Effect of treated zirconium dioxide nanoparticles on the flexural properties of autopolymerized resin for interim fixed restorations: An in vitro study.

STATEMENT OF PROBLEM: Fractures of interim fixed restorations are a common complication. The autopolymerized polymethyl methacrylate resin materials used for interim fixed restorations have limited mechanical properties, but whether adding treated zirconium dioxide nanoparticles improves mechanical properties is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the effect of treated zirconium dioxide nanoparticles on the flexural strength and elastic modulus of autopolymerized polymethyl methacrylate resin. MATERIAL AND METHODS: A split-metal mold (60×10×3.3 mm) was used to fabricate 40 autopolymerized acrylic resin specimens. The specimens were divided into 4 groups (n=10) according to zirconium dioxide nanoparticle concentration: control (unmodified resin) and zirconium dioxide nanoparticle contents of 1, 2.5, and 5 wt%. The specimens were mixed and polymerized according to the manufacturer's instructions and stored in distilled water for 48 ±2 hours at 37 °C. The flexural strength and elastic modulus were evaluated based on the 3-point bend test where data were analyzed by using 1-way analysis of variance and Tukey post hoc tests (α=.05). RESULTS: The flexural strength of the 1-wt% zirconium dioxide nanoparticle specimens was significantly higher than that of the control group (P<.001) but did not significantly increase further with the higher nanoparticle content (P>.05). Elastic modulus significantly decreased with 2.5-wt% zirconium dioxide nanoparticles (P=.019), while no significant changes were found with other test groups (P>.05). CONCLUSIONS: The addition of treated zirconium dioxide nanoparticles at low concentrations increased the flexural strength of autopolymerized polymethyl methacrylate resins used in fixed interim restorations.

Evaluation of two implant-supported fixed partial denture abutment designs: Influence on screw surface characteristics.

PURPOSE: To compare screw surface characteristics between hemi-engaging and non-engaging implant-supported fixed partial denture (FPD) designs after cyclic loading. MATERIALS AND METHODS: Twenty-four implants measuring 4.3 × 10 mm were mounted on acrylic resin blocks. Specimens were divided into two groups. An experimental group included twelve 3-unit FPD with a hemi-engaging design; a control group included twelve 3-unit FPDs with the conventional design of two non-engaging abutments. Both groups were subjected to two types of cycling loading (CL), first axial loading, and then lateral loading at 30°. Load was applied to the units one million times (1.0 × 106 cycles) for each loading axis. Data on screw surface roughness in three locations and screw thread depth were collected before (BL) and after (AL) each loading type. Screw surface roughness was measured in µm using a mechanical digital surface profilometer and optical profiler. To evaluate screw thread depth in µm, an upright optical microscope Axio-imager 2 was used. To confirm readings made from the optical microscope, four random samples were selected from each group for scanning electron microscopy (SEM) analysis. The effect of cyclic loading was evaluated by averaging values across the two screws within each specimen, then calculating difference scores (DL) between BL and AL (DL = AL - BL). Additional difference scores were computed between the non-engaging screws in each experimental group specimen, and one randomly selected non-engaging screw in each control specimen. This difference was referred to as the non-engaging DL. Statistical significance was assessed using Mann-Whitney U tests (α = 0.05). RESULTS: Comparisons of DL and non-engaging DL by loading type revealed one significant difference regarding surface roughness at the screw thread. Significantly greater mean changes were observed after axial loading compared to lateral loading regarding both DL (axial M = -0.36 ± 0.08; lateral M = -0.21 ± 0.09; U = 20; p = 0.003) and non-engaging DL (axial M = -0.40 ± 0.22; lateral M = -0.21 ± 0.11; U = 29; p = 0.013). No significant differences in screw surface roughness in other sites or thread depth were found between the experimental and control abutment designs in DL or in non-engaging DL. No significant differences were found for DL (axial U = 13, p = 0.423; lateral U = 9, p = 0.150;) or non-engaging DL (axial U = 13, p = 0.423; lateral U = 18, p = 1.00). CONCLUSIONS: Results suggest that overall, changes in screw surface physical characteristics did not differ between hemi-engaging and non-engaging designs after evaluating screw surface roughness and thread depth before and after axial and lateral cyclic loading.

Preload evaluation of 2 implant-supported fixed partial denture abutment designs.

STATEMENT OF PROBLEM: A hemi-engaging abutment design has been suggested to improve the stability of the implant-to-abutment interface compared with that of a fully nonengaging design to restore implant-supported fixed partial denture. However, controversy persists regarding the benefit of using a hemi-engaging abutment design and prompts the need for specific mechanical testing on the effect of these designs on screw preload under simulated clinical conditions. PURPOSE: The purpose of this in vitro study was to determine whether significant differences in preload values of the screw before and after cyclic loading exist between hemi-engaging and nonengaging abutment fixed partial denture designs. MATERIAL AND METHODS: Twenty-four conical connection implants measuring 4.3×10 mm (Nobel Biocare Replace Conical Connection; Nobel Biocare) were mounted in acrylic resin blocks. Specimens were divided into 2 groups. An experimental group included 12 three-unit fixed partial dentures with a hemi-engaging design; a control group included 12 three-unit fixed partial dentures with the conventional design of 2 nonengaging abutments. A digital screw torque meter was used to measure screw torque values per the manufacturer's recommendation of 35 Ncm. Reverse torque value was measured before cyclic loading and referred to as initial preload. After cyclic loading, reverse torque value was measured and referred to as final preload. The effect of cyclic loading was evaluated by averaging the reverse torque value across the 2 screws in each specimen and then calculating the changes between the initial preload and final preload. The difference between initial and final preload was referred to as reverse torque difference. An additional reverse torque difference, referred to as reverse torque difference-nonengaging, was calculated for the nonengaging screws in each experimental specimen and for 1 randomly selected screw of the 2 in each control specimen. Preload efficiency before and after cyclic loading was also calculated. All groups went through cyclic loading using a universal testing machine. The specimens went through axial loading first, and then the reverse torque value was measured. Twenty-four new abutment screws were then used, and the specimens then went through lateral loading at 30 degrees. Load was applied to the units (1.0×106 cycles) for each loading axis. The statistical significance of differences between the axial and lateral reverse torque difference and between the 2 groups of reverse torque difference and reverse torque difference-nonengaging were assessed using Mann-Whitney U tests (α=.05). RESULTS: A comparison of reverse torque difference between loading types revealed no significant difference (P=.773). Therefore, data for the 2 loading types were combined before comparing the reverse torque difference and reverse torque difference-nonengaging values between the 2 groups based on abutment design (12 hemi-engaging designs in the experimental group and 12 fully nonengaging designs in the control group). The experimental group mean reverse torque difference was -0.65 ±1.95 Ncm (range -4.0 to 2.4 Ncm), and the control group mean reverse torque difference was -2.5 ±5.44 Ncm (range -15.3 to 5.3 Ncm). No significant difference was found (P=.340). Furthermore, no significant difference was found between the reverse torque difference for the nonengaging screw in each of the 12 implants with a hemi-engaging design versus 1 randomly selected nonengaging screw in each of the 12 implants with a fully nonengaging design (P=.355). CONCLUSIONS: No significant difference was found in screw preload between a hemi-engaging and a full nonengaging 3-unit fixed partial denture supported by conical connection implant configurations before and after cyclic loading.

Strength and Surface Properties of a 3D-Printed Denture Base Polymer.

PURPOSE: This in vitro study evaluated the flexural strength, impact strength, hardness, and surface roughness of 3D-printed denture base resin subjected to thermal cycling treatment. MATERIALS AND METHODS: According to ISO 20795-1:2013 standards, 120 acrylic resin specimens (40/flexural strength test, 40/impact strength, and 40/surface roughness and hardness test, n = 10) were fabricated and distributed into two groups: heat-polymerized; (Major.Base.20) as control and 3D-printed (NextDent) as experimental group. Half of the specimens of each group were subjected to 10,000 thermal cycles of 5 to 55°C simulating 1 year of clinical use. Flexural strength (MPa), impact strength (KJ/m2 ), hardness (VHN), and surface roughness (µm) were measured using universal testing machine, Charpy's impact tester, Vickers hardness tester, and profilometer, respectively. Data were analyzed by ANOVA and Tukey honestly significant difference (HSD) test (α = 0.05). RESULTS: The values of flexural strength (MPa) were 86.63 ± 1.0 and 69.15 ± 0.88; impact strength (KJ/m2 )-6.32 ± 0.50 and 2.44 ± 0.31; hardness (VHN)-41.63 ± 2.03 and 34.62 ± 2.1; and surface roughness (µm)-0.18 ± 0.01 and 0.12 ± 0.02 for heat-polymerized and 3D-printed denture base materials, respectively. Significant differences in all tested properties were recorded between heat-polymerized and 3D-printed denture base materials (P < 0.001). Thermal cycling significantly lowered the flexural strength (63.93 ± 1.54 MPa), impact strength (2.40 ± 0.35 KJ/m2 ), and hardness (30.17 ± 1.38 VHN) of 3D-printed resin in comparison to thermal cycled heat-polymerized resin, but surface roughness showed non-significant difference (p = 0.262). CONCLUSION: 3D-printed resin had inferior flexural strength, impact strength, and hardness values than heat-polymerized resin, but showed superior surface roughness. Temperature changes (thermal cycling) significantly reduced the hardness and flexural strength and increased surface roughness, but did not affect the impact strength.

Effect of feldspathic porcelain layering on the marginal fit of zirconia and titanium complete-arch fixed implant-supported frameworks.

STATEMENT OF PROBLEM: Veneering with porcelain may adversely affect the marginal fit of long-span computer-aided design and computer-aided manufacturing (CAD-CAM) implant-supported fixed prostheses. Moreover, data regarding the precision of fit of CAD-CAM-fabricated implant-supported complete zirconia fixed dental prostheses (FDPs) before and after porcelain layering are limited. PURPOSE: The purpose of this in vitro study was to evaluate the effect of porcelain layering on the marginal fit of CAD-CAM-fabricated complete-arch implant-supported, screw-retained FDPs with presintered zirconia frameworks compared with titanium. MATERIAL AND METHODS: An autopolymerizing acrylic resin-fixed complete denture framework prototype was fabricated on an edentulous typodont master model (all-on-4 concept; Nobel Biocare) with 2 straight in the anterior and 2 distally tilted internal-hexagon dental implants in the posterior with multiunit abutments bilaterally in canine and first molar locations. A 3-dimensional (3D) laser scanner (S600 ARTI; Zirkonzahn) was used to digitize the prototype and the master model by using scan bodies to generate a virtual 3D CAD framework. Five presintered zirconia (ICE Zirkon Translucent - 95H16; Zirkonzahn) and 5 titanium (Titan 5 - 95H14; Zirkonzahn) frameworks were fabricated using the CAM milling unit (M1 Wet Heavy Metal Milling Unit; Zirkonzahn).The 1-screw test was applied by fixing the frameworks at the location of the maxillary left first molar abutment, and an industrial computed tomography (CT) scanner (XT H 225 - Basic Configuration; Nikon) was used to scan the framework-model complex to evaluate the passive fit of the frameworks on the master model. The scanned data were transported in standard tessellation language (STL) from Volume Graphics analysis software to PolyWorks analysis software by using the maximum-fit algorithm to fit scanned planes in order to mimic the mating surfaces in the best way. 3D virtual assessment of the marginal fit was performed at the abutment-framework interface at the maxillary right canine (gap 3) and right first molar (gap 4) abutments without prosthetic screws. The facial or buccal aspects of the teeth on frameworks were layered with corresponding porcelain (Initial Dental Ceramic System; GC) and CT-scanned again using the same protocol. Marginal fit measurements were made for 4 groups: titanium (Ti) (control), porcelain-layered titanium (Ti-P) (control), zirconia (Zir), and porcelain-layered zirconia (Zir-P). 3D discrepancy mean values were computed and calculated, and the results were analyzed with a repeated measures 3-way ANOVA using the maximum likelihood estimation method and Bonferroni adjustments for selected pairwise comparison t-tests (α=.05). RESULTS: The 3D fit was measured at gap 3 and gap 4. Statistically significant differences in mean 3D discrepancies were observed between Zir-P (175 µm) and Zir (89 µm) and between Zir-P and Ti-P (71 µm) (P<.001). CONCLUSIONS: Porcelain layering had a significant effect on the marginal fit of CAD-CAM-fabricated complete-arch implant-supported, screw-retained FDPs with partially sintered zirconia frameworks. 3D marginal discrepancy mean values for all groups were within clinically acceptable limits (<120 µm), except for the layered zirconia framework.

A load-to-fracture and strain analysis of monolithic zirconia cantilevered frameworks.

STATEMENT OF PROBLEM: The dimensions of implant-supported fixed cantilevered prostheses are important to prevent mechanical and biological complications. Information on the optimum thickness and cantilever length for improving the strength of zirconia cantilevered frameworks is limited in the literature. PURPOSE: The purpose of this in vitro study was to investigate the effect of cantilever length and occlusocervical thickness on the load-to-fracture and strain distribution of zirconia frameworks. MATERIAL AND METHODS: Twenty-seven rectangular prism-shaped specimens (6 mm thick buccolingually) were fabricated using a computer-aided design and computer-aided manufacturing (CAD-CAM) milling technique. The specimens were prepared in 9 groups (n=3) according to their vertical dimensions (6×6 mm, 8×6 mm, and 10×6 mm) and cantilever loading distance (7 mm, 10 mm, and 17 mm). All specimens were heat treated in a porcelain furnace and thermocycled for 20000 cycles before the tests. Each framework was secured using a clamp attached to the first 20 mm of the framework. A 3-dimensional image correlation technique was used for a full-field measurement of strain during testing. A load-to-fracture test was used until the specimens fractured. Maximum force and principal strain data were analyzed by 2-way analysis of variance using the maximum likelihood estimation method (α=.05). RESULTS: No statistically significant effects (P>.05) were found for occlusocervical thickness and cantilever length or between them on the strain distribution. The results showed that the effect of occlusocervical thickness and cantilever length was significant on the load to fracture (P<.001). No statistically significant interaction was observed between the 2 factors (P>.05). CONCLUSIONS: Increased occlusocervical thickness and decreased cantilever length allowed the cantilever to withstand higher loads. The occlusocervical thicknesses and cantilever lengths of zirconia frameworks tested withstood the maximum reported occlusal force. The properties of components in the implant-abutment framework assembly should be considered in the interpretation of these results.

Influence of Denture Cleansers on the Retention Loss of Attachment Systems Retained Implant Overdenture.

Background: This study aimed to evaluate the effects of different denture cleansing solutions (DCSs) on the retention of Locator and Locator R-Tx attachment systems of implant retained overdentures (IRO). Methods: Two part acrylic resin blocks were fabricated, upper part contained metal housing and plastic inserts and lower part contained implant analogs and abutments. Eighty pink plastic inserts (40/attachment, 10/solution) were immersed in Corega, Fittydent, sodium hypochlorite, and water for a time simulating upto 1-year of clinical usage. Acrylic blocks were held on a universal testing machine for a pull-out test to record the dislodgement force. Measurements were conducted after 6 months (T1) and 12 months (T2). One-way ANOVA followed by Tukey's HSD test was used to analyze the results (α = 0.05). Results: For both attachments, retention significantly decreased after immersion in different solutions at T2 (P < 0.001). Locator R-Tx attachment in NaOCl showed a significant decrease in retention compared with other solutions at T1. At T2, there was a significant decrease in retention for all DCS compared with water (P < 0.001). Locator R-TX showed higher retention values per solution compared to Locator attachment (P < 0.001). In terms of retention loss %, NaOCl recorded the highest (61.87%) loss, followed by Corega (55.54%) and Fittydent (43.13%), whereas water demonstrated the best retention (16.13%) in both groups. Conclusion: Locator R-TX has better retention with different DCS immersion. The loss of retention varied with different types of DCS and NaOCl recorded the highest retention loss. Therefore, denture cleanser selection must be guided by the type of IRO attachment.

Influence of Propolis Extract (Caffeic Acid Phenethyl Ester) Addition on the Candida albicans Adhesion and Surface Properties of Autopolymerized Acrylic Resin.

Background: Denture stomatitis has been linked to the adhesion and proliferation of Candida albicans (C. albicans) on denture bases, which is a common and recurrent problem in denture wearers. The current study aimed to evaluate the effect of incorporating caffeic acid phenethyl ester (CAPE) into autopolymerized polymethyl methacrylate (PMMA) acrylic resin on C. albicans adhesion, surface roughness, and hardness as well as the correlation between tested properties. Methods: Autopolymerized acrylic resin discs (N = 100, 50/C. albicans adhesion; 50/C. albicans surface roughness and hardness test) were fabricated in dimensions 15 × 2.5 mm, samples were categorized into 5 groups (n = 10) based on CAPE concentrations; unmodified (control), 2.5, 5, 10 and 15% wt of acrylic powder. Specimens were stored in distilled water for 48 h at 37°C. C. albicans adhesion was evaluated via direct culture method. Profilometer and Vickers hardness tester were used for surface roughness and hardness measurement. Post hoc Tukey's HSD with ANOVA test was performed to compare the difference of means amongst groups. P values were statistically significant at ≤0.05. Results: The addition of 2.5% of CAPE to PMMA has significantly reduced C. albicans counts in comparison to higher CAPE concentrations (p < 0.001). As for surface roughness, it was noticed that it increased with increased CAPE concentrations (p < 0.0001). While surface hardness decreased as CAPE concentrations increased (p < 0.0001). All tested properties showed a significant difference amongst groups for C. albicans colony count and surface parameters. Conclusion: The addition of 2.5% of CAPE to PMMA acrylic resin significantly decreased C. albicans count compared to higher CAPE concentrations. CAPE can be used as an adjunct in the prevention of DS by incorporating in the PMMA acrylic resin.

Water Sorption, Solubility, and Translucency of 3D-Printed Denture Base Resins.

This study aimed to evaluate the water sorption, solubility, and translucency of 3D-printed denture base resins (NextDent, FormLabs, and Asiga), compare them to heat-polymerized acrylic denture base resins, and assess their performance under the effects of thermal cycling. A total of 80 acrylic disc specimens were used in the current study, categorized into four groups (n = 10); in one group, the samples were fabricated conventionally with a heat-polymerizing process (control), while the other three groups were fabricated digitally from different 3D-printed reins (NextDent, FormLabs, and Asiga). Specimens were fabricated according to the manufacturers' recommendations and immersed in distilled water for 48 h at 37 °C. Data on water sorption, solubility, and translucency measurements (T1) were obtained. All the specimens were subjected to 5000 thermal cycles, and then the measures were repeated using the same method (T2). Data analysis was attained via ANOVA and the post hoc Tukey test (α = 0.05). The type of resin significantly affected the values of water sorption, solubility, and translucency (p < 0.001). The water sorption of 3D-printed resins was increased significantly in comparison to control with or without a thermal cycling effect. In terms of solubility, a significant increase in 3D-printed resins before thermocycling was observed; however, after thermocycling, Asiga had a significantly low value compared to the other groups (p < 0.001). Thermal cycling increased the water sorption and solubility of all tested materials. In comparison to control, the translucency of the 3D-printed resins was significantly decreased (p < 0.001). The translucency was significantly decreased per material in terms of the thermal cycling effect (before and after). NextDent showed significantly low translucency values (p < 0.001) compared to the other groups. All 3D-printed resin groups had higher water sorption and solubility and lower translucency values in comparison to the heat-polymerized resin group. Regardless of resin types, thermal cycling adversely affected all tested properties.

An Updated Review of Salivary pH Effects on Polymethyl Methacrylate (PMMA)-Based Removable Dental Prostheses.

Salivary pH is a neglected factor that may affect the performance of removable dental prostheses (RDP). This study aimed to review literature in reference to the role of salivary pH on the performance of RDP and materials used for their fabrication. From January 1990 until December 2021, a search was done on PubMed, Scopus, and Web of Science databases using removable dental prostheses, salivary pH, PMMA, Denture base, and physical properties as keywords. Articles that met the inclusion criteria (full-length articles have investigated the effect of salivary pH on RDP materials in vitro and in vivo) were included. Out of 433 articles, 8 articles that met the inclusion criteria were included. All studies used artificial saliva with different salivary pH ranging between 3 and 14. Two articles investigated the role of salivary pH on the cytotoxicity of denture base resins and soft liner. One article studied the durability and retention of attachments, one article analyzed the performance of PEEK materials, one article researched the fatigue resistance of a denture base, one article investigated the corrosion of RPD framework cast and milled Co-Cr, one article studied the strength and clasp retention and deformation of acetal and PEEK materials, and one evaluated changes in mass and surface morphology of CAD-CAM fiber-reinforced composites for the prosthetic framework. Different salivary pH affected all included materials in this review except PEEK materials. The most adverse effect was reported with alkaline and acidic; however, the acidic showed the most deterioration effect. Salivary pH has a role in the selection of material used for RDP fabrication.

Impact of Polymerization Technique and ZrO2 Nanoparticle Addition on the Fracture Load of Interim Implant-Supported Fixed Cantilevered Prostheses in Comparison to CAD/CAM Material.

ZrO2 nanoparticles (ZNPs) have excellent physical properties. This study investigated the fracture load of implant-supported, fixed cantilevered prosthesis materials, reinforced with ZNPs and various polymerization techniques, compared with conventional and CAD/CAM materials. Sixty specimens were made from two CAD/CAM; milled (MIL) (Ceramill TEMP); and 3D-printed (NextDent Denture 3D+). Conventional heat-polymerized acrylic resin was used to fabricate the other specimens, which were grouped according to their polymerization technique: conventionally (HP) and autoclave-polymerized (AP); conventionally cured and reinforced with 5 wt% ZNPs (HPZNP); and autoclave reinforced with 5 wt% ZNPs (APZNP). The specimens were thermocycled (5000 cycles/30 s dwell time). Each specimen was subjected to static vertical loading (1 mm/min) using a universal Instron testing machine until fracture. Scanning electron microscopy was used for fracture surface analyses. The ANOVA showed significant fracture load differences between all the tested groups (p = 0.001). The Tukey post hoc tests indicated a significant difference in fracture load between all tested groups (p ˂ 0.001) except HP vs. HPZNP and AP vs. MIL. APZNP had the lowest mean fracture load value (380.7 ± 52.8 N), while MIL had the highest (926.6 ± 82.8 N). The CAD/CAM materials exhibited the highest fracture load values, indicating that they could be used in long-term interim prostheses. Autoclave polymerization improved fracture load performance, whereas ZrO2 nanoparticles decreased the fracture load performance of cantilevered prostheses.

In Vitro Assessment of Artificial Aging on the Antifungal Activity of PMMA Denture Base Material Modified with ZrO2 Nanoparticles.

The antifungal effect of zirconium dioxide nanoparticles (ZrO2NPs) incorporated into denture base material has been inadequately investigated; additionally, to the authors' knowledge, no studies have assessed the influence of artificial aging on the antifungal activity of these particles. Methodology. Heat-polymerized acrylic resin disks were fabricated and divided into four groups (0%, 1%, 2.5%, and 5% ZrO2NPs by weight). Antifungal activity was assessed using the direct culture and disk diffusion methods. Surface roughness and contact angles were measured using a profilometer and a goniometer, respectively. The artificial aging procedure was performed by repeating all tests at 7, 14, and 30 days following 2 rounds of thermocycling. Data were analyzed using ANOVA and Tukey's post-hoc test (p < 0.05). Results. The addition of ZrO2NPs significantly decreased the adhesion of Candida albicans with and without artificial aging procedures (p < 0.001), while the disk diffusion methods did not reveal inhibition zones. ZrO2NP-modified specimens displayed significantly higher surface roughness compared to specimens in the control group (p < 0.05) and showed the same behaviors with artificial aging procedures. The contact angle was significantly decreased in all modified groups in comparison to the control group (p < 0.05). Conclusion. The addition of ZrO2NPs to polymethylmethacrylate denture base material reduced the adhesion of Candida albicans with a long-term antifungal effect. With the addition of ZrO2NPs, contact angles were decreased and surface roughness was increased; 1% was the most appropriate concentration. Clinical significance. The addition of ZrO2NPs to denture base material confers a long-term antifungal effect and could be used as a possible method for preventing and treating denture stomatitis.

Peri-implant Sulcular Fluid Galectin-1, Soluble Urokinase Plasminogen Activator Receptor and IL-1ß Levels under Peri-implant Inflammatory Conditions.

PURPOSE: Soluble urokinase plasminogen activator receptor (suPAR) and interleukin 1-beta (IL-1ß) are inflammatory biomarkers, whereas galectin-1 is an anti-inflammatory cytokine. The relationship between suPAR, galactin-1 and IL-1ß levels in peri-implant sulcular fluid (PISF) in relation to dental implants remains unaddressed. The aim was to assess suPAR, galectin-1, and IL-1ß levels in PISF under peri-implant inflammatory conditions. MATERIALS AND METHODS: Demographic data and information related to jaw location and duration of implants in function as well as systemic health was retrieved from patients' dental records. Peri-implant plaque and gingival indices (PI and GI, respectively), probing depth (PD) and crestal bone loss (CBL) were recorded. The PISF was collected and levels of suPAR, galectin-1 and IL-1ß were determined using standard techniques. Sample-size estimation and statistical analyses were done. Correlation of suPAR and galectin-1 with IL-1ß were assessed via logistic regression. p-values < 0.05 were considered statistically significant. RESULTS: Seventy-two patients (45 males and 27 females) with peri-implant diseases were included. Thirty-six patients (22 males and 14 females) had peri-implant mucositis; 36 (23 males and 13 females) had healthy peri-implant tissues. The PISF volume was statistically significantly higher among patients with (0.52 ± 0.05 µl) than without peri-implant diseases (0.06 ± 0.01 µl) (p < 0.001). The PISF levels of suPAR (p < 0.01), galectin-1 (p < 0.01) and IL-1ß (p < 0.01) were statistically significantly higher among patients with than without peri-implant diseases. In patients with peri-implant mucositis, PISF suPAR (p < 0.001) and galectin-1 (p < 0.001) levels correlated with PISF IL-1ß levels. In patients with peri-implant mucositis, increasing peri-implant PD and IL-1ß levels directly correlated with increased PISF suPAR (p < 0.001) and galectin-1 (p < 0.05) levels. CONCLUSION: Increased PISF levels of suPAR, galectin and IL-1ß suggest that these proteins possibly contribute towards the pathogenesis of peri-implant inflammation, and are potential biomarkers of peri-implant diseases.

Influence of Different Conditioning Treatments on the Bond Integrity of Root Dentin to rGO Infiltrated Dentin Adhesive. SEM, EDX, FTIR and MicroRaman Study.

The present study aimed to synthesize and equate the mechanical properties and dentin interaction of two adhesives; experimental adhesive (EA) and 5 wt.% reduced graphene oxide rGO) containing adhesive. Scanning electron microscopy (SEM)-Energy-dispersive X-ray spectroscopy (EDX), Micro-Raman spectroscopy, push-out bond strength test, and Fourier Transform Infrared (FTIR) spectroscopy were employed to study nano-bond strength, degree of conversion (DC), and adhesive-dentin interaction. The EA was prepared, and rGO particles were added to produce two adhesive groups, EA-rGO-0% (control) and rGO-5%. The canals of sixty roots were shaped and prepared, and fiber posts were cemented. The specimens were further alienated into groups based on the root canal disinfection technique, including 2.5% sodium hypochlorite (NaOCl), Photodynamic therapy (PDT), and ER-CR-YSGG laser (ECYL). The rGO nanoparticles were flake-shaped, and EDX confirmed the presence of carbon (C). Micro-Raman spectroscopy revealed distinct peaks for graphene. Push-out bond strength test demonstrated highest values for the EA-rGO-0% group after NaOCl and PDT conditioning whereas, rGO-5% showed higher values after ECYL conditioning. EA-rGO-0% presented greater DC than rGO-5% adhesive. The rGO-5% adhesive demonstrated comparable push-out bond strength and rheological properties to the controls. The rGO-5% demonstrated acceptable DC (although lower than control group), appropriate dentin interaction, and resin tag establishment.

Disinfection of acrylic denture resin polymer with Rose Bengal, Methylene blue and Porphyrin derivative in photodynamic therapy.

AIM: The study aimed to assess the effect of in-vitro chlorhexidine and antimicrobial photodynamic therapy (aPDT) disinfection protocols against acrylic resin specimens colonized with S. mutans, S. aureus, E. coli, and C. albicans. MATERIAL AND METHODS: Reference strains of S. mutans, S. aureus, E. coli, and C. albicans were tested. Sixteen blocks of acrylic specimens were prepared by heat-cure acrylic resin and contaminated by in-vitro biofilm growth. Specimens in group 1, group 2 and group 3 were treated with Rose Bengal (RB), methylene blue (MB) 500 mg/L and porphyrin derivative (PD) 5 ml respectively, for the sensitization of biofilms. All photosensitizers (PS) were activated by LED at different wavelength. CHX was prepared in sterile distilled water and applied for 60 s. Each contaminated specimen was sprayed on all its surfaces with the aforementioned photosensitizers and control CHX. One-way analysis of variance (ANOVA) model was used to test the effect of the treatments and Tukey multiple comparison tests to compare means OF CFU/mL (log10) for exposed E. coli, C. albicans, S aureus, and S. mutans RESULTS: Specimens treated with 0.12% CHX (control) demonstrated a significant reduction in CFU/mL (log10) for exposed E. coli; 2.04±0.07 CFU/mL, C. albicans; 2.09±0.85 CFU/mL, S aureus; 3.04±0.11 CFU/mL, and S. mutans; 2.54±0.91 CFU/mL. The intragroup comparison revealed E.coli did not exhibit a decrease in reduction CFU/mL (log10) when acrylic resin irradiated with RB 5 µm. Whereas, CFU/mL (log10) values of S.aureus; 3.62±0.68 and S.mutans; 3.41±0.13 plummeted (p<0.05). Intergroup comparison showed E.coli values to display comparable reduction when disinfected with MB 500 mg/L and 0.12% CHX; 3.16±0.34 and 2.04±0.07 CFU/mL (log10) (p<0.05). CONCLUSION: Photosensitizers (RB, MB, PD) are selective in reducing bacterial count on acrylic resin blocks. CHX was found to be effective against all bacteria E.coli, C.albicans, S.aureus, and S.mutans at a concentration of 0.12%.

Esthetic smile rehabilitation of enamel hypomineralized teeth with E-max prosthesis: Case report.

Developmental enamel hypomineralization is a condition affect quality of enamel result in low translucency and opacity area that compromise patient smile. Lithium disilicate Emax prosthesis report a superior properties in esthetic treatment. This report is aimed to determine the effectiveness of lithium disilicate (E-max) prosthesis in managing esthetic demand of patient with enamel hypomineralized teeth.

Multidisciplinary approach with predictable esthetics: A case report.

This case report explains an effective multidisciplinary approach used to improve the function, biology, and esthetic of a patient presented with an excessive gingival display, a spacing between anterior teeth, small size anterior teeth in maxilla and mandible. Also, unrestorable molars were noted with multiple carious lesions. The treatment combined crown lengthening, prosthetic dentistry using lithium disilicate crowns and minimally invasive implants placement approach.