Structure- and Electrolyte-Sensitivity in CO2 Electroreduction.

The utilization of fossil fuels (i.e., coal, petroleum, and natural gas) as the main energy source gives rise to serious environmental issues, including global warming caused by the continuously increasing level of atmospheric CO2. To deal with this challenge, fossil fuels are being partially replaced by renewable energy such as solar and wind. However, such energy sources are usually intermittent and currently constitute a very low portion of the overall energy consumption. Recently, the electrochemical conversion of CO2 to chemicals and fuels with high energy density driven by electricity derived from renewable energy has been recognized as a promising strategy toward sustainable energy. The activation and reduction of CO2, which is a thermodynamically stable and kinetically inert molecule, is extremely challenging. Although the participation of protons in the CO2 electroreduction reaction (CO2RR) helps lower the energy barrier, high overpotentials are still needed to efficiently drive the process. On the other hand, the concurrent hydrogen evolution reaction (HER) under CO2RR conditions leads to lower selectivity toward CO2RR products. Electrocatalysts that are highly active and selective for multicarbon products are urgently needed to improve the energy efficiency of CO2RR. The reduction of CO2 involves multiple proton-electron transfers and has many complex intermediates. Recent reports have shown that the relative stability of the intermediates on the surface of catalysts determines final reaction pathways as well as the product selectivity. Furthermore, this reaction displays a strong structure-sensitivity. The atomic arrangement, electronic structure, chemical composition, and oxidation state of the catalysts significantly influence catalyst performance. Fundamental understanding of the dependence of the reaction mechanisms on the catalyst structure would guide the rational design of new nanostructured CO2RR catalysts. As a reaction proceeding in a complex environment containing gas/liquid/solid interfaces, CO2RR is also intensively affected by the electrolyte. The electrolyte composition in the near surface region of the electrode where the reaction takes place plays a vital role in the reactivity. However, the former might also be indirectly determined by the bulk electrolyte composition via diffusion. Adding to the complexity, the structure, chemical state and surface composition of the catalysts under reaction conditions usually undergo dynamic changes, especially when adsorbed ions are considered. Therefore, in addition to tuning the structure of the electrocatalysts, being able to also modify the electrolyte provides an alternative method to tune the activity and selectivity of CO2RR. In situ and operando characterization methods must be employed to gain in depth understanding on the structure- and electrolyte-sensitivity of real CO2RR catalysts under working conditions. This Account provides examples of recent advances in the development of nanostructured catalysts and mechanistic understanding of CO2RR. It discusses how the structure of a catalyst (crystal orientation, oxidation state, atomic arrangement, defects, size, surface composition, segregation, etc.) influences the activity and selectivity, and how the electrolyte also plays a determining role in the reaction activity and selectivity. Finally, the importance of in situ and operando characterization methods to understand the structure- and electrolyte-sensitivity of the CO2RR is discussed.

Ab Initio Cyclic Voltammetry on Cu(111), Cu(100) and Cu(110) in Acidic, Neutral and Alkaline Solutions.

Electrochemical reactions depend on the electrochemical interface between the electrode surfaces and the electrolytes. To control and advance electrochemical reactions there is a need to develop realistic simulation models of the electrochemical interface to understand the interface from an atomistic point-of-view. Here we present a method for obtaining thermodynamic realistic interface structures, a procedure we use to derive specific coverages and to obtain ab initio simulated cyclic voltammograms. As a case study, the method and procedure is applied in a matrix study of three Cu facets in three different electrolytes. The results have been validated by direct comparison to experimental cyclic voltammograms. The alkaline (NaOH) cyclic voltammograms are described by H* and OH*, while in neutral medium (KHCO3 ) the CO 3* species are dominating and in acidic (KCl) the Cl* species prevail. An almost one-to-one mapping is observed from simulation to experiments giving an atomistic understanding of the interface structure of the Cu facets. Atomistic understanding of the interface at relevant eletrolyte conditions will further allow realistic modelling of electrochemical reactions of importance for future eletrocatalytic studies.

Selective CO2 Electroreduction to Ethylene and Multicarbon Alcohols via Electrolyte-Driven Nanostructuring.

Production of multicarbon products (C2+ ) from CO2 electroreduction reaction (CO2 RR) is highly desirable for storing renewable energy and reducing carbon emission. The electrochemical synthesis of CO2 RR catalysts that are highly selective for C2+ products via electrolyte-driven nanostructuring is presented. Nanostructured Cu catalysts synthesized in the presence of specific anions selectively convert CO2 into ethylene and multicarbon alcohols in aqueous 0.1 m KHCO3 solution, with the iodine-modified catalyst displaying the highest Faradaic efficiency of 80 % and a partial geometric current density of ca. 31.2 mA cm-2 for C2+ products at -0.9 V vs. RHE. Operando X-ray absorption spectroscopy and quasi in situ X-ray photoelectron spectroscopy measurements revealed that the high C2+ selectivity of these nanostructured Cu catalysts can be attributed to the highly roughened surface morphology induced by the synthesis, presence of subsurface oxygen and Cu+ species, and the adsorbed halides.

Pt-Richcore/Sn-Richsubsurface/Ptskin Nanocubes As Highly Active and Stable Electrocatalysts for the Ethanol Oxidation Reaction.

Direct ethanol fuel cells are one of the most promising electrochemical energy conversion devices for portable, mobile and stationary power applications. However, more efficient and stable and less expensive electrocatalysts are still required. Interestingly, the electrochemical performance of the electrocatalysts toward the ethanol oxidation reaction can be remarkably enhanced by exploiting the benefits of structural and compositional sensitivity and control. Here, we describe the synthesis, characterization, and electrochemical behavior of cubic Pt-Sn nanoparticles. The electrochemical activity of the cubic Pt-Sn nanoparticles was found to be about three times higher than that obtained with unshaped Pt-Sn nanoparticles and six times higher than that of Pt nanocubes. In addition, stability tests indicated the electrocatalyst preserves its morphology and remains well-dispersed on the carbon support after 5000 potential cycles, while a cubic (pure) Pt catalyst exhibited severe agglomeration of the nanoparticles after a similar stability testing protocol. A detailed analysis of the elemental distribution in the nanoparticles by STEM-EELS indicated that Sn dissolves from the outer part of the shell after potential cycling, forming a ∼0.5 nm Pt skin. This particular atomic composition profile having a Pt-rich core, a Sn-rich subsurface layer, and a Pt-skin surface structure is responsible for the high activity and stability.

Elemental Anisotropic Growth and Atomic-Scale Structure of Shape-Controlled Octahedral Pt-Ni-Co Alloy Nanocatalysts.

Multimetallic shape-controlled nanoparticles offer great opportunities to tune the activity, selectivity, and stability of electrocatalytic surface reactions. However, in many cases, our synthetic control over particle size, composition, and shape is limited requiring trial and error. Deeper atomic-scale insight in the particle formation process would enable more rational syntheses. Here we exemplify this using a family of trimetallic PtNiCo nanooctahedra obtained via a low-temperature, surfactant-free solvothermal synthesis. We analyze the competition between Ni and Co precursors under coreduction "one-step" conditions when the Ni reduction rates prevailed. To tune the Co reduction rate and final content, we develop a "two-step" route and track the evolution of the composition and morphology of the particles at the atomic scale. To achieve this, scanning transmission electron microscopy and energy dispersive X-ray elemental mapping techniques are used. We provide evidence of a heterogeneous element distribution caused by element-specific anisotropic growth and create octahedral nanoparticles with tailored atomic composition like Pt1.5M, PtM, and PtM1.5 (M = Ni + Co). These trimetallic electrocatalysts have been tested toward the oxygen reduction reaction (ORR), showing a greatly enhanced mass activity related to commercial Pt/C and less activity loss than binary PtNi and PtCo after 4000 potential cycles.

Identical Location Transmission Electron Microscopy Imaging of Site-Selective Pt Nanocatalysts: Electrochemical Activation and Surface Disordering.

We have employed identical location transmission electron microscopy (IL-TEM) to study changes in the shape and morphology of faceted Pt nanoparticles as a result of electrochemical cycling; a procedure typically employed for activating platinum surfaces. We find that the shape and morphology of the as-prepared hexagonal nanoparticles are rapidly degraded as a result of potential cycling up to +1.3 V. As few as 25 potential cycles are sufficient to cause significant degradation, and after about 500-1000 cycles the particles are dramatically degraded. We also see clear evidence of particle migration during potential cycling. These finding suggest that great care must be exercised in the use and study of shaped Pt nanoparticles (and related systems) as electrocatlysts, especially for the oxygen reduction reaction where high positive potentials are typically employed.

Shape-dependent electrocatalysis: formic acid electrooxidation on cubic Pd nanoparticles.

The electrocatalytic properties of palladium nanocubes towards the electrochemical oxidation of formic acid were studied in H(2)SO(4) and HClO(4) solutions and compared with those of spherical Pd nanoparticles. The spherical and cubic Pd nanoparticles were characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The intrinsic electrocatalytic properties of both nanoparticles were shown to be strongly dependent on the amount of metal deposited on the gold substrate. Thus, to properly compare the activity of both systems (spheres and nanocubes), the amount of sample has to be optimized to avoid problems due to a lower diffusion flux of reactants in the internal parts of the catalyst layer resulting in a lower apparent activity. Under the optimized conditions, the activity of the spheres and nanocubes was very similar between 0.1 and 0.35 V. From this potential value, the activity of the Pd nanocubes was remarkably higher. This enhanced electrocatalytic activity was attributed to the prevalence of Pd(100) facets in agreement with previous studies with Pd single crystal electrodes. The effect of HSO(4)(-)/SO(4)(2-) desorption-adsorption was also evaluated. The activity found in HClO(4) was significantly higher than that obtained in H(2)SO(4) in the whole potential range.

Development of a single crystal sample holder for interfacing ultrahigh vacuum and electrochemical experimentation.

Electrocatalyst surfaces prepared under ultrahigh vacuum (UHV) conditions can create model surfaces to better connect theoretical calculations with experimental studies. The development of a single crystal sample holder and inert electrochemical cells prepared with modularity and chemical stability in mind would allow for expensive single crystals to be reused indefinitely in both UHV and electrochemical settings. This sample holder shows reproducible surface preparations for single crystal samples and consistent electrochemical experiments without the introduction of impurities into the surface. The presented setup has been used as a critical piece for the characterization of Cu(111) surfaces under CO2 electrochemical reduction reaction conditions as a test case.

Imaging electrochemically synthesized Cu2O cubes and their morphological evolution under conditions relevant to CO2 electroreduction.

Copper is a widely studied catalyst material for the electrochemical conversion of carbon dioxide to valuable hydrocarbons. In particular, copper-based nanostructures expressing predominantly {100} facets have shown high selectivity toward ethylene formation, a desired reaction product. However, the stability of such tailored nanostructures under reaction conditions remains poorly understood. Here, using liquid cell transmission electron microscopy, we show the formation of cubic copper oxide particles from copper sulfate solutions during direct electrochemical synthesis and their subsequent morphological evolution in a carbon dioxide-saturated 0.1 M potassium bicarbonate solution under a reductive potential. Shape-selected synthesis of copper oxide cubes was achieved through: (1) the addition of chloride ions and (2) alternating the potentials within a narrow window where the deposited non-cubic particles dissolve, but cubic ones do not. Our results indicate that copper oxide cubes change their morphology rapidly under carbon dioxide electroreduction-relevant conditions, leading to an extensive re-structuring of the working electrode surface.

Enhanced Formic Acid Oxidation over SnO2-decorated Pd Nanocubes.

The formic acid oxidation reaction (FAOR) is one of the key reactions that can be used at the anode of low-temperature liquid fuel cells. To allow the knowledge-driven development of improved catalysts, it is necessary to deeply understand the fundamental aspects of the FAOR, which can be ideally achieved by investigating highly active model catalysts. Here, we studied SnO2-decorated Pd nanocubes (NCs) exhibiting excellent electrocatalytic performance for formic acid oxidation in acidic medium with a SnO2 promotion that boosts the catalytic activity by a factor of 5.8, compared to pure Pd NCs, exhibiting values of 2.46 A mg-1 Pd for SnO2@Pd NCs versus 0.42 A mg-1 Pd for the Pd NCs and a 100 mV lower peak potential. By using ex situ, quasi in situ, and operando spectroscopic and microscopic methods (namely, transmission electron microscopy, X-ray photoelectron spectroscopy, and X-ray absorption fine-structure spectroscopy), we identified that the initially well-defined SnO2-decorated Pd nanocubes maintain their structure and composition throughout FAOR. In situ Fourier-transformed infrared spectroscopy revealed a weaker CO adsorption site in the case of the SnO2-decorated Pd NCs, compared to the monometallic Pd NCs, enabling a bifunctional reaction mechanism. Therein, SnO2 provides oxygen species to the Pd surface at low overpotentials, promoting the oxidation of the poisoning CO intermediate and, thus, improving the catalytic performance of Pd. Our SnO x -decorated Pd nanocubes allowed deeper insight into the mechanism of FAOR and hold promise for possible applications in direct formic acid fuel cells.