RESUMEN
Microbial contamination in aircraft fuel-containing systems poses significant threats to flight safety and operational integrity as a result of microbiologically influenced corrosion (MIC). Regular monitoring for microbial contamination in these fuel systems is essential for mitigating MIC risks. However, the frequency of monitoring remains a challenge due to the complex environmental conditions encountered in fuel systems. To investigate the impact of environmental variables such as water content, oxygen levels, and temperature on the MIC of aluminum alloy in aircraft fuel systems, orthogonal experiments with various combinations of these variables were conducted in the presence of sulfate-reducing bacteria. Among these variables, water content in the fuel oil demonstrated the most substantial influence on the corrosion rate of aluminum alloys, surpassing the effects of oxygen and temperature. Notably, the corrosion rate of aluminum alloys was the highest in an environment characterized by a 1:1 water/oil ratio, 0% oxygen, and a temperature of 35 °C. Within this challenging environment, conducive to accelerated corrosion, changes in the corrosion behavior of aluminum alloys over time were analyzed to identify the time point at which MIC intensified. Observations revealed a marked increase in the depth and width of corrosion pits, as well as in the corrosion weight-loss rate, starting from the 7th day. These findings offer valuable insights for determining the optimal frequency of microbial contamination detection in aircraft fuel systems.
RESUMEN
Metal materials undergo severe corrosion in eutrophic environments. The effect of DO decay stimulated by high concentrations of nitrogen and phosphorus pollutants on microorganisms leads to the coupling of electrochemical and microbial corrosion processes. However, there are few studies on microbial corrosion mechanisms in eutrophic environments. This article discusses the corrosive factors of marine eutrophication, summarizes the impact of marine eutrophication on microbial corrosion and the potential mechanisms, including aerobic biofilm corrosion, aerobic & anaerobic mixed biofilm corrosion, and anaerobic microbial electron transfer corrosion, and expounds on the research methods for microbial corrosion of materials serving in estuarine areas prone to pollution. Microbial prevention and control, such as nutrient restriction and microbial interspecies competition, are of research value in the field of green protection. Microbial corrosion mechanisms studies in marine eutrophication environments are significant for environment monitor development, water intake and algae control technologies, and corrosion protection in polluted environments.
Asunto(s)
Biopelículas , Eutrofización , Corrosión , Agua de Mar/química , Agua de Mar/microbiologíaRESUMEN
Biosynthetic metal sulfides showed great application prospects in the environmental treatment against high-valence metal pollutants. However, the efficiency of biosynthesis, agglomeration during the reaction process, and the formation of the passivation layer during the reduction process were always the important factors restricting its development. This study explored the composition of the culture medium to promote the growth of highly corrosive sulfate-reducing bacteria (SRB) and its metabolism to produce FeS nanoparticles (NPs). The results showed that reducing the carbon source (CS) and adding electron carriers in the culture medium effectively promoted the production of small, dispersed, and loose FeS NPs in cells. At pH = 7, 24 °C and 10 min reaction time, 0.1 g/L FeS NPs produced by SRB under the conditions of 10 % CS with 10 ppm cytochrome c medium could achieve 100 % removal efficiency of 1 mM hexavalent chromium (Cr(VI)). Under this condition, FeS NPs could be produced by intracellular metabolism in SRB cells, and environmental factors such as pH, metal cations, and Cl- had little effect on the removal of Cr(VI) by this FeS NPs. The surface proteins of FeS NPs significantly enhanced their antioxidant properties. After 7 days of natural environment exposure, the Cr(VI) removal efficiency of FeS NPs was only reduced by 16 % compared with the initial sample. This work provided an in-depth understanding of Cr(VI) removal by SRB biosynthesis of FeS and contributes to the widespread application of FeS in the future.
Asunto(s)
Carbono , Cromo , Cromo/metabolismo , Cromo/química , Carbono/química , Carbono/metabolismo , Desulfovibrio/metabolismo , Compuestos Ferrosos/metabolismo , Compuestos Ferrosos/química , Electrones , Propiedades de Superficie , Tamaño de la Partícula , Concentración de Iones de HidrógenoRESUMEN
Due to the development and utilization of nuclear energy, the safe disposal of nuclear waste needs to be urgently addressed. In recent years, the utilization of microorganisms' adsorption capacity to dispose of radioactive waste has received increasing attention. When compared with conventional disposal methods, microbial adsorption exhibits the characteristics of high efficiency, low cost, and no secondary pollution. In the long term, microbial biomass shows significant promise as specific chemical-binding agents. Optimization of biosorption conditions, identification of rare earth element binding sites, and studies on the sorption capacities of immobilized cells provide compelling reasons to consider biosorption for industrial applications in heavy metal removal from solutions. However, the interaction mechanism between microorganisms and radioactive nuclides is very complex. This mini-review briefly provides an overview of the preparation methods, factors affecting the adsorption capacity, and the mechanisms of microbial adsorbents.
RESUMEN
The monitoring of heavy metal ions in ocean is crucial for environment protection and assessment of seawater quality. However, the detection of heavy metal ions in seawater with electrochemical sensors, especially for long-term monitoring, always faces challenges due to marine biofouling caused by the nonspecific adsorption of microbial and biomolecules. Herein, an electrochemical aptasensor, integrating both antifouling and antibacterial properties, was developed for the detection of Hg2+ in the ocean. In this electrochemical aptasensor, eco-friendly peptides with superior hydrophilicity served as anti-biofouling materials, preventing nonspecific adsorption on the sensing interface, while silver nanoparticles were employed to eliminate bacteria. Subsequently, a ferrocene-modified aptamer was employed for the specific recognition of Hg2+, leveraging the aptamer's ability to fold into a thymine-Hg2+-thymine (T-Hg2+-T) structure upon interaction, and bringing ferrocene nearer to the sensor surface, significantly amplifying the electrochemical response. The prepared electrochemical aptasensor significantly reduced the nonspecific adsorption in seawater while maintaining sensitive electrochemical response. Furthermore, the biosensor exhibited a linear response range of 0.01-100 nM with a detection limit of 2.30 pM, and realized the accurate monitoring of mercury ions in real marine environment. The research results offer new insights into the preparation of marine antifouling sensing devices, and it is expected that sensors with antifouling and antimicrobial capabilities will find broad applications in the monitoring of marine pollutants.
Asunto(s)
Antibacterianos , Incrustaciones Biológicas , Técnicas Biosensibles , Técnicas Electroquímicas , Mercurio , Agua de Mar , Mercurio/análisis , Agua de Mar/química , Agua de Mar/microbiología , Técnicas Electroquímicas/métodos , Antibacterianos/análisis , Antibacterianos/farmacología , Técnicas Biosensibles/métodos , Incrustaciones Biológicas/prevención & control , Aptámeros de Nucleótidos/química , Plata/química , Contaminantes Químicos del Agua/análisis , Nanopartículas del Metal/química , Límite de Detección , Compuestos Ferrosos/química , MetalocenosRESUMEN
In this paper, a novel method was proposed for the synthesis of Cu2S on copper mesh via electrolysis in SRB culture medium. It was found that following electrolysis in SRB medium, squamous-like Cu2S arrays were obtained on the copper mesh, and the Cu2S loading contents varied with the electrolyzing parameters. The resultant Cu2S on copper mesh in SRB (CSCM-SRB) with the highest catalytic MB degradation properties was produced by electrolysis at 3.75 mA/cm2 for 900 s. The optimized MB-degrading conditions were determined to be 1.2 cm2/mL CSCM-SRB with 0.05 M H2O2 at 35 °C when pH = 6, under which the degradation of MB reached over 99% after 120 min of reaction. Disinfecting properties was also proven by antibacterial tests, revealing that an almost 100% antibacterial rate against E. coli was obtained after 8 min. The organic compounds produced by SRB adsorbed on CSCM-SRB strongly promoted the degradation of MB. Furthermore, possible Fenton-like mechanisms of CSCM-SRB were proposed, illustrating that ·O2-, ·OH, and 1O2 acted as the main functional species during Fenton-like reactions, leading to effective MB degradation and high antibacterial properties. Finally, a simple device for wastewater treatment was designed, providing possible applications in real environments.
RESUMEN
It has been a challenge to prepared polyether block amide (PEBA) fibrous membrane via solution electrospinning. The only few reported methods though involved hazardous solvents and surfactants which were against the principle of green chemistry. In this work, uniform fibrous membrane of PEBA was successfully fabricated by solution electrospinning with a bio-based solvent dihydrolevoglucosenone (Cyrene). To further improve the mechanical strength and adsorption performance of the PEBA membrane, a hierarchical magnesium hydrogen phosphate (MgHPO4·1.2H2O, MHP) was synthesized to blend evenly into the PEBA matrix. A Janus MHP/PEBA membrane with one side of hydrophobic surface and the other side of hydrophilic surface was subsequently prepared, which exhibited fast adsorption, high capacity, good selectivity and reusability towards ibuprofen, acetaminophen, carbamazepine and triclosan. In addition, the Janus membrane showed high removal efficiency of the above contaminants in secondary wastewater effluent with good long term stability. It demonstrated that this Janus MHP/PEBA membrane had a good potential in practical wastewater treatment.
Asunto(s)
Membranas Artificiales , Tecnología Química Verde , Adsorción , Contaminantes Químicos del Agua/aislamiento & purificación , Contaminantes Químicos del Agua/química , Fosfatos/química , Fosfatos/aislamiento & purificación , Polímeros/química , Propiedades de Superficie , Preparaciones Farmacéuticas/química , Preparaciones Farmacéuticas/aislamiento & purificación , Amidas/química , Amidas/aislamiento & purificación , Tamaño de la Partícula , Purificación del Agua/métodos , Cosméticos/química , Cosméticos/aislamiento & purificaciónRESUMEN
Microbiologically influenced corrosion (MIC) is a complicated process that happens ubiquitously and quietly in many fields. As a useful nutritional ingredient in microbial culture media, yeast extract (YE) is a routinely added in the MIC field. However, how the YE participated in MIC is not fully clarified. In the present work, the effect of YE on the growth of sulfate reducing prokaryotes (SRP) Desulfovibrio bizertensis SY-1 and corrosion behavior of X70 pipeline steel were studied. It was found that the weight loss of steel coupons in sterile media was doubled when YE was removed from culture media. However, in the SRP assays without YE the number of planktonic cells decreased, but the attachment of bacteria on steel surfaces was enhanced significantly. Besides, the corrosion rate of steel in SRP assays increased fourfold after removing YE from culture media. MIC was not determined for assays with planktonic SRP but only for biofilm assays. The results confirm the effect of YE on D. bizertensis SY-1 growth and also the inhibitory role of YE on MIC.
Asunto(s)
Desulfovibrio , Acero , Corrosión , Biopelículas , Sulfatos , Plancton/microbiología , Medios de CultivoRESUMEN
Photocatalytic MoS2 with visible light response is considered as a promising bactericidal material owing to its non-toxicity and high antibacterial efficiency. However, photocatalysts always exist as powder, so it is difficult to settle photocatalysts on the metal surface, which limits their application in aqueous environments. To solve this problem, ultrasound and sodium dodecyl sulfate (SDS) were introduced into the co-deposition process of MoS2 and zinc matrix, so that novel MoS2-Zn coatings were obtained. In this process, ultrasound and SDS strongly promoted the dispersion and adsorption of MoS2 on the co-depositing surfaces. Then MoS2 were proved to be composited into the Zn matrix with effective structures, and the addition of SDS effectively increased the loading content of MoS2 in the MoS2-Zn coatings. Besides, the antibacterial performance of the MoS2-Zn coatings was evaluated with three typical fouling bacteria E.coli, S.aureus and B.wiedmannii. The MoS2-Zn coating showed high and broad-spectrum antibacterial properties with over 98 % inhibition rate against these three bacteria. Furthermore, it is proved that the MoS2-Zn coatings generated superoxide (·O2-) and hydroxyl radicals (·OH) under visible light, which played the dominant and subordinate roles in the antibacterial process, respectively. The MoS2-Zn coatings also showed high antibacterial stability after four "light-dark" cycles. According to the results of the attached bacteria, the MoS2-Zn coatings were considered to effectively repel the living pelagic bacteria instead of killing the attached ones, which was highly environmentally friendly. The obtained MoS2-Zn coatings were considered promising in biofilm inhibiting and marine antifouling fields.
Asunto(s)
Galvanoplastia , Molibdeno , Dodecil Sulfato de Sodio/química , Molibdeno/farmacología , Molibdeno/química , Antibacterianos/farmacología , Antibacterianos/química , Zinc/química , Escherichia coliRESUMEN
In this study, a novel Cu-based (Cu55Al20Ni12Ti8Si5, at.%) medium-entropy alloy (MEA) coating was prepared by high-velocity oxygen-fuel (HVOF) spraying technology. Thermo-Calc was employed to simulate the phase diagram of the alloy system. Phase composition and microstructure of the as-sprayed coating were characterized by means of XRD, FESEM, TEM and STEM/EDX. The effect of sulfate-reducing bacteria (SRB) on the corrosion behavior of the coating and the as-cast Ni-Al bronze (NAB) was investigated using electrochemical measurements and surface characterization. The Thermo-Cala simulation results showed that the alloy system presented a single BCC solid solution phase, while the detailed characterization of microstructure indicated that a few NiTi-rich B2-ordered precipitates could be also found in the as-sprayed coating other than the Cu-rich BCC matrix. Electrochemical studies illustrated that the coating exhibited superior corrosion resistance than the NAB in SRB medium, the corrosion acceleration efficiency induced by SRB of the NAB (95.3 %) was more severe than that of the coating (63.8 %). Surface analysis results demonstrated the occurrence of pitting corrosion and the formation of Cu2S on the coating surface after corroded in SRB medium. Corrosive metabolite HS- induced microbiologically influenced corrosion was considered as the main corrosion acceleration mechanism caused by SRB.
Asunto(s)
Aleaciones , Desulfovibrio , Aleaciones/química , Corrosión , Entropía , Oxígeno , Cobre/químicaRESUMEN
A large amount of nuclear waste produced in the process of nuclear energy utilization has always been a key problem to be solved urgently for nuclear safety. At present, "deep geological disposal" is a feasible method and generally accepted by many countries. The oxygen content in the near field environment of the waste container will decrease to anaerobic conditions, and hydrogen will permeation into the internal materials of container for a long time. Hydrogen evolution corrosion may cause a risk of hydrogen embrittlement. The harm of hydrogen embrittlement in metal container is far more severe than predictable uniform corrosion. It is a research hotspot that the microorganisms impact on the corrosion behavior of container materials in the deep geological environment. Microbial corrosion in deep geological environments can be divided into two types: aerobic microbial corrosion and anaerobic microbial corrosion. There is a type of hydrogen consuming microorganism in the natural environment that uses the oxidation of hydrogen as the energy for its life activities. This provides a new approach for us to study reducing the hydrogen embrittlement sensitivity of nuclear waste container materials.
RESUMEN
A microbiologically influenced corrosion (MIC) causes huge economic losses and serious environmental damage every year. The prevention and control measures for MIC mainly include physical, chemical, and biological methods. Among them, biocide application is the most cost-effective method. Although various biocides have their own advantages in preventing and treating MIC, most biocides have the problem of polluting the environment and increasing microorganism resistance. Therefore, it has stimulated the exploration of continuously developing new environmentally friendly and efficient biocides. In this review, the application advantages and research progress of various biocides used to prevent and control MIC are discussed. Also, this review provides a resource for the research and rational use of biocides regarding MIC mitigation and prevention.
RESUMEN
Electrochemical oxygen reduction reaction (ORR) is an attractive and alternative route for the on-site production of hydrogen peroxide (H2 O2 ). The electrochemical synthesis of H2 O2 in neutral electrolyte is in early studying stage and promising in ocean-energy application. Herein, N-doped carbon materials (N-Cx ) with different N types are prepared through the pyrolysis of zeolitic imidazolate frameworks. The N-Cx catalysts, especially N-C800 , exhibit an attracting 2e- ORR catalytic activity, corresponding to a high H2 O2 selectivity (≈95%) and preferable stability in 0.5 m NaCl solution. Additionally, the N-C800 possesses an attractive H2 O2 production amount up to 631.2 mmol g-1 h-1 and high Faraday efficiency (79.8%) in H-type cell. The remarkable 2e- ORR electrocatalytic performance of N-Cx catalysts is associated with the N species and N content in the materials. Density functional theory calculations suggest carbon atoms adjacent to graphitic N are the main catalytic sites and exhibit a smaller activation energy, which are more responsible than those in pyridinic N and pyrrolic N doped carbon materials. Furthermore, the N-C800 catalyst demonstrates an effective antibacterial performance for marine bacteria in simulated seawater. This work provides a new insight for electro-generation of H2 O2 in neutral electrolyte and triggers a great promise in ocean-energy application.
RESUMEN
Deterioration corrosion occurs between the external surface of oil pipelines and aerobic oil-degrading microorganisms in oil fields. Microorganisms with aerobic oil pollution remediation capabilities may catalyze more serious anaerobic microbial corrosion due to the carbon source supply. In this study, Acinetobacter soli strains were isolated from oil-contaminated environments, and their role in the deterioration corrosion behavior of X70 steel in an oil-water environment was investigated using the EDS multipoint scanning method. The presence of oil controls the deposition of carbon and phosphorus and diffusion of oxygen, leading to significant adhesion attraction and initial growth inhibition of biofilm on the metal surface. A. soli facilitates oxygen transfer and iron ion dissolution, thereby accelerating the pitting corrosion of X70 steel. This corrosion of the X70 steel, in turn, further accelerates the microbial degradation of oil, inhibiting the appearance of calcareous scale in the later stage of corrosion. The corrosion of X70 steel is influenced by microbial degradation, and the specific corrosion behaviors are related to the activity of A. soli in the petroleum environment. This study sheds light on the corrosion mechanisms of X70 steel by A. soli at different stages, providing insights into the interactions between microorganisms, oil pollution, and metal corrosion in oil fields.
Asunto(s)
Biopelículas , Acero , Corrosión , Carbono , AguaRESUMEN
Sulfate-reducing bacteria (SRB) are an important group of microorganisms that cause microbial corrosion. In this study, culturable SRB were isolated and identified from the inner rust layer of three kinds of steel and from sediments, and a comparison of amino acid sequences encoding related enzymes in the sulfate reduction pathway between anaerobic and facultative anaerobic SRB strains was carried out. The main results are as follows. (1) Seventy-seven strains were isolated, belonging to five genera and seven species, with the majority being Desulfovibrio marinisediminis. For the first time, Holodesulfovibrio spirochaetisodalis and Acinetobacter bereziniae were separated from the inner rust layer of metal, and sulfate reduction by A. bereziniae, Virgibacillus dokdonensis, and Virgibacillus chiguensis, etc., was also demonstrated for the first time. (2) Three strains of strictly anaerobic bacteria and four strains of facultative anaerobic bacteria were screened from seven bacterial strains. (3) Most of the anaerobic SRB only contained enzymes for the dissimilatory sulfate reduction pathway, while those of facultative anaerobic bacteria capable of producing hydrogen sulfide included two possible ways: containing the related enzymes from the dissimilatory pathway only, or containing enzymes from both dissimilatory and assimilation pathways. This study newly discovered that some bacterial genera exhibit sulfate reduction ability and found that there are differences in the distribution of enzymes related to the sulfate reduction pathway between anaerobic and facultative anaerobic SRB type trains, providing a basis for the development and utilization of sulfate-reducing bacterial resources and furthering our understanding of the metabolic mechanisms of SRB.
RESUMEN
Coaxial electrospun coatings with antibacterial and anticorrosion properties have a marked potential to protect against corrosion in marine environments. Ethyl cellulose is a promising biopolymer for corrosion caused by microorganisms owing to its high mechanical strength, nontoxicity, and biodegradability. In this study, a coaxial electrospun coating loaded with antibacterial carvacrol (CV) in the core and anticorrosion pullulan (Pu) and ethyl cellulose (EC) as a shell layer was successfully fabricated. The formation of core-shell structure was confirmed using transmission electron microscopy. Pu-EC@CV coaxial nanofiber had small diameters, uniform distribution, smooth surface, strong hydrophobicity, and no fractures. Electrochemical impedance spectroscopy was used to analyze corrosion of the electrospun coating surface in a medium containing bacterial solution. The results indicated significant corrosion resistance of the coating surface. In addition, the antibacterial activity and mechanism of coaxial electrospun were studied. The Pu-EC@CV nanofiber coating exhibited excellent antibacterial properties by effectively increasing the permeability of cell membranes and killing bacteria, as determined by plate counts, scanning electron microscopy, cell membrane permeability, and the activity of alkaline phosphatase. In summary, the coaxial electrospun pullulan-ethyl cellulose embedded with CV coating can be used as antibacterial and anticorrosion materials and may have potential applications in the field of marine corrosion.
Asunto(s)
Nanofibras , Corrosión , Antibacterianos/farmacologíaRESUMEN
In this paper, high-throughput sequencing technology was adopted to visualize the microbial communities on the surfaces of two types of carbon steel immersed in Sea Area â . The results showed that different microbial communities were formed on different carbon steel surfaces, in which the genus with the highest abundance on the surface of Q235 was Escherichia-Shigella, while anaerobic Desulfovibrio on the surface of 921a was the most abundant, and the dominant genus varied with the depth of the rust layer. In addition, the distribution of sulfate-reducing bacteria (SRB) on the surface of Q235 submerged in Sea Area â ¡ was compared with the sulfate-reducing bacteria's distribution in Sea Area â , using the environmental factors correlation analysis. The results showed that the concentrations of Ca2+, Na+, K+, Mg2+, and Al3+ were positively correlated with the distribution of SRB, while the concentrations of Cu2+, Zn2+, SO4 2-, Cl-, NO3 -, and organic carbon were negatively correlated with it. Furthermore, there was a highly significant correlation between each geochemical factor and Desulfotomaculum (p < 0.01).
Asunto(s)
Cáusticos , Microbiota , Acero , Agua de Mar/microbiología , Sulfatos , CarbonoRESUMEN
The sensitive and rapid detection of dopamine (DA) is of great significance for early diagnosis of related diseases. Current detection strategies of DA are time-consuming, expensive and inaccurate, while biosynthetic nanomaterials were considered highly stable and environment friendly, which were promising on colorimetric sensing. Thus, in this study, novel zinc phosphate hydrate nanosheets (SA@ZnPNS) biosynthesized by Shewanella algae were designed for the detection of DA. SA@ZnPNS showed high peroxidase-like activity which catalyzed the oxidation reaction of 3,3',5,5'-tetramethylbenzidine in the presence of H2O2. Results showed that the catalytic reaction of SA@ZnPNS followed Michaelis-Menton kinetics, and catalytic process conformed to ping-pong mechanism with chief active species of hydroxyl radicals. The colorimetric detection of DA in human serum samples was performed based on SA@ZnPNS peroxidase-like activity. The linear range of DA detection was 0.1-40 µM, and the detection limit was 0.083 µM. This study provided a simple and practical method for the detection of DA and expanded the application of biosynthesized nanoparticles to biosensing fields.
Asunto(s)
Materiales Biomiméticos , Peroxidasa , Humanos , Dopamina , Peróxido de Hidrógeno , Peroxidasas , Fosfatos , Colorimetría/métodos , Límite de DetecciónRESUMEN
Exploring new and high efficiency mimic enzymes is a vital and novel strategy for antibacterial application. Haloperoxidase-like enzymes have attracted wide attention thanks to their amazing catalytic property for hypohalous acid generation from hydrogen peroxide and halides. However, few materials have displayed halogenating catalytic performance until now. Herein, we synthesized N-doped C/CeO2 (N-C/CeO2) composite materials by a combination of the liquid and solid-state method. N-C/CeO2 can possess haloperoxidase-like catalytic activity by catalyzing the bromination of organic signaling compounds (phenol red) with H2O2 at a wide range of temperatures (20 °C to 55 °C), with a solution color changing from yellow to blue. Meanwhile, it exhibits high catalytic stability/recyclability in the catalytic reaction. The synthesized N-C/CeO2 composite can effectively catalyze the oxidation of Br- with H2O2 to produce HBrO without the presence of phenol red. The produced HBrO can resist typical marine bacteria like Pseudomonas aeruginosa. This study provides an efficient biomimetic haloperoxidase and a novel sustainable method for antibacterial application.