Encapsulation of Uranium Oxide in Multiwall WS2 Nanotubes.

Uranium is a high-value energy element, yet also poses an appreciable environmental burden. The demand for a straightforward, low energy, and environmentally friendly method for encapsulating uranium species can be beneficial for long-term storage of spent uranium fuel and a host of other applications. Leveraging on the low melting point (60 °C) of uranyl nitrate hexahydrate and nanocapillary effect, a uranium compound is entrapped in the hollow core of WS2 nanotubes. Followingly, the product is reduced at elevated temperatures in a hydrogen atmosphere. Nanocrystalline UO2 nanoparticles anchor within the WS2 nanotube lumen are obtained through this procedure. Such methodology can find utilization in the processing of spent nuclear fuel or other highly active radionuclides as well as a fuel for deep space missions. Moreover, the low melting temperatures of different heavy metal-nitrate hydrates, pave the way for their encapsulation within the hollow core of the WS2 nanotubes, as demonstrated herein.

Size Dependence of Lattice Parameter and Electronic Structure in CeO2 Nanoparticles.

Intrinsic properties of a compound (e.g., electronic structure, crystallographic structure, optical and magnetic properties) define notably its chemical and physical behavior. In the case of nanomaterials, these fundamental properties depend on the occurrence of quantum mechanical size effects and on the considerable increase of the surface to bulk ratio. Here, we explore the size dependence of both crystal and electronic properties of CeO2 nanoparticles (NPs) with different sizes by state-of-the art spectroscopic techniques. X-ray diffraction, X-ray photoelectron spectroscopy, and high-energy resolution fluorescence-detection hard X-ray absorption near-edge structure (HERFD-XANES) spectroscopy demonstrate that the as-synthesized NPs crystallize in the fluorite structure and they are predominantly composed of CeIV ions. The strong dependence of the lattice parameter with the NPs size was attributed to the presence of adsorbed species at the NPs surface thanks to Fourier transform infrared spectroscopy and thermogravimetric analysis measurements. In addition, the size dependence of the t2g states in the Ce LIII XANES spectra was experimentally observed by HERFD-XANES and confirmed by theoretical calculations.

Alginate Hydrogels: A Tool for 3D Cell Encapsulation, Tissue Engineering, and Biofabrication.

A wide variety of hydrogels have been proposed for tissue engineering applications, cell encapsulation, and bioinks for bioprinting applications. Cell-laden hydrogel constructs rely on natural hydrogels such as alginate, agarose, chitosan, collagen, gelatin, fibroin, and hyaluronic acid (HA), as well as on synthetic hydrogels such as poloxamers (Pluronics®) and polyethylene glycol (PEG). Alginate has become more and more important in the last years, thanks to the possibility to prepare alginate hydrogels suitable for cell encapsulation mainly because of the mild and reversible cross-linking conditions. In this paper alginate will be described in detail with respect to its chemistry, cross-linking behavior, biocompatibility, manufacturing capacity, and possible modifications.

Natural Origin Materials for Osteochondral Tissue Engineering.

Materials selection is a critical aspect for the production of scaffolds for osteochondral tissue engineering. Synthetic materials are the result of man-made operations and have been investigated for a variety of tissue engineering applications. Instead, the products of physiological processes and the metabolic activity of living organisms are identified as natural materials. Over the recent decades, a number of natural materials, namely, biopolymers and bioceramics, have been proposed as the main constituent of osteochondral scaffolds, but also as cell carriers and signaling molecules. Overall, natural materials have been investigated both in the bone and in the cartilage compartment, sometimes alone, but often in combination with other biopolymers or synthetic materials. Biopolymers and bioceramics possess unique advantages over their synthetic counterparts due similarity with natural extracellular matrix, the presence of cell recognition sites and tunable chemistry. However, the characteristics of natural origin materials can vary considerably depending on the specific source and extraction process. A deeper understanding of the relationship between material variability and biological activity and the definition of standardized manufacturing procedures will be crucial for the future of natural materials in tissue engineering.

The effects of Bombyx mori silk strain and extraction time on the molecular and biological characteristics of sericin.

Sericin was extracted from three strains of Thai Bombyx mori silk cocoons (white shell Chul1/1, greenish shell Chul3/2, and yellow shell Chul4/2) by a high-pressure and high-temperature technique. The characteristics of sericin extracted from different fractions (15, 45, and 60 min extraction process) were compared. No differences in amino acid composition were observed among the three fractions. For all silk strains, sericin extracted from a 15-min process presented the highest molecular weight. The biological potential of the different sericin samples as a bioadditive for 3T3 fibroblast cells was assessed. When comparing sericin extracted from three silk strains, sericin fractions extracted from Chul4/2 improved cell proliferation, while sericin from Chul 1/1 activated Type I collagen production to the highest extent. This study allows the natural variability of sericin obtained from different sources and extraction conditions to be addressed and provides clues for the selection of sericin sources.

A combined method for bilayered vascular graft fabrication.

Autologous saphenous vein is still the conduit of choice for peripheral by-pass. Synthetic vascular grafts in polyethylene terephthalate and expanded polytetrafluoroethylene are used if vein access cannot be obtained. However they are successfully used to replace large diameter vessels, but they fail in small diameters (<6 mm). In the present study a bilayered synthetic vascular graft was developed. The graft was composed of an inner nanofibrous layer obtained by electrospinning able to host endothelial cells and a highly porous external layer obtained by spray, phase-inversion technique capable to sustain tunica media regeneration. Graft morphology and thickness, fiber size, pore size and layer adhesion strength were assessed. The innovative combination of two different consolidated techniques allowed to manufacture a nanostructured composite graft featuring a homogeneous microporous layer firmly attached on the top of the electrospun layer. By tuning the mechanical properties and the porosity of vascular prostheses, it will be possible to optimize the graft for in situ tissue regeneration while preventing blood leakage.

Biomolecule gradient in micropatterned nanofibrous scaffold for spatiotemporal release.

Controlled molecule release from scaffolds can dramatically increase the scaffold ability of directing tissue regeneration in vitro and in vivo. Crucial to the regeneration is precise regulation over release direction and kinetics of multiple molecules (small genes, peptides, or larger proteins). To this end, we developed gradient micropatterns of electrospun nanofibers along the scaffold thickness through programming the deposition of heterogeneous nanofibers of poly(ε-caprolactone) (PCL) and poly(D,L-lactide-co-glycolide) acid (PLGA). Confocal images of the scaffolds containing fluorophore-impregnated nanofibers demonstrated close matching of actual and designed gradient fiber patterns; thermal analyses further showed their matching in the composition. Using acid-terminated PLGA (PLGAac) and ester-terminated PLGA (PLGAes) to impregnate molecules in the PCL-PLGA scaffolds, we demonstrated for the first time their differences in nanofiber degeneration and molecular weight change during degradation. PLGAac nanofibers were more stable with gradual and steady increase in the fiber diameter during degradation, resulting in more spatially confined molecule delivery from PCL-PLGA scaffolds. Thus, patterns of PCL-PLGAac nanofibers were used to design versatile controlled delivery scaffolds. To test the hypothesis that molecule-impregnated PLGAac in the gradient-patterned PCL-PLGAac scaffolds can program various modalities of molecule release, model molecules, including small fluorophores and larger proteins, were respectively used for time-lapse release studies. Gradient-patterns were used as building blocks in the scaffolds to program simultaneous release of one or multiple proteins to one side or, respectively, to the opposite sides of scaffolds for up to 50 days. Results showed that the separation efficiency of molecule delivery from all the scaffolds with a thickness of 200 µm achieved >88% for proteins and >82% for small molecules. In addition to versatile spatially controlled delivery, micropatterns were designed to program sequential release of proteins. The hierarchically structured materials presented here may enable development of novel multifunctional scaffolds with defined 3D dynamic microenvironments for tissue regeneration.

Development of alginate-based hydrogels for blood vessel engineering.

Vascular diseases are among the primary causes of death worldwide. In serious conditions, replacement of the damaged vessel is required. Autologous grafts are preferred, but their limited availability and difficulty of the harvesting procedures favour synthetic alternatives' use. However, as synthetic grafts may present significant drawbacks, tissue engineering-based solutions are proposed. Herein, tubular hydrogels of alginate combined with collagen type I and/or silk fibroin were prepared by ionotropic gelation using gelatin hydrogel sacrificial moulds loaded with calcium ions (Ca2+). The time of exposure of alginate solutions to Ca2+-loaded gelatin was used to control the wall thickness of the hydrogels (0.47 ± 0.10 mm-1.41 ± 0.21 mm). A second crosslinking step with barium chloride prevented their degradation for a 14 day period and improved mechanical properties by two-fold. Protein leaching tests showed that collagen type I, unlike silk fibroin, was strongly incorporated in the hydrogels. The presence of silk fibroin in the alginate matrix, containing or not collagen, did not significantly improve hydrogels' properties. Conversely, hydrogels enriched only with collagen were able to better support EA.hy926 and MRC-5 cells' growth and characteristic phenotype. These results suggest that a two-step crosslinking procedure combined with the use of collagen type I allow for producing freestanding vascular substitutes with tuneable properties in terms of size, shape and wall thickness.

Analysis of oxidative degradation and calcification behavior of a silicone polycarbonate polyurethane-polydimethylsiloxane material.

The biocompatibility and chemical stability of implantable devices are crucial for their long-term success. CarboSil® is a silicon polycarbonate polyurethane copolymer with good biocompatibility and biostability properties. Here, we explored the possibility to improve these characteristics by introducing 30% of extra-chain cross-linkable poly(dimethyl siloxane) (PDMS). Patches made of CarboSil and CarboSil-30% PDMS were manufactured by spray, phase-inversion technique and subjected to a heating-pressure treatment. Both materials showed good biocompatibility, either in viability and proliferation of cell-based experiments both with mouse fibroblasts and subcutaneous implant in rats. Fourier-transform infrared spectroscopy showed a significant decrease in soft segment loss in CarboSil-30% PDMS samples with respect to CarboSil in in vitro accelerated oxidative treatments with CoCl2 and 20% H2 O2 at 37°C up to 36 days. Same results were observed in subcutaneous implants up to 90 days. Field-emission scanning electron microscopy on samples exposed to calcification solutions during 80 days highlighted the presence of a homogeneous distribution of calcium deposition over the entire surface of CarboSil samples, while no calcium deposits were observed in CarboSil-30% PDMS samples. Patches subjected to subcutaneous experiments showed no sign of calcification after 90 days, irrespectively of their composition. Thanks to the improved characteristics in terms of degradation and calcification the modified materials described in this work hold great promise for their use in the manufacture of cardiovascular devices.

Microfluidic-assisted electrospinning, an alternative to coaxial, as a controlled dual drug release system to treat inflammatory arthritic diseases.

Inflammatory arthritic diseases are characterized by a persistent inflammation of the synovial tissues where tumor necrosis factor alpha (TNFα) and interleukin-6 (IL-6) pro-inflammatory cytokines are over-expressed, leading to progressive musculoskeletal disability. Methotrexate (MTX), a disease-modifying-anti-rheumatic drug (DMARD) commonly applied in their treatment, can be used in combination with biological-DMARDs as anti-TNFα antibody to improve the treatments efficacy. However, their systemic administration comes with severe side-effects and limited therapeutic efficacy due to their off-target distribution and short half-life. To overcome such limitations, encapsulation of clinically relevant concentrations of MTX and anti-TNFα antibody into polycaprolactone (PCL) or poly(vinyl-alcohol) (PVA) microfluidic-assisted or coaxial electrospun fibrous meshes is proposed as local controlled dual drug release systems. Release studies show that microfluidic-assisted electrospinning meshes encapsulating both drugs achieved higher concentrations than coaxials. Biological assays using human articular chondrocytes (hACs) and monocytic cells (THP-1 cell line) demonstrate that fibrous meshes encapsulating the drugs are non-toxic. The systems' efficacy is proved by a significant decrease of TNFα and IL-6 concentrations in conditioned medium of lipopolysaccharide (LPS)-stimulated THP-1 cells, especially in the presence of microfluidic-assisted electrospun meshes, when compared with THP-1 conditioned medium (59.5% and 83.9% less, respectively). Therefore, microfluidic-assisted electrospinning fibrous meshes with encapsulating drugs represent an alternative to coaxial, as a local therapy for inflammatory arthritis diseases.

Recovery of rare earth elements by nanometric CeO2 embedded into electrospun PVA nanofibres.

Rare earth elements (REEs) are critical raw materials with a wide range of industrial applications. As a result, the recovery of REEs via adsorption from REE-rich matrices, such as water streams from processed electric and electronic waste, has gained increased attention for its simplicity, cost-effectiveness and high efficacy. In this work, the potential of nanometric cerium oxide-based materials as adsorbents for selected REEs is investigated. Ultra-small cerium oxide nanoparticles (CNPs, mean size diameter ≈ 3 nm) were produced via a precipitation-hydrothermal procedure and incorporated into woven-non-woven polyvinyl alcohol (PVA) nanofibres (d ≈ 280 nm) via electrospinning, to a final loading of ≈34 wt%. CNPs, CNP-PVA and the benchmark material CeO2 NM-212 (JRCNM02102, mean size diameter ≈ 28 nm) were tested as adsorbents for aqueous solutions of the REEs Eu3+, Gd3+ and Yb3+ at pH 5.8. Equilibrium adsorption data were interpreted by means of Langmuir and Freundlich data models. The maximum adsorption capacities ranged between 16 and 322 mgREE gCeO2 -1, with the larger value found for the adsorption of Yb3+ by CNP. The trend of maximum adsorption capacity was CNPs > NM-212 > CNP-PVA, which was ascribed to different agglomeration and surface area available for adsorption. Langmuir equilibrium constants K L were substantially larger for CNP-PVA, suggesting a potential higher affinity of REEs for CNPs due to a synergistic effect of PVA on adsorption. CNP-PVA were effectively used in repeated adsorption cycles under static and dynamic configurations and retained the vast majority of adsorptive material (>98% of CeO2 retained after 10 adsorption cycles). The small loss was attributed to partial solubilisation of fibre components with change in membrane morphology. The findings of this study pave the way for the application of CNP-PVA nanocomposites in the recovery of strategically important REEs from electrical and electronic waste.

Fibroin and Polyvinyl Alcohol Hydrogel Wound Dressing Containing Silk Sericin Prepared Using High-Pressure Carbon Dioxide.

Objective: To fabricate and investigate the properties of fibroin and polyvinyl alcohol (PVA) hydrogels containing sericin prepared using high-pressure carbon dioxide (CO2). Approach: In this study, fibroin/PVA hydrogels with and without sericin were prepared using the high-pressure CO2 method. The physical and mechanical properties of the hydrogels were investigated using field-emission scanning electron microscopy, Fourier-transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry, and the swelling, water retention, and compressive properties were assessed. Results: The hydrogels obtained from the combination of fibroin and PVA presented a compositional gradient along the hydrogel thickness and structure. The upper layer of the hydrogel consisted of a fibroin-based hydrogel blended with PVA, whereas the lower layer contained only fibroin. The mechanical properties regarding compression of the fibroin/PVA hydrogel were significantly better than those of the pure fibroin hydrogel, for hydrogels with and without sericin. Moreover, the mechanical properties of the hydrogels with sericin were significantly better than those without sericin. The water contents of all samples were >90%. Innovation: This study assessed a new combination of a wound healing agent and a biomaterial dressing. Moreover, this hydrogel production technique used a clean method without the need for a chemical crosslinking agent. Conclusion: The combination of the fibroin and PVA hydrogel and sericin prepared using the high-pressure CO2 method led to good physical properties. This material may be a candidate for medical applications.

Hydrogen sulfide-releasing silk fibroin scaffold for bone tissue engineering.

Hydrogen sulfide (H2S)-based therapy is a promising therapeutic strategy for several biomedical applications. Following the observation that endogenous and exogenous H2S plays a prominent role as a bone anabolic agent, we recently developed a silk fibroin (SF) porous scaffold loaded with GYY4137 (GYY), an H2S donor, for applications in bone tissue engineering. Here, we assayed whether the combination of SF with H2S potentiates the osteoconductive properties of SF. Biocompatibility and osteoanabolic activity were assayed in vitro using human bone marrow mesenchymal stromal cells. Cell cultures were performed on a perfusion bioreactor to obtain results closer to the in vivo microenvironment. Cytotoxicity was excluded by lactate dehydrogenase and live/dead assays. Cell colonization and mineral apposition were evaluated by Haematoxylin & Eosin and Von Kossa/Alizarin Red-S stainings respectively. PCR array for human osteogenesis and immunohistochemical analyses were performed to identify pathways and targets involved. Our findings show that H2S-releasing SF scaffolds supported cell adhesion, proliferation and viability. Moreover, H2S activated genes and proteins involved in ossification, osteoblast differentiation, bone mineral metabolism and angiogenesis allowing a high and early mineralization. Based on these properties, we suggest the use of H2S-releasing SF scaffolds for bone healing and regeneration applications.

Coaxial PCL/PEG-thiol-ene microfiber with tunable physico-chemical properties for regenerative scaffolds.

Tissue regeneration requires scaffolds that exhibit mechanical properties similar to the tissues to be replaced while allowing cell infiltration and extracellular matrix production. Ideally, the scaffolds' porous architecture and physico-chemical properties can be precisely defined to address regenerative needs. We thus developed techniques to produce hybrid fibers coaxially structured with a polycaprolactone core and a 4-arm, polyethylene glycol thiol-norbornene sheath. We assessed the respective effects of crosslink density and sheath polymer size on the scaffold architecture, physical and mechanical properties, as well as cell-scaffold interactions in vitro and in vivo. All scaffolds displayed high elasticity, swelling and strength, mimicking soft tissue properties. Importantly, the thiol-ene hydrogel sheath enabled tunable softness and peptide tethering for cellular activities. With increased photopolymerization, stiffening and reduced swelling of scaffolds were found due to intra- and inter-fiber crosslinking. More polymerized scaffolds also enhanced the cell-scaffold interaction in vitro and induced spontaneous, deep cell infiltration to produce collagen and elastin for tissue regeneration in vivo. The molecular weight of sheath polymer provides an additional mechanism to alter the physical properties and biological activities of scaffolds. Overall, these robust scaffolds with tunable elasticity and regenerative cues offered a versatile and effective platform for tissue regeneration.

Silk fibroin porous scaffolds by N2O foaming.

Silk fibroin has acquired increasing interest for biomedical applications, and namely for the fabrication of scaffolds for tissue engineering, because of its highly positive biological interaction and the possibility to adapt the material to several application requirements by adopting different fabrication methods, in order to make films, sponges, fibers, nets or gels with predictable degradation times. For tissue engineering, in most cases porous scaffolds are required, in some cases possibly in situ forming and therefore fabricated in mild body-compatible conditions. In this work, we present a novel one-step method for the preparation of silk fibroin foams starting from water solutions and using low-pressure nitrous oxide gas as foaming agent. This foaming technique allows preparing fibroin porous scaffolds with easily tunable porosity, in mild processing conditions with the use of a relatively inert foaming agent saturating a fibroin water solution, that could be occasionally injected through a thin needle in the implantation site where expansion and foaming would occur. Optimal foaming processing conditions have been investigated, and the prepared foams have been characterized with Fourier Transform Infrared Spectroscopy (FTIR) compressive mechanical and rheological properties measurements, and by scanning electron microscopy and microCT.

Bioactivity and mineralization of natural hydroxyapatite from cuttlefish bone and Bioglass® co-sintered bioceramics.

In this study, bioactive hydroxyapatite (HAP)-based bioceramics starting from cuttlefish bone powders have been prepared and characterized. In particular, fragmented cuttlefish bone was co-sintered with 30 wt% of Bioglass® -45S5 to synthesize HAP-based powders with enhanced mechanical properties and bioactivity. Commercial synthetic HAP was treated following the same procedure and used as a reference. The structure and composition of the bioceramics formulations were characterized using Fourier transform infrared spectroscopy, X-ray diffraction and scanning electron microscopy. After the thermal treatment of cuttlefish bone powder added with 30 wt% Bioglass, new phases with compositions of sodium calcium phosphate [Na3 Ca6 (PO4 )5 ], ß-tricalcium phosphate [Ca3 (PO4 )] and amorphous silica were detected. In vitro cell culture studies were performed by evaluating proliferation, metabolic activity and differentiation of human osteoblast-like cells (MG63). Scaffolds made with cuttlefish bone powder exhibited increased apatite deposition, alkaline phosphatase activity and cell proliferation compared with commercial synthetic HAP. In addition, the ceramic compositions obtained after the combination with Bioglass® further enhanced the metabolic activity of MG63 cell and promoted the formation of a well-developed apatite layer after 7 days of incubation in Dulbecco's modified Eagle's medium.

Enhancing bioactive properties of silk fibroin with diatom particles for bone tissue engineering applications.

Many studies have highlighted the role of silicon in human bone formation and maintenance. Silicon, in fact, is considered to nucleate the precipitation of hydroxyapatite and to reduce the bone resorption. For this reason, we have combined silk fibroin (SF) with silicon-releasing diatom particles (DPs), as potential material for bone tissue engineering applications. Sponges of fibroin loaded with different amounts and sizes of DPs were prepared by solvent casting-particulate leaching method, and their morphology, porosity and mechanical properties were evaluated. The biological effect of diatom addition was assessed on human osteosarcoma cell line MG63, a suitable osteoblast-like model, through cell adhesion, metabolic activity and proliferation assays. In addition, alkaline phosphatase activity, osterix and collagen type I production in MG63 cell line were assessed as markers of early bone formation to demonstrate a pro-mineralization potential of scaffolds. Results of the studies showed that addition to fibroin of diatoms particles improved the osteogenic properties of osteoblast-like cells compared with the pure SF. Copyright © 2016 John Wiley & Sons, Ltd.

Effect of Cryopreservation on Cell-Laden Hydrogels: Comparison of Different Cryoprotectants.

Cell encapsulation in hydrogels is a technique that offers a variety of applications, ranging from drug delivery to biofabrication of three-dimensional scaffolds. The assembly of cell-laden hydrogel building blocks aims to generate complex biological constructs by manipulating microscale units. An important issue for the clinical implementation of this technique is the long-term storage of a large stock of cell/hydrogel building blocks. In this work, the impact of cryopreservation on the viability and functionality of cells encapsulated in alginate matrices is presented comparing different cryoprotective agents (CPAs). Human osteosarcoma MG63 cells were encapsulated in sodium alginate fiber constructs with wetspinning method and exposed to different formulations of cryopreservation media, containing dimethyl sulfoxide (DMSO), glycerol, and trehalose. The cell-laden fibers were subsequently slow-cooled down to -80°C and stored in liquid nitrogen. After thawing, viability and death pathway of encapsulated cells were investigated, and metabolic activity and proliferative capacity of cells released from the alginate matrix were evaluated. The viability of MG63 cells encapsulated in alginate matrix ranged from 71% ± 4% to 85% ± 2%, depending on the cryoprotective media formulation with no protracted harmful effects from the CPAs. On the other side, cells cryopreserved in encapsulated conditions and released from the hydrogel showed larger metabolic activity and proliferative capacity in tissue culture plate compared to cells cryopreserved in suspension, in particular when DMSO and glycerol were used as CPAs. Results have been correlated with the viscoelastic properties and water content changes of the alginate constructs loaded with the different CPAs.

Sodium oleate induced rapid gelation of silk fibroin.

Silk fibroin has acquired increasing interest in the last years for application in medicine and namely in tissue engineering. Several methods have been developed to process fibroin and for the fabrication of nets, sponges, films and gels. This paper deals with the fabrication and characterization of fibroin hydrogels obtained by using sodium oleate as gelation agent. Gels have been prepared by mixing Silk fibroin (SF) and Sodium oleate (SO) water solutions in different concentrations, and a quite wide frame of compositions have been explored. Rheological tests have been performed to determine the gelation times, scanning electron microscopies have been made to evaluate morphologies, FTIR analysis has been done to determine the conformation of the starting materials and of the resulting gels, water content has been measured and cytotoxicity tests have been performed to validate the potential biomedical use of the hydrogels. Depending on the SF and SO different gelation times have been obtained thanks to the formation of intermolecular bonds between the fibroin chains. The obtained fastest gelation of about 80 s could make this specific formulation compatible with in situ gelation. By changing composition, gels with different morphologies, rheological properties and water contents have been prepared.

Silk Fibroin Porous Scaffolds Loaded with a Slow-Releasing Hydrogen Sulfide Agent (GYY4137) for Applications of Tissue Engineering.

Hydrogen sulfide (H2S) is a physiological gasotransmitter known to possess a regulatory role in several tissues, including bone. The exogenous administration by injection of solutions of H2S-releasing compounds (e.g., GYY4137) has been previously investigated as a novel therapeutic approach for the treatment of bone diseases. Here, GYY4137 was embedded into fibroin sponges, previously shown to be suitable as scaffolds for bone, thanks to their biocompatibility, scalable porous structure, and biodegradability rate. Fibroin porous scaffolds were produced by solvent casting and the particulate leaching method, and GYY4137 was successively incorporated by using dimethyl sulfoxide (DMSO) as vehicle. The process used to produce GYY4137-loaded scaffolds allowed the incorporation of different controlled amounts of GYY4137 into fibroin matrices. The loading process preserved the properties of the system components in the final products, as assessed by SEM, FT-IR, NMR, and different thermal analyses techniques. Release of H2S from GYY4137 incorporated into the scaffolds was monitored upon incubation in saline solution at physiological pH: H2S-release kinetic was found to be dependent on the amount of GYY4137. To ensure biocompatibility, mouse fibroblasts and human primary bone marrow stromal cells were seeded onto scaffolds, and short-term viability assays were performed. Results showed that the GYY4137-loaded scaffold did not induce cytotoxicity in any of the cell type tested. Our findings demonstrate that embedding an H2S-releasing donor in silk fibroin scaffold is a suitable strategy to achieve a long-lasting release of H2S that preserves cell viability and allows local delivery at sites of tissue injury.