RESUMEN
Halide perovskite solar cells (PSCs) have achieved power conversion efficiencies (PCEs) approaching 26%, however, the stability issue hinders their commercialization. Due to the soft ionic nature of perovskite materials, the strain effect on perovskite films has been recently recognized as one of the key factors that affects their opto-electronic properties and the device stability. Herein, we summarized the origins of strain, characterization techniques, and implications of strain on both perovskite film and solar cells as well as various strategies to control the strain. Finally, we proposed effective strategies for future strain engineering. We believe this comprehensive review could further facilitate researchers with a deeper understanding of strain effect and enhance the research activity in engineering the strain to further improve performance and especially the device stability toward commercialization.
RESUMEN
Chemical environment and precursor-coordinating molecular interactions within a perovskite precursor solution can lead to important implications in structural defects and crystallization kinetics of a perovskite film. Thus, the opto-electronic quality of such films can be boosted by carefully fine-tuning the coordination chemistry of perovskite precursors via controllable introduction of additives, capable of forming intermediate complexes. In this work, we employed a new type of ligand, namely 1-phenylguanidine (PGua), which coordinates strongly with the PbI2 complexes in the perovskite precursor, forming new intermediate species. These strong interactions effectively retard the perovskite crystallization process and form homogeneous films with enlarged grain sizes and reduced density of defects. In combination with an interfacial treatment, the resulted champion devices exhibit a 24.6% efficiency with outstanding operational stability. Unprecedently, PGua can be applied in various PSCs with different perovskite compositions and even in both configurations: n-i-p and p-i-n, highlighting the universality of this ligand.
RESUMEN
While perovskite photovoltaic (PV) devices are on the verge of commercialization, promising methods to recycle or remanufacture fully encapsulated perovskite solar cells (PSCs) and modules are still missing. Through a detailed life-cycle assessment shown in this work, we identify that the majority of the greenhouse gas emissions can be reduced by re-using the glass substrate and parts of the PV cells. Based on these analytical findings, we develop a novel thermally assisted mechanochemical approach to remove the encapsulants, the electrode, and the perovskite absorber, allowing reuse of most of the device constituents for remanufacturing PSCs, which recovered nearly 90% of their initial performance. Notably, this is the first experimental demonstration of remanufacturing PSCs with an encapsulant and an edge-seal, which are necessary for commercial perovskite solar modules. This approach distinguishes itself from the "traditional" recycling methods previously demonstrated in perovskite literature by allowing direct reuse of bulk materials with high environmental impact. Thus, such a remanufacturing strategy becomes even more favorable than recycling, and it allows us to save up to 33% of the module's global warming potential. Remarkably, this process most likely can be universally applied to other PSC architectures, particularly n-i-p-based architectures that rely on inorganic metal oxide layers deposited on glass substrates. Finally, we demonstrate that the CO2-footprint of these remanufactured devices can become less than 30 g/kWh, which is the value for state-of-the-art c-Si PV modules, and can even reach 15 g/kWh assuming a similar lifetime.
RESUMEN
The stabilization of grain boundaries and surfaces of the perovskite layer is critical to extend the durability of perovskite solar cells. Here we introduced a sulfonium-based molecule, dimethylphenethylsulfonium iodide (DMPESI), for the post-deposition treatment of formamidinium lead iodide perovskite films. The treated films show improved stability upon light soaking and remains in the black α phase after two years ageing under ambient condition without encapsulation. The DMPESI-treated perovskite solar cells show less than 1% performance loss after more than 4,500 h at maximum power point tracking, yielding a theoretical T80 of over nine years under continuous 1-sun illumination. The solar cells also display less than 5% power conversion efficiency drops under various ageing conditions, including 100 thermal cycles between 25 °C and 85 °C and an 1,050-h damp heat test.
RESUMEN
A sacrificial film of polystyrene nanoparticles was utilized to introduce nano-cavities into mesoporous metal oxide layers. This enabled the growth of larger perovskite crystals inside the oxide scaffold with significantly suppressed non-radiative recombination and improved device performance. This work exemplifies potential applications of such nanoarchitectonic approaches in perovskite opto-electronic devices.
RESUMEN
Tremendous efforts have been dedicated toward minimizing the open-circuit voltage deficits on perovskite solar cells (PSCs), and the fill factors are still relatively low. This hinders their further application in large scalable modules. Herein, we employ a newly designed ammonium salt, cyclohexylethylammonium iodide (CEAI), for interfacial engineering between the perovskite and hole-transporting layer (HTL), which enhanced the fill factor to 82.6% and consequent PCE of 23.57% on the target device. This can be associated with a reduction of the trap-assisted recombination rate at the 3D perovskite surface, via formation of a 2D perovskite interlayer. Remarkably, the property of the 2D perovskite interlayer along with the cyclohexylethyl group introduced by CEAI treatment also determines a pronounced enhancement in the surface hydrophobicity, leading to an outstanding stability of over 96% remaining efficiency of the passivated devices under maximum power point tracking with one sun illumination under N2 atmosphere at room temperature after 1500 h.
RESUMEN
The electrically insulating space layer takes a fundamental role in monolithic carbon-graphite based perovskite solar cells (PSCs) and it has been established to prevent the charge recombination of electrons at the mp-TiO2/carbon-graphite (CG) interface. Thick 1 µm printed layers are commonly used for this purpose in the established triple-mesoscopic structures to avoid ohmic shunts and to achieve a high open circuit voltage. In this work, we have developed a reproducible large-area procedure to replace this thick space layer with an ultra-thin dense 40 nm sputtered Al2O3 which acts as a highly electrically insulating layer preventing ohmic shunts. Herewith, transport limitations related so far to the hole diffusion path length inside the thick mesoporous space layer have been omitted by concept. This will pave the way toward the development of next generation double-mesoscopic carbon-graphite-based PSCs with highest efficiencies. Scanning electron microscope, energy dispersive X-ray analysis, and atomic force microscopy measurements show the presence of a fully oxidized sputtered Al2O3 layer forming a pseudo-porous covering of the underlying mesoporous layer. The thickness has been finely tuned to achieve both electrical isolation and optimal infiltration of the perovskite solution allowing full percolation and crystallization. Photo voltage decay, light-dependent, and time-dependent photoluminescence measurements showed that the optimal 40 nm thick Al2O3 not only prevents ohmic shunts but also efficiently reduces the charge recombination at the mp-TiO2/CG interface and, at the same time, allows efficient hole diffusion through the perovskite crystals embedded in its pseudo-pores. Thus, a stable V OC of 1 V using CH3NH3PbI3 perovskite has been achieved under full sun AM 1.5 G with a stabilized device performance of 12.1%.