Fabrication and Optimization of Nafion as a Protective Membrane for TiN-Based pH Sensors.

In this study, a solid-state modified pH sensor with RF magnetron sputtering technology was developed. The sensor consists of an active electrode consisting of a titanium nitride (TiN) film with a protective membrane of Nafion and a reference glass electrode of Ag/AgCl. The sensitivity of the pH sensor was investigated. Results show a sensor with excellent characteristics: sensitivity of 58.6 mV/pH for pH values from 2 to 12, very short response time of approximately 12 s in neutral pH solutions, and stability of less than 0.9 mV in 10 min duration. Further improvement in the performance of the TiN sensor was studied by application of a Nafion protective membrane. Nafion improves the sensor sensitivity close to Nernstian by maintaining a linear response. This paves the way to implement TiN with Nafion protection to block any interference species during real time applications in biosensing and medical diagnostic pH sensors.

Nafion Modified Titanium Nitride pH Sensor for Future Biomedical Applications.

pH sensors are increasingly being utilized in the biomedical field and have been implicated in health applications that aim to improve the monitoring and treatment of patients. In this work, a previously developed Titanium Nitride (TiN) solid-state pH sensor is further enhanced, with the potential to be used for pH regulation inside the human body and for other biomedical, industrial, and environmental applications. One of the main limitations of existing solid-state pH sensors is their reduced performance in high redox mediums. The potential shift E0 value of the previously developed TiN pH electrode in the presence of oxidizing or reducing agents is 30 mV. To minimize this redox shift, a Nafion-modified TiN electrode was developed, tested, and evaluated in various mediums. The Nafion-modified electrode has been shown to shift the E0 value by only 2 mV, providing increased accuracy in highly redox samples while maintaining acceptable reaction times. Overcoming the redox interference for pH measurement enables several advantages of the Nafion-modified TiN electrode over the standard pH glass electrode, implicating its use in medical diagnosis, real-time health monitoring, and further development of miniaturized smart sensors.

Indoor optical wireless communication system with continuous and simultaneous positioning.

The optical wireless communication (OWC) technology has been widely studied to provide high-speed communications in indoor environments. The indoor OWC-based positioning function is also highly demanded and the received signal strength (RSS) method has attracted intensive interests, where multiple transmitters are used and the positioning information is provided by estimating the channel gain from each transmitter with known location. However, this process normally requires dedicated positioning time slots, RF carriers or codewords, which limit the system data rate and throughput. To solve this limitation, in this paper we propose a filter-enhanced indoor OWC positioning scheme, where spatial waveform shaping filters are applied to the transmitters, thus enabling the signals from different transmitters to be separated via matched filters at the receiver side. Hence, this approach allows the RSS information to be obtained from the wireless communication signal directly and the positioning function realized without affecting the wireless communication data rate or throughput. In addition, since positioning is realized using the communication signal, continuous positioning can be achieved for real-time tracking. The proposed filter-enhanced positioning scheme is experimentally demonstrated in a near-infrared indoor OWC system with laser transmitters. Results show that an average positioning accuracy of 5.41 cm and 2.5 Gb/s wireless communication are achieved simultaneously. The proposed filter-enhanced positioning scheme can also be applied in visible light communication (VLC) systems with LED transmitters, and the feasibility is verified via simulations. The proposed filter-enhanced scheme provides a promising positioning method in indoor OWC systems without affecting the wireless data communication.

Sensing of Surface and Bulk Refractive Index Using Magnetophotonic Crystal with Hybrid Magneto-Optical Response.

We propose an all-dielectric magneto-photonic crystal with a hybrid magneto-optical response that allows for the simultaneous measurements of the surface and bulk refractive index of the analyzed substance. The approach is based on two different spectral features of the magneto-optical response corresponding to the resonances in p- and s-polarizations of the incident light. Angular spectra of p-polarized light have a step-like behavior near the total internal reflection angle which position is sensitive to the bulk refractive index. S-polarized light excites the TE-polarized optical Tamm surface mode localized in a submicron region near the photonic crystal surface and is sensitive to the refractive index of the near-surface analyte. We propose to measure a hybrid magneto-optical intensity modulation of p-polarized light obtained by switching the magnetic field between the transverse and polar configurations. The transversal component of the external magnetic field is responsible for the magneto-optical resonance near total internal reflection conditions, and the polar component reveals the resonance of the Tamm surface mode. Therefore, both surface- and bulk-associated features are present in the magneto-optical spectra of the p-polarized light.

Performances of the LBP Based Algorithm over CNN Models for Detecting Crops and Weeds with Similar Morphologies.

Weed invasions pose a threat to agricultural productivity. Weed recognition and detection play an important role in controlling weeds. The challenging problem of weed detection is how to discriminate between crops and weeds with a similar morphology under natural field conditions such as occlusion, varying lighting conditions, and different growth stages. In this paper, we evaluate a novel algorithm, filtered Local Binary Patterns with contour masks and coefficient k (k-FLBPCM), for discriminating between morphologically similar crops and weeds, which shows significant advantages, in both model size and accuracy, over state-of-the-art deep convolutional neural network (CNN) models such as VGG-16, VGG-19, ResNet-50 and InceptionV3. The experimental results on the "bccr-segset" dataset in the laboratory testbed setting show that the accuracy of CNN models with fine-tuned hyper-parameters is slightly higher than the k-FLBPCM method, while the accuracy of the k-FLBPCM algorithm is higher than the CNN models (except for VGG-16) for the more realistic "fieldtrip_can_weeds" dataset collected from real-world agricultural fields. However, the CNN models require a large amount of labelled samples for the training process. We conducted another experiment based on training with crop images at mature stages and testing at early stages. The k-FLBPCM method outperformed the state-of-the-art CNN models in recognizing small leaf shapes at early growth stages, with error rates an order of magnitude lower than CNN models for canola-radish (crop-weed) discrimination using a subset extracted from the "bccr-segset" dataset, and for the "mixed-plants" dataset. Moreover, the real-time weed-plant discrimination time attained with the k-FLBPCM algorithm is approximately 0.223 ms per image for the laboratory dataset and 0.346 ms per image for the field dataset, and this is an order of magnitude faster than that of CNN models.

Titanium Nitride Thin Film Based Low-Redox-Interference Potentiometric pH Sensing Electrodes.

In this work, a solid-state potentiometric pH sensor is designed by incorporating a thin film of Radio Frequency Magnetron Sputtered (RFMS) Titanium Nitride (TiN) working electrode and a commercial Ag|AgCl|KCl double junction reference electrode. The sensor shows a linear pH slope of -59.1 mV/pH, R2 = 0.9997, a hysteresis as low as 1.2 mV, and drift below 3.9 mV/hr. In addition, the redox interference performance of TiN electrodes is compared with that of Iridium Oxide (IrO2) counterparts. Experimental results show -32mV potential shift (E0 value) in 1 mM ascorbic acid (reducing agent) for TiN electrodes, and this is significantly lower than the -114 mV potential shift of IrO2 electrodes with sub-Nernstian sensitivity. These results are most encouraging and pave the way towards the development of miniaturized, cost-effective, and robust pH sensors for difficult matrices, such as wine and fresh orange juice.

High-speed indoor optical wireless communication system employing a silicon integrated photonic circuit.

Beam-steering-based optical wireless technologies are being widely investigated due to the capability of providing high-speed wireless connectivity in indoor applications. However, high-speed indoor optical wireless systems are traditionally realized with discrete bulky components, significantly limiting their practical applications. In this Letter, we demonstrate an infrared optical wireless communication system employing a miniaturized silicon integrated photonic circuit for beam steering for the first time. Experimental results show that up to 12.5 Gb/s optical wireless communication can be achieved with error-free performance over a free-space range of 140 cm, and limited mobility of users can be realized. The experimental results of this Letter open the way for realizing integrated high-speed optical wireless communications.

Indoor infrared optical wireless localization system with background light power estimation capability.

The indoor user localization function is in high demand for high-speed wireless communications, navigations and smart-home applications. The optical wireless technology has been used to localize end users in indoor environments. However, its accuracy is typically very limited, due to the ambient light, which is relatively strong. In this paper, a novel high-localization-accuracy optical wireless based indoor localization system, based on the use of the mechanism that estimates background light intensity, is proposed. Both theoretical studies and demonstration experiments are carried out. Experimental results show that the accuracy of the proposed optical wireless indoor localization system is independent on the localization light strength, and that an average localization error as small as 2.5 cm is attained, which is 80% better than the accuracy of previously reported optical wireless indoor localization systems.

RuO₂ pH Sensor with Super-Glue-Inspired Reference Electrode.

A pH-sensitive RuO₂ electrode coated in a commercial cyanoacrylate adhesive typically exhibits very low pH sensitivity, and could be paired with a RuO₂ working electrode as a differential type pH sensor. However, such sensors display poor performance in real sample matrices. A pH sensor employing a RuO₂ pH-sensitive working electrode and a SiO₂-PVB junction-modified RuO₂ reference electrode is developed as an alternative high-performance solution. This sensor exhibits a performance similar to that of a commercial glass pH sensor in some common sample matrices, particularly, an excellent pH sensitivity of 55.7 mV/pH, a hysteresis as low as 2.7 mV, and a drift below 2.2 mV/h. The developed sensor structure opens the way towards the development of a simple, cost effective, and robust pH sensor for pH analysis in various sample matrices.

Transverse magnetic field impact on waveguide modes of photonic crystals.

This Letter presents a theoretical and experimental study of waveguide modes of one-dimensional magneto-photonic crystals magnetized in the in-plane direction. It is shown that the propagation constants of the TM waveguide modes are sensitive to the transverse magnetization and the spectrum of the transverse magneto-optical Kerr effect has resonant features at mode excitation frequencies. Two types of structures are considered: a non-magnetic photonic crystal with an additional magnetic layer on top and a magneto-photonic crystal with a magnetic layer within each period. We found that the magneto-optical non-reciprocity effect is greater in the first case: it has a magnitude of δ∼10-4, while the second structure type demonstrates δ∼10-5 only, due to the higher asymmetry of the claddings of the magnetic layer. Experimental observations show resonant features in the optical and magneto-optical Kerr effect spectra. The measured dispersion properties are in good agreement with the theoretical predictions. An amplitude of light intensity modulation of up to 2.5% was observed for waveguide mode excitation within the magnetic top layer of the non-magnetic photonic crystal structure. The presented theoretical approach may be utilized for the design of magneto-optical sensors and modulators requiring pre-determined spectral features.

Demonstration of multi-wavelength tunable fiber lasers based on a digital micromirror device processor.

Based on a digital micromirror device (DMD) processor as the multi-wavelength narrow-band tunable filter, we demonstrate a multi-port tunable fiber laser through experiments. The key property of this laser is that any lasing wavelength channel from any arbitrary output port can be switched independently over the whole C-band, which is only driven by single DMD chip flexibly. All outputs display an excellent tuning capacity and high consistency in the whole C-band with a 0.02 nm linewidth, 0.055 nm wavelength tuning step, and side-mode suppression ratio greater than 60 dB. Due to the automatic power control and polarization design, the power uniformity of output lasers is less than 0.008 dB and the wavelength fluctuation is below 0.02 nm within 2 h at room temperature.

Experimental demonstration of free-space based 120 Gb/s reconfigurable card-to-card optical interconnects.

In this Letter, we propose and experimentally demonstrate a free-space based reconfigurable card-to-card optical interconnect architecture with 16-carrierless-amplitude-phase modulation. Experimental results show that up to 120 Gb/s (3×40 Gb/s) flexible interconnection can be achieved for up to 30 cm distance with a worst-case receiver sensitivity of -9.70 dBm.

High-efficiency inverted polymer solar cells controlled by the thickness of polyethylenimine ethoxylated (PEIE) interfacial layers.

In this work, we investigate the effect of the thickness of the polyethylenimine ethoxylated (PEIE) interface layer on the performance of two types of polymer solar cells based on inverted poly(3-hexylthiophene) (P3HT):phenyl C61-butryric acid methyl ester (PCBM) and thieno[3,4-b]thiophene/benzodithiophene (PTB7):[6,6]-phenyl C71-butyric acid methyl ester (PC71BM). Maximum power conversion efficiencies of 4.18% and 7.40% were achieved at a 5.02 nm thick PEIE interface layer, for the above-mentioned solar cell types, respectively. The optimized PEIE layer provides a strong enough dipole for the best charge collection while maintaining charge tunneling ability. Optical transmittance and atomic force microscopy measurements indicate that all PEIE films have the same high transmittance and smooth surface morphology, ruling out the influence of the PEIE layer on these two parameters. The measured external quantum efficiencies for the devices with thick PEIE layers are quite similar to those of the optimized devices, indicating the poor charge collection ability of thick PEIE layers. The relatively low performance of devices with a PEIE layer of thickness less than 5 nm is the result of a weak dipole and partial coverage of the PEIE layer on ITO.

Opto-VLSI-based N × M wavelength selective switch.

In this paper, we propose and experimentally demonstrate a novel N × M wavelength selective switch (WSS) architecture based on the use of an Opto-VLSI processor. Through a two-stage beamsteering process, wavelength channels from any input optical fiber port can be switched into any output optical fiber port. A proof-of-concept 2 × 3 WSS structure is developed, demonstrating flexible wavelength selective switching with an insertion loss around 15 dB.

High-speed free-space based reconfigurable card-to-card optical interconnects with broadcast capability.

In this paper, we propose and experimentally demonstrate a free-space based high-speed reconfigurable card-to-card optical interconnect architecture with broadcast capability, which is required for control functionalities and efficient parallel computing applications. Experimental results show that 10 Gb/s data can be broadcast to all receiving channels for up to 30 cm with a worst-case receiver sensitivity better than -12.20 dBm. In addition, arbitrary multicasting with the same architecture is also investigated. 10 Gb/s reconfigurable point-to-point link and multicast channels are simultaneously demonstrated with a measured receiver sensitivity power penalty of ~1.3 dB due to crosstalk.

High-speed reconfigurable card-to-card optical interconnects based on hybrid free-space and multi-mode fiber propagations.

In this paper, a high-speed reconfigurable card-to-card optical interconnect architecture based on hybrid free-space and multi-mode fiber (MMF) propagation is proposed. The use of free-space signal transmission provides flexibility and reconfigurability and the MMF extends the achievable interconnection range. A printed-circuit-board (PCB) based integrated optical interconnect module is designed and developed and proof-of-concept demonstration experiments are carried out. Results show that 3 × 10 Gb/s reconfigurable optical interconnect is realized with ~12 cm free-space propagation and a 10 m MMF length. In addition, since air turbulence due to high temperature of electronic components and heat dissipation fans always exists in typical interconnect environments and it normally results in system performance degradation, its impact on the proposed reconfigurable optical interconnect scheme is also experimentally investigated. Results indicate that even with comparatively strong air turbulence, 3 × 10 Gb/s optical interconnects with flexibility can still be achieved and the power penalty is <0.7 dB.

Optical absorption enhancement of hybrid-plasmonic-based metal-semiconductor-metal photodetector incorporating metal nanogratings and embedded metal nanoparticles.

We propose and numerically demonstrate a high absorption hybrid-plasmonic-based metal semiconductor metal photodetector (MSM-PD) comprising metal nanogratings, a subwavelength slit and amorphous silicon or germanium embedded metal nanoparticles (NPs). Simulation results show that by optimizing the metal nanograting parameters, the subwavelength slit and the embedded metal NPs, a 1.3 order of magnitude increase in electric field is attained, leading to 28-fold absorption enhancement, in comparison with conventional MSM-PD structures. This is 3.5 times better than the absorption of surface plasmon polariton (SPP) based MSM-PD structures employing metal nanogratings and a subwavelength slit. This absorption enhancement is due to the ability of the embedded metal NPs to enhance their optical absorption and scattering properties through light-stimulated resonance aided by the conduction electrons of the NPs.

Experimental demonstration of high-speed free-space reconfigurable card-to-card optical interconnects.

In this paper, we experimentally demonstrate a high-speed free-space reconfigurable card-to-card optical interconnect architecture employing MEMS-based steering mirror arrays for simple and efficient link selection. A printed-circuit-board (PCB) based interconnect module is developed and 3 × 10 Gb/s reconfigurable card-to-card optical interconnect with a bit-error-rate (BER) of ~10(-6) for up to 30 cm is realized using a 250 µm pitch-size micro-lens array. In addition, due to the usage of MEMS steering-mirrors, larger lenses can be employed at the receiver side for collecting stronger optical signal power to increase the achievable interconnect range or to improve the BER performance. Experimental results show that with 1-mm diameter lenses the interconnect distance can exceed 80 cm.

High sensitivity optically pumped quantum magnetometer.

Quantum magnetometers based on optical pumping can achieve sensitivity as high as what SQUID-based devices can attain. In this paper, we discuss the principle of operation and the optimal design of an optically pumped quantum magnetometer. The ultimate intrinsic sensitivity is calculated showing that optimal performance of the magnetometer is attained with an optical pump power of 20 µW and an operation temperature of 48°C. Results show that the ultimate intrinsic sensitivity of the quantum magnetometer that can be achieved is 327 fT/Hz(½) over a bandwidth of 26 Hz and that this sensitivity drops to 130 pT/Hz(½) in the presence of environmental noise. The quantum magnetometer is shown to be capable of detecting a sinusoidal magnetic field of amplitude as low as 15 pT oscillating at 25 Hz.

GaAs based long-wavelength microring resonator optical switches utilising bias assisted carrier-injection induced refractive index change.

We propose and analyse a GaAs-based optical switch having a ring resonator configuration which can switch optical telecommunication signals over the 1300 nm and 1500 nm bands, using bias assisted carrier injection as the switching mechanism. The switching is achieved through variation in the refractive index of the ring resonator produced by changing the injected carrier density through the application of bias voltage. Detail analysis of the switching characteristics reveals that the amount of switching depends on the refractive index change, which indeed is a strong function of injected carrier density and applied bias voltage. An isolation of 25 dB can be achieved during the ON state, while more than 40 dB isolation is realised during the OFF state. More importantly, our analysis shows that the proposed GaAs-based switch can operate over the 1300 nm and 1500 nm optical telecommunication bands, that are much farther from the bandgap of the GaAs material, without the need for "conventional" Indium based ternary and quaternary semiconductor materials. It therefore extends the usable wavelength of GaAs based optoelectronic devices. Furthermore, we have presented detail calculations to quantify power-delay metric of the proposed device. The proposed optical switch maintains a smaller footprint as when compared to Mach-Zehnder Interferometer or Directional Coupler based switches therefore, making it suitable for large scale integration and implementing next generation optical interconnects, optical communication and computing.