Hardness and surface roughness of enamel and base layers of resin denture teeth after long-term repeated chemical disinfection.

AIM: To evaluate the effect of successive cycles of disinfection in different denture cleansers on the surface roughness and the Vickers hardness of two layers of acrylic resin (base-BL and enamel-EL) of two commercial cross-linked artificial teeth. MATERIALS AND METHODS: The occlusal surfaces of 60 acrylic resin denture posterior teeth (Trilux-TLX and SR Orthosit PE-SRO) embedded in autopolymerizing acrylic resin were ground fat with 1200-grit silicon carbide paper. Specimens were stored in distilled water at 37°C and then submitted to the microhardness (VHN) and roughness (µm) tests. Specimens were stored in distilled water at 37°C for 90 days and submitted to 720 disinfection cycles in sodium hypochlorite at 0.5%, 30% vinegar solution or distilled water (control). Afterward, micro-hardness and roughness tests were again performed. Data were analyzed using two-way ANOVA and Tukey's test (α=0.05). RESULTS: Hypochlorite immersion decreased the hardness of BL and EL of SRO teeth, with an average reduction of 10.11% (p<0.008). TLX teeth demonstrated a hardness reduction of 28.96% of both layers for all solutions including water (p<0.0000). The roughness of both teeth was not affected by denture cleansers (p>0.37). CONCLUSION: Hypochlorite promoted deleterious effects on the hardness of both layers of the artificial teeth tested. Immersion in vinegar and water also resulted in reduction of hardness of TLX teeth. CLINICAL SIGNIFICANCE: The surface hardness of the different layers of cross-linked artificial teeth can be altered by daily disinfection in denture cleansers commonly indicated for removable dentures.

Influence of technique and manipulation on self-adhesive resin cements used to cement intraradicular posts.

STATEMENT OF PROBLEM: Resin cements are widely used to cement intraradicular posts, but bond strength is significantly influenced by the technique and material used for cementation. PURPOSE: The purpose of this study was to evaluate the bond strength of 3 self-adhesive cements used to cement intraradicular glass fiber posts. The cements all required different application and handling techniques. MATERIAL AND METHODS: Forty-five human maxillary canines were selected and randomly divided into 3 groups n= 15 by drawing lots: Group BIS - Biscem, Group BRE - Breeze, and Group MAX - Maxcem. Each group was divided into 3 subgroups according to application and handling techniques: Sub-group A - Automix/Point tip applicator, Sub-group L - Handmix/Lentulo, and Sub-group C - Handmix/Centrix. Cementation of the posts was performed according to the manufacturers' instructions. The push-out test was performed with a crosshead speed of 0.5 mm/min, and bond strength was expressed in megapascals. The results were evaluated by 2-way ANOVA and the all pairwise multiple comparison procedures (Tukey test) (α=.05). RESULTS: Breeze cement showed the highest average for the subgroups A, L, and C when compared to the Biscem cement and Maxcem Elite (P<.05). Statistically significant differences among the subgroups were only observed for Biscem. CONCLUSIONS: This study shows that application and handling techniques may influence the bond strength of different self-adhesive cements when used for intraradicular post cementation.

Gingival recession in individuals with cleft lip and palate: prevalence and severity.

OBJECTIVE: To analyze the prevalence and severity of gingival recession in individuals with cleft lip and alveolus with or without cleft palate. DESIGN: Cross-sectional. SETTING: Tertiary referral hospital. PARTICIPANTS: A total of 400 individuals with cleft lip and alveolus with or without cleft palate, aged 15 to 49 years, without any previous periodontal treatment. MAIN OUTCOME MEASURES: Gingival recession was evaluated by measuring the distance from the cementoenamel junction to the most coronal point on the gingival margin, analyzing the prevalence and scoring its severity as mild (<3 mm), moderate (3 to 4 mm), or severe (4 mm). The prevalence and severity of gingival recession was compared between sextant 2 (cleft sextant) and the mean of the other sextants (1, 3, 4, 5, and 6: noncleft sextants). The relationship between gingival recession in the cleft area and gender was evaluated and data were analyzed statistically. The correlation between gingival recession and age was assessed also. RESULTS: There was no statistically significant gender difference in gingival recession. The prevalence and severity of gingival recession increased with age, and most of the affected teeth were premolars and molars. The cleft area did not present a higher prevalence and severity of gingival recession. CONCLUSIONS: Individuals with cleft lip and alveolus with or without cleft palate presented the same prevalence and severity of gingival recession compared with other populations. The area adjacent to the cleft (sextant 2) did not show greater risk of gingival recession than other areas (sextants 1, 3, 4, 5, and 6).

Influence of the composition and shades of ceramics on light transmission and degree of conversion of dual-cured resin cements.

OBJECTIVE: Since the transmittance of ceramics can influence the degree of conversion (DC) of resin cements, ceramics composition and shade should be considered in the selection of resin cement. This in vitro study aimed to evaluate the effect of the transmittance of different composition, opacities and shades of ceramics on the degree of conversion of two dual-cured resin cements. METHODOLOGY: Sixty discs were prepared from low translucency (LT) and medium opacity (MO) lithium disilicate ceramic, and zirconia ceramic (Z). Each group was subdivided into 5 subgroups (n=4) in shades A2, A3.5, B2, C2 and D3. The transmittance measurement was performed in a spectrophotometer. The Variolink II and Rely X U200 resin cements were photoactivated by LED (1400 mW/cm2) for 40 s through the ceramic discs and without the discs (control group). The DC was measured with infrared FTIR spectroscopy, immediately after light activation. Data were analyzed with Kruskall-Wallis and one-way ANOVA, following post-hoc comparisons by Tukey test and Pearson's correlation test (P<0.05). RESULTS: LT ceramic exhibited higher transmittance values compared to MO and Z ceramics. LTA2 and LTB2 showed statistically higher transmittance values compared to MOA2, MOA3.5 and ZA3.5. For Variolink II, the ceramic interposition did not influence the DC, since there were no statistical differences between groups with ceramic interposition and the control group. For Rely X U200 cement, the interposition of some ceramics types/shades (LTA3.5, MOA2, MOA3.5 and ZA3.5) significantly decreased the DC values compared to control group. A positive correlation was found between the ceramic transmittance and DC values of both tested cements. Conclusions. The transmittance and DC values of the cements were influenced by composition and shades of the ceramics. The higher the transmittance of ceramics, the higher the DC values for both cements.

Effect of aging and testing method on bond strength of CAD/CAM fiber-reinforced composite to dentin.

OBJECTIVES: To evaluate and compare the outcomes of shear (S) and microtensile (µT) bond strength tests of CAD/CAM fiber-reinforced composite (FRC) to dentin. Aging with either fatigue or thermocycling were conducted for comparison with baseline microtensile group. METHODS: CAD/CAM FRC (Trinia, Bicon LLC, Boston, USA) blocks were milled to 3-mm diameter cylinders for shear and to blocks (5×5×5mm) for µT. Sixty extracted human molars were flattened to obtain dentin surfaces and randomly divided in four groups (n=15): (1) SC: samples tested in shear 24h after bonding; (2) µTC: samples tested in µT 24h after bonding); (3) µTF: samples submitted to mechanical fatigue prior to µT test, and; (4) µTT: thermocycling prior to µT test. Bonding system was applied onto the FRC material (Cera-Resin Bond, CRB, Shofu Dental, Kyoto, Japan). A conventional three-step adhesive system (All-bond 3, Bisco, Schaumburg, USA) was use with a self-cure resin cement (C&B resin cement, Bisco, Schaumburg, USA). Bond strength tests were conducted at 0.75mm/min and data analyzed using Weibull distribution (p<0.05). RESULTS: Weibull contour plots showed a significantly lower characteristic strength (η) and Weibull modulus (m) for SC (η=6.9MPa and m=1.4) compared to µTC (η=20.9MPa and m=4.5). Fatigued and thermocycled µT groups presented significantly reduced characteristic strength (η=3.1MPa and η=4.1MPa, respectively) compared to µTC. Weibull modulus was significantly reduced only for SC and µTF groups compared µTC. Failure predominantly occurred at the cement/FRC interface. SIGNIFICANCE: FRC bonded to dentin samples presented lower Weibull modulus and characteristic bond strength when immediately tested in shear compared to microtensile. Aging through thermocycling or mechanical fatigue significantly reduced the characteristic strength in microtensile testing, with the majority of failures emerging between restoration material and cement interface.

Measurement properties of gingival biotype evaluation methods.

BACKGROUND: There are numerous methods to measure the dimensions of the gingival tissue, but few have compared the effectiveness of one method over another. OBJECTIVE: This study aimed to describe a new method and to estimate the validity of gingival biotype assessment with the aid of computed tomography scanning (CTS). MATERIALS AND METHODS: In each patient different methods of evaluation of the gingival thickness were used: transparency of periodontal probe, transgingival, photography, and a new method of CTS). Intrarater and interrater reliability considering the categorical classification of the gingival biotype were estimated with Cohen's kappa coefficient, intraclass correlation coefficient (ICC), and ANOVA (P < .05). The criterion validity of the CTS was determined using the transgingival method as the reference standard. Sensitivity and specificity values were computed along with theirs 95% CI. RESULTS: Twelve patients were subjected to assessment of their gingival thickness. The highest agreement was found between transgingival and CTS (86.1%). The comparison between the categorical classifications of CTS and the transgingival method (reference standard) showed high specificity (94.92%) and low sensitivity (53.85%) for definition of a thin biotype. CONCLUSION: The new method of CTS assessment to classify gingival tissue thickness can be considered reliable and clinically useful to diagnose thick biotype.

Influence of curing protocol and ceramic composition on the degree of conversion of resin cement.

OBJECTIVE: Due to increasing of aesthetic demand, ceramic crowns are widely used in different situations. However, to obtain long-term prognosis of restorations, a good conversion of resin cement is necessary. To evaluate the degree of conversion (DC) of one light-cure and two dual-cure resin cements under a simulated clinical cementation of ceramic crowns. MATERIAL AND METHODS: Prepared teeth were randomly split according to the ceramic's material, resin cement and curing protocol. The crowns were cemented as per manufacturer's directions and photoactivated either from occlusal suface only for 60 s; or from the buccal, occlusal and lingual surfaces, with an exposure time of 20 s on each aspect. After cementation, the specimens were stored in deionized water at 37°C for 7 days. Specimens were transversally sectioned from occlusal to cervical surfaces and the DC was determined along the cement line with three measurements taken and averaged from the buccal, lingual and approximal aspects using micro-Raman spectroscopy (Alpha 300R/WITec®). Data were analyzed by 3-way ANOVA and Tukey test at =5%. RESULTS: Statistical analysis showed significant differences among cements, curing protocols and ceramic type (p<0.001). The curing protocol 3x20 resulted in higher DC for all tested conditions; lower DC was observed for Zr ceramic crowns; Duolink resin cement culminated in higher DC regardless ceramic composition and curing protocol. CONCLUSION: The DC of resin cement layers was dependent on the curing protocol and type of ceramic.

Noncarious cervical lesions in adults: prevalence and occlusal aspects.

BACKGROUND: The factors that induce the formation of noncarious lesions are not understood fully, particularly those that are related to occlusal aspects. The authors conducted a study to evaluate the prevalence of noncarious cervical lesions in adults and their association with occlusal aspects. METHODS: The authors examined 70 people (35 men and 35 women) aged 25 to 45 years to determine the presence and type of noncarious cervical lesions, wear facets, tooth contacts in maximal intercuspal position, and lateral and protrusive movements. The assessment involved a questionnaire and clinical examination. RESULTS: Among the teeth the authors evaluated, 17.23 percent had cervical lesions, 80.28 percent of which had wear facets (P < .01). The authors found a significant difference between the prevalence of noncarious lesions and the presence of wear facets (P = .0484). CONCLUSIONS: The authors found that cervical lesions were related significantly to wear facets. These findings strengthen evidence for the role of occlusal forces as an etiologic factor for noncarious lesions. CLINICAL IMPLICATIONS: The presence of wear facets should be considered in the treatment of noncarious cervical lesions.

Effect of conventional water-bath and experimental microwave polymerization cycles on the flexural properties of denture base acrylic resins.

The effect of polymerization cycles on flexural properties of conventional (Vipi Cril(®)-VC) or microwave-processed (Vipi Wave(®)-VW) denture base acrylic resins was evaluated. Specimens (n=10) were submitted to the cycles: WB=65ºC for 1 h+1 h boiling water (VC cycle); M630/25=10 min at 270 W+5 min at 0 W+10 min at 360 W (VW cycle); M650/5=5 min at 650 W; M700/4=4 min at 700 W; and M550/3=3 min at 550 W. Specimens were submitted to a three-point bending test at 5 mm/min until fracture. Flexural strength (MPa) and elastic modulus (GPa) data were analyzed by 2-way ANOVA/Tukey HSD (α=0.05). Overall, VC showed higher values than VW. The results obtained with microwave polymerization did not differ from those obtained with water-bath for both acrylic resins. The results observed when polymerization cycles using medium power and shorter time were used did not differ from those when manufacturer's recommended microwave cycle was applied. Conventional VC might be microwave-processed without compromising its flexural properties.

Effects of coronal substrates and water storage on the microhardness of a resin cement used for luting ceramic crowns.

UNLABELLED: Composite resin and metallic posts are the materials most employed for reconstruction of teeth presenting partial or total destruction of crowns. Resin-based cements have been widely used for cementation of ceramic crowns. The success of cementation depends on the achievement of adequate cement curing. OBJECTIVES: To evaluate the microhardness of Variolink® II (Ivoclar Vivadent, Schaan, Liechtenstein), used for cementing ceramic crowns onto three different coronal substrate preparations (dentin, metal, and composite resin), after 7 days and 3 months of water storage. The evaluation was performed along the cement line in the cervical, medium and occlusal thirds on the buccal and lingual aspects, and on the occlusal surface. MATERIAL AND METHODS: Thirty molars were distributed in three groups (N=10) according to the type of coronal substrate: Group D- the prepared surfaces were kept in dentin; Groups M (metal) and R (resin)- the crowns were sectioned at the level of the cementoenamel junction and restored with metallic cast posts or resin build-up cores, respectively. The crowns were fabricated in ceramic IPS e.max® Press (Ivoclar Vivadent, Schaan, Liechtenstein) and luted with Variolink II. After 7 days of water storage, 5 specimens of each group were sectioned in buccolingual direction for microhardness measurements. The other specimens (N=5) were kept stored in deionized water at 37ºC for three months, followed by sectioning and microhardness measurements. RESULTS: Data were first analyzed by three-way ANOVA that did not reveal significant differences between thirds and occlusal surface (p=0.231). Two-way ANOVA showed significant effect of substrates (p<0.001) and the Tukey test revealed that microhardness was significantly lower when crowns were cemented on resin cores and tested after 7 days of water storage (p=0.007). CONCLUSION: The type of material employed for coronal reconstruction of preparations for prosthetic purposes may influence the cement properties.

Influence of the composition and shades of ceramics on light transmission and degree of conversion of dual-cured resin cements

Abstract Objective Since the transmittance of ceramics can influence the degree of conversion (DC) of resin cements, ceramics composition and shade should be considered in the selection of resin cement. This in vitro study aimed to evaluate the effect of the transmittance of different composition, opacities and shades of ceramics on the degree of conversion of two dual-cured resin cements. Methodology Sixty discs were prepared from low translucency (LT) and medium opacity (MO) lithium disilicate ceramic, and zirconia ceramic (Z). Each group was subdivided into 5 subgroups (n=4) in shades A2, A3.5, B2, C2 and D3. The transmittance measurement was performed in a spectrophotometer. The Variolink II and Rely X U200 resin cements were photoactivated by LED (1400 mW/cm2) for 40 s through the ceramic discs and without the discs (control group). The DC was measured with infrared FTIR spectroscopy, immediately after light activation. Data were analyzed with Kruskall-Wallis and one-way ANOVA, following post-hoc comparisons by Tukey test and Pearson's correlation test (P<0.05). Results LT ceramic exhibited higher transmittance values compared to MO and Z ceramics. LTA2 and LTB2 showed statistically higher transmittance values compared to MOA2, MOA3.5 and ZA3.5. For Variolink II, the ceramic interposition did not influence the DC, since there were no statistical differences between groups with ceramic interposition and the control group. For Rely X U200 cement, the interposition of some ceramics types/shades (LTA3.5, MOA2, MOA3.5 and ZA3.5) significantly decreased the DC values compared to control group. A positive correlation was found between the ceramic transmittance and DC values of both tested cements. Conclusions. The transmittance and DC values of the cements were influenced by composition and shades of the ceramics. The higher the transmittance of ceramics, the higher the DC values for both cements.

O impacto positivo na promoção de saúde bucal em jovens adolescentes / The Positive Impact on Oral Health Promotion in Young Adolescents

Introdução: o conhecimento da importância dos cuidados em saúde bucal é deficiente em âmbito escolar, ressalta-se que jovens capacitados, partilham o aprendizado assumindo papel importante na sociedade. Objetivos: capacitação de estudantes para difusão do conhecimento sobre cuidados em saúde bucal. Os temas de higienização dentária/prótese dentária e/ou implantossuportadadas e manejo após o traumatismo dentário foram abordados em escola pública. Métodos: Inicialmente, houve avaliação do conhecimento prévio dos alunos (n=25) por meio de questionários de saúde bucal, os questionários (GOHAI, higienização oral e de prótese dentária e manejo de traumatismo dentário) foram aplicados na sala de aula com supervisão. Em um próximo momento houve o treinamento dos discentes por palestras e material didático. Finalmente, após 2 meses do ciclo de formação os questionários foram aplicados novamente. Os dados foram tabulados e e análise estatística considerou o valor significativo para p<0,05, a fim de verificar o conhecimento adquirido durante o treinamento de todos os estudantes. Resultados: Identificou se pós-oficina que os jovens estavam mais satisfeitos com a aparência da boca (p<0,05). Nos questionários de higienização de próteses dentárias houve a conscientização do tempo para substituição das mesmas. Para o reimplante dentário, houve significativa percepção dos alunos como possibilidade de terapia real (p=0,016), após a realização das oficinas. Conclusão: com base nos dados, a proposta de promoção em saúde bucal para os adolescentes foi eficiente, e mais eventos (oficinas) com esta finalidade devem ser realizados em escolas de ensino médio.

Introduction: the knowledge of the importance of oral health care is deficient in the school environment, it is emphasized that empowered young people share learning, assuming an important role in society. Objectives: This study aimed to enable the training of students to disseminate knowledge about oral health care. The subjects of dental hygiene / dental prosthesis and / or implant supported and management after dental trauma were addressed in a public school. Methods: Initially, the students' prior knowledge (n = 25) was assessed through oral health questionnaires, the questionnaires (GOHAI, oral and dental hygiene and dental trauma management) were applied in the classroom with supervision. In a next moment there was the training of the students by lectures and didactic material. Finally, after 2 months of the training cycle, the questionnaires were applied again. Data were tabulated and statistical analysis considered the value significant for p students. Results: It was identified after the workshop that young people were more satisfied with the appearance of the mouth (p<0,05).In the dental prosthesis cleaning questionnaires, there was a time awareness for their replacement. For dental replantation, there was significant perception of students as a possibility of real therapy (p = 0.016), after the workshops. Conclusion: Based on the data, the proposal for oral health promotion for adolescents was efficient, and more events (workshops) for this purpose should be held in high schools.

Effects of curing protocol and storage time on the micro-hardness of resin cements used to lute fiber-reinforced resin posts.

OBJECTIVES: To determine the micro-hardness profile of two dual cure resin cements (RelyX-U100, 3M-eSPe and Panavia F 2.0, Kuraray) used for cementing fiberre inforced resin posts (Fibrekor-Jeneric Pentron) under three different curing protocols and two water storage times. MATERIAL AND METHODS: Sixty 16 mm long bovine incisor roots were endodontically treated and prepared for cementation of the Fibrekor posts. The cements were mixed as instructed, dispensed in the canal, the posts were seated and the curing performed as follows: (a) no light activation; (b) light-activation immediately after seating the post, and; (c) light-activation delayed 5 minutes after seating the post. The teeth were stored in water and retrieved for analysis after 7 days and 3 months. The roots were longitudinally sectioned and the microhardness was determined at the cervical, middle and apical regions along the cement line. The data was analyzed by the three-way ANOVA test (curing mode, storage time and thirds) for each cement. The Tukey test was used for the post-hoc analysis. RESULTS: Light-activation resulted in a significant increase in the microhardness. This was more evident for the cervical region and for the Panavia cement. Storage in water for 3 months caused a reduction of the micro-hardness for both cements. The U100 cement showed less variation in the micro-hardness regardless of the curing protocol and storage time. CONCLUSIONS: The micro-hardness of the cements was affected by the curing and storage variables and were material-dependent.

Influence of curing protocol and ceramic composition on the degree of conversion of resin cement

Abstract Due to increasing of aesthetic demand, ceramic crowns are widely used in different situations. However, to obtain long-term prognosis of restorations, a good conversion of resin cement is necessary. Objective: To evaluate the degree of conversion (DC) of one light-cure and two dual-cure resin cements under a simulated clinical cementation of ceramic crowns. Material and Methods: Prepared teeth were randomly split according to the ceramic's material, resin cement and curing protocol. The crowns were cemented as per manufacturer's directions and photoactivated either from occlusal suface only for 60 s; or from the buccal, occlusal and lingual surfaces, with an exposure time of 20 s on each aspect. After cementation, the specimens were stored in deionized water at 37°C for 7 days. Specimens were transversally sectioned from occlusal to cervical surfaces and the DC was determined along the cement line with three measurements taken and averaged from the buccal, lingual and approximal aspects using micro-Raman spectroscopy (Alpha 300R/WITec®). Data were analyzed by 3-way ANOVA and Tukey test at =5%. Results: Statistical analysis showed significant differences among cements, curing protocols and ceramic type (p<0.001). The curing protocol 3x20 resulted in higher DC for all tested conditions; lower DC was observed for Zr ceramic crowns; Duolink resin cement culminated in higher DC regardless ceramic composition and curing protocol. Conclusion: The DC of resin cement layers was dependent on the curing protocol and type of ceramic.

Atividade antibacteriana de cimentos endodônticos puros e acrescidos de antibióticos contra duas linhagens ATCC de Enterococcus faecalis / Antibacterial activity of pure endodontic sealers and antibiotic-loaded sealers against two ATCC strains of Enterococcus faecalis

Introdução: canais radiculares necrosados e não tratados se caracterizam pela presença de uma microbiota mista e polimicrobiana.O E. faecalis demonstra alta resistência a medicamentos usados durante o tratamento endodôntico, sendo um dos poucos microrganismos que tem demonstrado in vitro resistir ao efeito antibacteriano do hidróxido de cálcio. Além disso, é a espécie bacteriana mais frequentemente isolada, com prevalência variando entre 29% e 77% nos canais radiculares de dentes com insucesso endodôntico. Objetivo: avaliar a atividade antibacteriana dos cimentos endodônticos MTA Fillapex, Sealapex, Sealer 26 e Endofill puros e acrescidos de amoxicilina e ciprofloxacina frente a duas linhagens ATCC de Enterococcus faecalis (ATCC 29212 e ATCC 4083). Método: os testes foram realizados pela técnica de difusão radial dos cimentos aplicados diretamente no ágar, impregnados em discos de papel aplicados sobre o ágar e pelo teste de contato direto. Para a análise estatística utilizaram-se os testes de ANOVA e Tukey com nível de significância de 5%. Resultados e Discussão: os resultados mostraram que pela técnica da difusão radial, considerando os cimentos puros, o Sealapex foi o único que apresentou halo de inibição frente às duas linhagens. Já, quando da associação da amoxicilina e ciprofloxacina o MTA Fillapex demonstrou os melhores halos de inibição para as duas linhagens. Todos os cimentos tiveram a ação potencializada pela adição dos antibióticos (p<0,05). Pela técnica de difusão dos cimentos impregnados em discos de papel, o cimento Sealapex puro fresco revelou atividade antimicrobiana e também em todas as variáveis de tempo. Quando acrescidos os antibióticos, todos os cimentos tiveram a ação antimicrobiana potencializada pelas drogas, em todas as variáveis de tempo. Este mesmo resultado foi observado na técnica do contato direto dos cimentos com ambas as linhagens. Conclusão: a atividade antibacteriana, frente ao E. faecalis, dos cimentos MTA Fillapex, Endofill, Sealer e Sealapex acrescidos os antibióticos amoxicilina e ciprofloxacina, é potencializada mesmo após um longo período da presa dos cimentos.

Introduction: necrotic root canals and untreated are characterized by the presence of a mixed and polymicrobial flora. E. faecalis show high resistance to drugs used during endodontic treatment, one of the few microorganisms which have shown in vitro to resist the antibacterial effect of calcium hydroxide. Furthermore, it is the bacterial species most often isolated, with a prevalence ranging between 29% and 77%, in root canals of teeth with endodontic failure. Objective: the aim of this study was to evaluate the antibacterial activity of the sealers MTA Fillapex, Sealapex, Sealer 26 and Endofill, pure and loaded with amoxicillin and ciprofloxacin against two ATCC strains of Enterococcus faecalis (ATCC 29212 and ATCC 4083). Method: the tests were conducted by means of radial diffusion technique of the cement applied in to the agar, impregnated paper discs applied on the agar and by the direct contact test. For the statistical analysis, the ANOVA and the Tukey?s test were used at a 5% significance level. Results and Discussion: results showed that, through the technique of radial diffusion, regarding the pure cements, the Sealapex was the only one that showed inhibition halo for the two strains. However, considering the association of amoxicillin and ciprofloxacin Fillapex, the MTA showed better inhibition zones for the two strains. All cements had their actions enhanced by with addition of antibiotics (p <0.05). Through the technique of diffusion of cements impregnated in paper discs, the Sealapex pure fresh cement revealed an antimicrobial activity and also in all the variables of time. When loaded with antibiotics, all cements had the antimicrobial action potentiated by drugs in all variables of time. The same result was observed in the technique of direct contact of cement with both strains. Conclusionn: the antibacterial activity against the E. faecalis, of the cements MTA Fillapex, Endofill, Sealer and Sealapex loaded with the antibiotics amoxicillin and ciprofloxacin, is enhanced even after a long period of use of cements.

Microhardness of resin cements in the intraradicular environment: effects of water storage and softening treament.

OBJECTIVES: To analyze the microhardness of four dual-cure resin cements used for cementing fiber-reinforced posts under the following conditions: after 7 days of storage in water, after additional 24h of immersion in 75% ethanol, and after 3 months of storage in water. Hardness measurements were taken at the cervical, middle and apical thirds along the cement line. METHODS: Root canals of 40 bovine incisors were prepared for post space. Fibrekor glass fiber-reinforced posts (Jeneric/Pentron) of 1mm in diameter were cemented using Panavia F 2.0 (Kuraray), Variolink (Ivoclar-Vivadent), Rely X Unicem (3M ESPE) or Duolink (Bisco) (N=10). After 7 days of water storage at 37 degrees C, half the sample (N=5) was longitudinally sectioned and the initial microhardness measured along the cement line from cervical to apex. These same samples were further immersed in 75% ethanol for 24h and reassessed. The remaining half (N=5) was kept unsectioned in deionized water at 37 degrees C for 3 months, followed by sectioning and measuring. Data were analyzed by a series of two-way ANOVA and Tukey tests at alpha=5%. RESULTS: Statistically significant differences were identified among the cements, thirds and conditions. Significant interactions were also observed between cements and thirds and between cements and conditions. Panavia F exhibited significantly higher initial microhardness than the other three cements, which showed no statistical difference among themselves. Variolink and Duolink showed significantly higher microhardness values in the cervical third, without significant difference among the thirds for the other cements. Immersion in ethanol significantly reduced the hardness values for all cements, regardless of the thirds. Storage in water for 3 months had no influence on the hardness of most of the cements, with the exception of Unicem that showed a significant increase in the hardness values after this period. SIGNIFICANCE: Results showed heterogeneity in the microhardness of the cements inside the canal. All cements presented some degree of softening after ethanol treatment, which suggests instability of the polymer. The quality of curing of resin cements in the root canal environment seems unpredictable and highly material dependent.

Effects of coronal substrates and water storage on the microhardness of a resin cement used for luting ceramic crowns

Composite resin and metallic posts are the materials most employed for reconstruction of teeth presenting partial or total destruction of crowns. Resin-based cements have been widely used for cementation of ceramic crowns. The success of cementation depends on the achievement of adequate cement curing. Objectives: To evaluate the microhardness of Variolink® II (Ivoclar Vivadent, Schaan, Liechtenstein), used for cementing ceramic crowns onto three different coronal substrate preparations (dentin, metal, and composite resin), after 7 days and 3 months of water storage. The evaluation was performed along the cement line in the cervical, medium and occlusal thirds on the buccal and lingual aspects, and on the occlusal surface. Material and Methods: Thirty molars were distributed in three groups (N=10) according to the type of coronal substrate: Group D- the prepared surfaces were kept in dentin; Groups M (metal) and R (resin)- the crowns were sectioned at the level of the cementoenamel junction and restored with metallic cast posts or resin build-up cores, respectively. The crowns were fabricated in ceramic IPS e.max® Press (Ivoclar Vivadent, Schaan, Liechtenstein) and luted with Variolink II. After 7 days of water storage, 5 specimens of each group were sectioned in buccolingual direction for microhardness measurements. The other specimens (N=5) were kept stored in deionized water at 37ºC for three months, followed by sectioning and microhardness measurements. Results: Data were first analyzed by three-way ANOVA that did not reveal significant differences between thirds and occlusal surface (p=0.231). Two-way ANOVA showed significant effect of substrates (p<0.001) and the Tukey test revealed that microhardness was significantly lower when crowns were cemented on resin cores and tested after 7 days of water storage (p=0.007). Conclusion: The type of material employed for coronal reconstruction of preparations ...

Effects of curing protocol and storage time on the micro-hardness of resin cements used to lute fiber-reinforced resin posts

OBJECTIVES: To determine the micro-hardness profile of two dual cure resin cements (RelyX - U100®, 3M-eSPe and Panavia F 2.0®, Kuraray) used for cementing fiberreinforced resin posts (Fibrekor® - Jeneric Pentron) under three different curing protocols and two water storage times. MATERIAL AND METHODS: Sixty 16mm long bovine incisor roots were endodontically treated and prepared for cementation of the Fibrekor posts. The cements were mixed as instructed, dispensed in the canal, the posts were seated and the curing performed as follows: a) no light activation; b) light-activation immediately after seating the post, and; c) light-activation delayed 5 minutes after seating the post. The teeth were stored in water and retrieved for analysis after 7 days and 3 months. The roots were longitudinally sectioned and the microhardness was determined at the cervical, middle and apical regions along the cement line. The data was analyzed by the three-way ANOVA test (curing mode, storage time and thirds) for each cement. The Tukey test was used for the post-hoc analysis. RESULTS: Light-activation resulted in a significant increase in the microhardness. This was more evident for the cervical region and for the Panavia cement. Storage in water for 3 months caused a reduction of the micro-hardness for both cements. The U100 cement showed less variation in the micro-hardness regardless of the curing protocol and storage time. CONCLUSIONS: The micro-hardness of the cements was affected by the curing and storage variables and were material-dependent.

Efeito do protocolo de ativação da polimerização e envelhecimento acelerado em algumas propriedades de cimentos resinosos / Effects of polymerization activation protocol and accelerated aging in some resin cements properties

Este estudo teve como objetivo avaliar os efeitos de variações no protocolo de ativação e envelhecimento acelerado em algumas propriedades de cimentos resinosos de polimerização dual. Adicionalmente, investigaram-se os efeitos da variação da temperatura ambiente e envelhecimento acelerado no tempo de trabalho e tempo de presa dos cimentos quando ativados exclusivamente pela reação química. As propriedades avaliadas foram o grau de conversão, determinado por espectrometria no infravermelho com transformada de Fourier (FTIR-ATR), microdureza Knoop, expressa em KHN, e resistência mecânica à tração expressa em MPa. Os tempos de trabalho e tempos de presa foram determinados por um reômetro oscilatório com controle de temperatura da plataforma de teste estabelecida em 24oC ou 37oC. O envelhecimento acelerado foi determinado pela armazenagem dos cimentos, em suas embalagens originais, e após os testes iniciais, em estufa a 37oC por 12 semanas.A variável de modo de ativação foi determinada em 3 níveis. Os cimentos foram manipulados de acordo com as instruções dos fabricantes e ativados por luz imediatamente (controle), ativados por luz após 10 minutos de reação química no escuro (Exp 1) ou mantidos no escuro por 15 minutos, permitindo a reação química, mas sem fotoativação (Exp 2). Os cimentos tiveram suas propriedades avaliadas em função desses diferentes modos de ativação, antes e após o envelhecimento acelerado. Cimento exclusivamente ativado pela reação química foi empregado como controle quando necessário. Os diversos resultados podem ser resumidos em alguns aspectos de interesse. O tempo de trabalho e o tempo de presa de todos cimentos foram afetados significantemente pela temperatura e envelhecimento (p<0.05). O aumento da temperatura acelerou os tempos de trabalho e presa. Os efeitos do envelhecimento foram materiaisdependentes. Alguns materiais apresentaram redução, enquanto outros apresentaram aumento dos tempos de trabalho e presa, independentemente da...

The study aimed to evaluate the effects of curing protocol and accelerated aging on some properties of dual-cure resin cements. Additionally, the effects of different ambient temperature and aging on the working and setting times were investigated when cements were self-cured only. Properties evaluated were degree of conversion as determined by FTIR-ATR spectroscopy, Knoop microhadness as expressed by KHN, and tensile strength as expressed in MPa. Working time and setting time were determined by an oscilating rheometer with controlled temperature stage at either 24oC or 37oC. Accelerated aging was performed by storing the original product kits in an oven at 37oC for 12 weeks after initial testing had been executed. Different curing protocols were established in 3 levels. Cements were manipulated according to the manufacturers instructions and light-activated immediately (control), light-activated after 10 minutes delay of self-curing in the dark (Exp 1), or simply allowed to self-cure for 15 minutes in the dark (Exp 2). Properties were evaluated according to the different curing protocol and both before and after aging. Exclusively self-curing cement was used as control product when appropriate. The results can be summarized in some aspects of interest. The working time and setting time of all products were significantly affected by temperature and aging (p<0.05). Increased temperature resulted in shorter working time and setting time. The effects of aging were material dependent. Some products presented reduced working and setting times, while others behave otherwise, regardless of the temperature. Curing mode and aging significantly affected the properties of the cements (p<0.05). In general, the degree of conversion increased with time after light-activation. The curing delay for 10 minutes caused alterations in the degree of conversion, regardless of aging, for some products, but not all. Aging affected the curing kinectics and general properties of all...

Cimentação adesiva na atualidade: revisão de literatura / Adhesive cementation nowadays: literature review

Tradicionalmente, um dos cimentos mais utilizados na cimentação de núcleos e coroas tem sido o cimento de fosfato de zinco. Outros cimentos, como os cimentos ionoméricos e os ionoméricos modificados por resina, têm sido também utilizados na cimentação de núcleos e coroas, apresentando vantagens baseadas, principalmente, na sua capacidade de adesão às estruturas dentárias, baixa solubilidade e liberação de flúor, podendo atuar na inibição do desenvolvimento de cárie. Inicialmente indicados para a cimentação de próteses adesivas, os cimentos resinosos passaram a ser indicados para a cimentação de coroas, inlays-onlays e pinos de fibra. Porém, as diferentes formulações fornecidas pelos fabricantes e o grande número de marcas comerciais disponíveis dificultam a escolha do cimento pelo clínico. As diversidades técnicas tornaram difícil o seu manuseio, o que contribuiu para as variações em seu desempenho clínico e dificulta uma análise longitudinal criteriosa. O presente artigo tem como objetivo esclarecer ao clínico as variáveis envolvidas na cimentação adesiva, bem como auxiliá-lo em suas escolhas. A relação custo-benefício da cimentação adesiva deve ser analisada com cautela, e estudos clínicos controlados devem ser conduzidos para corroborar os dados laboratoriais acerca dos prováveis resultados clínicos em longo prazo.