Gravitationally Driven Wicking for Enhanced Condensation Heat Transfer.

Vapor condensation is routinely used as an effective means of transferring heat or separating fluids. Filmwise condensation is prevalent in typical industrial-scale systems, where the condensed fluid forms a thin liquid film due to the high surface energy associated with many industrial materials. Conversely, dropwise condensation, where the condensate forms discrete liquid droplets which grow, coalesce, and shed, results in an improvement in heat transfer performance of an order of magnitude compared to filmwise condensation. However, current state-of-the-art dropwise technology relies on functional hydrophobic coatings, for example, long chain fatty acids or polymers, which are often not robust and therefore undesirable in industrial conditions. In addition, low surface tension fluid condensates, such as hydrocarbons, pose a unique challenge because common hydrophobic condenser coatings used to shed water (with a surface tension of 73 mN/m) often do not repel fluids with lower surface tensions (<25 mN/m). We demonstrate a method to enhance condensation heat transfer using gravitationally driven flow through a porous metal wick, which takes advantage of the condensate's affinity to wet the surface and also eliminates the need for condensate-phobic coatings. The condensate-filled wick has a lower thermal resistance than the fluid film observed during filmwise condensation, resulting in an improved heat transfer coefficient of up to an order of magnitude and comparable to that observed during dropwise condensation. The improved heat transfer realized by this design presents the opportunity for significant energy savings in natural gas processing, thermal management, heating and cooling, and power generation.

Conductive block copolymer elastomers and psychophysical thresholding for accurate haptic effects.

Electrotactile stimulus is a form of sensory substitution in which an electrical signal is perceived as a mechanical sensation. The electrotactile effect could, in principle, recapitulate a range of tactile experience by selective activation of nerve endings. However, the method has been plagued by inconsistency, galvanic reactions, pain and desensitization, and unwanted stimulation of nontactile nerves. Here, we describe how a soft conductive block copolymer, a stretchable layout, and concentric electrodes, along with psychophysical thresholding, can circumvent these shortcomings. These purpose-designed materials, device layouts, and calibration techniques make it possible to generate accurate and reproducible sensations across a cohort of 10 human participants and to do so at ultralow currents (≥6 microamperes) without pain or desensitization. This material, form factor, and psychophysical approach could be useful for haptic devices and as a tool for activation of the peripheral nervous system.

Intrinsically Stretchable Block Copolymer Based on PEDOT:PSS for Improved Performance in Bioelectronic Applications.

The conductive polyelectrolyte complex poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is ubiquitous in research dealing with organic electronic devices (e.g., solar cells, wearable and implantable sensors, and electrochemical transistors). In many bioelectronic applications, the applicability of commercially available formulations of PEDOT:PSS (e.g., Clevios) is limited by its poor mechanical properties. Additives can be used to increase the compliance but pose a risk of leaching, which can result in device failure and increased toxicity (in biological settings). Thus, to increase the mechanical compliance of PEDOT:PSS without additives, we synthesized a library of intrinsically stretchable block copolymers. In particular, controlled radical polymerization using a reversible addition-fragmentation transfer process was used to generate block copolymers consisting of a block of PSS (of fixed length) appended to varying blocks of poly(poly(ethylene glycol) methyl ether acrylate) (PPEGMEA). These block copolymers (PSS(1)-b-PPEGMEA(x), where x ranges from 1 to 6) were used as scaffolds for oxidative polymerization of PEDOT. By increasing the lengths of the PPEGMEA segments on the PEDOT:[PSS(1)-b-PPEGMEA(1-6)] block copolymers, ("Block-1" to "Block-6"), or by blending these copolymers with PEDOT:PSS, the mechanical and electronic properties of the polymer can be tuned. Our results indicate that the polymer with the longest block of PPEGMEA, Block-6, had the highest fracture strain (75%) and lowest elastic modulus (9.7 MPa), though at the expense of conductivity (0.01 S cm-1). However, blending Block-6 with PEDOT:PSS to compensate for the insulating nature of the PPEGMEA resulted in increased conductivity [2.14 S cm-1 for Blend-6 (2:1)]. Finally, we showed that Block-6 outperforms a commercial formulation of PEDOT:PSS as a dry electrode for surface electromyography due to its favorable mechanical properties and better adhesion to skin.