Analysis of the Facial Measurements and Dental Arch Dimensions for the Construction of Dental Prostheses among Adult Yemenis.

AIM: To investigate the dental arch dimension (width, length, and height) and facial measurements including inner-canthal width (ICW), bizygomatic width (BZW), inter-alar width (IAW), and mouth width (MW), and to assess the correlation between these facial measurements and dental arch width (canine width [CW], inter-first premolar width [I1PW], and inter-first molar width [I1MW]), to establish a preliminary reference for artificial teeth selection in Yemeni adult. MATERIALS AND METHODS: The study included 80 individuals (40 males and 40 females) with symmetrical faces and normal class I occlusion ranging in age from 20 to 35. Maxillary and mandibular stone casts were made for each individual. The dimensions of dental casts and facial measurements, including ICW, BZW, IAW, and MW, were assessed using a digital caliper. The collected data were analyzed by using the SPSS software program. The descriptive statistics for each measurement were made. Differences between males and females were tested using an independent-sample t-test with p-values below 0.05 considered significant. Pearson correlation coefficient between facial measurements and dental arch width was also done. RESULTS: Most dental arch dimensions and facial measurements exhibited larger mean values in the male than in the female group, with the greatest significant difference in the maxillary dental arch width and the lowest in mandibular dental arch length. A highly significant correlation is observed between ICW and maxillary canine width (CW) (r = 0.318, p = 0.004). In contrast, no significant correlation between dental arch width and BZW, IAW, and MW is shown. CONCLUSIONS: Within this study's limitations, the ICW can determine the ideal dimension of the artificial teeth in the anterior maxillary arch. While the other facial parameters, including BZW, IAW, and MW, cannot be used for artificial teeth selection in Yemeni populations. CLINICAL SIGNIFICANCE: The findings of this study established a reference database of facial measurements and their correlation to dental arch and teeth width in Yemeni populations. So, it can be implemented in artificial teeth and dental prostheses design and construction.

Mechanical and Physical Properties of Two Different Resin-based Materials: A Comparative Study.

AIM: The purpose of this study was to evaluate the degree of conversion (DC) of two different resin-based composite materials (nanofill composite and ormocer) and correlate it with some mechanical properties of these two restorative materials. MATERIALS AND METHODS: Two different resin-based materials (Filtek Supreme XT and Admira) were tested. A total of 30 samples of each type of selected composite were prepared. Specimens were immersed in distilled water for 24 hours. Then, the specimens were subjected to DC, hardness, and diametral tensile strength (DTS) measurements. The data obtained were tabulated for statistical analysis. The t-test was used to detect the significant difference among the variables tested in this study. Furthermore, the interrelationship between the studied parameters was investigated using a simple correlation coefficient statistical test. RESULTS: Statistically significant differences were observed regarding DC, hardness, and DTS. Filtek Supreme XT presented the highest values. There was a positive correlation between DC and hardness. Also there was a correlation between DC and DTS, but it was not significant. CONCLUSION: Under the tested experimental conditions, the DC of Filtek Supreme XT was higher than that of ormocer. Accordingly, Filtek Supreme XT showed better mechanical properties. CLINICAL SIGNIFICANCE: Filtek Supreme XT showed superior mechanical properties. Therefore, orthodontic bracket-based composite combinations may also be expected to perform well clinically over the lifetime of a bonded orthodontic appliance.

The effect of various mechanical and chemical surface conditioning on the bonding of orthodontic brackets to all ceramic materials.

BACKGROUND/PURPOSE: Increasing the bond strength between the orthodontic brackets and all-ceramic materials is one of the challenges facing orthodontists. The purpose of this study is to assess the shear bond strength (SBS) of metal brackets to two types of all ceramic materials using various surface mechanical and chemical conditioning methods. MATERIALS AND METHODS: Sixty ceramic blocks were prepared using two types of all ceramic materials (IPS e.max and VITA Suprinity® PC) and treated with 3 surface treatments; surface etching with 9.6% hydrofluoric acid (HFA) for 2 mins; surface roughening with Sof-Lex finishing discs; and surface roughening with Sof-Lex finishing discs and etching with HFA. Metal brackets were attached to the surface of the ceramic blocks using light cure orthodontic adhesive. Samples were subjected to 2000 thermo-cycles (5-50 °C) and the SBS was assessed using Instron machine. The adhesive remnant index (ARI) was evaluated under light microscope. Descriptive and group comparison were calculated using Two-way ANOVA, Post-hoc Tukey's and Chi-square tests and significance level set at (P < 0.05).Results: surface roughening of both ceramic materials with Sof-Lex discs and HFA resulted in a significant increase in SBS compared to other experimental groups (P < 0.05). However, VITA Suprinity ceramic prepared with Sof-Lex discs only showed the lowest SBS. The distribution of the ARI scores was significantly different between the groups (P < 0.05). CONCLUSION: Surface preparation of all ceramic materials with Sof-Lex discs and hydrofluoric acid combination produces the highest SBS to metallic orthodontic brackets.