Effect of nanocellulose polymorphism on electrochemical analytical performance in hybrid nanocomposites with non-oxidized single-walled carbon nanotubes.

Two cellulose nanocrystals/single-walled carbon nanotube (CNC/SW) hybrids, using two cellulose polymorphs, were evaluated as electrochemical transducers: CNC type I (CNC-I/SW) and CNC type II (CNC-II/SW). They were synthesized and fully characterized, and their analytical performance as electrochemical sensors was carefully studied. In comparison with SWCNT-based and screen-printed carbon electrodes, CNC/SW sensors showed superior electroanalytical performance in terms of sensitivity and selectivity, not only in the detection of small metabolites (uric acid, dopamine, and tyrosine) but also in the detection of complex glycoproteins (alpha-1-acid glycoprotein (AGP)). More importantly, CNC-II/SW exhibited 20 times higher sensitivity than CNC-I/SW for AGP determination, yielding a LOD of 7 mg L-1.These results demonstrate the critical role played by nanocellulose polymorphism in the electrochemical performance of CNC/SW hybrid materials, opening new directions in the electrochemical sensing of these complex molecules. In general, these high-active-surface hybrids smartly exploited the preserved non-oxidized SW conductivity with the high aqueous dispersibility of the CNC, avoiding the use of organic solvents or the incorporation of toxic surfactants during their processing, making the CNC/SW hybrids promising nanomaterials for electrochemical detection following greener approaches.

Understanding the Raman enhancement of carbon nanohorns labelled with organic dyes.

Carbon nanohorns have been non-covalently functionalized with two different benzothiadiazoloquinoxalines prepared via Stille cross-coupling reactions under solvent-free conditions and microwave irradiation. The close interactions between these organic molecules and the nanostructures resulted in a prominent Raman enhancement, which makes them attractive candidates for multiple applications. A complete experimental physico-chemical characterization has been combined with in silico studies to understand these phenomena. The processability of the hybrids was exploited to prepare homogeneous films on substrates with different natures.

Preparation of Cellulose Nanocrystals: Controlling the Crystalline Type by One-Pot Acid Hydrolysis.

Cellulose nanocrystals (CNCs) have aroused increasing interest owing to their renewable origin and excellent properties derived from their size and morphology. Based on their chain orientation, CNCs can be prepared as two main allomorphs (I or II). However, achieving pure CNC allomorphs still requires enhanced control on the CNCs synthesis process and improved understanding of the involved reaction parameters. In this work, we study in detail a set of parameters for CNC synthesis using one-pot acid hydrolysis and evaluate their influence on the outcome with respect to yield, purity, and repeatability. We also demonstrate that a fast, nondestructive, and accurate methodology based on dynamic light scattering is an efficient alternative to the usual structural analysis of the synthesis outcome. Finally, we provide an improved protocol to reliably obtain each allomorph with mass yields of 25% for type I and 40% for type II. Emphasis is put on the reduction of the environmental impact and the overall preparation time.

Waterborne Graphene- and Nanocellulose-Based Inks for Functional Conductive Films and 3D Structures.

In the vast field of conductive inks, graphene-based nanomaterials, including chemical derivatives such as graphene oxide as well as carbon nanotubes, offer important advantages as per their excellent physical properties. However, inks filled with carbon nanostructures are usually based on toxic and contaminating organic solvents or surfactants, posing serious health and environmental risks. Water is the most desirable medium for any envisioned application, thus, in this context, nanocellulose, an emerging nanomaterial, enables the dispersion of carbon nanomaterials in aqueous media within a sustainable and environmentally friendly scenario. In this work, we present the development of water-based inks made of a ternary system (graphene oxide, carbon nanotubes and nanocellulose) employing an autoclave method. Upon controlling the experimental variables, low-viscosity inks, high-viscosity pastes or self-standing hydrogels can be obtained in a tailored way. The resulting inks and pastes are further processed by spray- or rod-coating technologies into conductive films, and the hydrogels can be turned into aerogels by freeze-drying. The film properties, with respect to electrical surface resistance, surface morphology and robustness, present favorable opportunities as metal-free conductive layers in liquid-phase processed electronic device structures.