RESUMO
Dried spaghetti was rehydrated to its optimal cooking state, known as al dente, at 60, 80, and 100 °C, in distilled water or 0.1, 1.0, and 2.0 mol/L sodium chloride solutions. Then, the moisture distributions and stress-strain curves were examined to identify the major factors governing the texture of rehydrated spaghetti. The difference in moisture content between the inner and peripheral regions of rehydrated spaghetti and its breaking stress were greater at higher rehydration temperatures; however, rehydration temperature did not affect breaking strain. The sodium chloride concentration of the immersion solution did not affect moisture distribution or breaking stress, while breaking strain was decreased by rehydration at higher sodium chloride concentrations. The results obtained in this study suggest that moisture distribution within spaghetti and its material properties govern its breaking stress and strain, respectively.
Assuntos
Carboidratos/química , Água/química , CulináriaRESUMO
The effects of mechanical stress during emulsification on the oxidation of methyl linoleate were investigated by four methods (high-pressure homogenization, high-speed stirring, ultrasonic homogenization, and membrane emulsification). The oxidation rates and induction periods were almost constant, regardless of the emulsification method, except for membrane emulsification, by which the induction period was prolonged when a cellulose acetate membrane was used.
Assuntos
Ácidos Linoleicos/química , Celulose/análogos & derivados , Celulose/química , Emulsões , Membranas Artificiais , Oxirredução , Pressão , Estresse Mecânico , UltrassomRESUMO
A novel method for preparing a finely dispersed oil-in-water emulsion is proposed. Octanoic acid dissolved in water at a high temperature of 220 or 230 degrees C at 15 MPa was combined with an aqueous solution of a surfactant and then the mixture was cooled. When a nonionic surfactant, decaglycerol monolaurate (ML-750) or polyoxyethylene sorbitan monolaurate (Tween 20), was used, fine emulsions with a median oil droplet diameter of 100 nm or less were successfully prepared at ML-750 and Tween 20 concentrations of 0.083% (w/v) and 0.042%, respectively, or higher. The diameters were much smaller than those of oil droplets prepared by the conventional homogenization method using a rotor/stator homogenizer. However, an anionic surfactant, sodium dodecyl sulfate, was not adequate for the preparation of such fine emulsions by the proposed method. Although the interfacial tensions between octanoic acid and the surfactant solutions were measured at different temperatures, they were not an indication for selecting a surfactant for the successful preparation of the fine emulsion by the proposed method.
Assuntos
Emulsões/síntese química , Temperatura Alta , Óleos/química , Água/química , Caprilatos/química , Emulsões/química , Glicerol/análogos & derivados , Glicerol/química , Lauratos/química , Tamanho da Partícula , Polissorbatos/química , Dodecilsulfato de Sódio/química , Tensão Superficial , Tensoativos/químicaRESUMO
Spaghetti was prepared using dies made of different materials. The surface was observed using digital and optical microscopes, and was rougher for the spaghettis prepared using the Teflon, polypropylene, polycarbonate, aluminum, and bronze dies in this order. The extrusion velocity when passing through the die was faster, the bulk density was higher, and the rupture strength was greater for the spaghetti having the smoother surface. The die material did not affect the gelatinization temperature. The water sorption curves in boiling water containing 0.5% (w/v) sodium chloride were also observed. The curves were expressed by an equation of the hyperbolic type except for the early stage of sorption in order to estimate the equilibrium amount of water sorbed based on the bone-dry sample. The momentarily-sorbed amount of water, which is a hypothetical quantity to characterize the initial water intake, was estimated by fitting the experimental points within 60 s. The amount was higher for the spaghetti having the rougher surface.
Assuntos
Culinária , Propriedades de Superfície , Água/química , Alumínio/análise , Alumínio/química , Teste de Materiais , Cimento de Policarboxilato/análise , Cimento de Policarboxilato/química , Polipropilenos/análise , Polipropilenos/química , Politetrafluoretileno/análise , Politetrafluoretileno/químicaRESUMO
The distribution coefficients of four hydrophobic solutes onto a porous styrene divinylbenzene resin were measured using methanol-water mixtures with a low methanol content as the eluent at various temperatures. The temperature dependence of the distribution coefficients indicated that the elution times of the solutes were controllable by elevating the temperature even for the eluent with a low methanol content.
Assuntos
Metanol/análise , Poliestirenos/química , Adsorção , Cromatografia Líquida , Temperatura , TermodinâmicaRESUMO
Linoleic acid was encapsulated with a soluble soybean polysaccharide, gum arabic, or a mixture of both together with maltodextrin, and the oxidation process of the encapsulated acid was measured at 37 degrees C and at a relative humidity of 12%. The soybean polysaccharide was more effective for encapsulating the acid and suppressing the oxidation of the encapsulated acid than gum arabic. A mixture of the soybean polysaccharide and maltodextrin was also effective for this purpose when the weight fraction of the polysaccharide was equal to or greater than 0.75.