Effect of hot water maceration, rehydration, and soft tissue presence on 3D geometry of bone.

PURPOSE: In forensic medicine, maceration is often essential for examining bone surfaces, serving purposes such as identifying cut marks, making geometric measurements, and determining the victim's age. While hot water maceration removes soft tissue effectively, it is known to cause bone surface shrinkage. This raises the question of whether this effect is permanent or if it can be partially reversed through rehydration, considering the presence of soft tissue. METHODS: Computed tomography (CT) scans were conducted on the radii of 20 paired human anatomic forearm specimens. Subsequently, the radii were extracted, macerated in 60 °C water, CT-scanned in an air environment, rehydrated, re-implanted into the forearms, and CT-scanned again. RESULTS: Maceration resulted in a mean shrinkage of 0.12 mm on the outer bone surface. This shrinkage was nearly fully recoverable for the diaphysis after rehydration and accounting for soft tissue surrounding the bone. In contrast, the epiphysis showed permanent shrinkage, likely due to the loss of small bone fragments. Analysis of the inner bone surface indicated a smaller effect, but with significant standard deviations, especially for the epiphysis, possibly related to the less well-defined nature of the inner bone surface. CONCLUSION: The epiphyseal surface of hot water-macerated bone will, on average, be approximately 0.15 mm deflated and cannot retain the original surface. On the other hand, the diaphyseal surface is less affected and can be nearly completely restored after rehydration and accounting for soft tissue surrounding the bone.

Patient-Specific Guides for Accurate and Precise Positioning of Osseointegrated Implants in Transfemoral Amputations: A Proof-of-Concept In Vitro Study.

Background and Objectives: The treatment of transfemoral amputees using osseointegrated implants for prosthetic anchorage requires accurate implant positioning when using threaded bone-anchoring implants due to the curvature of the femur and the risk of cortical penetration in misaligned implants. This study investigated the accuracy and precision in implant positioning using additively manufactured case-specific positioning guides. Materials and Methods: The geometry and density distribution of twenty anatomic specimens of human femora were assessed in quantitative computed tomography (QCT) scanning. The imaging series were used to create digital 3D specimen models, preoperatively plan the optimal implant position and manufacture specimen-specific positioning guides. Following the surgical bone preparation and insertion of the fixture (threaded bone-anchoring element) (OPRA; Integrum AB, Mölndal, Sweden), a second QCT imaging series and 3D model design were conducted to assess the operatively achieved implant position. The 3D models were registered and the deviations of the intraoperatively achieved implant position from the preoperatively planned implant position were analyzed as follows. The achieved, compared to the planned implant position, was presented as resulting mean hip abduction or adduction (A/A) and extension or flexion (E/F) and mean implant axis offset in medial or lateral (M/L) and anterior or posterior (A/P) direction measured at the most distal implant axis point. Results: The achieved implant position deviated from the preoperative plan by 0.33 ± 0.33° (A/A) and 0.68 ± 0.66° (E/F) and 0.62 ± 0.55 mm (M/L) and 0.68 ± 0.56 mm (A/P), respectively. Conclusions: Using case-specific guides, it was feasible to achieve not only accurate but also precise positioning of the implants compared to the preoperative plan. Thus, their design and application in the clinical routine should be considered, especially in absence of viable alternatives.

Biomechanical evaluation of the proximal chevron osteotomy in comparison to the Lapidus arthrodesis for the correction of hallux valgus deformities.

PURPOSE: The proximal chevron osteotomy and the modified Lapidus arthrodesis are both procedures utilized for deformity correction in patients with severe symptomatic hallux valgus. The aim of the current study was to compare their biomechanical stability when using locking plate fixation. METHODS: Twelve matched pairs of human anatomical lower leg specimens underwent on one side a proximal chevron osteotomy with a medial locking plate and on the other side a modified Lapidus arthrodesis with a plantar locking plate utilizing an interfragmentary compression screw. All specimens underwent bone mineral density (BMD) assessment and were tested in a servohydraulic load frame which applied a load on the centre of the metatarsal head over 1000 loading cycles with subsequently ultimate load testing. Displacement of the proximal and distal bone segment, ultimate load, and bending stiffness were analyzed. RESULTS: Mean displacement of both procedures showed no statistically significant difference throughout all the loading cycles (0.213 ≤ p ≤ 0.834). The mean ultimate load of the proximal chevron osteotomy was 227.9 N (± 232.4) and of the modified Lapidus arthrodesis 162.9 N (± 74.6) (p = 0.754). The proximal chevron osteotomy (38.2 N/mm (± 24.9)) had a significantly higher bending stiffness compared to the modified Lapidus arthrodesis (17.3 N/mm (± 9.9)) (p = 0.009). There was no correlation between BMD and displacement in all loading cycles, ultimate load, and bending stiffness of either procedure (p > 0.05). CONCLUSION: Although the bending stiffness of the chevron osteotomy was higher, there was no statistically significant difference between the surgical techniques in mean displacement and ultimate load. The BMD did not influence the overall stability of either reconstruction. Locking plate fixation increases the clinical value of the modified Lapidus arthrodesis by outweighing most of the biomechanical disadvantages in comparison to the proximal chevron osteotomy.

On Measuring Implant Fixation Stability in ACL Reconstruction.

Numerous methods and devices are available for implant fixation in anterior cruciate ligament (ACL) reconstruction. Biomechanical data indicate high variability in fixation stability across different devices. This study aims to provide a better insight into measuring the structural characteristics and mechanical behavior of ACL implant fixations. Fourteen human tibial specimens with reconstructed ACLs were subjected to progressively increasing dynamic loading until failure. The motions of the tibia, the proximal and distal graft ends, as well as the testing frame and actuator, were continuously recorded via a motion tracking system. Significantly higher displacements of the machine actuator (1.0 mm at graft slippage onset, and 12.2 mm at ultimate load) were measured compared to the displacements of the proximal (0.8 and 4.3 mm, respectively) and distal graft (0.1 and 3.4 mm, respectively) ends. The displacements measured at different sites showed significant correlations. The provided data suggest significant and systematic inaccuracies in the stiffness and slippage of the fixation when using machine displacement, as commonly reported in the literature. The assessment of the distal graft displacement excludes the artifactual graft elongation, and most accurately reflects the graft slippage onset indicating clinical failure. Considering the high displacement at the ultimate load, the ultimate load could be used as a standardized variable to compare different fixation methods. However, the ultimate load alone is not sufficient to qualitatively describe fixation stability.

Thermal Effects during Bone Preparation and Insertion of Osseointegrated Transfemoral Implants.

BACKGROUND: The preparation of bone for the insertion of an osseointegrated transfemoral implant and the insertion process are performed at very low speeds in order to avoid thermal damages to bone tissue which may potentially jeopardize implant stability. The aim of this study was to quantify the temperature increase in the femur at different sites and insertion depths, relative to the final implant position during the stepwise implantation procedure. METHODS: The procedure for installation of the osseointegrated implant was performed on 24 femoral specimens. In one specimen of each pair, the surgery was performed at the clinically practiced speed, while the speed was doubled in the contralateral specimen. Six 0.075 mm K fine gauge thermocouples (RS Components, Sorby, UK) were inserted into the specimen at a distance of 0.5 mm from the final implant surface, and six were inserted at a distance of 1.0 mm. RESULTS: Drilling caused a temperature increase of <2.5 °C and was not statistically significantly different for most drill sizes (0.002 < p < 0.845). The mean increase in temperature during thread tapping and implant insertion was <5.0 °C, whereas the speed had an effect on the temperature increase during thread tapping. CONCLUSIONS: Drilling is the most time-consuming part of the surgery. Doubling the clinically practiced speed did not generate more heat during this step, suggesting the speed and thus the time- and cost-effectiveness of the procedure could be increased. The frequent withdrawal of the instruments and removal of the bone chips is beneficial to prevent temperature peaks, especially during thread tapping.

Peroneus brevis as source of instability in Jones fracture fixation.

PURPOSE: Intramedullary screw fixation is currently considered the gold standard treatment for Jones fractures in the athlete. Besides biological factors (i.e., poor vascularization), mechanical instability induced by the pull of the peroneus brevis tendon (PBT) contributes to deficient Jones fracture healing. This biomechanical study aimed to simulate loads induced by the PBT at the fifth metatarsal and to compare the stability of two intramedullary screw constructs in a Jones fracture fixation model. METHODS: Jones fractures were created in 24 human paired specimens, and fixation was achieved with either a solid Jones fracture specific screw (JFXS) (Jones Screw; Arthrex Inc., Naples FL, USA) or a cannulated headless compression screw (HCS) (HCS; DePuySynthes, Solothurn, Switzerland). The PBT was fixed to a mechanical load frame by the use of a cryoclamp. Constructs were loaded in tension for 1000 cycles, followed by an ultimate load test. Construct failure was defined by exceeding 10° of dorsal angulation. RESULTS: Preliminary failure occurred more often in HCS constructs (33%) compared to JFXS constructs (0%) (P = 0.044). Mean tensile load to failure reached 123.8 ± 91.4 N in the JFXS group and 91.5 ± 62.2 N in the HCS group (P = 0.337). The mean slope of the load-displacement curve was 24.2 ± 10.4 N/mm for JFXS constructs and 24.7 ± 5.5 N/mm for HCS constructs, respectively (P = 0.887). CONCLUSION: This is the first study evaluating the effect of PBT pull on the mechanical stability of Jones fracture fixation. Higher preliminary failure rates of HCS were found under cyclic loading conditions compared to JFXS.

Biomechanical evaluation of different ankle orthoses in a simulated lateral ankle sprain in two different modes.

Ankle orthoses are commonly used for prevention of recurrent ankle sprains. While there are some data on their functional performance or restriction of range of motion, there is little knowledge on the quantifiable passive mechanical effectiveness of various devices. This study aimed to determine the prophylactic stabilization effect for commonly prescribed ankle orthoses in a simulated recurrent ankle sprain. Eleven anatomic lower leg specimens were tested in plantar flexion and hindfoot inversion in a simulated ankle sprain in a quasi-static and dynamic test mode at 0.5°/s and 50°/s internal rotation, respectively. Tests included intact specimens, same specimens with the ruptured anterior talofibular ligament (ATFL), followed by stabilization with five different semi-rigid orthoses: AirGo Ankle Brace, Air Stirrup Ankle Brace, Dyna Ankle 50S1, MalleoLoc, and Aequi. Compared to the injured and unprotected state, two orthoses (AirGo and Air Stirrup) significantly reinforced the ankle. The Aequi ankle brace restored stability comparable to an intact joint. Dyna Ankle 50S1 and MalleoLoc provided insufficient resistance to applied internal rotation compared to the ankle with ruptured ATFL. Ankle orthoses varied significantly in their ability to stabilize the unstable ankle during an ankle sprain in both testing modes. Presented objective data on passive stabilization reveal a lack of supporting evidence for clinical application of ankle orthoses.

The role of the subchondral layer in osteonecrosis of the femoral head: analysis based on HR-QCT in comparison to MRI findings.

BACKGROUND: Non-traumatic avascular osteonecrosis of the femoral head (ONFH) is a severe disease causing destruction of the hip joint, often necessitating total hip arthroplasty (THA) even in young patients. Magnetic resonance imaging (MRI) is commonly used for diagnosis of ONFH, but provides limited insight into the subchondral bone microstructure. PURPOSE: To analyze routine MRI findings in comparison to high-resolution quantitative computed tomography (HR-QCT) with a special focus on the subchondral layer and to estimate the importance of differences determining the indication for THA. MATERIAL AND METHODS: Twelve patients with ONFH were included before THA. Preoperative MRI and HR-QCT of the retrieved femoral heads were aligned using a registration algorithm. Pathological findings and trabecular bone parameters in matched areas were analyzed by two readers. McNemar, marginal homogeneity test, and Pearson's correlation coefficient were used for comparison. RESULTS: Subchondral delamination was found in nine cases on HR-QCT, but missed or underestimated in all but one case on MRI ( P = 0.016). Chondral discontinuity was found in all cases on HR-QCT and in two cases on MRI ( P = 0.016). Areas of complete bone resorption on HR-QCT were linked to high signal intensity on 3D gradient-echo MRI sequences with water-selective excitation, while there was no correlation between trabecular bone parameters and MRI signal intensities in other areas ( P = 0.304). CONCLUSION: Subchondral delamination, subchondral resorption, and chondral discontinuity are found frequently in advanced stages of ONFH. These lesions tend to be underestimated on conventional MRI. Our results support the importance of CT imaging in the evaluation of ONFH.

Evaluation of Aerosol Electrospray Analysis of Metal-on-Metal Wear Particles from Simulated Total Joint Replacement.

Wear is a common cause for aseptic loosening in artificial joints. The purpose of this study was to develop an automated diagnostical method for identification of the number and size distribution of wear debris. For this purpose, metal debris samples were extracted from a hip simulator and then analyzed by the electrospray method combined with a differential mobility analyzer, allowing particle detection ranging from several nanometers up to 1 µm. Wear particles were identified with a characteristic peak at 15 nm. The electrospray setup was successfully used and validated for the first time to characterize wear debris from simulated total joint replacement. The advantages of this diagnostic method are its time- and financial efficiency and its suitability for testing of different materials.

Measurement considerations on examiner-dependent factors in the ultrasound assessment of developmental dysplasia of the hip.

PURPOSE: The standardized sonographic hip screening according to Graf has increased reliability and comparability of measurements in the screening of developmental dysplasia of the hip (DDH). However, examiner dependent factors have been discussed to influence sonographic measurements. The objectives of this study were to examine the tolerance of the transducer positioning and to analyse the impact of transducer inclinations on Graf's hip grading system. MATERIALS AND METHODS: Twenty-four hips in consecutive newborns were screened sonographically in combination with an optoelectronic motion capture system to trace transducer positions in space. Subsequently five defined inclinations of the transducer relative to Graf's neutral transducer position were analysed, giving a total of 144 sonographic images. RESULTS: We found a permissible transducer inclination in the axial plane of 8.8° to anterior and 8.1° to posterior. In the frontal plane we found a permissible inclination of 15.4° to caudal and 7.2° to cranial. The impact on the α-angle was significant for posterior-cranial (p < 0.001), cranial (p = 0.009), and caudal (p < 0.001) inclined transducer positions. The effect on the results according to Graf's grading system was significant for the caudal inclination of the transducer position (p < 0.001). CONCLUSION: Our findings show that the standardized plane defined by Graf's criteria allows notable inclinations of the transducer positions. Transducer inclinations show an impact on measurement results, which are clinically relevant. Those effects cannot be ruled out using Graf's ultrasound criteria alone. The examiner should pay attention to avoid transducer inclinations in the frontal plane and a combination of posterior and cranial inclination.

Peroneal tendinosis as a predisposing factor for the acute lateral ankle sprain in runners.

PURPOSE: A painful episode in the region of the peroneal tendons, within the retromalleolar groove, is a common precipitating event of an acute lateral ankle sprain. A forefoot striking pattern is suspected to cause peroneal tendinosis. The aim of this study is to analyse the role of peroneal tendinosis as a predisposing factor for ankle sprain trauma in runners. METHODS: Fifty-eight runners who had experienced acute ankle sprain trauma, with pre-existing pain episodes for up to 4 weeks in the region of the peroneal tendons, were assessed clinically. Fractures were excluded by conventional radiography. An magnetic resonance imaging (MRI) scan had been performed within 14 days after the traumatic event and was subsequently evaluated by two experienced radiologists. RESULTS: MRI revealed peroneal tendinosis in 55 patients (95% of the total study population). Peroneus brevis (PB) tendinosis was found in 48 patients (87% of all patients with peroneal tendinosis), and peroneus longus (PL) tendinosis was observed in 42 cases (76%). Thirty-five patients (64%) had combined PB and PL tendinosis. A lesion of the anterior talofibular ligament was found to be the most common ligament injury associated with peroneal tendinosis (29 cases; 53%), followed by a lesion of the calcaneofibular ligament (16 cases; 29%) and a lesion of the posterior tibiofibular ligament (13 cases; 24%). CONCLUSION: The results of this study reflect the correlation between peroneal tendinosis and ankle sprain trauma. Injuries of one or more ligaments are associated with further complications. A period of rest or forbearance of sports as well as adequate treatment of the peroneal tendinosis is essential to prevent subsequent ankle injuries, especially in runners. Modification of the running technique would also be beneficial. LEVEL OF EVIDENCE: IV.

The role of the medial ligaments in lateral stabilization of the ankle joint: an in vitro study.

PURPOSE: The deltoid ligament complex is known as medial stabilizer in the ankle against pronation/eversion. Lateral dual-ligament laxity often results in chronic ankle instability with recurring ankle sprain trauma. The goal of this study is to examine the lateral stabilizing role of the deltoid ligament complex against supination/inversion in case of existing lateral ligament instability. METHODS: A torsion simulation was performed on 12 fresh human lower leg cadaver specimens in a loading frame and a specially designed mounting platform. The preset torsion between tibia and calcaneus was primarily set at 30° of internal rotation on specimen in plantar flexion and hindfoot inversion. The measured variable was the resisting torque recorded around mechanical tibial axis, which ensures stability in ankle sprain trauma. The first series of measurements were performed on healthy specimens and the following after transecting structures in following order: anterior talofibular ligament (ATFL) in combination with calcaneofibular ligament (CFL), followed by anterior tibiotalar ligament and posterior tibiotalar ligament and finally tibiocalcaneal ligament (TCL). RESULTS: The combined lateral ATFL and CFL instability showed a decrease in the resisting torque, which ensures stability in ankle sprain trauma. Only a transection of TCL (superficial layer of deltoid ligament complex) with existing lateral dual-ligament instability results in a significant decrease in torque (p<0.0001). CONCLUSION: The goal of the study was to provide the orthopaedic and/or trauma surgeon with quantitative data that may be referred to the substantial stabilizing effect of TCL against supination/inversion in the ankle joint in case of repetitive sprain trauma at a present lateral ligament lesion. Diagnostics of and treatment for lateral ligament instability need to consider the deltoid ligament complex,especially TCL in clinical routine.

Biomechanical analysis of two fixation methods for proximal chevron osteotomy of the first metatarsal.

PURPOSE: The proximal chevron osteotomy provides high correctional power. However, relatively high rates of dorsiflexion malunion of up to 17 % are reported for this procedure. This leads to insufficient weight bearing of the first ray and therefore to metatarsalgia. Recent biomechanical and clinical studies pointed out the importance of rigid fixation of proximal metatarsal osteotomies. Therefore, the aim of the present study was to compare biomechanical properties of fixation of proximal chevron osteotomies with variable locking plate and cancellous screw respectively. METHODS: Ten matched pairs of human fresh frozen cadaveric first metatarsals underwent proximal chevron osteotomy with either variable locking plate or cancellous screw fixation after obtaining bone mineral density. Biomechanical testing included repetitive plantar to dorsal loading from 0 to 31 N with the 858 Mini Bionix(®) (MTS(®) Systems Corporation, Eden Prairie, MN, USA). Dorsal angulation of the distal fragment was recorded. RESULTS: The variable locking plate construct reveals statistically superior results in terms of bending stiffness and dorsal angulation compared to the cancellous screw construct. There was a statistically significant correlation between bone mineral density and maximum tolerated load until construct failure occurred for the screw construct (r = 0.640, p = 0.406). CONCLUSION: The results of the present study indicate that variable locking plate fixation shows superior biomechanical results to cancellous screw fixation for proximal chevron osteotomy. Additionally, screw construct failure was related to levels of low bone mineral density. Based on the results of the present study we recommend variable locking plate fixation for proximal chevron osteotomy, especially in osteoporotic bone.

Mechanical properties of additively manufactured lattice structures composed of zirconia and hydroxyapatite ceramics.

Ceramic lattices hold great potential for bone scaffolds to facilitate bone regeneration and integration of native tissue with medical implants. While there have been several studies on additive manufacturing of ceramics and their osseointegrative and osteoconductive properties, there is a lack of a comprehensive examination of their mechanical behavior. Therefore, the aim of this study was to assess the mechanical properties of different additively manufactured ceramic lattice structures under different loading conditions and their overall ability to mimic bone tissue properties. Eleven different lattice structures were designed and manufactured with a porosity of 80% using two materials, hydroxyapatite (HAp) and zirconium dioxide (ZrO2). Six cell-based lattices with cubic and hexagonal base, as well as five Voronoi-based lattices were considered in this study. The samples were manufactured using lithography-based ceramic additive manufacturing and post-processed thermally prior to mechanical testing. Cell-based lattices with cubic and hexagonal base, as well as Voronoi-based lattices were considered in this study. The lattices were tested under four loading conditions: compression, four-point bending, shear and tension. The manufacturing process of the different ceramics leads to different deviations of the lattice geometry, hence, the elastic properties of one structure cannot be directly inferred from one material to another. ZrO2 lattices prove to be stiffer than HAp lattices of the same designed structure. The Young's modulus for compression of ZrO2 lattices ranges from 2 to 30GPa depending on the used lattice design and for HAp 200MPa to 3.8GPa. The expected stability, the load where 63.2% of the samples are expected to be destroyed, of the lattices ranges from 81 to 553MPa and for HAp 6 to 42MPa. For the first time, a comprehensive overview of the mechanical properties of various additively manufactured ceramic lattice structures is provided. This is intended to serve as a reference for designers who would like to expand the design capabilities of ceramic implants that will lead to an advancement in their performance and ability to mimic human bone tissue.

Dimensional accuracy and precision and surgeon perception of additively manufactured bone models: effect of manufacturing technology and part orientation.

BACKGROUND: Additively manufactured (AM) anatomical bone models are primarily utilized for training and preoperative planning purposes. As such, they must meet stringent requirements, with dimensional accuracy being of utmost importance. This study aimed to evaluate the precision and accuracy of anatomical bone models manufactured using three different AM technologies: digital light processing (DLP), fused deposition modeling (FDM), and PolyJetting (PJ), built in three different part orientations. Additionally, the study sought to assess surgeons' perceptions of how well these models mimic real bones in simulated osteosynthesis. METHODS: Computer-aided design (CAD) models of six human radii were generated from computed tomography (CT) imaging data. Anatomical models were then manufactured using the three aforementioned technologies and in three different part orientations. The surfaces of all models were 3D-scanned and compared with the original CAD models. Furthermore, an anatomical model of a proximal femur including a metastatic lesion was manufactured using the three technologies, followed by (mock) osteosynthesis performed by six surgeons on each type of model. The surgeons' perceptions of the quality and haptic properties of each model were assessed using a questionnaire. RESULTS: The mean dimensional deviations from the original CAD model ranged between 0.00 and 0.13 mm with maximal inaccuracies < 1 mm for all models. In surgical simulation, PJ models achieved the highest total score on a 5-point Likert scale ranging from 1 to 5 (with 1 and 5 representing the lowest and highest level of agreement, respectively), (3.74 ± 0.99) in the surgeons' perception assessment, followed by DLP (3.41 ± 0.99) and FDM (2.43 ± 1.02). Notably, FDM was perceived as unsuitable for surgical simulation, as the material melted during drilling and sawing. CONCLUSIONS: In conclusion, the choice of technology and part orientation significantly influenced the accuracy and precision of additively manufactured bone models. However, all anatomical models showed satisfying accuracies and precisions, independent of the AM technology or part orientation. The anatomical and functional performance of FDM models was rated by surgeons as poor.

Minimal Detectable Bone Fracture Gaps in CT Images and Digital Three-Dimensional (3D) Radii Models.

Knowledge of the minimal detectable bone fracture gap is essential in three-dimensional (3D) models, particularly in pre-operative planning of osteosynthesis to avoid overlooking gaps. In this study, defined incisions and bony displacements ranging from 100 to 400 µm were created in diaphyseal radii in 20 paired forearm specimens and verified with light microscopy. The specimens were scanned utilizing different computed tomography (CT) technologies/scanners, specimen positionings, scan protocols, image segmentations, and processing protocols. Inter- and intra-operator variabilities were reported as coefficient kappa. In CT images, fracture gaps of 100 µm and bone lamellae of 300 µm and 400 µm width were identified at a rate of 80 to 100%, respectively, independent of the investigated settings. In contrast, only 400µm incisions and bony displacements were visible in digital 3D models, with detection rates dependent on CT technology, image segmentation, and post-processing algorithm. 3D bone models based on state-of-the-art CT imaging can reliably visualize clinically relevant bone fracture gap sizes. However, verification of fractures to be surgically addressed should be verified with the original CT image series.

Accuracy Analysis of 3D Bone Fracture Models: Effects of Computed Tomography (CT) Imaging and Image Segmentation.

The introduction of three-dimensional (3D) printed anatomical models has garnered interest in pre-operative planning, especially in orthopedic and trauma surgery. Identifying potential error sources and quantifying their effect on the model dimensional accuracy are crucial for the applicability and reliability of such models. In this study, twenty radii were extracted from anatomic forearm specimens and subjected to osteotomy to simulate a defined fracture of the distal radius (Colles' fracture). Various factors, including two different computed tomography (CT) technologies (energy-integrating detector (EID) and photon-counting detector (PCD)), four different CT scanners, two scan protocols (i.e., routine and high dosage), two different scan orientations, as well as two segmentation algorithms were considered to determine their effect on 3D model accuracy. Ground truth was established using 3D reconstructions of surface scans of the physical specimens. Results indicated that all investigated variables significantly impacted the 3D model accuracy (p < 0.001). However, the mean absolute deviation fell within the range of 0.03 ± 0.20 to 0.32 ± 0.23 mm, well below the 0.5 mm threshold necessary for pre-operative planning. Intra- and inter-operator variability demonstrated fair to excellent agreement for 3D model accuracy, with an intra-class correlation (ICC) of 0.43 to 0.92. This systematic investigation displayed dimensional deviations in the magnitude of sub-voxel imaging resolution for all variables. Major pitfalls included missed or overestimated bone regions during the segmentation process, necessitating additional manual editing of 3D models. In conclusion, this study demonstrates that 3D bone fracture models can be obtained with clinical routine scanners and scan protocols, utilizing a simple global segmentation threshold, thereby providing an accurate and reliable tool for pre-operative planning.

The role of the peroneal tendons in passive stabilisation of the ankle joint: an in vitro study.

PURPOSE: Peroneal tendons are known as active stabilizer in acute ankle sprain while an intact ankle mortise and intact lateral ligaments are required for passive stability of the ankle joint. The goal of this study is to determine the peroneal tendons as passive stabilizer in case of lateral ligament instability. METHODS: Twelve (12) human lower leg cadaver specimens underwent a torsion simulation in the testing system, 858 Mini Bionix(®) (MTS(®) Systems Corporation, Eden Prairie, MN, USA) and a specially designed mounting platform for the specimens. The preset torsion between tibia and calcaneus was primarily set at 30° of internal rotation during plantar flexion and hindfoot inversion. The resisting torque around mechanical tibial axis was recorded which ensures stability in ankle sprain trauma. The first series of measurements were performed on healthy specimens and the following after transecting structures in following order: ATFL (anterior talofibular ligament) in combination with CFL (calcaneofibular ligament), followed by peroneus longus tendon and finally peroneus brevis tendon. RESULTS: The combined lateral ATFL and CFL instability shows a decrease of the resisting torque which ensures stability in ankle sprain trauma. Only a transection of PLT with existing lateral dual-ligament instability results in a significant decrease in torque (p < 0.0001). CONCLUSION: The PLT has a substantial effect on passive stability at a present lateral ligament lesion in ankle sprain trauma. A deficiency in viscoelastic properties of the peroneus longus tendon must be considered in diagnostic and treatment for ankle instability.

Relative lateral wall thickness is an improved predictor for postoperative lateral wall fracture after trochanteric femoral fracture osteosynthesis.

Lateral wall thickness is a known predictor for postoperative stability of trochanteric femoral fractures and occurrence of secondary lateral wall fractures. Currently, the AO/OTA classification relies on the absolute lateral wall thickness (aLWT) to distinguish between stable A1.3 and unstable A2.1 fractures that does not take interpersonal patient differences into account. Thus, a more individualized and accurate measure would be favorable. Therefore, we proposed and validated a new patient-specific measure-the relative lateral wall thickness (rLWT)-to consider individualized measures and hypothesized its higher sensitivity and specificity compared with aLWT. First, in 146 pelvic radiographs of patients without a trochanteric femoral fracture, the symmetry of both caput-collum-diaphyseal angle (CCD) and total trochanteric thickness (TTT) was assessed to determine whether the contralateral side can be used for rLWT determination. Then, data of 202 patients were re-evaluated to compare rLWT versus previously published aLWT. Bilateral symmetry was found for both CCD and TTT (p ≥ 0.827), implying that bone morphology and geometry of the contralateral intact side could be used to calculate rLWT. Validation revealed increased accuracy of the rLWT compared with the gold standard aLWT, with increased specificity by 3.5% (Number Needed to Treat = 64 patients) and sensitivity by 1% (Number Needed to Treat = 75 patients). The novel rLWT is a more accurate and individualized predictor of secondary lateral wall fractures compared with the standard aLWT. This study established the threshold of 50.5% rLWT as a reference value for predicting fracture stability in trochanteric femoral fractures.

A biomechanical in-vitro study on an alternative fixation technique of the pubic symphysis for open book injuries of the pelvis.

PURPOSE: Implant failure rates remain high after plate fixation in pelvic ring injuries. The aim of this study was to compare an alternative fixation technique with suture-button devices and anterior plate fixation in partially stable open-book injuries. MATERIAL AND METHODS: We acquired 16 human fresh frozen anatomic pelvic specimens. The sacrospinous, sacrotuberous, and anterior sacroiliac ligaments were bilaterally released, and the pubic symphysis transected to simulate a partially stable open-book (AO/OTA 61-B3.1) injury. The specimens were randomly assigned to the two fixation groups. In the first group two suture-button devices were placed in a criss-crossed position through the symphysis. In second group a six-hole plate with standard 3.5 unlocked bicortical screws was used for fixation. Biomechanical testing was performed on a servo-hydraulic apparatus simulating bilateral stance, as described by Hearn and Varga. Cyclic compression loading with a progressively increasing peak load (0.5 N/cycle) was applied until failure. The failure mode, the load and the number of cycles at failure and the proximal and distal distance of the symphysis during testing were compared. RESULTS: There was no implant failure in either of the two groups. Failures occurred in nine pelvises (56.2%) at the fixation between the sacrum and the mounting jig and in seven pelvises (43.8%) in the sacroiliac joint. Neither the ultimate load nor the number of cycles at failure differed between the surgical techniques (p = 0.772; p = 0.788, respectively). In the suture button group the mean ultimate load was 874.5 N and the number of cycles at failure was 1907.9. In the plate group values were 826.1 N and 1805.6 cycles, respectively. No significant differences at proximal and distal diastasis of the symphysis were monitored during the whole loading process. CONCLUSION: The fixation with suture button implants showed comparable results to anterior plate fixation in open-book injuries of the pelvis.