Thermal interface materials with graphene fillers: review of the state of the art and outlook for future applications.

We review the current state-of-the-art graphene-enhanced thermal interface materials for the management of heat in the next generation of electronics. Increased integration densities, speed and power of electronic and optoelectronic devices require thermal interface materials with substantially higher thermal conductivity, improved reliability, and lower cost. Graphene has emerged as a promising filler material that can meet the demands of future high-speed and high-powered electronics. This review describes the use of graphene as a filler in curing and non-curing polymer matrices. Special attention is given to strategies for achieving the thermal percolation threshold with its corresponding characteristic increase in the overall thermal conductivity. Many applications require high thermal conductivity of composites, while simultaneously preserving electrical insulation. A hybrid filler approach, using graphene and boron nitride, is presented as a possible technology providing for the independent control of electrical and thermal conduction. The reliability and lifespan performance of thermal interface materials is an important consideration towards the determination of appropriate practical applications. The present review addresses these issues in detail, demonstrating the promise of graphene-enhanced thermal interface materials compared to alternative technologies.

Phononic and photonic properties of shape-engineered silicon nanoscale pillar arrays.

We report the results of Brillouin-Mandelstam spectroscopy and Mueller matrix spectroscopic ellipsometry of the nanoscale 'pillar with the hat' periodic silicon structures, revealing intriguing phononic and photonic-phoxonic-properties. It has been theoretically shown that periodic structures with properly tuned dimensions can act simultaneously as phononic and photonic crystals, strongly affecting the light-matter interactions. Acoustic phonon states can be tuned by external boundaries, either as a result of phonon confinement effects in individual nanostructures, or as a result of artificially induced external periodicity, as in the phononic crystals. The shape of the nanoscale pillar array was engineered to ensure the interplay of both effects. The Brillouin-Mandelstam spectroscopy data indicated strong flattening of the acoustic phonon dispersion in the frequency range from 2 GHz to 20 GHz and the phonon wave vector extending to the higher-order Brillouin zones. The specifics of the phonon dispersion dependence on the pillar arrays' orientation suggest the presence of both periodic modulation and spatial localization effects for the acoustic phonons. The ellipsometry data reveal a distinct scatter pattern of four-fold symmetry due to nanoscale periodicity of the pillar arrays. Our results confirm the dual functionality of the nanostructured shape-engineered structure and indicate a possible new direction for fine-tuning the light-matter interaction in the next generation of photonic, optoelectronic, and phononic devices.

Low Resistivity and High Breakdown Current Density of 10 nm Diameter van der Waals TaSe3 Nanowires by Chemical Vapor Deposition.

Micron-scale single-crystal nanowires of metallic TaSe3, a material that forms -Ta-Se3-Ta-Se3- stacks separated from one another by a tubular van der Waals (vdW) gap, have been synthesized using chemical vapor deposition (CVD) on a SiO2/Si substrate, in a process compatible with semiconductor industry requirements. Their electrical resistivity was found unaffected by downscaling from the bulk to as little as 7 nm in nanowire width and height, in striking contrast to the resistivity of copper for the same dimensions. While the bulk resistivity of TaSe3 is substantially higher than that of bulk copper, at the nanometer scale the TaSe3 wires become competitive to similar-sized copper ones. Moreover, we find that the vdW TaSe3 nanowires sustain current densities in excess of 108 A/cm2 and feature an electromigration energy barrier twice that of copper. The results highlight the promise of quasi-one-dimensional transition metal trichalcogenides for electronic interconnect applications and the potential of van der Waals materials for downscaled electronics.

Strong Hot Carrier Effects in Single Nanowire Heterostructures.

We use transient Rayleigh scattering to study the thermalization of hot photoexcited carriers in single GaAs0.7Sb0.3/InP nanowire heterostructures. By comparing the energy loss rate in single core-only GaAs0.7Sb0.3 nanowires which do not show substantial hot carrier effects with the core-shell nanowires, we show that the presence of an InP shell substantially suppresses the longitudinal optical phonon emission rate at low temperatures which then leads to strong hot carrier effects.

Low-Frequency Current Fluctuations and Sliding of the Charge Density Waves in Two-Dimensional Materials.

We investigated low-frequency noise in two-dimensional (2D) charge density wave (CDW) systems, 1 T-TaS2 thin films, as they were driven from the nearly commensurate (NC) to incommensurate (IC) CDW phases by voltage and temperature stimuli. This study revealed that noise in 1 T-TaS2 has two pronounced maxima at the bias voltages, which correspond to the onset of CDW sliding and the NC-to-IC phase transition. We observed unusual Lorentzian features and exceptionally strong noise dependence on electric bias and temperature, leading to the conclusion that electronic noise in 2D CDW systems has a unique physical origin different from known fundamental noise types. We argue that noise spectroscopy can serve as a useful tool for understanding electronic transport phenomena in 2D CDW materials characterized by coexistence of different phases and strong pinning.

Low-Frequency Electronic Noise in Quasi-1D TaSe3 van der Waals Nanowires.

We report results of investigation of the low-frequency electronic excess noise in quasi-1D nanowires of TaSe3 capped with quasi-2D h-BN layers. Semimetallic TaSe3 is a quasi-1D van der Waals material with exceptionally high breakdown current density. It was found that TaSe3 nanowires have lower levels of the normalized noise spectral density, SI/I2, compared to carbon nanotubes and graphene (I is the current). The temperature-dependent measurements revealed that the low-frequency electronic 1/f noise becomes the 1/f2 type as temperature increases to ∼400 K, suggesting the onset of electromigration (f is the frequency). Using the Dutta-Horn random fluctuation model of the electronic noise in metals, we determined that the noise activation energy for quasi-1D TaSe3 nanowires is approximately EP ≈ 1.0 eV. In the framework of the empirical noise model for metallic interconnects, the extracted activation energy, related to electromigration is EA = 0.88 eV, consistent with that for Cu and Al interconnects. Our results shed light on the physical mechanism of low-frequency 1/f noise in quasi-1D van der Waals semimetals and suggest that such material systems have potential for ultimately downscaled local interconnect applications.

Phonons and thermal transport in graphene and graphene-based materials.

A discovery of the unusual thermal properties of graphene stimulated experimental, theoretical and computational research directed at understanding phonon transport and thermal conduction in two-dimensional material systems. We provide a critical review of recent results in the graphene thermal field focusing on phonon dispersion, specific heat, thermal conductivity, and comparison of different models and computational approaches. The correlation between the phonon spectrum in graphene-based materials and the heat conduction properties is analyzed in details. The effects of the atomic plane rotations in bilayer graphene, isotope engineering, and relative contributions of different phonon dispersion branches are discussed. For readers' convenience, the summaries of main experimental and theoretical results on thermal conductivity as well as phonon mode contributions to thermal transport are provided in the form of comprehensive annotated tables.

Thermal properties of graphene-copper-graphene heterogeneous films.

We demonstrated experimentally that graphene-Cu-graphene heterogeneous films reveal strongly enhanced thermal conductivity as compared to the reference Cu and annealed Cu films. Chemical vapor deposition of a single atomic plane of graphene on both sides of 9 µm thick Cu films increases their thermal conductivity by up to 24% near room temperature. Interestingly, the observed improvement of thermal properties of graphene-Cu-graphene heterofilms results primarily from the changes in Cu morphology during graphene deposition rather than from graphene's action as an additional heat conducting channel. Enhancement of thermal properties of graphene-capped Cu films is important for thermal management of advanced electronic chips and proposed applications of graphene in the hybrid graphene-Cu interconnect hierarchies.

Electronic Noise Spectroscopy of Quasi-Two-Dimensional Antiferromagnetic Semiconductors.

We investigated low-frequency current fluctuations, i.e., electronic noise, in FePS3 van der Waals layered antiferromagnetic semiconductor. The noise measurements have been used as noise spectroscopy for advanced materials characterization of the charge carrier dynamics affected by spin ordering and trapping states. Owing to the high resistivity of the material, we conducted measurements on vertical device configuration. The measured noise spectra reveal pronounced Lorentzian peaks of two different origins. One peak is observed only near the Néel temperature, and it is attributed to the corresponding magnetic phase transition. The second Lorentzian peak, visible in the entire measured temperature range, has characteristics of the trap-assisted generation-recombination processes similar to those in conventional semiconductors but shows a clear effect of the spin order reconfiguration near the Néel temperature. The obtained results contribute to understanding the electron and spin dynamics in this type of antiferromagnetic semiconductors and demonstrate the potential of electronic noise spectroscopy for advanced materials characterization.

Thermal conductivity of isotopically modified graphene.

In addition to its exotic electronic properties graphene exhibits unusually high intrinsic thermal conductivity. The physics of phonons--the main heat carriers in graphene--has been shown to be substantially different in two-dimensional (2D) crystals, such as graphene, from in three-dimensional (3D) graphite. Here, we report our experimental study of the isotope effects on the thermal properties of graphene. Isotopically modified graphene containing various percentages of 13C were synthesized by chemical vapour deposition (CVD). The regions of different isotopic compositions were parts of the same graphene sheet to ensure uniformity in material parameters. The thermal conductivity, K, of isotopically pure 12C (0.01% 13C) graphene determined by the optothermal Raman technique, was higher than 4,000 W mK(-1) at the measured temperature T(m)~320 K, and more than a factor of two higher than the value of K in graphene sheets composed of a 50:50 mixture of 12C and 13C. The experimental data agree well with our molecular dynamics (MD) simulations, corrected for the long-wavelength phonon contributions by means of the Klemens model. The experimental results are expected to stimulate further studies aimed at a better understanding of thermal phenomena in 2D crystals.

Graphene-multilayer graphene nanocomposites as highly efficient thermal interface materials.

We found that the optimized mixture of graphene and multilayer graphene, produced by the high-yield inexpensive liquid-phase-exfoliation technique, can lead to an extremely strong enhancement of the cross-plane thermal conductivity K of the composite. The "laser flash" measurements revealed a record-high enhancement of K by 2300% in the graphene-based polymer at the filler loading fraction f = 10 vol %. It was determined that the relatively high concentration of the single-layer and bilayer graphene flakes (~10-15%) present simultaneously with the thicker multilayers of large lateral size (~1 µm) were essential for the observed unusual K enhancement. The thermal conductivity of the commercial thermal grease was increased from an initial value of ~5.8 W/mK to K = 14 W/mK at the small loading f = 2%, which preserved all mechanical properties of the hybrid. Our modeling results suggest that graphene-multilayer graphene nanocomposite used as the thermal interface material outperforms those with carbon nanotubes or metal nanoparticles owing to graphene's aspect ratio and lower Kapitza resistance at the graphene-matrix interface.

Anomalous size dependence of the thermal conductivity of graphene ribbons.

We investigated the thermal conductivity K of graphene ribbons and graphite slabs as the function of their lateral dimensions. Our theoretical model considered the anharmonic three-phonon processes to the second-order and included the angle-dependent phonon scattering from the ribbon edges. It was found that the long mean free path of the long-wavelength acoustic phonons in graphene can lead to an unusual nonmonotonic dependence of the thermal conductivity on the length L of a ribbon. The effect is pronounced for the ribbons with the smooth edges (specularity parameter p > 0.5). Our results also suggest that, contrary to what was previously thought, the bulk-like three-dimensional phonons in graphite make a rather substantial contribution to its in-plane thermal conductivity. The Umklapp-limited thermal conductivity of graphite slabs scales, for L below ∼30 µm, as log(L), while for larger L, the thermal conductivity approaches a finite value following the dependence K(0) - A × L(-1/2), where K(0) and A are parameters independent of the length. Our theoretical results clarify the scaling of the phonon thermal conductivity with the lateral sizes in graphene and graphite. The revealed anomalous dependence K(L) for the micrometer-size graphene ribbons can account for some of the discrepancy in reported experimental data for graphene.

Charge density waves in exfoliated films of van der Waals materials: evolution of Raman spectrum in TiSe2.

A number of the charge-density-wave materials reveal a transition to the macroscopic quantum state around 200 K. We used graphene-like mechanical exfoliation of TiSe(2) crystals to prepare a set of films with different thicknesses. The transition temperature to the charge-density-wave state was determined via modification of Raman spectra of TiSe(2) films. It was established that the transition temperature can increase from its bulk value to ~240 K as the thickness of the van der Waals films reduces to the nanometer range. The obtained results are important for the proposed applications of such materials in the collective-state information processing, which require room-temperature operation.

Graphene-on-diamond devices with increased current-carrying capacity: carbon sp2-on-sp3 technology.

Graphene demonstrated potential for practical applications owing to its excellent electronic and thermal properties. Typical graphene field-effect transistors and interconnects built on conventional SiO(2)/Si substrates reveal the breakdown current density on the order of 1 µA/nm(2) (i.e., 10(8) A/cm(2)), which is ~100× larger than the fundamental limit for the metals but still smaller than the maximum achieved in carbon nanotubes. We show that by replacing SiO(2) with synthetic diamond, one can substantially increase the current-carrying capacity of graphene to as high as ~18 µA/nm(2) even at ambient conditions. Our results indicate that graphene's current-induced breakdown is thermally activated. We also found that the current carrying capacity of graphene can be improved not only on the single-crystal diamond substrates but also on an inexpensive ultrananocrystalline diamond, which can be produced in a process compatible with a conventional Si technology. The latter was attributed to the decreased thermal resistance of the ultrananocrystalline diamond layer at elevated temperatures. The obtained results are important for graphene's applications in high-frequency transistors, interconnects, and transparent electrodes and can lead to the new planar sp(2)-on-sp(3) carbon-on-carbon technology.

Selective gas sensing with a single pristine graphene transistor.

We show that vapors of different chemicals produce distinguishably different effects on the low-frequency noise spectra of graphene. It was found in a systematic study that some gases change the electrical resistance of graphene devices without changing their low-frequency noise spectra while other gases modify the noise spectra by inducing Lorentzian components with distinctive features. The characteristic frequency f(c) of the Lorentzian noise bulges in graphene devices is different for different chemicals and varies from f(c) = 10-20 Hz to f(c) = 1300-1600 Hz for tetrahydrofuran and chloroform vapors, respectively. The obtained results indicate that the low-frequency noise in combination with other sensing parameters can allow one to achieve the selective gas sensing with a single pristine graphene transistor. Our method of gas sensing with graphene does not require graphene surface functionalization or fabrication of an array of the devices with each tuned to a certain chemical.

Quantum Composites with Charge-Density-Wave Fillers.

A unique class of advanced materials-quantum composites based on polymers with fillers composed of a van der Waals quantum material that reveals multiple charge-density-wave quantum condensate phases-is demonstrated. Materials that exhibit quantum phenomena are typically crystalline, pure, and have few defects because disorder destroys the coherence of the electrons and phonons, leading to collapse of the quantum states. The macroscopic charge-density-wave phases of filler particles after multiple composite processing steps are successfully preserved in this work. The prepared composites display strong charge-density-wave phenomena even above room temperature. The dielectric constant experiences more than two orders of magnitude enhancement while the material maintains its electrically insulating properties, opening a venue for advanced applications in energy storage and electronics. The results present a conceptually different approach for engineering the properties of materials, extending the application domain for van der Waals materials.

Cryogenic characteristics of graphene composites-evolution from thermal conductors to thermal insulators.

The development of cryogenic semiconductor electronics and superconducting quantum computing requires composite materials that can provide both thermal conduction and thermal insulation. We demonstrated that at cryogenic temperatures, the thermal conductivity of graphene composites can be both higher and lower than that of the reference pristine epoxy, depending on the graphene filler loading and temperature. There exists a well-defined cross-over temperature-above it, the thermal conductivity of composites increases with the addition of graphene; below it, the thermal conductivity decreases with the addition of graphene. The counter-intuitive trend was explained by the specificity of heat conduction at low temperatures: graphene fillers can serve as, both, the scattering centers for phonons in the matrix material and as the conduits of heat. We offer a physical model that explains the experimental trends by the increasing effect of the thermal boundary resistance at cryogenic temperatures and the anomalous thermal percolation threshold, which becomes temperature dependent. The obtained results suggest the possibility of using graphene composites for, both, removing the heat and thermally insulating components at cryogenic temperatures-a capability important for quantum computing and cryogenically cooled conventional electronics.

Thermal properties of graphene and nanostructured carbon materials.

Recent years have seen a rapid growth of interest by the scientific and engineering communities in the thermal properties of materials. Heat removal has become a crucial issue for continuing progress in the electronic industry, and thermal conduction in low-dimensional structures has revealed truly intriguing features. Carbon allotropes and their derivatives occupy a unique place in terms of their ability to conduct heat. The room-temperature thermal conductivity of carbon materials span an extraordinary large range--of over five orders of magnitude--from the lowest in amorphous carbons to the highest in graphene and carbon nanotubes. Here, I review the thermal properties of carbon materials focusing on recent results for graphene, carbon nanotubes and nanostructured carbon materials with different degrees of disorder. Special attention is given to the unusual size dependence of heat conduction in two-dimensional crystals and, specifically, in graphene. I also describe the prospects of applications of graphene and carbon materials for thermal management of electronics.

Charge-Density-Wave Thin-Film Devices Printed with Chemically Exfoliated 1T-TaS2 Ink.

We report on the preparation of inks containing fillers derived from quasi-two-dimensional charge-density-wave materials, their application for inkjet printing, and the evaluation of their electronic properties in printed thin-film form. The inks were prepared by liquid-phase exfoliation of CVT-grown 1T-TaS2 crystals to produce fillers with nm-scale thickness and µm-scale lateral dimensions. Exfoliated 1T-TaS2 was dispersed in a mixture of isopropyl alcohol and ethylene glycol to allow fine-tuning of filler particles thermophysical properties for inkjet printing. The temperature-dependent electrical and current fluctuation measurements of printed thin films demonstrated that the charge-density-wave properties of 1T-TaS2 are preserved after processing. The functionality of the printed thin-film devices can be defined by the nearly commensurate to the commensurate charge-density-wave phase transition of individual exfoliated 1T-TaS2 filler particles rather than by electron-hopping transport between them. The obtained results are important for the development of printed electronics with diverse functionality achieved by the incorporation of quasi-two-dimensional van der Waals quantum materials.

Electrical Gating of the Charge-Density-Wave Phases in Two-Dimensional h-BN/1T-TaS2 Devices.

We report on the electrical gating of the charge-density-wave phases and current in h-BN-capped three-terminal 1T-TaS2 heterostructure devices. It is demonstrated that the application of a gate bias can shift the source-drain current-voltage hysteresis associated with the transition between the nearly commensurate and incommensurate charge-density-wave phases. The evolution of the hysteresis and the presence of abrupt spikes in the current while sweeping the gate voltage suggest that the effect is electrical rather than self-heating. We attribute the gating to an electric-field effect on the commensurate charge-density-wave domains in the atomic planes near the gate dielectric. The transition between the nearly commensurate and incommensurate charge-density-wave phases can be induced by both the source-drain current and the electrostatic gate. Since the charge-density-wave phases are persistent in 1T-TaS2 at room temperature, one can envision memory applications of such devices when scaled down to the dimensions of individual commensurate domains and few-atomic plane thicknesses.