Effects of the Space Holder Shape on the Pore Structure and Mechanical Properties of Porous Cu with a Wide Porosity Range.

Porous copper (Cu), with varying porosities, has been made using carbamide as a space holder through the powder metallurgy route. Two shapes of carbamide particles were used, (i) needlelike and (ii) spherical, in order to investigate the effect of the space holder shape on the pore structure and mechanical properties of porous Cu. The compressive deformation behavior of porous Cu was studied under a compression test. The pores' structural characteristics and mechanical properties of the porous Cu varied significantly with the shape of the space holder. Although the effect of the space holder shape on the porosity was not regular, the effect on the mechanical properties was regular. The stress increased monotonically with the increase in the strain, and strain hardening occurred at the plastic yield stage. The elastic modulus and yield strength followed the power law, with the relative density irrespective of the space holder shape. The empirical constants associated with different empirically developed power law relations were different, according to the shape of space holder. A quantitative relationship between the elastic modulus and yield strength and the spacer content was obtained to control the mechanical properties of the present porous Cu or other porous metals and metal foams using the well-known space holder method.

Development of "Intelligent particles" for the treatment of dental caries.

Dental caries is one of the most prevalent non-communicable diseases worldwide, mediated by a multispecies biofilm that consists of high levels of acidogenic bacteria which ferment sugar to acid and cause teeth demineralization. Current treatment practice remains insufficient in addressing 1) rapid clearance of therapeutic agents from the oral environment 2) destroying bacteria that contribute to the healthy oral microbiome. In addition, increasing concerns over antibiotic resistance calls for innovative alternatives. In this study, we developed a pH responsive nano-carrier for delivery of polycationic silver nanoparticles. Branched-PEI capped silver nanoparticles (BPEI-AgNPs) were encapsulated in a tannic acid - Fe (III) complex-modified poly(D,L-lactic-co-glycolic acid) (PLGA) particle (Fe(III)-TA/PLGA@BPEI-AgNPs) to enhance binding to the plaque biofilm and demonstrate "intelligence" by releasing BPEI-AgNPs under acidic conditions that promote dental caries The constructed Fe(III)-TA/PLGA@BPEI-AgNPs (intelligent particles - IPs) exhibited significant binding to an axenic S. mutans biofilm grown on hydroxyapatite. Ag+ ions were released faster from the IPs at pH 4.0 (cariogenic pH) compared to pH 7.4. The antibiofilm results indicated that IPs can significantly reduce S. mutans biofilm volume and viability under acidic conditions. Cytotoxicity on differentiated Caco-2 cells and human gingival fibroblasts indicated that IPs were not cytotoxic. These findings demonstrate great potential of IPs in the treatment of dental caries.

Modelling the controlled drug release of push-pull osmotic pump tablets using DEM.

The push-pull osmotic pump tablet is a promising drug delivery approach, offering advantages over traditional dosage forms in achieving consistent and predictable drug release rates. In the current study, the drug release process of push-pull osmotic pump tablets is modelled for the first time using the discrete element method (DEM) incorporated with a microscopic diffusion-induced swelling model. The effects of dosage and formulation design, such as delivery orifice size, drug-to-polymer ratio, tablet surface curvature, friction between particles and cohesion of polymer particles, on the drug release performance are systematically analysed. Numerical results reveal that an enlarged delivery orifice significantly increases both the total drug release and the drug release rate. Moreover, the larger the swellable particle component in the tablet, the higher the drug release rate. Furthermore, the tablet surface curvature is found to affect the drug release profile, i.e. the final drug release percentage increases with the increasing tablet surface curvature. It is also found that the drug release rate could be controlled by adjusting the inter-particle friction and the cohesion of polymer particles in the formulation. This DEM study offers valuable insights into the mechanisms governing drug release in push-pull osmotic pump tablets.

An ultrasound-based ensemble machine learning model for the preoperative classification of pleomorphic adenoma and Warthin tumor in the parotid gland.

OBJECTIVES: The preoperative classification of pleomorphic adenomas (PMA) and Warthin tumors (WT) in the parotid gland plays an essential role in determining therapeutic strategies. This study aims to develop and validate an ultrasound-based ensemble machine learning (USEML) model, employing nonradiative and noninvasive features to differentiate PMA from WT. METHODS: A total of 203 patients with histologically confirmed PMA or WT who underwent parotidectomy from two centers were enrolled. Clinical factors, ultrasound (US) features, and radiomic features were extracted to develop three types of machine learning model: clinical models, US models, and USEML models. The diagnostic performance of the USEML model, as well as that of physicians based on experience, was evaluated and validated using receiver operating characteristic (ROC) curves in internal and external validation cohorts. DeLong's test was used for comparisons of AUCs. SHAP values were also utilized to explain the classification model. RESULTS: The USEML model achieved the highest AUC of 0.891 (95% CI, 0.774-0.961), surpassing the AUCs of both the US (0.847; 95% CI, 0.720-0.932) and clinical (0.814; 95% CI, 0.682-0.908) models. The USEML model also outperformed physicians in both internal and external validation datasets (both p < 0.05). The sensitivity, specificity, negative predictive value, and positive predictive value of the USEML model and physician experience were 89.3%/75.0%, 87.5%/54.2%, 87.5%/65.6%, and 89.3%/65.0%, respectively. CONCLUSIONS: The USEML model, incorporating clinical factors, ultrasound factors, and radiomic features, demonstrated efficient performance in distinguishing PMA from WT in the parotid gland. CLINICAL RELEVANCE STATEMENT: This study developed a machine learning model for preoperative diagnosis of pleomorphic adenoma and Warthin tumor in the parotid gland based on clinical, ultrasound, and radiomic features. Furthermore, it outperformed physicians in an external validation dataset, indicating its potential for clinical application. KEY POINTS: • Differentiating pleomorphic adenoma (PMA) and Warthin tumor (WT) affects management decisions and is currently done by invasive biopsy. • Integration of US-radiomic, clinical, and ultrasound findings in a machine learning model results in improved diagnostic accuracy. • The ultrasound-based ensemble machine learning (USEML) model consistently outperforms physicians, suggesting its potential applicability in clinical settings.

Subcutaneous injection of hyaluronic acid leading to emboliom and recanalization process monitored in real time by three-dimensional photoacoustic imaging.

This study describes a method for real-time examination of the microvascular system based on the three-dimensional photoacoustic imaging system to prevent arterial complications, especially vascular embolism, during hyaluronic acid (HA) injections. Chicken embryos were used to simulate the superficial blood vessels of human skin, and then the target area was imaged by the photoacoustic imaging system for three-dimensional vascular imaging, and then the syringe and blood vessels were monitored, and the syringe angle and penetration depth were adjusted in time using an injection device to avoid puncturing the arterial vasculature and clogging the blood vessels. HA was then injected into smaller vessels on the dorsum of the tongue in mice and into thicker vessels on the dorsal portion of the tongue in rats to mimic embolization, and the post-operative recovery was reflected by the changes in the pixel dots of the extracted part of the blocked blood vessels, and it was observed that the blood flow in the area of the fine vessels was restored in about 3 days, whereas blood flow in the area of the large vessels was restored in only about 1 h. The method presented in this paper allows precise guidance of injectable filler HA, which has good application prospects in improving the safety of injection micro-plastic surgery and reducing the experience requirements for medical personnel.

Integrated Anionic Zirconium-Organic Cage and Cationic Boron-Imidazolate Cage for Synergetic Optical Limiting.

Making oppositely charged metal-organic cages (MOCs) into a tightly ordered structure may bring interesting functions. Herein, we report a novel structure composed of anionic (Zr4 L6 )8- (L=embonate) tetrahedral cages and in situ-formed cationic [Zn4 (Bim)4 ]4+ (Bim=[BH(im)3 ]- ; im=imidazole) cubic cages. Chiral transfer is observed from enantiopure (Zr4 L6 )8- cage to enantiopure [Zn4 (Bim)4 ]4+ cage. A pair of enantiomers (PTC-373(Δ) and PTC-373(Λ)) are formed. PTC-373 exhibits high chemical and thermal stabilities, affording an interesting single-crystal-to-single-crystal transformation. More importantly, the combination of ionic pair cages significantly enhances its third-order nonlinear optical property, and its thin-film exhibits an excellent optical limiting effect.

Lactobacillus induced by irbesartan on spontaneously hypertensive rat contribute to its antihypertensive effect.

OBJECTIVE: Hypertension is linked to gut dysbiosis. Here, the impact of the angiotensin receptor antagonist irbesartan on the gut microbiota of spontaneously hypertensive rats (SHR) were investigated. In addition, we assessed their contribution to its antihypertensive effect. METHODS: Eight-week-old Wistar-Kyoto (WKY) rats and SHR were administered irbesartan for 8 weeks. Fecal microbiota transplantation (FMT) was performed from SHR treated with irbesartan or untreated SHR to recipient untreated SHR. The preventive effect of Lactobacillus on hypertension in SHR was evaluated. Blood pressure (BP) was calculated using a tail-sleeve sphygmomanometer. To better assess the composition of the gut microbiota, the V3-V4 region of the 16S rRNA gene was amplified while short-chain fatty acids (SCFAs) in feces were tested by liquid chromatography-mass spectrometry/mass spectrometry (LC-MS/MS). RESULTS: Irbesartan restored gut dysbiosis, increased the abundance of Lactobacillus , and improved anti-inflammatory ability, antioxidative ability, intestinal integrity, and intestinal inflammation in SHR. The microbiota in SHR-treated irbesartan could reduce BP and improve antioxidative ability and gut integrity in SHR. Lactobacillus johnsonii ( L. johnsonii ) and Lactobacillus reuteri ( L. reuteri ) reduced BP, restored gut dysbiosis and improved anti-inflammatory ability, antioxidative ability, intestinal integrity in SHR. Most notably, irbesartan, L. johnsonii , and L. reuteri can significantly increase SCFA content in SHR feces. CONCLUSION: The current study demonstrated that irbesartan treatment ameliorated gut dysbiosis in SHR. Irbesartan induced alterations in gut microbiota, with increased prevalence of Lactobacillus .

The component of the Chamaecyparis obtusa essential oil and insecticidal activity against Tribolium castaneum (Herbst).

Tribolium castaneum (Herbst) is a worldwide grain storage pest controlled by chemical control methods of phosphine fumigation, which results in many hazards, damages human health, makes pests resistant to pesticides, and pollutes the environment. In recent years, the popularity of botanical insecticides has continued to rise, and plant essential oils (EO) are considered potential alternatives for developing insecticides. In the current study, we selected the Chamaecyparis obtusa EO to determine its insecticidal effects and component analysis on T. castaneum. Through gas chromatography-ion mobility spectrometry (GC-IMS) technology, cedrol was the most obvious compound in the signal peak of the volatile components detected in the C. obtusa EO. The results of the bioassay showed that the C. obtusa EO had certain contact activity against T. castaneum, and the LD50 was 52.54 µg/adult. At three concentrations (0.41,1.62, 2.83 uL/cm2), the repellent rates of C. obtusa EO against T. castaneum were all above 80% at 15, 30, 60, and 120 min, respectively, indicating that the repellent effect was strong. Meanwhile, the C. obtusa EO exhibited fumigant toxicity against T. castaneum with LC50 values of 7.09 µg/L air. In addition, C. obtusa EO significantly increased the activity of AChE, CarE, POD, CAT, T-SOD, and chitinase in T. castaneum. Finally, the mechanism of C. obtusa EO on T. castaneum adults was explored based on transcriptome sequencing. We found that the DEGs focused on the chitin metabolic process and some aging genes in T. castaneum. Therefore, C. obtusa EO could be used as potential eco-friendly candidates for stored grain pest management.

RNA interference of NADPH-cytochrome P450 reductase increases the susceptibility of Aphis gossypii Glover to sulfoxaflor.

NADPH-cytochrome P450 reductase (CPR) is essential for the detoxification of endogenous and exogenous substances mediated by cytochrome P450. While several insect CPRs have been found to be associated with insecticide resistance, the CPR of Aphis gossypii has not been characterized, and its functional role in insecticide resistance remains undefined. In this study, we cloned and characterized the full-length sequence of A. gossypii CPR (AgCPR). The deduced amino acid sequence of AgCPR contains all conserved domains of CPR, which shows high similarity to other insect CPRs and was clustered into a same branch of aphids according to phylogenetic analysis. The transcript of AgCPR was present in all developmental stages, with the highest expression in the adult stage. Furthermore, the expression of AgCPR could be induced by sulfoxaflor, a commonly used insecticide, in a time- and dose-dependent manner. Further silencing of AgCPR by feeding dsRNA significantly increased the susceptibility of A. gossypii to this insecticide. These findings suggest that AgCPR may play a significant role in the susceptibility of A. gossypii to sulfoxaflor and in the development of P450-mediated resistance to sulfoxaflor.

Calibration Method of a Wideband AC Resistance Voltage Divider Based on an Equivalent Model.

Aiming at the problem of large measurement error and phase shift in resistance voltage dividers under high-frequency conditions in the field of power measurement, such as power harmonics, an error correction method is proposed for an alternating current (AC) resistance voltage divider based on the equivalence principle. Firstly, the frequency error model of the AC resistance voltage divider precision is established, and the angle difference of the continuous spectrum ratio difference from 50 Hz to 100 kHz is corrected by determining the shielding structure and the resistance parameters and fine-tuning the shielding potential correction method to reduce the capacities error of the AC resistance voltage divider design precision. At the same time, the performance parameters such as the direction and magnitude of the shielding potential compensation capacitive error are investigated. Finally, the precision voltage divider (the maximum voltage applied is 480 V) calibration experiments verify that the important characteristic judgment factor of the voltage divider is independent of the frequency and the equivalent capacitance value, which effectively solves the phase correction problem of harmonic power measurement.

ZNF671 methylation test in cervical scrapings for cervical intraepithelial neoplasia grade 3 and cervical cancer detection.

Effective triage of high-risk human papillomavirus (hrHPV)+ women is warranted to avoid unnecessary referral and overtreatment. Molecular triage tests have recently begun to impact cervical intraepithelial neoplasia grade 3 (CIN3) or cervical cancer (CC), termed CIN3+, detection. We find that zinc finger protein 671 methylation (ZNF671m) test has superior performance for CIN3+ detection in all single molecular triage tests, including HPV16/18 genotyping, paired box gene 1 methylation (PAX1m), and ZNF671m, in the training set. Using ZNF671m test instead of Thinprep cytologic test (TCT) as a single triage strategy or as a combined triage strategy with HPV16/18 genotyping has achieved comparable sensitivity but higher specificity for CIN3+ detection among 391 hrHPV+ women in the validation set. Little attention has been paid to the women with hrHPV- status but detected CIN3+. We find that the CIN3+ risk after a negative result could be reduced further by triage using ZNF671m in hrHPV- patients.

pH-Responsive Biomaterials for the Treatment of Dental Caries-A Focussed and Critical Review.

Dental caries is a common and costly multifactorial biofilm disease caused by cariogenic bacteria that ferment carbohydrates to lactic acid, demineralizing the inorganic component of teeth. Therefore, low pH (pH 4.5) is a characteristic signal of the localised carious environment, compared to a healthy oral pH range (6.8 to 7.4). The development of pH-responsive delivery systems that release antibacterial agents in response to low pH has gained attention as a targeted therapy for dental caries. Release is triggered by high levels of acidogenic species and their reduction may select for the establishment of health-associated biofilm communities. Moreover, drug efficacy can be amplified by the modification of the delivery system to target adhesion to the plaque biofilm to extend the retention time of antimicrobial agents in the oral cavity. In this review, recent developments of different pH-responsive nanocarriers and their biofilm targeting mechanisms are discussed. This review critically discusses the current state of the art and innovations in the development and use of smart delivery materials for dental caries treatment. The authors' views for the future of the field are also presented.

Carbon dots doped with nitrogen as an ultrasensitive fluorescent probe for thrombin activity monitoring and inhibitor screening.

A simple and sensitive fluorometric assay based on nitrogen-doped carbon dots (N-CDs) was developed for the determination of thrombin (TB) activity in human serum samples and living cells. The novel N-CDs were prepared by a facile one-pot hydrothermal method using 1,2-ethylenediamine and levodopa as precursors. Such N-CDs exhibited green fluorescence with excitation/emission peaks at 390/520 nm and a high fluorescence quantum yield of approximately 39.2%. H-D-Phenylalanyl-L-pipecolyl-Larginine-p-nitroaniline-dihydrochloride (S-2238) was hydrolyzed by TB to produce p-nitroaniline which was capable of quenching the fluorescence of N-CDs due to an inner filter effect. This assay was used to detect TB activity with a low detection limit of 11.3 fM. The proposed sensing method was then expanded to the TB inhibitor screening and exhibited excellent applicability. As a typical TB inhibitor, argatroban was determined in a concentration as low as 1.43 nM. The method has also been successfully employed for the determination of TB activity in living HeLa cells. This work showed significant potential for TB activity assay in clinical and biomedicine applications.

Selected ssDNA aptamers-graphene oxide-based fluorescent biosensor to detect sulfameter in milk.

The abuse of sulfameter (SME) in animal husbandry can cause drug resistance and toxic or allergic reactions in humans. Therefore, it is very important to establish a simple, inexpensive, and efficient method for detecting SME in food. In this work, we propose a single fluorescent aptamer/graphene oxide (GO)-based biosensor to detect SME residues in milk. Aptamers that specifically bind to SME were screened using capture-SELEX and a ssDNA library immobilized on magnetic beads. The 68 active candidate aptamers were chemically synthesized for specificity and affinity characterization. Among the aptamers, the aptamer sulf-1 revealed the highest affinity (Kd = 77 ± 15 nM) to SME and was selected to construct a GO-based fluorescent biosensor for real milk sample detection. Under optimal conditions, the single fluorescent aptasensor had a wide linear range (R2 was 0.997) from 7 to 336 ng/ml and a low detection limit of 3.35 ng/ml that was calculated with a 3SD/slope. The single fluorescent method was also validated using SME-fortified milk samples, showing average recoveries ranging from 99.01% to 104.60% with a relative standard deviation of less than 3.88%. These results demonstrate that this novel aptamer sensor provides an opportunity for sensitive, convenient, and accurate detection of SME residues in milk.

Enhancing Third-Order Nonlinear Optical Property by Regulating Interaction between Zr4(embonate)6 Cage and N, N-Chelated Transition-Metal Cation.

Herein, the combination of anionic Zr4L6 (L = embonate) cages and N, N-chelated transition-metal cations leads to a series of new cage-based architectures, including ion pair structures (PTC-355 and PTC-356), dimer (PTC-357), and 3D frameworks (PTC-358 and PTC-359). Structural analyses show that PTC-358 exhibits a 2-fold interpenetrating framework with a 3,4-connected topology, and PTC-359 shows a 2-fold interpenetrating framework with a 4-connected dia network. Both PTC-358 and PTC-359 can be stable in air and other common solvents at room temperature. The investigations of third-order nonlinear optical (NLO) properties indicate that these materials show different degrees of optical limiting effects. It is surprising that increasing coordination interactions between anion and cation moieties can effectively enhance their third-order NLO properties, which can be attributed to the formation of coordination bonds that facilitate charge transfer. In addition, the phase purity, UV-vis spectra, and photocurrent properties of these materials were also studied. This work provides new ideas for the construction of third-order NLO materials.

Post-Assembly Modification of Homochiral Titanium-Organic Cages for Recognition and Separation of Molecular Isomers.

A chiral metal-organic cage (MOC) was extended and fixed into a porous framework using a post-assembly modification strategy, which made it easier to study the host-guest chemistry of the solid-state MOC using a single-crystal diffraction technique. Anionic Ti4 L6 (L=embonate) cage can be used as a 4-connecting crystal engineering tecton, and its optical resolution was achieved, thus homochiral ΔΔΔΔ- and ΛΛΛΛ-[Ti4 L6 ] cages were obtained. Accordingly, a pair of homochiral cage-based microporous frameworks (PTC-236(Δ) and PTC-236(Λ)) were easily prepared by a post-assembly reaction. PTC-236 has rich recognition sites provided by the Ti4 L6 moieties, chiral channels and high framework stability, affording a single-crystal-to-single-crystal transformation for guest structure analyses. Thus it was successfully utilized for the recognition and separation of isomeric molecules. This study provides a new approach for the orderly combination of well-defined MOCs into functional porous frameworks.

Synthesis and anti-HIV activity of non-nucleoside reverse-transcriptase inhibitor DB02 phosphate derivatives based on water-soluble optimization.

To improve the water solubility of anti-human immunodeficiency virus (HIV) agent DB02, an excellent non-nucleoside reverse-transcriptase inhibitor (NNRTI) obtained in our previous efforts, we designed and synthesized four phosphate derivatives of DB02 based on the molecular model of DB02 with RT. Here, the antiviral activity of these four derivatives was detected, leading to the discovery of compound P-2, which possessed a superior potency to the lead compound DB02 against wild-type HIV-1 and a variety of HIV-resistant mutant viruses significantly. Furthermore, the water solubility of P-2 was nearly 17 times higher than that of DB02, and the pharmacokinetic test in rats showed that P-2 demonstrate significantly improved oral bioavailablity of 14.6%. Our study showed that the introduction of a phosphate ester group at the end of the C-2 side chain of DB02 was beneficial to the improvement of its antiviral activity and pharmacokinetic properties, which provided a promising lead for the further development of S-DACOs type of NNRTIs.

Relationship between the Young's Moduli of Whole Microcapsules and Their Shell Material Established by Micromanipulation Measurements Based on Diametric Compression between Two Parallel Surfaces and Numerical Modelling.

Micromanipulation is a powerful technique to measure the mechanical properties of microparticles including microcapsules. For microparticles with a homogenous structure, their apparent Young's modulus can be determined from the force versus displacement data fitted by the classical Hertz model. Microcapsules can consist of a liquid core surrounded by a solid shell. Two Young's modulus values can be defined, i.e., the one is that determined using the Hertz model and another is the intrinsic Young's modulus of the shell material, which can be calculated from finite element analysis (FEA). In this study, the two Young's modulus values of microplastic-free plant-based microcapsules with a core of perfume oil (hexyl salicylate) were calculated using the aforementioned approaches. The apparent Young's modulus value of the whole microcapsules determined by the classical Hertz model was found to be EA = 0.095 ± 0.014 GPa by treating each individual microcapsule as a homogeneous solid spherical particle. The previously obtained simulation results from FEA were utilised to fit the micromanipulation data of individual core-shell microcapsules, enabling to determine their unique shell thickness to radius ratio (h/r)FEA = 0.132 ± 0.009 and the intrinsic Young's modulus of their shell (EFEA = 1.02 ± 0.13 GPa). Moreover, a novel theoretical relationship between the two Young's modulus values has been derived. It is found that the ratio of the two Young's module values (EA/EFEA) is only a function on the ratio of the shell thickness to radius (h/r) of the individual microcapsule, which can be fitted by a third-degree polynomial function of h/r. Such relationship has proven applicable to a broad spectrum of microcapsules (i.e., non-synthetic, synthetic, and double coated shells) regardless of their shell chemistry.

Standardizing image assessment in optical diffraction tomography.

Optical diffraction tomography (ODT) has gradually become a popular label-free imaging technique that offers diffraction-limited resolution by mapping an object's three-dimensional (3D) refractive index (RI) distribution. However, there is a lack of comprehensive quantitative image assessment metrics in ODT for studying how various experimental conditions influence image quality, and subsequently optimizing the experimental conditions. In this Letter, we propose to standardize the image assessment in ODT by proposing a set of metrics, including signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR), and structural distinguishability (SD). To test the feasibility of the metrics, we performed experiments on angle-scanning ODT by varying the number of illumination angles, RI contrast of samples, sample feature sizes, and sample types (e.g., standard polystyrene beads and 3D printed structures) and evaluated the RI tomograms with SNR, CNR, and SD. We further quantitatively studied how image quality can be improved, and tested the image assessment metrics on subcellular structures of living cells. We envision the proposed image assessment metrics may greatly benefit end-users for assessing the RI tomograms, as well as experimentalists for optimizing ODT instruments.

Complex wave and phase retrieval from a single off-axis interferogram.

Single-frame off-axis holographic reconstruction is promising for quantitative phase imaging. However, reconstruction accuracy and contrast are degraded by noise, frequency spectrum overlap of the interferogram, severe phase distortion, etc. In this work, we propose an iterative single-frame complex wave retrieval based on an explicit model of object and reference waves. We also develop a phase restoration algorithm that does not resort to phase unwrapping. Both simulation and real experiments demonstrate higher accuracy and robustness compared to state-of-the-art methods, for both complex wave estimation and phase reconstruction. Importantly, the allowed bandwidth for the object wave is significantly improved in realistic experimental conditions (similar amplitudes for object and reference waves), which makes it attractive for large field-of-view and high-resolution imaging applications.