QCM-D and XPS study of protein adsorption on plasma polymers with sulfonate and phosphonate surface groups.

As some proteins are known to interact with sulfated and phosphated biomolecules such as specific glycosaminoglycans, this study derives from the hypothesis that sulfonate and phosphonate groups on solid polymer surfaces might cause specific interfacial interactions. Such surfaces were prepared by plasma polymerization of heptylamine (HA) and subsequent grafting of sulfonate or phosphonate groups via Michael-type addition of vinylic compounds. Adsorption of the proteins fibrinogen, albumin (HSA) and lysozyme on these functionalised plasma polymer surfaces was studied by XPS and quartz crystal microbalance with dissipation (QCM-D). It was also studied whether pre-adsorption with HSA would lead to a passivated surface against further adsorption of other proteins. XPS confirmed grafting of vinyl sulfonate and vinyl phosphonate onto the amine surface and showed that the proteins adsorbed to saturation at between 1 and 2 h. QCM-D showed rapid and irreversible adsorption of albumin on all three surfaces, while lysozyme could be desorbed with PBS to substantial extents from the sulfonated and phosphonated surfaces but not from the amine surface. Fibrinogen showed rapid initial adsorption followed by slower additional mass gain over hours. Passivation with albumin led to small and largely reversible subsequent adsorption of lysozyme, whereas with fibrinogen partial displacement yielded a mixed layer, regardless of the surface chemistry. Thus, protein adsorption onto these sulfonated and phosphonated surfaces is complex, and not dominated by electrostatic charge effects.

Solvent-induced porosity in ultrathin amine plasma polymer coatings.

Plasma polymers deposited from n-heptylamine onto silicon wafers have been found to form a porous microstructure when immersed in water and other solvents, with pores of dimensions and densities that vary considerably between coatings deposited under different plasma conditions. This solvent-induced pore formation was found to correlate with the observed percentage of extractable material. With low radio frequency (rf) power inputs, the resultant softer coatings possess considerably more extractable material than coatings deposited at higher applied power levels. The porosity is thus proposed to result from the formation of voids created by the extraction of soluble low-molecular-weight polymeric material, which produces shrinkage stress that the coating, firmly attached to the substrate, cannot relieve by macroscopic contraction. The microscopic contraction of plasma polymer volume creates voids that appear to span the entire film thickness. The effect of aging plasma polymers in air was also investigated. For films deposited at low power it led to reduced extraction of soluble material and different pore morphology, whereas for films deposited at higher rf power levels, the extracted amounts and pore formation were the same for aged coatings. It was also found that the density of surface amine groups was lower for films deposited under the two lowest power settings, in contrast to the commonly held belief that the use of minimal applied rf power aids retention of functional groups. These porous plasma polymer coatings with surface groups suitable for further interfacial chemical immobilization reactions may be useful for various membrane and biotechnology applications.

[The characteristic IR spectra of microcystin-LR].

The IR spectra of mincrocystin-LR (mLR) were studied by Fourier transform infrared spectroscopy in the scanning range of 4,000-600 cm(-1). The characteristic IR spectra from main function groups such as monosubstituted benzene, guanidine residues and gamma-carboxylic groups etc have been identified.

Sodium stearate adsorption onto titania pigment.

The interaction of sodium stearate with titania pigment particles from aqueous suspension has been investigated using thermal analysis and infrared spectroscopy combined with electrochemical studies. Thermogravimetric analysis (TGA) was used both to determine the adsorption isotherm and to investigate the interaction behavior. Monolayer coverage is determined to be 0.95 mg/m(2); however, unlike the case with organic solvents, multilayer adsorption occurs. Diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, combined with TGA, revealed that the surface monolayer is chemically bound. DRIFT spectroscopic data also indicated that the stearate bridged across two aluminum atoms. Subsequent stearate layers were physisorbed to the stearate monolayer and were readily removed with acetone washing.

Steric and electrostatic surface forces on sulfonated PEG graft surfaces with selective albumin adsorption.

Addition of ionized terminal groups to PEG graft layers may cause additional interfacial forces to modulate the net interfacial interactions between PEG graft layers and proteins. In this study we investigated the effect of terminal sulfonate groups, characterizing PEG-aldehyde (PEG-CHO) and sulfonated PEG (PEG-SO3) graft layers by XPS and colloid probe AFM interaction force measurements as a function of ionic strength, in order to determine surface forces relevant to protein resistance and models of bio-interfacial interaction of such graft coatings. On the PEG-CHO surface the measured interaction force does not alter with ionic strength, typical of a repulsive steric barrier coating. An analogous repulsive interaction force of steric origin was also observed on the PEG-SO3 graft coating; however, the net interaction force changed with ionic strength. Interaction forces were modelled by steric and electrical double layer interaction theories, with fitting to a scaling theory model enabling determination of the spacing and stretching of the grafted chains. Albumin, fibrinogen, and lysozyme did not adsorb on the PEG-CHO coating, whereas the PEG graft with terminal sulfonate groups showed substantial adsorption of albumin but not fibrinogen or lysozyme from 0.15 M salt solutions. Under lower ionic strength conditions albumin adsorption was again minimized as a result of the increased electrical double-layer interaction observed with the PEG-SO3 modified surface. This unique and unexpected adsorption behaviour of albumin provides an alternative explanation to the "negative cilia" model used by others to rationalize observed thromboresistance on PEG-sulfonate coatings.

PEGylation of porous silicon using click chemistry.

Porous silicon has received considerable interest in recent years in a range of biomedical applications, with its performance determined by surface chemistry. In this work, we investigate the PEGylation of porous silicon wafers using click chemistry. The porous silicon wafer surface chemistry was monitored at each stage of the reaction via photoacoustic Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy, whereas sessile drop contact angle and model protein adsorption measurements were used to characterize the final PEGylated surface. This work highlights the simplicity of click-chemistry-based functionalization in tailoring the porous silicon surface chemistry and controlling protein-porous silicon interactions.

TOF-SIMS and principal component analysis characterization of the multilayer surface grafting of small molecules: antibacterial furanones.

Furanone compounds (fimbrolides) have attracted interest as antibacterial compounds for use in human health care, for instance, as an antibacterial coating for medical devices to combat device-centered infections. To ensure effectiveness for extended periods of time, they must be immobilized covalently onto a device surface; in this study, this was done via azide/nitrene chemistry and photochemical coupling. However, the detection and quantification of surface-immobilized small molecules such as furanones presents a considerable analytical challenge, yet is necessary for optimization of coatings and reliable interpretation of biological responses. We have utilized the surface sensitivity and chemical specificity of time-of-flight secondary ion mass spectrometry (TOF-SIMS) to characterize each step of the grafting sequence. On account of the complexity of the data, principal component analysis (PCA) was used to interpret and compare spectra. The results demonstrate the utility of TOF-SIMS with PCA for the detection of the surface-grafted small molecules azidoaniline and a brominated furanone; imaging of the bromine ion peaks also enabled assessment of grafting uniformity. Thus, successful multilayer coating and furanone grafting was observed, and substantial and uniform coverage of furanone molecules on the surface. Even multiple grafting steps involving, in the present case, two low molecular weight compounds can readily be disentangled by PCA. The utility of TOF-SIMS analysis with PCA is particularly well illustrated in the present case by the grafting of the furanone molecules, which did not yield a singular unique peak in the positive ion mass spectra, whereas the collective spectral changes elucidated by PCA provided unambiguous verification of successful grafting of this low molecular weight compound.

Fimbrolide-coated antimicrobial lenses: their in vitro and in vivo effects.

PURPOSE: To examine the ability of contact lenses coated with fimbrolides, inhibitors of bacterial quorum sensing, to prevent microbial adhesion and their safety during short-term clinical assessment. METHODS: A fimbrolide was covalently attached to commercially available high Dk contact lenses. Subsequently Pseudomonas aeruginosa, Staphylococcus aureus, Serratia marcescens, or Acanthamoeba sp. were added to the lenses and control uncoated contact lenses. Lenses plus microbes were incubated for 24 h, then washed thoroughly to remove non-adherent microbes. Lenses were macerated and resulting slurry plated onto agar plates. After appropriate incubation, the numbers of colony forming units of bacteria (or numbers of Acanthamoeba trophozoites measured using a hemocytometer) from fimbrolide-coated and uncoated lenses were examined. A Guinea Pig model of lens wear was used to assess the safety of lenses worn on a continuous basis for 1 month. In a separate study, 10 subjects wore fimbrolide-coated lenses for 24 h. The responses of the Guinea Pigs and human volunteers to the lenses were assessed by slit lamp examination. RESULTS: The fimbrolides-coated lenses reduced the adhesion of all bacterial strains tested, with reductions occurring of between 67 and 92%. For Acanthamoeba a reduction of 70% was seen. There were no significant differences in ocular responses to fimbrolide-coated lenses compared with controls in either the 1 month animal model or overnight human trial. CONCLUSIONS: Fimbrolide-coated lenses show promise as an antibacterial and anti-acanthamoebal coating on contact lenses and appear to be safe when worn on the eye in an animal model.