmus dimorphus microalgae for CO2 biofixation and lipid biosynthesis for bioenergy applications was evaluated in this study. Batch experiments were conducted using synthetic tertiary municipal wastewater samples at several nitrogen to phosphorus (NP) ratios (1 : 1 to 8 : 1) and CO2 concentrations (∼0%, 2%, 4%, and 6% CO2 in supplied air). Scenedesmus dimorphus was cultivated for 25 days and the growth is highly dependent on the CO2 concentration and the NP ratio. An NP ratio of 2 : 1 produces a biomass yield of 733 mg/L when the microalga culture was supplied with air enriched with 2% CO2 . The maximum CO2 biofixation rate of 49.6 mg L-1 d-1 is at an NP ratio of 8 : 1 with 4% CO2 . A colorimetric technique depending on sulpho-phospho-vanillin (SPV) was utilized for the determination of the intracellular lipid content. The highest lipid content of 31.6% as the dry weight of the biomass is at an NP ratio of 1 : 1 and 6% CO2 . These results indicate that supplementation of suitable CO2 with favorable NP ratio has a considerable effect on lipid accumulation in the microalgae Scenedesmus dimorphus biomass.

Removal of biogenic compounds from the post-fermentation effluent in a culture of Chlorella vulgaris.

Wastewater rich in organic carbon, nitrogen and phosphorus may serve as a convenient source of carbon and nutrients for a year-long microalgae production. Scientific reports indicate that some single-cell microalgae such as Chlorella and Scenedesmus, are highly tolerant to wastewater environments and efficiently remove biogenic compounds. The aim of this study was to determine the possibility of using the effluent produced in the process of anaerobic degradation of whey as a culture medium for the multiplication of Chlorella vulgaris algae biomass and to characterise their growth efficiency and rate. The content of nitrogen and phosphorus in wastewater was sufficient for conducting an effective culture of algae. The efficiency of nitrogen removal in the flow system was 15.61 ± 1.38 mg N/dm3/day.

Microwave-Assisted Biodiesel Production from Microalgae, Scenedesmus Species, Using Goat Bone-Made Nano-catalyst.

The production of biodiesel from Scenedesmus algal oil is one of the best alternative forms of liquid fuel production from biomass to petrol diesel. Biodiesel plays a significant role in the carbon sequestration process during cultivation. Scenedesmus algal species was isolated and cultured in a bold basal medium by using nonheat releasing white florescence (2500 lx) for a 12:12-h dark and light cycle. Algae oil was extracted from dried microalgae biomass through a microwave digester-assisted solvent extraction method. Consequently, about 20.8% algal oil per gram was obtained. A waste-based calcium oxide (CaO) nano-catalyst prepared from goat bone was used in the transesterification process. The catalyst was calcinated at 900 °C and characterized using FTIR, SEM, EDX, and XRD techniques. The results revealed a mean particle size of 43.96 nm with an irregular shape, porous structure, and possession of many active sites. The optimized transesterification process offers an optimum biodiesel yield of 92% at the experimental conditions, i.e., at a reaction temperature of 60 °C, 2% (Wt.) catalyst loading and 11:1 methanol to algal oil molar ratio, 1500 rpm stirring speed, and 3 h reaction duration. The physicochemical properties of the produced biodiesel were tested according to ASTM D6751 standards and are in good agreement.

Effect of cell disruption methods on the extraction of bioactive metabolites from microalgal biomass.

Microalgae synthesize a variety of potentially high-value compounds. Due to their robust cell wall, cell disruption is necessary to improve extraction of these compounds. While cell disruption methods have been optimized for lipid and protein extraction, there are limited studies for other bioactive compounds. The present study investigated the effect of freeze-drying combined with sonication or ball-milling on the extraction of antioxidant and plant biostimulating compounds from Chlorella sp., Chlorella vulgaris and Scenedesmus acutus. Both cell disruption methods resulted in higher extract yields from the biomass compared to freeze-dried biomass using 50% methanol as a solvent. Antioxidant activity of Chlorella extracts was generally higher than freeze-dried extracts based on the diphenylpicrylhydrazyl (DPPH) and ß-carotene linoleic acid assays. However, the effectiveness of each treatment varied between microalgae strains. Sonication resulted in the highest antioxidant activity in Chlorella sp. extracts. Ball-milling gave the best results for C. vulgaris extracts in the DPPH assay. Both cell disruption methods decreased antioxidant activity in S. acutus extracts. Plant biostimulating activity was tested using the mung bean rooting assay. Damaging the membrane by freeze-drying was sufficient to release the active compounds using water extracts. In contrast, both cell disruption methods negatively affected the biological activity of the extracts. These results indicate that bioactive compounds in microalgae are sensitive to post-harvest processes and their biological activity can be negatively affected by cell disruption methods. Care must be taken to not only optimize yield but to also preserve the biological activity of the target compounds.

Morphological characterization, growth appraisal, and probing biofuels potential of newly isolated Scenedesmus sp. from desert Cholistan.

Microalgae have an excellent potential for producing valuable natural products, including biofuels. Therefore, it is imperative to explore and document the existing microalgal flora and utilize their potentials to cope the increasing human needs. The present work aims at exploring and characterizing newly isolated microalgae from desert Cholistan, a habitat with myriad algal diversity. Light microscopy, scanning electron microscopy, and molecular phylogenetic approaches were used for species-level identification. Characterization and growth optimization of Scendesmus sp. were analyzed under three different growth modes to determine the most favorable conditions for increasing biomass, growth rate, and lipid content. The results revealed that mixotrophic (MT) mode significantly increases photosynthetic activity, growth rate, and lipid content with glycerol as supplement carbon source. The investigated Scenedesmus dimorphous produced a maximum dry weight of 1.73 g L-1 , improved fatty acid methyl esters profile and yield lipid up to 40% of DCW (68 g L-1 ) under MT mode, which is almost double to that of photoautotrophic cultivation. The glycerol availability in medium has been identified as the critical element for boosting growth and lipid content. Thus, it can reduce the cost of biofuel production.

The relationship between sulfur metabolism and tolerance of hexavalent chromium in Scenedesmus acutus (Spheropleales): Role of ATP sulfurylase.

Sulfur availability and the end products of its metabolism, cysteine, glutathione and phytochelatins, play an important role in heavy metal tolerance, chromium included. Sulfate and chromate not only compete for the transporters but also for assimilation enzymes and chromium tolerance in various organisms has been associated to differences in this pathway. We investigated the mechanisms of Cr(VI)-tolerance increase induced by S-starvation focusing on the role of ATP sulfurylase (ATS) in two strains of Scenedesmus acutus with different chromium sensitivity. S-starvation enhances the defence potential by increasing sulfate uptake/assimilation and decreasing chromium uptake, thus suggesting a change in the transport system. We isolated two isoforms of the enzyme, SaATS1 and SaATS2, with different sensitivity to sulfur availability, and analysed them in S-sufficient and S-replete condition both in standard and in chromium supplemented medium. SaATS2 expression is different in the two strains and presumably marks a different sulfur perception/exploitation in the Cr-tolerant. Its induction and silencing are compatible with a role in the transient tolerance increase induced by S-starvation. This enzyme can however hardly be responsible for the large cysteine production of the Cr-tolerant strain after starvation, suggesting that cytosolic rather than chloroplastic cysteine production is differently regulated in the two strains.

Evaluating the efficacy of an algae-based treatment to mitigate elicitation of antibiotic resistance.

Antibiotics in the effluents of municipal wastewater treatment plants (WWTP) may create selective pressures to induce antibiotic resistance in bacteria downstream. This study evaluates ciprofloxacin (CIP) removal by a freshwater alga, Scenedesmus dimorphus, to assess the efficacy of algae-based tertiary treatment in reducing effluent-induced CIP resistance. Results show significant CIP removal in light-exposed samples without algae and experimental algae (EA) samples: 53% and 93%, respectively, over 144 h. A residual antibiotic potency assay reveals that untreated CIP is significantly more growth-inhibiting to a model bacterium (Escherichia coli) than the algae-treated and light-exposed samples during short exposures (6 h). Adaptive laboratory evolution (ALE), again using E. coli, reveals that treated samples exhibit reduced capacity to elicit CIP resistance during sustained exposures compared to untreated CIP. Finally, observed CIP resistance in the CIP-exposed ALE lineages is corroborated via genotype characterization, which reveals the presence of resistance-associated mutations in gyrase subunit A (gyrA) that are not present in ALE lineages exposed to algae treated or light-exposed samples. As such, algae-mediated tertiary treatment could be effective in suppressing CIP resistance in bacterial communities downstream from WWTP. In addition, ALE is useful for assessing the potential of wastewater-relevant samples to elicit antibiotic resistance downstream.

Comparison of monoculture and mixed culture (Scenedesmus obliquus and wild algae) for C, N, and P removal and lipid production.

This study compared the efficiency of nutrient removal and lipid accumulation by a monoculture of Scenedesmus obliquus and mixed cultures of microalgae. The highest removal efficiencies of ammonium (99.2%), phosphate (91.2%), and total organic carbon (83.6%) occurred in the monoculture. All the mixed cultures were dominated by S. quadricauda; in some mixed cultures, the proportions of Chlamydomonas reinhardtii and C. microsphaera reached > 20%. The lipid content and lipid production in the monoculture were 15.9% and 52.3 mg kg-1, respectively, significantly higher than those in all the mixed cultures of microalgae. In all the mixed cultures, the proportion of palmitic acid was > 50%. The results suggest that the monoculture had advantages over the mixed culture of microalgae in terms of nutrient removal and lipid production.

Modulation of lipid content and lipid profile by supplementation of iron, zinc, and molybdenum in indigenous microalgae.

The effects of iron (Fe), zinc (Zn), and molybdenum (Mo) on the biomass yield, lipid content, lipid yield, and fatty acid composition of Chlorella sp. NC-MKM, Graesiella emersonii NC-M1, Scenedesmus acutus NC-M2, and Chlorophyta sp. NC-M5 were studied. Among them, G. emersonii NC-M1 recorded the highest percentage increase in lipid content (140.3%) and neutral lipid (50.9%) under Zn-supplemented condition compared to the control. Also, it showed a 105% and 41.88% increase in lipid yield and neutral lipid under Fe-supplemented condition compared to the control. However, Chlorella sp. NC-MKM recorded an elevation in lipid yield (70.3% rise) and neutral lipid (24.32% rise) compared to the control in Mo-supplemented condition. The enhanced production of reactive oxygen species (ROS) and antioxidant enzyme (SOD and POD) under Fe-, Zn-, and Mo-supplemented condition supports the lipid accumulation. FAME analysis showed that the overall percentage of SFA and MUFA increased after the addition of Fe, Zn, and Mo in a culture medium compared to the control which is vital for a good-quality biodiesel. Further, biodiesel properties derived from FAMEs such as CN, SV, IV, CFPP, OS, υ, ρ, and HHV were found in accordance with biodiesel standard.

Immobilized oleaginous microalgae as effective two-phase purify unit for biogas and anaerobic digester effluent coupling with lipid production.

Oleaginous microalga Scenedesmus sp. was immobilized in alginate-gel beads and applied as two-phase purify unit for biogas and anaerobic digester effluent from palm oil mill. Optimal microalgal cell concentration and bead volume ratio were 106 cells mL-1 and 25% v/v, respectively. The use of 20% effluent and light intensity at 128 µmol·proton·m-2 s-1 most promoted CO2 removal by immobilized microalgae and achieved the maximum CO2 removal rate of 4.63 kg-CO2 day-1 m-3. This process upgraded methane content in biogas (>95%) and completely remove nitrogen and phosphorus in the effluent. After process operation, 2.98 g L-1 microalgal biomass with 35.92% lipid content were recovered by simple sieving method. Microalgal lipids are composed of C16-C18 (>98%) with prospect high cetane number and short ignition delay time. This study has shown the promising biorefinery concept which is effective not only in CO2 fixation, biogas upgrading and pollutant removal but also cost-effective production of microalgae-based biofuel.

Hydrothermal liquefaction of Scenedesmus abundans biomass spent for sorption of petroleum residues from wastewater and studies on recycling of post hydrothermal liquefaction wastewater.

In this study Scenedesmus abundans was used as a biosorbent material for removing hydrocarbons from simulated petroleum wastewater. Batch experiments resulted in the removal of 92.16% of hydrocarbons from simulated wastewater within 60 min. The spent biosorbent was converted to bio-oil through hydrothermal liquefaction process (HTL) at temperature range from 220 to 320 °C with 1 h holding time. Liquid hydrocarbons (bio-oil) yield was 43.4 wt% at 300 °C with 15 g of spent sorbent loading and possessed HHV of 39.10 MJ/Kg. Additionally the HTL wastewater (aqueous phase) was recycled as reaction medium and studied for its effects on bio-oil yield which increased till second cycle (47.91 wt%). HTL bio-char was employed as adsorbent to remove heavy metals from wastewater. It showed greater removal efficiency of 86.5% to Ni(II) ions. From the results it was concluded that the petroleum residues can be effectively recycled back into liquid hydrocarbons with simple waste management pathway.

Transcriptome analysis for phosphorus starvation-induced lipid accumulation in Scenedesmus sp.

Phosphorus stress was applied to enhance the lipid production in Scenedesmus sp. The highest lipid production (350 mg L-1) and lipid content (approximately 41.0% of dry weight) were obtained by addition of 2 mg L-1 NaH2PO4·2H2O every 2 days, which were higher than those in replete phosphorus. Correspondingly, carbohydrate content decreased significantly. We speculated that phosphorus limitation could block starch biosynthesis, and photosynthate flow tended to fatty acid biosynthesis to cope with stress. To investigate the mechanism that phosphorus stress triggers the carbon fixation to lipid biosynthesis, the transcriptome analysis was carried out by the Illumina RNA-seq platform. A total of 2897 genes were identified as differentially expressed genes. The observed overexpression of lipid production under phosphorus stress was bolstered by up-regulation of genes encoding for DGAT and pyruvate kinase, activation of carbohydrate metabolism pathway and fatty acid biosynthesis, and repression of carbohydrate synthesis-presumably to shunt the carbon flux toward TAG biosynthesis. The transcriptome will be useful to understand the lipid metabolism pathway and obtain the engineering economic algae species aimed at biodiesel production.

Determining variables that influence the phosphorus content of waste stabilization pond algae.

Waste stabilization ponds (WSP) are one of the most common forms of wastewater treatment for smaller communities globally, but have poor phosphorus removal. It is known that WSP algae can accumulate polyphosphate within their cells in excess of that needed for cell function. If polyphosphate accumulation could be triggered at the higher range of WSP cell concentrations, phosphorus removal from domestic wastewater could be significantly improved. However, this phenomenon is sporadic and still not fully understood. With a view of building a fundamental understanding to underpin the engineering of a new phosphorus removal process, this paper examines eight previously untested variables that may influence the cellular phosphorus content of WSP biomass. Although calcium, magnesium, and potassium are key constituents of polyphosphate granules, the concentrations tested were not limiting to polyphosphate accumulation. While literature also pointed to inoculum characteristics as potentially having an impact, no significance was found in this research. Conversely, three important new triggers where identified that significantly (90% confidence) affected the cellular phosphorus content of WSP biomass. An increase in cellular phosphorus content was triggered by decreasing the organic load, or allowing the pH to increase as compared to pH control. By contrast, the presence of mixing decreased the phosphorus content of the WSP biomass.

Carbon-dioxide biofixation and phycoremediation of municipal wastewater using Chlorella vulgaris and Scenedesmus obliquus.

The pure cultures of microalgae Chlorella vulgaris ATCC 13482 and Scenedesmus obliquus FACHB 417 were grown in municipal wastewater in 7-L airlift bubble column photobioreactor supplied with 5% CO2/air (v/v). Batch experiments were conducted at 25 °C with 14-h light/10-h dark cycle for a period of 10 days. The CO2 capture efficiencies for both the microalgae were monitored in terms of their respective biomass productivities, carbon contents, and CO2 consumption rates. In the present study, the initial concentration of ammonia (43.7 mg L-1) was decreased to 2.9 and 3.7 mg L-1 by C. vulgaris and S. obliquus, respectively. And, the initial concentration of phosphate (18.5 mg L-1) was decreased to 1.1 and 1.6 mg L-1 by C. vulgaris and S. obliquus, respectively. CO2 biofixation rates by C. vulgaris and S. obliquus, cultivated in municipal wastewater, were calculated to be 140.91 and 129.82 mg L-1 day-1, respectively. The findings from the present study highlight the use of microalgae for wastewater treatment along with CO2 uptake and biomass utilization for pilot scale production of biodiesel, biogas, feed supplements for animals, etc., thus minimizing the production costs.

Improvement on lipid production by Scenedesmus obliquus triggered by low dose exposure to nanoparticles.

Carbon nanotubes (CNTs), α-Fe2O3 nanoparticles (nano Fe2O3) and MgO nanoparticles (nano MgO) were evaluated for the effects on algae growth and lipid production. Nano Fe2O3 promoted cell growth in the range of 0-20 mg·L-1. CNTs, nano Fe2O3 and nano MgO inhibited cell growth of Scenedesmus obliquus at 10, 40 and 0.8 mg·L-1 respectively. Neutral lipid and total lipid content increased with the increasing concentration of all tested nanoparticles. The maximum lipid productivity of cultures exposed to CNTs, nano Fe2O3 and nano MgO was observed at 5 mg·L-1, 5 mg·L-1 and 40 mg·L-1, with the improvement by 8.9%, 39.6% and 18.5%. High dose exposure to nanoparticles limited increase in lipid productivity, possibly due to the repression on cell growth caused by nanoparticles-catalyzed reactive oxygen species (ROS) generation, finally leading to reduction in biomass and lipid production. Reduced accumulation of fatty acids of C18:3n3, C18:3n6 and C20:2 was observed in cells exposed to nanoparticles.

Screening of microalgae for integral biogas slurry nutrient removal and biogas upgrading by different microalgae cultivation technology.

The microalgae-based technology has been developed to reduce biogas slurry nutrients and upgrade biogas simultaneously. In this work, five microalgal strains named Chlorella vulgaris, Scenedesmus obliquus, Selenastrum capricornutum, Nitzschia palea, and Anabaena spiroides under mono- and co-cultivation were used for biogas upgrading. Optimum biogas slurry nutrient reduction could be achieved by co-cultivating microalgae (Chlorella vulgaris, Scenedesmus obliquus, and Nitzschia palea) with fungi using the pelletization technology. In addition, the effects of different ratio of mixed LED light wavelengths applying mixed light-emitting diode during algae strains and fungi co-cultivation on CO2 and biogas slurry nutrient removal efficiency were also investigated. The results showed that the COD (chemical oxygen demand), TN (total nitrogen), and TP (total phosphorus) removal efficiency were 85.82 ± 5.37%, 83.31 ± 4.72%, and 84.26 ± 5.58%, respectively at red: blue = 5:5 under the co-cultivation of S. obliquus and fungi. In terms of biogas upgrading, CH4 contents were higher than 90% (v/v) for all strains, except the co-cultivation with S. obliquus and fungi at red: blue = 3:7. The results indicated that co-cultivation of microalgae with fungi under mixed light wavelengths treatments was most successful in nutrient removal from wastewater and biogas upgrading.

Selective degradation of the recalcitrant cell wall of Scenedesmus quadricauda CASA CC202.

MAIN CONCLUSION: An eco-friendly cell wall digestion strategy was developed to enhance the availability of nutritionally important bio molecules of edible microalgae and exploit them for cloning, transformation, and expression of therapeutic proteins. Microalgae are the source for many nutritionally important bioactive compounds and potential drugs. Even though edible microalgae are rich in nutraceutical, bioavailability of all these molecules is very less due to their rigid recalcitrant cell wall. For example, the cell wall of Scenedesmus quadricauda CASA CC202 is made up of three layers comprising of rigid outer pectin and inner cellulosic layer separated by a thin middle layer. In the present investigation, a comprehensive method has been developed for the selective degradation of S. quadricauda CASA CC202 cell wall, by employing both mechanical and enzymatic treatments. The efficiency of cell wall removal was evaluated by measuring total reducing sugar (TRS), tannic acid-ferric chloride staining, calcoflour white staining, scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR) analysis. It was confirmed that the yield of TRS increased from 129.82 mg/g in 14 h from pectinase treatment alone to 352.44 mg/g by combined sonication and enzymatic treatment within 12 h. As a result, the combination method was found to be effective for the selective degradation of S. quadricauda CASA CC202 cell wall. This study will form a base for our future works, where this will help to enhance the digestibility and availability of nutraceutically important proteins.